Abstract: In this paper, a learning algorithm using neuronal networks to improve the roll stability and prevent the rollover in a single unit heavy vehicle is proposed. First, LQR control to keep balanced normalized rollovers, between front and rear axles, below the unity, then a data collected from this controller is used as a training basis of a neuronal regulator. The ANN controller is thereafter applied for the nonlinear side force model, and gives satisfactory results than the LQR one.
Abstract: Hydrogen produced by means of polymer electrolyte
membrane electrolyzer (PEME) is one of the most promising
methods due to clean and renewable energy source. In the process,
some energy loss due to mass transfer through a PEM is caused by
diffusion, electro-osmotic drag, and the pressure difference between
the cathode channel and anode channel. In PEME, water molecules
and ionic particles transferred between the electrodes from anode to
cathode, Extensive mixing of the hydrogen and oxygen at anode
channel due to gases cross-over must be avoided. In recent times the
consciousness of safety issue in high pressure PEME where the
oxygen mix with hydrogen at anode channel could create, explosive
conditions have generated a lot of concern. In this paper, the steady
state and simulation analysis of gases crossover in PEME on the
temperature and pressure effect are presented. The simulations have
been analysis in MATLAB based on the well-known Fick’s Law of
molecular diffusion. The simulation results indicated that as
temperature increases, there is a significant decrease in operating
voltage.
Abstract: In order to utilize results from global climate models,
dynamical and statistical downscaling techniques have been
developed. For dynamical downscaling, usually a limited area
numerical model is used, with associated high computational cost.
This research proposes dynamic equation for specific space-time
regional climate downscaling from the Educational Global Climate
Model (EdGCM) for Southeast Asia. The equation is for surface air
temperature. This equation provides downscaling values of surface
air temperature at any specific location and time without running a
regional climate model. In the proposed equations, surface air
temperature is approximated from ground temperature, sensible heat
flux and 2m wind speed. Results from the application of the equation
show that the errors from the proposed equations are less than the
errors for direct interpolation from EdGCM.
Abstract: Strong anthropogenic impact has uncontrolled
consequences on the nature of the soil. Hence, up-to-date sustainable
methods of soil state improvement are essential. Investigators provide
the evidence that biochar can positively effects physical, chemical,
and biological soil properties and the abundance of mycorrhizal fungi
which are in the focus of this study. The main aim of the present
investigation is to demonstrate the effect of two types of plant growth
promoting bacteria (PGPB) inoculums along with the beech wood
biochar and mineral N additives on mycorrhizal colonization.
Experiment has been set up in laboratory conditions with containers
filled with arable soil from the protection zone of the main water
source “Brezova nad Svitavou”. Lactuca sativa (lettuce) has been
selected as a model plant. Based on the obtained data, it can be
concluded that mycorrhizal colonization increased as the result of
combined influence of biochar and PGPB inoculums amendment. In
addition, correlation analyses showed that the numbers of main
groups of cultivated bacteria were dependent on the degree of
mycorrhizal colonization.
Abstract: This paper aimed to introduce the solution of concrete
slump recovery using chemical admixture type-F (superplasticizer,
naphthalene base) to the practice in order to solve unusable concrete
problem due to concrete loss its slump, especially for those tropical
countries that have faster slump loss rate. In the other hand, randomly
adding superplasticizer into concrete can cause concrete to segregate.
Therefore, this paper also develops the estimation model used to
calculate amount of second dose of superplasticizer need for concrete
slump recovery. Fresh properties of ordinary Portland cement
concrete with volumetric ratio of paste to void between aggregate
(paste content) of 1.1-1.3 with water-cement ratio zone of 0.30 to
0.67 and initial superplasticizer (naphthalene base) of 0.25%-1.6%
were tested for initial slump and slump loss for every 30 minutes for
one and half hour by slump cone test. Those concretes with slump
loss range from 10% to 90% were re-dosed and successfully
recovered back to its initial slump. Slump after re-dosed was tested
by slump cone test. From the result, it has been concluded that, slump
loss was slower for those mix with high initial dose of
superplasticizer due to addition of superplasticizer will disturb
cement hydration. The required second dose of superplasticizer was
affected by two major parameters, which were water-cement ratio
and paste content, where lower water-cement ratio and paste content
cause an increase in require second dose of superplasticizer. The
amount of second dose of superplasticizer is higher as the solid
content within the system is increase, solid can be either from cement
particles or aggregate. The data was analyzed to form an equation use
to estimate the amount of second dosage requirement of
superplasticizer to recovery slump to its original.
