Abstract: Use of microemulsion in enhanced oil recovery has become more attractive in recent years because of its high level of extraction efficiency. Experimental investigations have been made on characterization of microemulsions of oil-brinesurfactant/ cosurfactant system for its use in enhanced oil recovery (EOR). Sodium dodecyl sulfate, propan-1-ol and heptane were selected as surfactant, cosurfactant and oil respectively for preparation of microemulsion. The effects of salinity on the relative phase volumes and solubilization parameters have also been studied. As salinity changes from low to high value, phase transition takes place from Winsor I to Winsor II via Winsor III. Suitable microemulsion composition has been selected based on its stability and ability to reduce interfacial tension. A series of flooding experiments have been performed using the selected microemulsion. The flooding experiments were performed in a core flooding apparatus using uniform sand pack. The core holder was tightly packed with uniform sands (60-100 mesh) and saturated with brines of different salinities. It was flooded with the brine at 25 psig and the absolute permeability was calculated from the flow rate of the through sand pack. The sand pack was then flooded with the crude oil at 800 psig to irreducible water saturation. The initial water saturation was determined on the basis of mass balance. Waterflooding was conducted by placing the coreholder horizontally at a constant injection pressure at 200 pisg. After water flooding, when water-cut reached above 95%, around 0.5 pore volume (PV) of the above microemulsion slug was injected followed by chasing water. The experiments were repeated using different composition of microemulsion slug. The additional recoveries were calculated by material balance. Encouraging results with additional recovery more than 20% of original oil in place above the conventional water flooding have been observed.
Abstract: This paper addresses the problem of trajectory
tracking control of an underactuated autonomous underwater vehicle
(AUV) in the horizontal plane. The underwater vehicle under
consideration is not actuated in the sway direction, and the system
matrices are not assumed to be diagonal and linear, as often found in
the literature. In addition, the effect of constant bias of environmental
disturbances is considered. Using backstepping techniques and the
tracking error dynamics, the system states are stabilized by forcing
the tracking errors to an arbitrarily small neighborhood of zero. The
effectiveness of the proposed control method is demonstrated through
numerical simulations. Simulations are carried out for an
experimental vehicle for smooth, inertial, two dimensional (2D)
reference trajectories such as constant velocity trajectory (a circle
maneuver – constant yaw rate), and time varying velocity trajectory
(a sinusoidal path – sinusoidal yaw rate).
Abstract: The problem of lot sizing, sequencing and scheduling
multiple products in flow line production systems has been studied
by several authors. Almost all of the researches in this area assumed
that setup times and costs are sequence –independent even though
sequence dependent setups are common in practice. In this paper we
present a new mixed integer non linear program (MINLP) and a
heuristic method to solve the problem in sequence dependent case.
Furthermore, a genetic algorithm has been developed which applies
this constructive heuristic to generate initial population. These two
proposed solution methods are compared on randomly generated
problems. Computational results show a clear superiority of our
proposed GA for majority of the test problems.
Abstract: A numerical study of flow in a horizontally channel
partially filled with a porous screen with non-uniform inlet has been
performed by lattice Boltzmann method (LBM). The flow in porous
layer has been simulated by the Brinkman-Forchheimer model.
Numerical solutions have been obtained for variable porosity models
and the effects of Darcy number and porosity have been studied in
detail. It is found that the flow stabilization is reliant on the Darcy
number. Also the results show that the stabilization of flow field and
heat transfer is depended to Darcy number. Distribution of stream
field becomes more stable by decreasing Darcy number. Results
illustrate that the effect of variable porosity is significant just in the
region of the solid boundary. In addition, difference between constant
and variable porosity models is decreased by decreasing the Darcy
number.
Abstract: This study investigated morphology of the Spanner Barb (Puntius lateristriga Valenciennes, 1842) and water quality at Thepchana waterfall. This study was conducted at Thepchana Waterfall, Khao Nan National Park from March to May 2007. There were 40 Spanner Barb collected with 20 males and 20 females. Males had an average of 5.57 cm in standard length, 6.62 cm in total length and 5.18 g in total body weight. Females had an average of 7.25 cm in standard length, 8.24 cm in total length and 10.96 g in total body weight. The length (L) – weight (W) relationships for combining sexes, males and females were LogW = -2.137 + 3.355logL, log W = -0.068 + 3.297logL, and log W = -2.068 + 3.297logL, respectively. The Spanner Barb were smaller size fish with a compressed form; terminal mouth; villiform teeth; ctenoid scale; concave tail; general body color yellowish olive, with slight reddish tint to fins; vertical band beginning below dorsal and horizontal stripe from base of tail almost to vertical band. They also had a vertical band midway between the eye and first vertical band. There was a black spot above anal fin. The bladder looked like J-shape. Inside of the bladder was found small insects and insect lava. The body length and the bowels length was 1:1 ratio. The water temperature ranged from 25.00 – 27.00 °C which was appropriate for their habitat characteristics. Acid - alkalinity ranged from 6.65 – 6.90 mg/l. Dissolved oxygen ranged from 4.55 – 4.70 mg/l. Water hardness ranged from 31.00 – 48.00 mg/l. The amount of ammonia was about 0.25 mg/l.
