Abstract: Computer based geostatistical methods can offer effective data analysis possibilities for agricultural areas by using
vectorial data and their objective informations. These methods will help to detect the spatial changes on different locations of the large
agricultural lands, which will lead to effective fertilization for optimal yield with reduced environmental pollution. In this study, topsoil (0-20 cm) and subsoil (20-40 cm) samples were taken from a
sugar beet field by 20 x 20 m grids. Plant samples were also collected
from the same plots. Some physical and chemical analyses for these
samples were made by routine methods. According to derived variation coefficients, topsoil organic matter (OM) distribution was more than subsoil OM distribution. The highest C.V. value of
17.79% was found for topsoil OM. The data were analyzed
comparatively according to kriging methods which are also used
widely in geostatistic. Several interpolation methods (Ordinary,Simple and Universal) and semivariogram models (Spherical,
Exponential and Gaussian) were tested in order to choose the suitable
methods. Average standard deviations of values estimated by simple
kriging interpolation method were less than average standard
deviations (topsoil OM ± 0.48, N ± 0.37, subsoil OM ± 0.18) of measured values. The most suitable interpolation method was simple
kriging method and exponantial semivariogram model for topsoil,
whereas the best optimal interpolation method was simple kriging
method and spherical semivariogram model for subsoil. The results
also showed that these computer based geostatistical methods should
be tested and calibrated for different experimental conditions and semivariogram models.
Abstract: The rate of nitrate adsorption by a nitrate selective ion
exchange resin was investigated in a well-stirred batch experiments.
The kinetic experimental data were simulated with diffusion models including external mass transfer, particle diffusion and chemical
adsorption. Particle pore volume diffusion and particle surface diffusion were taken into consideration separately and simultaneously
in the modeling. The model equations were solved numerically using the Crank-Nicholson scheme. An optimization technique was
employed to optimize the model parameters. All nitrate concentration
decay data were well described with the all diffusion models. The
results indicated that the kinetic process is initially controlled by external mass transfer and then by particle diffusion. The external
mass transfer coefficient and the coefficients of pore volume diffusion and surface diffusion in all experiments were close to each
other with the average value of 8.3×10-3 cm/S for external mass
transfer coefficient. In addition, the models are more sensitive to the
mass transfer coefficient in comparison with particle diffusion. Moreover, it seems that surface diffusion is the dominant particle
diffusion in comparison with pore volume diffusion.
Abstract: The environmental impact caused by industries is an issue that, in the last 20 years, has become very important in terms of society, economics and politics in Colombia. Particularly, the tannery process is extremely polluting because of uneffective treatments and regulations given to the dumping process and atmospheric emissions. Considering that, this investigation is intended to propose a management model based on the integration of Lean Supply Chain, Green Supply Chain, Cleaner Production and ISO 14001-2004, that prioritizes the strategic components of the organizations. As a result, a management model will be obtained and it will provide a strategic perspective through a systemic approach to the tanning process. This will be achieved through the use of Multicriteria Decision tools, along with Quality Function Deployment and Fuzzy Logic. The strategic approach that embraces the management model using the alignment of Lean Supply Chain, Green Supply Chain, Cleaner Production and ISO 14001-2004, is an integrated perspective that allows a gradual frame of the tactical and operative elements through the correct setting of the information flow, improving the decision making process. In that way, Small Medium Enterprises (SMEs) could improve their productivity, competitiveness and as an added value, the minimization of the environmental impact. This improvement is expected to be controlled through a Dashboard that helps the Organization measure its performance along the implementation of the model in its productive process.
Abstract: The value of emission factor was calculated in the
older type of Diesel engine operating on an engine testing bench and
then compared with the parameters monitored under similar
conditions when the EnviroxTM additive was applied. It has been
found out that the additive based on CeO2 nanoparticles reduces
emission of NOx. The dependencies of NOx emissions on reduced
torque, engine power and revolutions have been observed as well.
Abstract: This paper aims to improve a fine lapping process of
hard disk drive (HDD) lapping machines by removing materials from
each slider together with controlling the strip height (SH) variation to
minimum value. The standard deviation is the key parameter to
evaluate the strip height variation, hence it is minimized. In this
paper, a design of experiment (DOE) with factorial analysis by twoway
analysis of variance (ANOVA) is adopted to obtain a
statistically information. The statistics results reveal that initial stripe
height patterns affect the final SH variation. Therefore, initial SH
classification using a radial basis function neural network is
implemented to achieve the proportional gain prediction.
