Abstract: Sewer deposits have been identified as a major cause
of dysfunctions in combined sewer systems regarding sewer
management, which induces different negative consequents resulting
in poor hydraulic conveyance, environmental damages as well as
worker’s health. In order to overcome the problematics of
sedimentation, flushing has been considered as the most operative
and cost-effective way to minimize the sediments impacts and
prevent such challenges. Flushing, by prompting turbulent wave
effects, can modify the bed form depending on the hydraulic
properties and geometrical characteristics of the conduit. So far, the
dynamics of the bed-load during high-flow events in combined sewer
systems as a complex environment is not well understood, mostly due
to lack of measuring devices capable to work in the “hostile” in
combined sewer system correctly. In this regards, a one-episode
flushing issue from an opening gate valve with weir function was
carried out in a trunk sewer in Paris to understand its cleansing
efficiency on the sediments (thickness: 0-30 cm). During more than
1h of flushing within 5 m distance in downstream of this flushing
device, a maximum flowrate and a maximum level of water have
been recorded at 5 m in downstream of the gate as 4.1 m3/s and 2.1
m respectively. This paper is aimed to evaluate the efficiency of this
type of gate for around 1.1 km (from the point -50 m to +1050 m in
downstream from the gate) by (i) determining bed grain-size
distribution and sediments evolution through the sewer channel, as
well as their organic matter content, and (ii) identifying sections that
exhibit more changes in their texture after the flush. For the first one,
two series of sampling were taken from the sewer length and then
analyzed in laboratory, one before flushing and second after, at same
points among the sewer channel. Hence, a non-intrusive sampling
instrument has undertaken to extract the sediments smaller than the
fine gravels. The comparison between sediments texture after the
flush operation and the initial state, revealed the most modified zones
by the flush effect, regarding the sewer invert slope and hydraulic
parameters in the zone up to 400 m from the gate. At this distance,
despite the increase of sediment grain-size rages, D50 (median grainsize)
varies between 0.6 mm and 1.1 mm compared to 0.8 mm and 10
mm before and after flushing, respectively. Overall, regarding the
sewer channel invert slope, results indicate that grains smaller than
sands (< 2 mm) are more transported to downstream along about 400
m from the gate: in average 69% before against 38% after the flush
with more dispersion of grain-sizes distributions. Furthermore, high
effect of the channel bed irregularities on the bed material evolution
has been observed after the flush.
Abstract: This study aims to investigate the mixing behaviors of
deionized (DI) water and carboxymethyl cellulose (CMC) solutions in
C-shaped serpentine micromixers over a wide range of flow
conditions. The flow of CMC solutions exhibits shear-thinning
behaviors. Numerical simulations are performed to investigate the
effects of the mean flow speed, fluid properties and geometry
parameters on flow and mixing in the micromixers with the serpentine
channel of the same overall channel length. From the results, we can
find the following trends. When convection dominates fluid mixing,
the curvature-induced vortices enhance fluid mixing effectively. The
mixing efficiency of a micromixer consisting of semicircular C-shaped
repeating units with a smaller centerline radius is better than that of a
micromixer consisting of major segment repeating units with a larger
centerline radius. The viscosity of DI water is less than the overall
average apparent viscosity of CMC solutions, and so the effect of
curvature-induced vortices on fluid mixing in DI water is larger than
that in CMC solutions for the cases with the same mean flow speed.
Abstract: The disposal and the treatment of sewage sludge is an
expensive and environmentally complex problem. In this work, a
lipopeptide biosurfactant extracted from corn steep liquor was used
as ecofriendly and cost-competitive alternative for the mobilization
and bioremediation of fluorene in sewage sludge. Results have
demonstrated that this biosurfactant has the capability to mobilize
fluorene to the aqueous phase, reducing the amount of fluorene in the
sewage sludge from 484.4 mg/Kg up to 413.7 mg/Kg and 196.0
mg/Kg after 1 and 27 days respectively. Furthermore, once the
fluorene was extracted the lipopeptide biosurfactant contained in the
aqueous phase allowed the biodegradation, up to 40.5% of the initial
concentration of this polycyclic aromatic hydrocarbon.