Abstract: An experimental study of Reinforced Concrete, RC, columns strengthened using a steel jacketing technique was conducted. The jacketing technique consisted of four steel vertical angles installed at the corners of the column joined by horizontal steel straps confining the column externally. The effectiveness of the technique was evaluated by testing the RC column specimens under eccentric monotonic loading until failure occurred. Strain gauges were installed to monitor the strains in the internal reinforcement as well as the external jacketing system. The effectiveness of the jacketing technique was demonstrated, and the parameters affecting the technique were studied.
Abstract: Today air-core coils (ACC) are a viable alternative to
ferrite-core coils in a range of applications due to their low induction
effect. An analytical study was carried out and the results were used as
a guide to understand the relationship between the magnet-coil
distance and the resulting attractive magnetic force. Four different
ACC models were fabricated for experimental study. The variation in
the models included the dimensions, the number of coil turns and the
current supply to the coil. Comparison between the analytical and
experimental results for all the models shows an average discrepancy
of less than 10%. An optimized ACC design was selected for the
scanner which can provide maximum magnetic force.
Abstract: The hidden-point bar method is useful in many
surveying applications. The method involves determining the
coordinates of a hidden point as a function of horizontal and vertical
angles measured to three fixed points on the bar. Using these
measurements, the procedure involves calculating the slant angles,
the distances from the station to the fixed points, the coordinates of
the fixed points, and then the coordinates of the hidden point. The
propagation of the measurement errors in this complex process has
not been fully investigated in the literature. This paper evaluates the
effect of the bar geometry on the position accuracy of the hidden
point which depends on the measurement errors of the horizontal and
vertical angles. The results are used to establish some guidelines
regarding the inclination angle of the bar and the location of the
observed points that provide the best accuracy.
Abstract: Iran is one of the greatest producers of date in the
world. However due to lack of information about its viscoelastic
properties, much of the production downgraded during harvesting
and postharvesting processes. In this study the effect of temperature
and moisture content of product were investigated on stress
relaxation characteristics. Therefore, the freshly harvested date
(kabkab) at tamar stage were put in controlled environment chamber
to obtain different temperature levels (25, 35, 45, and 55 0C) and
moisture contents (8.5, 8.7, 9.2, 15.3, 20, 32.2 %d.b.). A texture
analyzer TAXT2 (Stable Microsystems, UK) was used to apply
uniaxial compression tests. A chamber capable to control temperature
was designed and fabricated around the plunger of texture analyzer to
control the temperature during the experiment. As a new approach a
CCD camera (A4tech, 30 fps) was mounted on a cylindrical glass
probe to scan and record contact area between date and disk.
Afterwards, pictures were analyzed using image processing toolbox
of Matlab software. Individual date fruit was uniaxially compressed
at speed of 1 mm/s. The constant strain of 30% of thickness of date
was applied to the horizontally oriented fruit. To select a suitable
model for describing stress relaxation of date, experimental data were
fitted with three famous stress relaxation models including the
generalized Maxwell, Nussinovitch, and Pelege. The constant in
mentioned model were determined and correlated with temperature
and moisture content of product using non-linear regression analysis.
It was found that Generalized Maxwell and Nussinovitch models
appropriately describe viscoelastic characteristics of date fruits as
compared to Peleg mode.
Abstract: A theoretical study is conducted to design and explore
the effect of different parameters such as heat loads, the tube size of
piping system, wick thickness, porosity and hole size on the
performance and capability of a Loop Heat Pipe(LHP). This paper
presents a steady state model that describes the different phenomena
inside a LHP. Loop Heat Pipes(LHPs) are two-phase heat transfer
devices with capillary pumping of a working fluid. By their original
design comparing with heat pipes and special properties of the
capillary structure, they-re capable of transferring heat efficiency for
distances up to several meters at any orientation in the gravity field,
or to several meters in a horizontal position. This theoretical model is
described by different relations to satisfy important limits such as
capillary and nucleate boiling. An algorithm is developed to predict
the size of the LHP satisfying the limitations mentioned above for a
wide range of applied loads. Finally, to assess and evaluate the
algorithm and all the relations considered, we have used to design a
new kind of LHP to recover the heat from the exhaust of an actual
Gas Turbine. By finding the results, it showed that we can use the
LHP as a very high efficient device to recover the heat even in high
amount of loads(exhaust of a gas turbine). The sizes of all parts of the
LHP were obtained using the developed algorithm.
