Abstract: Modular structural systems are constructed using a
method that they are assembled with prefabricated unit modular
frames on-site. This provides a benefit that can significantly reduce
building construction time. The structural design is usually carried out
under the assumption that their load-carrying mechanism is similar to
that of traditional steel moment-resisting systems. However, both
systems are different in terms of beam-column connection details
which may strongly influence the lateral structural behavior. Specially,
the presence of access holes in a beam-column joint of a unit modular
frame could cause undesirable failure during strong earthquakes.
Therefore, this study carried out finite element analyses (FEMs) of
unit modular frames to investigate the cyclic behavior of beam-column
joints with the access holes. Analysis results show that the unit
modular frames present stable cyclic response with large deformation
capacities and their joints are classified into semi-rigid connections
even if there are access holes.
Abstract: The Simulation based VLSI Implementation of
FELICS (Fast Efficient Lossless Image Compression System)
Algorithm is proposed to provide the lossless image compression and
is implemented in simulation oriented VLSI (Very Large Scale
Integrated). To analysis the performance of Lossless image
compression and to reduce the image without losing image quality
and then implemented in VLSI based FELICS algorithm. In FELICS
algorithm, which consists of simplified adjusted binary code for
Image compression and these compression image is converted in
pixel and then implemented in VLSI domain. This parameter is used
to achieve high processing speed and minimize the area and power.
The simplified adjusted binary code reduces the number of arithmetic
operation and achieved high processing speed. The color difference
preprocessing is also proposed to improve coding efficiency with
simple arithmetic operation. Although VLSI based FELICS
Algorithm provides effective solution for hardware architecture
design for regular pipelining data flow parallelism with four stages.
With two level parallelisms, consecutive pixels can be classified into
even and odd samples and the individual hardware engine is
dedicated for each one. This method can be further enhanced by
multilevel parallelisms.
Abstract: Passing the entrance exam to a university is a major
step in one's life. University entrance exam commonly known as
Kankor is the nationwide entrance exam in Afghanistan. This
examination is prerequisite for all public and private higher education
institutions at undergraduate level. It is usually taken by students who
are graduated from high schools. In this paper, we reflect the major
educational school graduates issues and propose ICT-based test
preparation environment, known as ‘Online Kankor Exam Prep
System’ to give students the tools to help them pass the university
entrance exam on the first try. The system is based on Intelligent
Tutoring System (ITS), which introduced an essential package of
educational technology for learners that features: (I) exam-focused
questions and content; (ii) self-assessment environment; and (iii) test
preparation strategies in order to help students to acquire the necessary
skills in their carrier and keep them up-to-date with instruction.
Abstract: This paper describes a novel application of Fiber
Braggs Grating (FBG) sensors in the assessment of human postural
stability and balance on an unstable platform. In this work, FBG
sensor Stability Analyzing Device (FBGSAD) is developed for
measurement of plantar strain to assess the postural stability of
subjects on unstable platforms during different stances in eyes open
and eyes closed conditions on a rocker board. The studies are
validated by comparing the Centre of Gravity (CG) variations
measured on the lumbar vertebra of subjects using a commercial
accelerometer. The results obtained from the developed FBGSAD
depict qualitative similarities with the data recorded by commercial
accelerometer. The advantage of the FBGSAD is that it measures
simultaneously plantar strain distribution and postural stability of the
subject along with its inherent benefits like non-requirement of
energizing voltage to the sensor, electromagnetic immunity and
simple design which suits its applicability in biomechanical
applications. The developed FBGSAD can serve as a tool/yardstick to
mitigate space motion sickness, identify individuals who are
susceptible to falls and to qualify subjects for balance and stability,
which are important factors in the selection of certain unique
professionals such as aircraft pilots, astronauts, cosmonauts etc.
Abstract: The most important component affecting the
efficiency of photovoltaic power systems are solar panels. In other
words, efficiency of these systems are significantly affected due to
the being low efficiency of solar panel. Thus, solar panels should be
operated under maximum power point conditions through a power
converter. In this study, design of boost converter has been carried
out with maximum power point tracking (MPPT) algorithm which is
incremental conductance (Inc-Cond). By using this algorithm,
importance of power converter in MPPT hardware design, impacts of
MPPT operation have been shown. It is worth noting that initial
operation point is the main criteria for determining the MPPT
performance. In addition, it is shown that if value of load resistance is
lower than critical value, failure operation is realized. For these
analyzes, direct duty control is used for simplifying the control.