Abstract: Speaker Identification (SI) is the task of establishing
identity of an individual based on his/her voice characteristics. The SI
task is typically achieved by two-stage signal processing: training and
testing. The training process calculates speaker specific feature
parameters from the speech and generates speaker models
accordingly. In the testing phase, speech samples from unknown
speakers are compared with the models and classified. Even though
performance of speaker identification systems has improved due to
recent advances in speech processing techniques, there is still need of
improvement. In this paper, a Closed-Set Tex-Independent Speaker
Identification System (CISI) based on a Multiple Classifier System
(MCS) is proposed, using Mel Frequency Cepstrum Coefficient
(MFCC) as feature extraction and suitable combination of vector
quantization (VQ) and Gaussian Mixture Model (GMM) together
with Expectation Maximization algorithm (EM) for speaker
modeling. The use of Voice Activity Detector (VAD) with a hybrid
approach based on Short Time Energy (STE) and Statistical
Modeling of Background Noise in the pre-processing step of the
feature extraction yields a better and more robust automatic speaker
identification system. Also investigation of Linde-Buzo-Gray (LBG)
clustering algorithm for initialization of GMM, for estimating the
underlying parameters, in the EM step improved the convergence rate
and systems performance. It also uses relative index as confidence
measures in case of contradiction in identification process by GMM
and VQ as well. Simulation results carried out on voxforge.org
speech database using MATLAB highlight the efficacy of the
proposed method compared to earlier work.
Abstract: Work presented is interested in the characterization of
the quasistatic mechanical properties and in fatigue of a composite
laminated in jute/epoxy. The natural fibers offer promising prospects
thanks to their interesting specific properties, because of their low
density, but also with their bio-deterioration. Several scientific
studies highlighted the good mechanical resistance of the vegetable
fiber composites reinforced, even after several recycling. Because of
the environmental standards that become increasingly severe, one
attends the emergence of eco-materials at the base of natural fibers
such as flax, bamboo, hemp, sisal, jute. The fatigue tests on
elementary vegetable fibers show an increase of about 60% of the
rigidity of elementary fibers of hemp subjected to cyclic loadings. In
this study, the test-tubes manufactured by the method infusion have
sequences of stacking of 0/90° and ± 45° for the shearing and tensile
tests. The quasistatic tests reveal a variability of the mechanical
properties of about 8%. The tensile fatigue tests were carried out for
levels of constraints equivalent to half of the ultimate values of the
composite. Once the fatigue tests carried out for well-defined values
of cycles, a series of static tests of traction type highlights the
influence of the number of cycles on the quasi-static mechanical
behavior of the laminate jute/epoxy.
Abstract: In this paper, we report the development of the device
for diagnostics of cardiovascular system state and associated
automated workstation for large-scale medical measurement data
collection and analysis. It was shown that optimal design for the
monitoring device is wristband as it represents engineering trade-off
between accuracy and usability. Monitoring device is based on the
infrared reflective photoplethysmographic sensor, which allows
collecting multiple physiological parameters, such as heart rate and
pulsing wave characteristics. Developed device uses BLE interface
for medical and supplementary data transmission to the coupled
mobile phone, which processes it and send it to the doctor's
automated workstation. Results of this experimental model
approbation confirmed the applicability of the proposed approach.