Abstract: Traditional wind tunnel models are meticulously machined from metal in a process that can take several months. While very precise, the manufacturing process is too slow to assess a new design's feasibility quickly. Rapid prototyping technology makes this concurrent study of air vehicle concepts via computer simulation and in the wind tunnel possible. This paper described the Affects layer thickness models product with rapid prototyping on Aerodynamic Coefficients for Constructed wind tunnel testing models. Three models were evaluated. The first model was a 0.05mm layer thickness and Horizontal plane 0.1μm (Ra) second model was a 0.125mm layer thickness and Horizontal plane 0.22μm (Ra) third model was a 0.15mm layer thickness and Horizontal plane 4.6μm (Ra). These models were fabricated from somos 18420 by a stereolithography (SLA). A wing-body-tail configuration was chosen for the actual study. Testing covered the Mach range of Mach 0.3 to Mach 0.9 at an angle-of-attack range of -2° to +12° at zero sideslip. Coefficients of normal force, axial force, pitching moment, and lift over drag are shown at each of these Mach numbers. Results from this study show that layer thickness does have an effect on the aerodynamic characteristics in general; the data differ between the three models by fewer than 5%. The layer thickness does have more effect on the aerodynamic characteristics when Mach number is decreased and had most effect on the aerodynamic characteristics of axial force and its derivative coefficients.
Abstract: Iris pattern is an important biological feature of human body; it becomes very hot topic in both research and practical applications. In this paper, an algorithm is proposed for iris recognition and a simple, efficient and fast method is introduced to extract a set of discriminatory features using first order gradient operator applied on grayscale images. The gradient based features are robust, up to certain extents, against the variations may occur in contrast or brightness of iris image samples; the variations are mostly occur due lightening differences and camera changes. At first, the iris region is located, after that it is remapped to a rectangular area of size 360x60 pixels. Also, a new method is proposed for detecting eyelash and eyelid points; it depends on making image statistical analysis, to mark the eyelash and eyelid as a noise points. In order to cover the features localization (variation), the rectangular iris image is partitioned into N overlapped sub-images (blocks); then from each block a set of different average directional gradient densities values is calculated to be used as texture features vector. The applied gradient operators are taken along the horizontal, vertical and diagonal directions. The low order norms of gradient components were used to establish the feature vector. Euclidean distance based classifier was used as a matching metric for determining the degree of similarity between the features vector extracted from the tested iris image and template features vectors stored in the database. Experimental tests were performed using 2639 iris images from CASIA V4-Interival database, the attained recognition accuracy has reached up to 99.92%.
Abstract: In order to apply partially filled steel grid composite deck as the horizontal supporting structure of various kinds of infrastructures, the variation of its flexural strength according to design parameters such as cross and longitudinal bars constituting the steel grid and the type of shear connection is evaluated and compared experimentally. The result shows that the design sensitivity of the deck to the spacing of the cross bars is insignificant in the case of structure with low risk of punching failure or without load distribution problem. By means of shear connection composed by transverse rebar and longitudinal bar without additional shear stud bolts, the complete interaction between steel grid and concrete slab is able to be achieved and the composite deck can develop its bending resistance capacity.
Abstract: Carbon Capture & Storage (CCS) is one of the various
methods that can be used to reduce the carbon footprint of the
energy sector. This paper focuses on the absorption of CO2 from
flue gas using packed columns, whose efficiency is highly dependent
on the structure of the liquid films within the column. To study the
characteristics of liquid films a CFD solver, OpenFOAM is utilised
to solve two-phase, isothermal film flow using the volume-of-fluid
(VOF) method. The model was validated using existing experimental
data and the Nusselt theory. It was found that smaller plate inclination
angles, with respect to the horizontal plane, resulted in larger wetted
areas on smooth plates. However, only a slight improvement in
the wetted area was observed. Simulations were also performed
using a ridged plate and it was observed that these surface textures
significantly increase the wetted area of the plate. This was mainly
attributed to the channelling effect of the ridges, which helped to
oppose the surface tension forces trying to minimise the surface area.
Rivulet formations on the ridged plate were also flattened out and
spread across a larger proportion of the plate width.
Abstract: Laminar natural-convective heat transfer from a
horizontal cylinder is studied by solving the Navier-Stokes and
energy equations using higher order compact scheme in cylindrical
polar coordinates. Results are obtained for Rayleigh numbers of 1,
10, 100 and 1000 for a Prandtl number of 0.7. The local Nusselt
number and mean Nusselt number are calculated and compared with
available experimental and theoretical results. Streamlines, vorticity -
lines and isotherms are plotted.