Abstract: The paper focuses on the benefits of business process
modeling. Although this discipline is developing for many years,
there is still necessity of creating new opportunities to meet the ever
increasing users’ needs. Because one of these needs is related to the
conversion of business process models from one standard to another,
the authors have developed a converter between BPMN and EPC
standards using workflow patterns as intermediate tool. Nowadays
there are too many systems for business process modeling. The
variety of output formats is almost the same as the systems
themselves. This diversity additionally hampers the conversion of the
models. The presented study is aimed at discussing problems due to
differences in the output formats of various modeling environments.
Abstract: Large quantities of solid wastes being generated
worldwide from sources such as household, domestic, industrial,
commercial and construction demolition activities, leads to
environmental concerns. Utilization of these wastes in making
building construction materials can reduce the magnitude of the
associated problems. When these waste products are used in place of
other conventional materials, natural resources and energy are
preserved and expensive and/or potentially harmful waste disposal is
avoided. Recycling which is regarded as the third most preferred waste
disposal option, with its numerous environmental benefits, stand as a
viable option to offset the environmental impact associated with the
construction industry. This paper reviews the results of laboratory tests and important
research findings, and the potential of using these wastes in building
construction materials with focus on sustainable development.
Research gaps, which includes; the need to develop standard mix
design for solid waste based building materials; the need to develop
energy efficient method of processing solid waste use in concrete; the
need to study the actual behavior or performance of such building
materials in practical application and the limited real life application
of such building materials have also been identified. A research is being proposed to develop an environmentally
friendly, lightweight building block from recycled waste paper,
without the use of cement, and with properties suitable for use as
walling unit. This proposed research intends to incorporate,
laboratory experimentation and modeling to address the identified
research gaps.
Abstract: Microcantilevers are the basic MEMS devices, which
can be used as sensors, actuators and electronics can be easily built
into them. The detection principle of microcantilever sensors is based
on the measurement of change in cantilever deflection or change in its
resonance frequency. The objective of this work is to explore the
analogies between mechanical and electrical equivalent of
microcantilever beams. Normally scientists and engineers working in
MEMS use expensive software like CoventorWare, IntelliSuite,
ANSYS/Multiphysics etc. This paper indicates the need of developing
electrical equivalent of the MEMS structure and with that, one can
have a better insight on important parameters, and their interrelation of
the MEMS structure. In this work, considering the mechanical model
of microcantilever, equivalent electrical circuit is drawn and using
force-voltage analogy, it is analyzed with circuit simulation software.
By doing so, one can gain access to powerful set of intellectual tools
that have been developed for understanding electrical circuits Later
the analysis is performed using ANSYS/Multiphysics - software based
on finite element method (FEM). It is observed that both mechanical
and electrical domain results for a rectangular microcantlevers are in
agreement with each other.
Abstract: Software quality issues require special attention
especially in view of the demands of quality software product to meet
customer satisfaction. Software development projects in most
organisations need proper defect management process in order to
produce high quality software product and reduce the number of
defects. The research question of this study is how to produce high
quality software and reducing the number of defects. Therefore, the
objective of this paper is to provide a framework for managing
software defects by following defined life cycle processes. The
methodology starts by reviewing defects, defect models, best
practices, and standards. A framework for defect management life
cycle is proposed. The major contribution of this study is to define a
defect management roadmap in software development. The adoption
of an effective defect management process helps to achieve the
ultimate goal of producing high quality software products and
contributes towards continuous software process improvement.
Abstract: Both steady and unsteady turbulent mixed convection
heat transfer in a 3D lid-driven enclosure, which has constant heat
flux on the middle of bottom wall and with isothermal moving
sidewalls, is reported in this paper for working fluid with Prandtl
number Pr = 0.71. The other walls are adiabatic and stationary. The
dimensionless parameters used in this research are Reynolds number,
Re = 5000, 10000 and 15000, and Richardson number, Ri = 1 and 10.
The simulations have been done by using different turbulent methods
such as RANS, URANS, and LES. The effects of using different k-ε
models such as standard, RNG and Realizable k-ε model are
investigated. Interesting behaviours of the thermal and flow fields
with changing the Re or Ri numbers are observed. Isotherm and
turbulent kinetic energy distributions and variation of local Nusselt
number at the hot bottom wall are studied as well. The local Nusselt
number is found increasing with increasing either Re or Ri number.
In addition, the turbulent kinetic energy is discernibly affected by
increasing Re number. Moreover, the LES results have shown good
ability of this method in predicting more detailed flow structures in
the cavity.