Abstract: We present a hybrid architecture of recurrent neural
networks (RNNs) inspired by hidden Markov models (HMMs). We
train the hybrid architecture using genetic algorithms to learn and
represent dynamical systems. We train the hybrid architecture on a
set of deterministic finite-state automata strings and observe the
generalization performance of the hybrid architecture when presented
with a new set of strings which were not present in the training data
set. In this way, we show that the hybrid system of HMM and RNN
can learn and represent deterministic finite-state automata. We ran
experiments with different sets of population sizes in the genetic
algorithm; we also ran experiments to find out which weight
initializations were best for training the hybrid architecture. The
results show that the hybrid architecture of recurrent neural networks
inspired by hidden Markov models can train and represent dynamical
systems. The best training and generalization performance is
achieved when the hybrid architecture is initialized with random real
weight values of range -15 to 15.
Abstract: Cogeneration may be defined as a system which
contains electricity production and regain of the thermo value of
exhaust gases simultaneously. The examination is based on the data-s
of an active cogeneration plant. This study, it is aimed to determine
which component of the system should be revised first to raise the
efficiency and decrease the loss of exergy. For this purpose, second
law analysis of thermodynamics is applied to each component due to
consider the effects of environmental conditions and take the quality
of energy into consideration as well as the quantity of it. The exergy
balance equations are produced and exergy loss is calculated for each
component. 44,44 % loss of exergy in heat exchanger, 29,59 % in
combustion chamber, 18,68 % in steam boiler, 5,25 % in gas turbine
and 2,03 % in compressor is calculated.
Abstract: Attempt was made to improve certain characteristics of bio-oil derived from palm kernel pyrolysis by blending it with diesel fuel and alcohols. Two types of alcohol, ethanol or butanol, was used as cosolvent to stabilize the phase of ternary systems. Phase behaviors and basic fuel properties of palm kernel bio-oildiesel- alcohol systems were investigated in this study. Alcohol types showed a significant influence on the phase characteristics with palm kernel bio-oil-diesel-butanol system giving larger soluble area than that of palm kernel bio-oil-diesel-ethanol system. For fuel properties, blended fuels showed superior properties including lower values of density (~860 kg/m3 at 25°C), viscosity (~4.12 mm2/s at 40°C), carbon residue (1.02-2.53 wt%), ash (0.018-0.034 wt%) and pour point (
Abstract: Horizontal wells are proven to be better producers
because they can be extended for a long distance in the pay zone.
Engineers have the technical means to forecast the well productivity
for a given horizontal length. However, experiences have shown that
the actual production rate is often significantly less than that of
forecasted. It is a difficult task, if not impossible to identify the real
reason why a horizontal well is not producing what was forecasted.
Often the source of problem lies in the drilling of horizontal section
such as permeability reduction in the pay zone due to mud invasion
or snaky well patterns created during drilling. Although drillers aim
to drill a constant inclination hole in the pay zone, the more frequent
outcome is a sinusoidal wellbore trajectory. The two factors, which
play an important role in wellbore tortuosity, are the inclination and
side force at bit. A constant inclination horizontal well can only be
drilled if the bit face is maintained perpendicular to longitudinal axis
of bottom hole assembly (BHA) while keeping the side force nil at
the bit. This approach assumes that there exists no formation force at
bit. Hence, an appropriate BHA can be designed if bit side force and
bit tilt are determined accurately. The Artificial Neural Network
(ANN) is superior to existing analytical techniques. In this study, the
neural networks have been employed as a general approximation tool
for estimation of the bit side forces. A number of samples are
analyzed with ANN for parameters of bit side force and the results
are compared with exact analysis. Back Propagation Neural network
(BPN) is used to approximation of bit side forces. Resultant low
relative error value of the test indicates the usability of the BPN in
this area.
Abstract: The purpose of this paper is to provide a practical
example to the Linear Quadratic Gaussian (LQG) controller. This
method includes a description and some discussion of the discrete
Kalman state estimator. One aspect of this optimality is that the
estimator incorporates all information that can be provided to it. It
processes all available measurements, regardless of their precision, to
estimate the current value of the variables of interest, with use of
knowledge of the system and measurement device dynamics, the
statistical description of the system noises, measurement errors, and
uncertainty in the dynamics models.