Abstract: This paper presents a new structure of microstrip band
pass filter (BPF) based on coupled stepped impedance resonators.
Each filter consists of two coupled stepped impedance resonators
connected to microstrip feed lines. The coupled junction is utilized to
connect the two BPFs to the antenna. This two band pass filters are
designed and simulated to operate for the digital communication
system (DCS) and Industrial Scientific and Medical (ISM) bands at
1.8 GHz and 2.45 GHz respectively. The proposed circuit presents
good performances with an insertion loss lower than 2.3 dB and
isolation between the two channels greater than 21 dB. The prototype
of the optimized diplexer have been investigated numerically by
using ADS Agilent and verified with CST microwave software.
Abstract: Climate change confronts the built environment with
many new challenges in the form of more severe and frequent hydrometeorological
events. A series of strategies is proposed whereby the
various aspects of buildings and their sites can be made more resilient
to the effects of such events.
Abstract: Over the last few decades, oilfield service rolling
equipment has significantly increased in weight, primarily because of
emissions regulations, which require larger/heavier engines, larger
cooling systems, and emissions after-treatment systems, in some
cases, etc. Larger engines cause more vibration and shock loads,
leading to failure of electronics and control systems.
If the vibrating frequency of the engine matches the system
frequency, high resonance is observed on structural parts and mounts.
One such existing automated control equipment system comprising
wire rope mounts used for mounting computers was designed
approximately 12 years ago. This includes the use of an industrialgrade
computer to control the system operation. The original
computer had a smaller, lighter enclosure. After a few years, a newer
computer version was introduced, which was 10 lbm heavier. Some
failures of internal computer parts have been documented for cases in
which the old mounts were used. Because of the added weight, there
is a possibility of having the two brackets impact each other under
off-road conditions, which causes a high shock input to the computer
parts. This added failure mode requires validating the existing mount
design to suit the new heavy-weight computer.
This paper discusses the modal finite element method (FEM)
analysis and experimental modal analysis conducted to study the
effects of vibration on the wire rope mounts and the computer. The
existing mount was modelled in ANSYS software, and resultant
mode shapes and frequencies were obtained. The experimental modal
analysis was conducted, and actual frequency responses were
observed and recorded.
Results clearly revealed that at resonance frequency, the brackets
were colliding and potentially causing damage to computer parts. To
solve this issue, spring mounts of different stiffness were modeled in
ANSYS software, and the resonant frequency was determined.
Increasing the stiffness of the system increased the resonant
frequency zone away from the frequency window at which the engine
showed heavy vibrations or resonance. After multiple iterations in
ANSYS software, the stiffness of the spring mount was finalized,
which was again experimentally validated.
Abstract: The recommended limit for cadmium concentration in
potable water is less than 0.005 mg/L. A continuous biosorption
process using indigenous red seaweed, Gracilaria corticata, was
performed to remove cadmium from the potable water. The process
was conducted under fixed conditions and the breakthrough curves
were achieved for three consecutive sorption-desorption cycles. A
modeling based on Artificial Neural Network (ANN) was employed
to fit the experimental breakthrough data. In addition, a simplified
semi empirical model, Thomas, was employed for this purpose. It
was found that ANN well described the experimental data (R2>0.99)
while the Thomas prediction were a bit less successful with R2>0.97.
The adjusted design parameters using the nonlinear form of Thomas
model was in a good agreement with the experimentally obtained
ones. The results approve the capability of ANN to predict the
cadmium concentration in potable water.
Abstract: Background: Taiwan now is an aging society. Research
on the elderly should not be confined to caring for seniors, but should
also be focused on ways to improve health and the quality of life.
Senior citizens who participate in volunteer services could become
less lonely, have new growth opportunities, and regain a sense of
accomplishment. Thus, the question of how to get the elderly to
participate in volunteer service is worth exploring. Objective: Apply
the Transtheoretical Model to understand stages of change in regular
volunteer service and voluntary service behaviour among the seniors.
Methods: 1525 adults over the age of 65 from the Renai district of
Keelung City were interviewed. The research tool was a
self-constructed questionnaire, and individual interviews were
conducted to collect data. Then the data was processed and analyzed
using the IBM SPSS Statistics 20 (Windows version) statistical
software program. Results: In the past six months, research subjects
averaged 9.92 days of volunteer services. A majority of these elderly
individuals had no intention to change their regular volunteer services.