Abstract: Response Surface Methods (RSM) provide
statistically validated predictive models that can then be manipulated
for finding optimal process configurations. Variation transmitted to
responses from poorly controlled process factors can be accounted
for by the mathematical technique of propagation of error (POE),
which facilitates ‘finding the flats’ on the surfaces generated by
RSM. The dual response approach to RSM captures the standard
deviation of the output as well as the average. It accounts for
unknown sources of variation. Dual response plus propagation of
error (POE) provides a more useful model of overall response
variation. In our case, we implemented this technique in predicting
compressive strength of concrete of 28 days in age. Since 28 days is
quite time consuming, while it is important to ensure the quality
control process. This paper investigates the potential of using design
of experiments (DOE-RSM) to predict the compressive strength of
concrete at 28th day. Data used for this study was carried out from
experiment schemes at university of Benghazi, civil engineering
department. A total of 114 sets of data were implemented. ACI mix
design method was utilized for the mix design. No admixtures were
used, only the main concrete mix constituents such as cement, coarseaggregate,
fine aggregate and water were utilized in all mixes.
Different mix proportions of the ingredients and different water
cement ratio were used. The proposed mathematical models are
capable of predicting the required concrete compressive strength of
concrete from early ages.
Abstract: The aim of this paper is to propose a general
framework for storing, analyzing, and extracting knowledge from
two-dimensional echocardiographic images, color Doppler images,
non-medical images, and general data sets. A number of high
performance data mining algorithms have been used to carry out this
task. Our framework encompasses four layers namely physical
storage, object identification, knowledge discovery, user level.
Techniques such as active contour model to identify the cardiac
chambers, pixel classification to segment the color Doppler echo
image, universal model for image retrieval, Bayesian method for
classification, parallel algorithms for image segmentation, etc., were
employed. Using the feature vector database that have been
efficiently constructed, one can perform various data mining tasks
like clustering, classification, etc. with efficient algorithms along
with image mining given a query image. All these facilities are
included in the framework that is supported by state-of-the-art user
interface (UI). The algorithms were tested with actual patient data
and Coral image database and the results show that their performance
is better than the results reported already.
Abstract: This paper presents the results of a study on the
influence of varying percentages of rock bridges along a basal surface
defining a biplanar failure mode. A pseudo-coupled-hydromechanical
brittle fracture analysis is adopted using the state-of-the-art code
Slope Model. Model results show that rock bridge failure is strongly
influenced by the incorporation of groundwater pressures. The
models show that groundwater pressure can promote total failure of a
5% rock bridge along the basal surface. Once the percentage of the
rock bridges increases to 10 and 15%, although, the rock bridges are
broken, full interconnection of the surface defining the basal surface
of the biplanar mode does not occur. Increased damage is caused
when the rock bridge is located at the daylighting end of the basal
surface in proximity to the blast damage zone. As expected, some
cracking damage is experienced in the blast damage zone, where
properties representing a good quality controlled damage blast
technique were assumed. Model results indicate the potential increase
of permeability towards the blast damage zone.
Abstract: Laura Island, which is located about 50 km away from
downtown, is a source of water supply in Majuro atoll, which is the
capital of the Republic of the Marshall Islands. Low and flat Majuro
atoll has neither river nor lake. It is very important for Majuro atoll to
ensure the conservation of its water resources. However, upconing,
which is the process of partial rising of the freshwater-saltwater
boundary near the water-supply well, was caused by the excess
pumping from it during the severe drought in 1998. Upconing will
make the water usage of the freshwater lens difficult. Thus,
appropriate water usage is required to prevent up coning in the
freshwater lens because there is no other water source during drought. Numerical simulation of water usage applying SEAWAT model
was conducted at the central part of Laura Island, including the water
supply well, which was affected by upconing. The freshwater lens was
created as a result of infiltration of consistent average rainfall. The lens
shape was almost the same as the one in 1985. 0 of monthly rainfall
and variable daily pump discharge were used to calculate the
sustainable pump discharge from the water supply well. Consequently,
the total amount of pump discharge was increased as the daily pump
discharge was increased, indicating that it needs more time to recover
from upconing. Thus, a pump standard to reduce the pump intensity is
being proposed, which is based on numerical simulation concerning
the occurrence of the up-coning phenomenon in Laura Island during
the drought.
Abstract: The end panels of a large rectangular industrial duct,
which experience significant internal pressures, also experience
considerable transverse shear due to transfer of gravity loads to the
supports. The current design practice of such thin plate panels for
shear load is based on methods used for the design of plate girder
webs. The structural arrangements, the loadings and the resulting
behavior associated with the industrial duct end panels are, however,
significantly different from those of the web of a plate girder. The
large aspect ratio of the end panels gives rise to multiple bands of
tension fields, whereas the plate girder web design is based on one
tension field. In addition to shear, the industrial end panels are
subjected to internal pressure which in turn produces significant
membrane action. This paper reports a study which was undertaken
to review the current industrial analysis and design methods and to
propose a comprehensive method of designing industrial duct end
panels for shear resistance. In this investigation, a nonlinear finite element model was
developed to simulate the behavior of industrial duct end panel, along
with the associated edge stiffeners, subjected to transverse shear and
internal pressures. The model considered the geometric imperfections
and constitutive relations for steels. Six scale independent
dimensionless parameters that govern the behavior of such end panel
were identified and were then used in a parametric study. It was
concluded that the plate slenderness dominates the shear strength of
stockier end panels, and whereas, both the plate slenderness and the
aspect ratio influence the shear strength of slender end panels. Based
on these studies, this paper proposes design aids for estimating the
shear strength of rectangular duct end panels.