Since the time of its introduction, the Kalman filter has been the
subject of extensive research and application, particularly in the area
of autonomous or assisted navigation. For example, to determine the
velocity of an aircraft or sideslip angle, one could use a Doppler
radar, the velocity indications of an inertial navigation system, or the
relative wind information in the air data system. Rather than ignore
any of these outputs, a Kalman filter could be built to combine all of
this data and knowledge of the various systems- dynamics to
generate an overall best estimate of velocity and sideslip angle.
Abstract: Cast metal inlays can be used on molars requiring a
class II restoration instead amalgam and offer a durable alternative.
Because it is known that class II inlays may increase the
susceptibility to fracture, it is important to ensure optimal
performance in selection of the adequate preparation design to reduce
stresses in teeth structures and also in the restorations. The aim of the
study was to investigate the influence of preparation design on stress
distribution in molars with different class II preparations and in cast
metal inlays. The first step of the study was to achieve 3D models in
order to analyze teeth and cast metal class II inlays. The geometry of
the intact tooth was obtained by 3D scanning using a manufactured
device. With a NURBS modeling program the preparations and the
appropriately inlays were designed. 3D models of first upper molars
of the same shape and size were created. Inlay cavities designs were
created using literature data. The geometrical model was exported
and the mesh structure of the solid 3D model was created for
structural simulations. Stresses were located around the occlusal
contact areas. For the studied cases, the stress values were not
significant influenced by the taper of the preparation. it was
demonstrated stresses are higher in the cast metal restorations and
therefore the strength of the teeth is not affected.
Abstract: Experiments were carried out on the survival and growth of Rasbora daniconius, Puntius ticto and Puntius conchonius. The motivation of the study was to obtain information for growing the fish on a commercial scale for their use as biological control agents against mosquito larvae. The effects of temperature, total hardness, DO, pH and feed on the growth of fish were also investigated. Excessive value of total hardness was found because very rich calcium ion is present in Chitrakoot area. There was significant increases in growth rates of fish as temperature was increased from 280C to 300C. Further increases in temperature up to 320C, did not further affect growth. The positive and highly significant correlations 0.991488, 0.9581 and 0.9935 were found between length and weight of P. ticto, P. conchonius and R. daniconius respectively. The regression was significant at 5% level of probability.
Abstract: Image registration plays an important role in the
diagnosis of dental pathologies such as dental caries, alveolar bone
loss and periapical lesions etc. This paper presents a new wavelet
based algorithm for registering noisy and poor contrast dental x-rays.
Proposed algorithm has two stages. First stage is a preprocessing
stage, removes the noise from the x-ray images. Gaussian filter has
been used. Second stage is a geometric transformation stage.
Proposed work uses two levels of affine transformation. Wavelet
coefficients are correlated instead of gray values. Algorithm has been
applied on number of pre and post RCT (Root canal treatment)
periapical radiographs. Root Mean Square Error (RMSE) and
Correlation coefficients (CC) are used for quantitative evaluation.
Proposed technique outperforms conventional Multiresolution
strategy based image registration technique and manual registration
technique.
Abstract: ebXML (Electronic Business using eXtensible
Markup Language) is an e-business standard, sponsored by
UN/CEFACT and OASIS, which enables enterprises to exchange
business messages, conduct trading relationships, communicate
data in common terms and define and register business
processes. While there is tremendous e-business value in the
ebXML, security remains an unsolved problem and one of the
largest barriers to adoption. XML security technologies emerging
recently have extensibility and flexibility suitable for security
implementation such as encryption, digital signature, access
control and authentication.
In this paper, we propose ebXML business transaction models
that allow trading partners to securely exchange XML based
business transactions by employing XML security technologies.
We show how each XML security technology meets the ebXML
standard by constructing the test software and validating messages
between the trading partners.