Abstract: How to simulate experimentally the air flow and heat
transfer under microgravity on the ground is important, which has not
been completely solved so far. Influence of gravity on air natural
convection results in convection heat transfer on ground difference
from that on orbit. In order to obtain air temperature and velocity
deviations of manned spacecraft during terrestrial thermal test,
dimensionless number analysis and numerical simulation analysis are
performed. The calculated temperature distribution and velocity
distribution of the horizontal test cases are compared to the vertical
cases. The results show that the influence of gravity is neglected for
facility drawer racks and more obvious for vertical cabins.
Abstract: In this paper, the dam-reservoir interaction is
analyzed using a finite element approach. The fluid is assumed to be
incompressible, irrotational and inviscid. The assumed boundary
conditions are that the interface of the dam and reservoir is vertical
and the bottom of reservoir is rigid and horizontal. The governing
equation for these boundary conditions is implemented in the
developed finite element code considering the horizontal and vertical
earthquake components. The weighted residual standard Galerkin
finite element technique with 8-node elements is used to discretize
the equation that produces a symmetric matrix equation for the damreservoir
system. A new boundary condition is proposed for
truncating surface of unbounded fluid domain to show the energy
dissipation in the reservoir, through radiation in the infinite upstream
direction. The Sommerfeld-s and perfect damping boundary
conditions are also implemented for a truncated boundary to compare
with the proposed far end boundary. The results are compared with
an analytical solution to demonstrate the accuracy of the proposed
formulation and other truncated boundary conditions in modeling the
hydrodynamic response of an infinite reservoir.
Abstract: We investigated a modified thermal evaporation
method in the growth process of ZnO nanowires. ZnO nanowires
were fabricated on p-type silicon substrates without using a metal
catalyst. A simple horizontal double-tube system along with
chemical vapor diffusion of the precursor was used to grow the ZnO
nanowires. The substrates were placed in different temperature
zones, and ZnO nanowires with different diameters were obtained for
the different substrate temperatures. In addition to the nanowires,
ZnO microdiscs with different diameters were obtained on another
substrate, which was placed at a lower temperature than the other
substrates. The optical properties and crystalline quality of the ZnO
nanowires and microdiscs were characterized by room temperature
photoluminescence (PL) and Raman spectrometers. The PL and
Raman studies demonstrated that the ZnO nanowires and microdiscs
grown using such set-up had good crystallinity with excellent optical
properties. Rectifying behavior of ZnO/Si heterostructures was
characterized by a simple DC circuit.
Abstract: Natural convection heat transfer from a heated
horizontal semi-circular cylinder (flat surface upward) has been
investigated for the following ranges of conditions; Grashof number,
and Prandtl number. The governing partial differential equations
(continuity, Navier-Stokes and energy equations) have been solved
numerically using a finite volume formulation. In addition, the role of
the type of the thermal boundary condition imposed at cylinder
surface, namely, constant wall temperature (CWT) and constant heat
flux (CHF) are explored. Natural convection heat transfer from a
heated horizontal semi-circular cylinder (flat surface upward) has
been investigated for the following ranges of conditions; Grashof
number, and Prandtl number, . The governing partial differential
equations (continuity, Navier-Stokes and energy equations) have
been solved numerically using a finite volume formulation. In
addition, the role of the type of the thermal boundary condition
imposed at cylinder surface, namely, constant wall temperature
(CWT) and constant heat flux (CHF) are explored. The resulting flow
and temperature fields are visualized in terms of the streamline and
isotherm patterns in the proximity of the cylinder. The flow remains
attached to the cylinder surface over the range of conditions spanned
here except that for and ; at these conditions, a separated flow
region is observed when the condition of the constant wall
temperature is prescribed on the surface of the cylinder. The heat
transfer characteristics are analyzed in terms of the local and average
Nusselt numbers. The maximum value of the local Nusselt number
always occurs at the corner points whereas it is found to be minimum
at the rear stagnation point on the flat surface. Overall, the average
Nusselt number increases with Grashof number and/ or Prandtl
number in accordance with the scaling considerations. The numerical
results are used to develop simple correlations as functions of
Grashof and Prandtl number thereby enabling the interpolation of the
present numerical results for the intermediate values of the Prandtl or
Grashof numbers for both thermal boundary conditions.
Abstract: In this paper, the effects of the restoring force device on the response of a space frame structure resting on sliding type of bearing with a restoring force device is studied. The NS component of the El - Centro earthquake and harmonic ground acceleration is considered for earthquake excitation. The structure is modeled by considering six-degrees of freedom (three translations and three rotations) at each node. The sliding support is modeled as a fictitious spring with two horizontal degrees of freedom. The response quantities considered for the study are the top floor acceleration, base shear, bending moment and base displacement. It is concluded from the study that the displacement of the structure reduces by the use of the restoring force device. Also, the peak values of acceleration, bending moment and base shear also decreases. The simulation results show the effectiveness of the developed and proposed method.