Abstract: Indonesia has experienced annual forest fires that have
rapidly destroyed and degraded its forests. Fires in the peat swamp
forests of Riau Province, have set the stage for problems to worsen,
this being the ecosystem most prone to fires (which are also the most
difficult, to extinguish). Despite various efforts to curb deforestation,
and forest degradation processes, severe forest fires are still
occurring. To find an effective solution, the basic causes of the
problems must be identified. It is therefore critical to have an indepth
understanding of the underlying causal factors that have
contributed to deforestation and forest degradation as a whole, in
order to attain reductions in their rates. An assessment of the drivers of deforestation and forest
degradation was carried out, in order to design and implement
measures that could slow these destructive processes. Research was
conducted in Giam Siak Kecil–Bukit Batu Biosphere Reserve
(GSKBB BR), in the Riau Province of Sumatera, Indonesia. A
biosphere reserve was selected as the study site because such reserves
aim to reconcile conservation with sustainable development. A
biosphere reserve should promote a range of local human activities,
together with development values that are in line spatially and
economically with the area conservation values, through use of a
zoning system. Moreover, GSKBB BR is an area with vast peatlands,
and is experiencing forest fires annually. Various factors were
analysed to assess the drivers of deforestation and forest degradation
in GSKBB BR; data were collected from focus group discussions
with stakeholders, key informant interviews with key stakeholders,
field observation and a literature review. Landsat satellite imagery was used to map forest-cover changes
for various periods. Analysis of landsat images, taken during the
period 2010-2014, revealed that within the non-protected area of core
zone, there was a trend towards decreasing peat swamp forest areas,
increasing land clearance, and increasing areas of community oilpalm
and rubber plantations. Fire was used for land clearing and most
of the forest fires occurred in the most populous area (the transition
area). The study found a relationship between the deforested/
degraded areas, and certain distance variables, i.e. distance from
roads, villages and the borders between the core area and the buffer
zone. The further the distance from the core area of the reserve, the
higher was the degree of deforestation and forest degradation. Research findings suggested that agricultural expansion may be
the direct cause of deforestation and forest degradation in the reserve,
whereas socio-economic factors were the underlying driver of forest
cover changes; such factors consisting of a combination of sociocultural,
infrastructural, technological, institutional (policy and governance), demographic (population pressure) and economic
(market demand) considerations. These findings indicated that local
factors/problems were the critical causes of deforestation and
degradation in GSKBB BR. This research therefore concluded that
reductions in deforestation and forest degradation in GSKBB BR
could be achieved through ‘local actor’-tailored approaches such as
community empowerment.
Abstract: Constructed Wetland (CW) is a reasonable method to
treat wastewater. Current study was carried out to co-treat landfill
leachate and domestic wastewater using a CW system. Typha
domingensis was transplanted to CW, which encloses two substrate
layers of adsorbents named ZELIAC and zeolite. Response surface
methodology and central composite design were employed to
evaluate experimental data. Contact time (h) and leachate-towastewater
mixing ratio (%; v/v) were selected as independent
factors. Phenols and manganese removal were selected as dependent
responses. At optimum contact time (48.7 h) and leachate-towastewater
mixing ratio (20.0%), removal efficiencies of phenols and
manganese removal efficiencies were 90.5%, and 89.4%,
respectively.
Abstract: The development of transport systems has negative
impacts on the environment although it has beneficial effects on
society. The car policy caused many problems such as: - the
spectacular growth of fuel consumption hence the very vast increase
in urban pollution, traffic congestion in certain places and at certain
times, the increase in the number of accidents. The exhaust emissions
from cars and weather conditions are the main factors that determine
the level of pollution in urban atmosphere. These conditions lead to
the phenomenon of heat transfer and radiation occurring between the
air and the soil surface of any town. These exchanges give rise, in
urban areas, to the effects of heat islands that correspond to the
appearance of excess air temperature between the city and its
surrounding space. In this object, we perform a numerical simulation
of the plume generated by the cars exhaust gases and show that these
gases form a screening effect above the urban city which cause the
heat island in the presence of wind flow. This study allows us: 1. To
understand the different mechanisms of interactions between these
phenomena.2. To consider appropriate technical solutions to mitigate
the effects of the heat island.
Abstract: DNA analysis has been widely accepted as providing
valuable evidence concerning the identity of the source of biological
traces. Our work has showed that DNA samples can survive on
cartridges even after firing. The study also raised the possibility of
determining other information such as the age of the donor. Such
information may be invaluable in certain cases where spent cartridges
from automatic weapons are left behind at the scene of a crime. In
spite of the nature of touch evidence and exposure to high chamber
temperatures during shooting, we were still capable to retrieve
enough DNA for profile typing. In order to estimate age of
contributor, DNA methylation levels were analyzed using EpiTect
system for retrieved DNA. However, results were not conclusive, due
to low amount of input DNA.
Abstract: In the present study, the properties of Al-Al2O3
nanocomposite hollow sphere structures were investigated. For this
reason, the Al-based nanocomposite hollow spheres with different
amounts of nano-alumina reinforcement (0-10wt %) and different
ratio of thickness to diameter (t/D: 0.06-0.3) were prepared via a
powder metallurgy method. Then, the effect of mentioned parameters
was studied on physical and quasi static mechanical properties of
their related prepared structures (open/closed cell) such as density,
hardness, strength, and energy absorption. It was found that, as the
t/D ratio increases the relative density, compressive strength and
energy absorption increase. The highest values of strength and energy
absorption were obtained from the specimen with 5 wt. % of
nanoparticle reinforcement, t/D of 0.3 (t=1 mm, D=400μm) as 22.88
MPa and 13.24 MJ/m3, respectively. The moderate specific strength
of prepared composites in the present study showed the good
consistency with the properties of others low carbon steel composite
with similar structure.