Abstract: This paper presents the design, development and characterization of contractile water jet thruster (CWJT) for mini underwater robot. Instead of electric motor, this CWJT utilizes the Ionic Polymer Metal Composite (IPMC) as the actuator to generate the water jet. The main focus of this paper is to analyze the conceptual design of the proposed CWJT which would determine the thrust force value, jet flow behavior and actuator’s stress. Those thrust force and jet flow studies were carried out using Matlab/Simscape simulation software. The actuator stress had been analyzed using COSMOS simulation software. The results showed that there was no significant change for jet velocity at variable cross sectional nozzle area. However, a significant change was detected for jet velocity at different nozzle cross sectional area ratio which was up to 37%. The generated thrust force has proportional relation to the nozzle cross sectional area.
Abstract: Although, it is a long time that human know about
the importance of environment in life, but at the last decade of 20
century, the space that was full of hot scientific, collegial and
political were made in environmental challenge, So much that, this
problem not only disarrange the peace and security of life, but also it
has threatened human existence. One of the problems in last years
that are significant for authorities is unsatisfactory achieved results
against of using huge cost for magnificent environmental projects.
This subject leads thinker to this thought that for solving the
environmental problems it is needed new methods include of
sociology, ethics and philosophic, etc. methods apart of technical
affairs. Environment ethics is a new branch of philosophic ethics
discussion that discusses about the ethics relationship between
humans and universe that is around them. By notifying to the above
considered affairs, in today world, necessity of environmental ethics
for environment management is reduplicated. In the following the
article has been focused on environmental ethics role and
environmental management methods and techniques for developing
it.
Abstract: The production and consumption of natural gas is on
the rise throughout the world as a result of its wide availability, ease
of transportation, use and clean-burning characteristics. The chief use
of ethane is in the chemical industry in the production of Ethene
(ethylene) by steam cracking. In this simulation, obtained ethane
recovery percent based on Gas sub-cooled process (GSP) is 99.9 by
mole that is included 32.1% by using de-methanizer column and
67.8% by de-ethanizer tower. The outstanding feature of this process
is the novel split-vapor concept that employs to generate reflux for
de-methanizer column. Remain amount of ethane in export gas cause
rise in gross heating value up to 36.66 MJ/Nm3 in order to use in
industrial and household consumptions.
Abstract: The quality improvements of the environmental
elements could increase the recreational opportunities in a certain
area (destination). The technique of the need for recreation focuses
on choosing certain destinations for recreational purposes. The basic
exchange taken into consideration is the one between the satisfaction
gained after staying in that area and the value expressed in money
and time allocated. The number of tourists in the respective area, the
duration of staying and the money spent including transportation
provide information on how individuals rank the place or certain
aspects of the area (such as the quality of the environmental
elements).
For the statistical analysis of the environmental benefits offered by
an area through the need of recreation technique, the following stages
are suggested:
- characterization of the reference area based on the
statistical variables considered;
- estimation of the environmental benefit through
comparing the reference area with other similar areas
(having the same environmental characteristics), from
the perspective of the statistical variables considered.
The model compared in recreation technique faced with a series of
difficulties which refers to the reference area and correct
transformation of time in money.
Abstract: This paper proposes rough set models with three
different level knowledge granules in incomplete information system
under tolerance relation by similarity between objects according to
their attribute values. Through introducing dominance relation on the
discourse to decompose similarity classes into three subclasses: little
better subclass, little worse subclass and vague subclass, it dismantles
lower and upper approximations into three components. By using
these components, retrieving information to find naturally hierarchical
expansions to queries and constructing answers to elaborative queries
can be effective. It illustrates the approach in applying rough set
models in the design of information retrieval system to access different
granular expanded documents. The proposed method enhances rough
set model application in the flexibility of expansions and elaborative
queries in information retrieval.
Abstract: Bubble generation was observed using a high-speed
camera in subcooled flow boiling at low void fraction. Constant heat
flux was applied on one side of an upward rectangular channel to
make heated test channel. Water as a working fluid from high
subcooling to near saturation temperature was injected step by step to
investigate bubble behavior during void development. Experiments
were performed in two different pressures condition close to 2bar and
4bar. It was observed that in high subcooling when boiling was
commenced, bubble after nucleation departed its origin and slid
beside heated surface. In an observation window mean release
frequency of bubble fb,mean, nucleation site Ns and mean bubble
volume Vb,mean in each step of experiments were measured to
investigate wall vaporization rate. It was found that in proximity of
PNVG vaporization rate was increased significantly in compare with
condensation rate which remained in low value.