Abstract: The goal of this paper is to specify factors influencing
the profitability of selected banks. Next, a model will be created to
help establish variables that have a demonstrable influence on the
development of the selected banks' profitability ratios. Czech banks
and their international parent companies were selected for analyzing
profitability. Banks categorized as large banks (according to the
Czech National Bank's system, which ranks banks according to
balance sheet total) were selected to represent the Czech banks. Two
ratios, the return on assets ratio (ROA) and the return on equity ratio
(ROE) are used to assess bank profitability. Six endogenous and four
external indicators were selected from among other factors that
influence bank profitability. The data analyzed were for 2001–2013.
First, correlation analysis, which was supposed to eliminate
correlated values, was conducted. A large number of correlated
values were established on the basis of this analysis. The strongly
correlated values were omitted. Despite this, the subsequent
regression analysis of profitability for the individual banks that were
selected did not confirm that the selected variables influenced their
profitability. The studied factors' influence on bank profitability was
demonstrated only for Ceskoslovenska Obchodni Banka and Société
Générale using regression analysis. For Československa Obchodni
Banka, it was demonstrated that inflation level and the amount of the
central bank's interest rate influenced the return on assets ratio and
that capital adequacy and market concentration influenced the return
on equity ratio for Société Générale.
Abstract: Sentiment analysis means to classify a given review
document into positive or negative polar document. Sentiment
analysis research has been increased tremendously in recent times
due to its large number of applications in the industry and academia.
Sentiment analysis models can be used to determine the opinion of
the user towards any entity or product. E-commerce companies can
use sentiment analysis model to improve their products on the basis
of users’ opinion. In this paper, we propose a new One-class Support
Vector Machine (One-class SVM) based sentiment analysis model
for movie review documents. In the proposed approach, we initially
extract features from one class of documents, and further test the
given documents with the one-class SVM model if a given new test
document lies in the model or it is an outlier. Experimental results
show the effectiveness of the proposed sentiment analysis model.
Abstract: In this paper, approach to incoherent signal detection
in multi-element antenna array are researched and modeled. Two
types of useful signals with unknown wavefront were considered:
first one, deterministic (Barker code), and second one, random
(Gaussian distribution). The derivation of the sufficient statistics took
into account the linearity of the antenna array. The performance
characteristics and detecting curves are modeled and compared for
different useful signals parameters and for different number of
elements of the antenna array. Results of researches in case of some
additional conditions can be applied to a digital communications
systems.
Abstract: We present probabilistic multinomial Dirichlet
classification model for multidimensional data and Gaussian process
priors. Here, we have considered efficient computational method that
can be used to obtain the approximate posteriors for latent variables
and parameters needed to define the multiclass Gaussian process
classification model. We first investigated the process of inducing a
posterior distribution for various parameters and latent function by
using the variational Bayesian approximations and important sampling
method, and next we derived a predictive distribution of latent
function needed to classify new samples. The proposed model is
applied to classify the synthetic multivariate dataset in order to verify
the performance of our model. Experiment result shows that our model
is more accurate than the other approximation methods.
Abstract: Project Portfolio Management (PPM) is an essential
component of an organisation’s strategic procedures, which requires
attention of several factors to envisage a range of long-term outcomes
to support strategic project portfolio decisions. To evaluate overall
efficiency at the portfolio level, it is essential to identify the
functionality of specific projects as well as to aggregate those
findings in a mathematically meaningful manner that indicates the
strategic significance of the associated projects at a number of levels
of abstraction. PPM success is directly associated with the quality of
decisions made and poor judgment increases portfolio costs. Hence,
various Multi-Criteria Decision Making (MCDM) techniques have
been designed and employed to support the decision-making
functions. This paper reviews possible options to enhance the
decision-making outcomes in organisational portfolio management
processes using the Analytic Hierarchy Process (AHP) both from
academic and practical perspectives and will examine the usability,
certainty and quality of the technique. The results of the study will
also provide insight into the technical risk associated with current
decision-making model to underpin initiative tracking and strategic
portfolio management.