Abstract: In this paper comprehensive studies have been carried
out for the design optimization of a waste heat recovery system for
effectively utilizing the domestic air conditioner heat energy for
producing hot water. Numerical studies have been carried for the
geometry optimization of a waste heat recovery system for domestic
air conditioners. Numerical computations have been carried out using
a validated 2d pressure based, unsteady, 2nd-order implicit, SST k-ω
turbulence model. In the numerical study, a fully implicit finite
volume scheme of the compressible, Reynolds-Averaged, Navier-
Stokes equations is employed. At identical inflow and boundary
conditions various geometries were tried and effort has been taken for
proposing the best design criteria. Several combinations of pipe line
shapes viz., straight and spiral with different number of coils for the
radiator have been attempted and accordingly the design criteria has
been proposed for the waste heat recovery system design. We have
concluded that, within the given envelope, the geometry optimization
is a meaningful objective for getting better performance of waste heat
recovery system for air conditioners.
Abstract: Spacer grid assembly supporting the nuclear fuel rods
is an important concern in the design of structural components of a
Pressurized Water Reactor (PWR). The spacer grid is composed by
springs and dimples which are formed from a strip sheet by means of
blanking and stamping processes. In this paper, the blanking process
and tooling parameters are evaluated by means of a 2D plane-strain
finite element model in order to evaluate the punch load and quality
of the sheared edges of Inconel 718 strips used for nuclear spacer
grids. A 3D finite element model is also proposed to predict the
tooling loads resulting from the stamping process of a preformed
Inconel 718 strip and to analyse the residual stress effects upon the
spring and dimple design geometries of a nuclear spacer grid.
Abstract: Chalcopyrite (CuFeS2) is the most common primary
mineral used for the commercial production of copper. The low
dissolution efficiency of chalcopyrite in sulfate media has prevented
an efficient industrial leaching of this mineral in sulfate media. Ferric
ions, bacteria, oxygen and other oxidants have been used as oxidizing
agents in the leaching of chalcopyrite in sulfate and chloride media
under atmospheric or pressure leaching conditions. Two leaching
methods were studied to evaluate chalcopyrite (CuFeS2) dissolution
in acid media. First, the conventional oxidative acid leaching method
was carried out using sulfuric acid (H2SO4) and potassium
dichromate (K2Cr2O7) as oxidant at atmospheric pressure. Second,
microwave-assisted acid leaching was performed using the
microwave accelerated reaction system (MARS) for same reaction
media. Parameters affecting the copper extraction such as leaching
time, leaching temperature, concentration of H2SO4 and
concentration of K2Cr2O7 were investigated. The results of
conventional acid leaching experiments were compared to the
microwave leaching method. It was found that the copper extraction
obtained under high temperature and high concentrations of oxidant
with microwave leaching is higher than those obtained
conventionally. 81% copper extraction was obtained by the
conventional oxidative acid leaching method in 180 min, with the
concentration of 0.3 mol/L K2Cr2O7 in 0.5M H2SO4 at 50 ºC, while
93.5% copper extraction was obtained in 60 min with microwave
leaching method under same conditions.
Abstract: Nowadays, several research studies point up that an
active lifestyle is essential for physical and mental health benefits.
Mobile phones have greatly influenced people’s habits and attitudes
also in the way they exercise. Our research work is mainly focused on
investigating how to exploit mobile technologies to favour people’s
exertion experience. To this end, we developed an exertion framework
users can exploit through a real world mobile application, called
EverywhereSport Run (EWRun), designed to act as a virtual personal
trainer to support runners during their trainings. In this work, inspired
by both previous findings in the field of interaction design for people
with visual impairments, feedback gathered from real users of our
framework, and positive results obtained from two experimentations,
we present some new interaction facilities we designed to enhance
the interaction experience during a training. The positive obtained
results helped us to derive some interaction design recommendations
we believe will be a valid support for designers of future mobile
systems conceived to be used in circumstances where there are limited
possibilities of interaction.