We discovered that during the maintenance stage, the self-efficacy for
volunteer services was higher than during all other stages, but
self-perceived barriers were less during the preparation stage and
action stage. Self-perceived benefits were found to have an important
predictive power for those with regular volunteer service behaviors in
the previous stage, and self-efficacy was found to have an important
predictive power for those with regular volunteer service behaviors in
later stages. Conclusions/Implications for Practice: The research
results support the conclusion that community nursing staff should
group elders based on their regular volunteer services change stages
and design appropriate behavioral change strategies.
Abstract: The objective of the present study is to determine
better eye end design of a mono leaf spring used in light motor
vehicle. A conventional 65Si7 spring steel leaf spring model with
standard eye, casted and riveted eye end are considered. The CAD
model of the leaf springs is prepared in CATIA and analyzed using
ANSYS. The standard eye, casted and riveted eye leaf springs are
subjected to similar loading conditions. The CAE analysis of the leaf
spring is performed for various parameters like deflection and Von-
Mises stress. Mass reduction of 62.9% is achieved in case of riveted
eye mono leaf spring as compared to standard eye mono leaf spring
for the same loading conditions.
Abstract: This paper provides a comparative study on the
performances of standard PID and adaptive PID controllers tested on
travel angle of a 3-Degree-of-Freedom (3-DOF) Quanser bench-top
helicopter. Quanser, a well-known manufacturer of educational
bench-top helicopter has developed Proportional Integration
Derivative (PID) controller with Linear Quadratic Regulator (LQR)
for all travel, pitch and yaw angle of the bench-top helicopter. The
performance of the PID controller is relatively good; however, its
performance could also be improved if the controller is combined
with adaptive element. The objective of this research is to design
adaptive PID controller and then compare the performances of the
adaptive PID with the standard PID. The controller design and test is
focused on travel angle control only. Adaptive method used in this
project is self-tuning controller, which controller’s parameters are
updated online. Two adaptive algorithms those are pole-placement
and deadbeat have been chosen as the method to achieve optimal
controller’s parameters. Performance comparisons have shown that
the adaptive (deadbeat) PID controller has produced more desirable
performance compared to standard PID and adaptive (poleplacement).
The adaptive (deadbeat) PID controller attained very fast
settling time (5 seconds) and very small percentage of overshoot (5%
to 7.5%) for 10° to 30° step change of travel angle.
Abstract: Science and technology has a major impact on many
societal domains such as communication, medicine, food,
transportation, etc. However, this dominance of modern technology
can have a negative unintended impact on indigenous systems, and in
particular on indigenous foods. This problem serves as a motivation
to this study whose aim is to examine the perceptions of learners on
the usefulness of Information and Communication Technologies
(ICTs) for learning about indigenous foods. This aim will be
subdivided into two types of research objectives. The design and
identification of theories and models will be achieved using literature
content analysis. The objective on the empirical testing of such
theories and models will be achieved through the survey of
Hospitality studies learners from different schools in the iLembe and
Umgungundlovu Districts of the South African Kwazulu-Natal
province. SPSS is used to quantitatively analyze the data collected by
the questionnaire of this survey using descriptive statistics and
Pearson correlations after the assessment of the validity and the
reliability of the data. The main hypothesis behind this study is that
there is a connection between the demographics of learners, their
perceptions on the usefulness of ICTs for learning about indigenous
foods, and the following personality and eLearning related theories
constructs: Computer self-efficacy, Trust in ICT systems, and
Conscientiousness; as suggested by existing studies on learning
theories. This hypothesis was fully confirmed by the survey
conducted by this study except for the demographic factors where
gender and age were not found to be determinant factors of learners’
perceptions on the usefulness of ICTs for learning about indigenous
foods.
Abstract: Cross flow water tube heat exchanger can be designed
and made operational using methods of model building and
simulation of the system. This paper projects the design and
development of a model of cross flow water tube heat-exchanger
system, simulation and validation of control analysis of different
tuning methods. Feedback and override control system is developed
using inputs acquired with the help of sensory system. A
mathematical model is formulated for analysis of system behaviour.
The temperature is regulated at the desired set point automatically.
Abstract: Systems Engineering plays a key role during industrial
product development of complex technical systems. The need for
systems engineers in industry is growing. But there is a gap between
the industrial need and the academic education. Normally the
academic education is focused on the domain specific design,
implementation and testing of technical systems. Necessary systems
engineering expertise like knowledge about requirements analysis,
product cost estimation, management or social skills are poorly
taught. Thus there is the need of new academic concepts for teaching
systems engineering skills. This paper presents a project-orientated
training concept to prepare students from different technical degree
programs for systems engineering activities. The training concept has
been initially implemented and applied in the industrial engineering
master program of the University of Applied Sciences Offenburg.