Abstract: The development of electric vehicle batteries have
resulted in very high energy density lithium-ion batteries. However,
this progress is accompanied by the risk of thermal runaway, which
can result in serious accidents. Heat pipes are heat exchangers that
are suitable to be applied in electric vehicle battery thermal
management for their lightweight, compact size and do not require
external power supply. This paper aims to examine experimentally a
Flat Plate Loop Heat Pipe (FPLHP) performance as a heat exchanger
in thermal management system of lithium-ion battery for electric
vehicle application. The heat generation of the battery was simulated
using a cartridge heater. Stainless steel screen mesh was used as the
capillary wick. Distilled water, alcohol and acetone were used as
working fluids with a filling ratio of 60%. It was found that acetone
gives the best performance that produces thermal resistance of 0.22
W/°C with 50°C evaporator temperature at heat flux load of 1.61
W/cm2.
Abstract: Phonocardiography is important in appraisal of
congenital heart disease and pulmonary hypertension as it reflects the
duration of right ventricular systoles. The systolic murmur in patients
with intra-cardiac shunt decreases as pulmonary hypertension
develops and may eventually disappear completely as the pulmonary
pressure reaches systemic level. Phonocardiography and auscultation
are non-invasive, low-cost, and accurate methods to assess heart
disease. In this work an objective signal processing tool to extract
information from phonocardiography signal using Wavelet is
proposed to classify the murmur as normal or abnormal. Since the
feature vector is large, a Binary Particle Swarm Optimization (PSO)
with mutation for feature selection is proposed. The extracted
features improve the classification accuracy and were tested across
various classifiers including Naïve Bayes, kNN, C4.5, and SVM.
Abstract: ANDASA is a knowledge management platform for
the capitalization of knowledge and cultural assets for the artistic and
cultural sectors. It was built based on the priorities expressed by the
participating artists. Through mapping artistic activities and
specificities, it enables to highlight various aspects of the artistic
research and production. Such instrument will contribute to create
networks and partnerships, as it enables to evidentiate who does
what, in what field, using which methodology. The platform is
accessible to network participants and to the general public.
Abstract: In order to study the effect of different levels of triple
super phosphate chemical fertilizer and biological phosphate fertilizer
(fertile 2) on some morphological traits of corn this research was
carried out in Ahvaz in 2002 as a factorial experiment in randomized
complete block design with 4 replications). The experiment included
two factors: first, biological phosphate fertilizer (fertile 2) at three
levels of 0, 100, 200 g/ha; second, triple super phosphate chemical
fertilizer at three levels of 0, 60, 90 kg/ha of pure phosphorus (P2O5).
The obtained results indicated that fertilizer treatments had a
significant effect on some morphological traits at 1% probability
level. In this regard, P2B2 treatment (100 g/ha biological phosphate
fertilizer (fertile 2) and 60 kg/ha triple super phosphate fertilizer) had
the greatest plant height, stem diameter, number of leaves and ear
length. It seems that in Ahvaz weather conditions, decrease of
consumption of triple superphosphate chemical fertilizer to less than
a half along with the consumption of biological phosphate fertilizer
(fertile 2) is highly important in order to achieve optimal results.
Therefore, it can be concluded that biological fertilizers can be used
as a suitable substitute for some of the chemical fertilizers in
sustainable agricultural systems.
Abstract: An experimental investigation is carried out to
establish the performance characteristics of a compression ignition
engine while using cerium oxide nanoparticles as additive in neat
diesel and diesel-biodiesel blends. In the first phase of the
experiments, stability of neat diesel and diesel-biodiesel fuel blends
with the addition of cerium oxide nanoparticles is analyzed. After
series of experiments, it is found that the blends subjected to high
speed blending followed by ultrasonic bath stabilization improves the
stability. In the second phase, performance characteristics are studied
using the stable fuel blends in a single cylinder four stroke engine
coupled with an electrical dynamometer and a data acquisition
system. The cerium oxide acts as an oxygen donating catalyst and
provides oxygen for combustion. The activation energy of cerium
oxide acts to burn off carbon deposits within the engine cylinder at
the wall temperature and prevents the deposition of non-polar
compounds on the cylinder wall results reduction in HC emissions.
The tests revealed that cerium oxide nanoparticles can be used as
additive in diesel and diesel-biodiesel blends to improve complete
combustion of the fuel significantly.