Abstract: The problematic of gender and socioeconomic status
biased differences in academic motivation patterns is discussed.
Gender identity is understood according to symbolic interactionism
perspective: as a result of reflected appraisals, social comparisons,
self-attributions, and identifications, shaped by social environment
and family context. The effects of socioeconomic status on academic
motivation are conceptualized according to Bourdieu’s habitus
concept, reflecting the role of unconscious and internalized cultural
signals, proper to low and high socioeconomic status family contexts.
Since families differ by various socioeconomic features, the
hypothesis about possible impact of parents’ socioeconomic status on
their children’s academic motivation interfering with gender
socialization effects is held. The survey, aiming to seize gender
differences in academic motivation and self-recorded improvementoriented
efforts as a result of socialization processes operating in the
families of low and high socioeconomic status, was designed. The
results of Lithuanian higher education students’ survey are presented
and discussed.
Abstract: In this paper a new design of a broadband microwave
power limiter is presented and validated into simulation by using
ADS software (Advanced Design System) from Agilent technologies.
The final circuit is built on microstrip lines by using identical Zero
Bias Schottky diodes. The power limiter is designed by Associating 3
stages Schottky diodes. The obtained simulation results permit to
validate this circuit with a threshold input power level of 0 dBm until
a maximum input power of 30 dBm.
Abstract: In recent years, the compression of date (Phoenix
dactylifera L.) fruit powders (DP) to obtain date tablets (DT) has
been suggested as a promising form of valorization of non
commercial valuable date fruit (DF) varieties. To further improve
and characterize DT, the present study aims to investigate the
influence of the DP particle size and compression force on some
physical properties of DT. The results show that independently of
particle size, the hardness (y) of tablets increases with the increase of
the compression force (x) following a logarithmic law (y = a ln (bx)
where a and b are the constants of model). Further, a full factorial
design (FFD) at two levels, applied to investigate the erosion %,
reveals that the effects of time and particle size are the same in
absolute value and they are beyond the effect of the compression.
Regarding the disintegration time, the obtained results also by means
of a FFD show that the effect of the compression force exceeds 4
times that of the DP particle size. As final stage, the color parameters
in the CIELab system of DT immediately after their obtaining are
differently influenced by the size of the initial powder.
Abstract: Taking the design tolerance into account, this paper
presents a novel efficient approach to generate iso-scallop tool path for
five-axis strip machining with a barrel cutter. The cutter location is
first determined on the scallop surface instead of the design surface,
and then the cutter is adjusted to locate the optimal tool position based
on the differential rotation of the tool axis and satisfies the design
tolerance simultaneously. The machining strip width and error are
calculated with the aid of the grazing curve of the cutter. Based on the
proposed tool positioning algorithm, the tool paths are generated by
keeping the scallop height formed by adjacent tool paths constant. An
example is conducted to confirm the validity of the proposed method.
Abstract: A field experiment was carried out at Arab El-
Awammer Research Station, Agric. Res. Center. Assiut Governorate
during summer seasons of 2013 and 2014. The present study assessed
the effect of cowpea with maize intercropping on yield and its
components. The experiment comprised of three treatments (sole
cowpea, sole maize and cowpea-maize intercrop). The experimental
design was a randomized complete block with four replications.
Results indicated that intercropped maize plants with cowpea,
exhibited greater potentiality and resulted in higher values of most of
the studied criteria viz., plant height, number of ears/plant, number of
rows/ear, number of grains/row, grains weight/ear, 100–grain weight
and straw and grain yields. Fresh and dry forage yields of cowpea
were lower in intercropping with maize than sole. Furthermore, the
combined of the two seasons revealed that the total Land Equivalent
Ratio (LER) between cowpea and maize was 1.65. The Aggressivity
(A) maize was 0.45 and cowpea was -0.45. This showed that maize
was the dominant crop, whereas cowpea was the dominated. The
Competitive Ratio (CR) indicated that maize more competitive than
cowpea, maize was 1.75 and cowpea was 0.57. The Actual Yield
Loss (AYL) maize was 0.05 and cowpea was -0.40. The Monetary
Advantage Index (MAI) was 2360.80.