Abstract: The paper provides biomasses characteristics by
proximate analysis (volatile matter, fixed carbon and ash) and
ultimate analysis (carbon, hydrogen, nitrogen and oxygen) for the
prediction of the heating value equations. The heating value
estimation of various biomasses can be used as an energy evaluation.
Thirteen types of biomass were studied. Proximate analysis was
investigated by mass loss method and infrared moisture analyzer.
Ultimate analysis was analyzed by CHNO analyzer. The heating
values varied from 15 to 22.4MJ kg-1. Correlations of the calculated
heating value with proximate and ultimate analyses were undertaken
using multiple regression analysis and summarized into three and two
equations, respectively. Correlations based on proximate analysis
illustrated that deviation of calculated heating values from
experimental heating values was higher than the correlations based
on ultimate analysis.
Abstract: In this paper, we discuss convergence of the extrapolated iterative methods for linear systems with the coefficient matrices are singular H-matrices. And we present the sufficient and necessary conditions for convergence of the extrapolated iterative methods. Moreover, we apply the results to the GMAOR methods. Finally, we give one numerical example.
Abstract: The paper presents the virtual model of the active
suspension system used for improving the dynamic behavior of a
motor vehicle. The study is focused on the design of the control
system, the purpose being to minimize the effect of the road
disturbances (which are considered as perturbations for the control
system). The analysis is performed for a quarter-car model, which
corresponds to the suspension system of the front wheel, by using the
DFC (Design for Control) software solution EASY5 (Engineering
Analysis Systems) of MSC Software. The controller, which is a PIDbased
device, is designed through a parametric optimization with the
Matrix Algebra Tool (MAT), considering the gain factors as design
variables, while the design objective is to minimize the overshoot of
the indicial response.
Abstract: The main objective of our study is to collect data
about the profile of the asthmatic patients in Assam and thereby have
a comprehensive knowledge of the factors influencing the asthmatic
patients of the state and their medication pattern. We developed a
search strategy to find any publication about the community based
survey asthma related and used. These to search the MEDLINE
(1996 to current literature) CINAHL DOAJ pubmed databases using
the key phrases, Asthma, Respiratory disorders, Drug therapy of
Asthma, database decision support system and asthma. The
appropriate literature was printed out from the online source and
library (Journal) source. The study was conducted through a set of
structured and non-structured questionnaires targeted on the
asthmatic patients belonging to the rural and urban areas of Assam,
during the month of Dec 2006 to July 2007, 138 cases were studied
in Gauwathi Medical College & Hospital located in Bhangagarh,
Assam in India. The demographic characteristics a factor in 138
patients with asthma with allergic rhinitis (cases) gives the detail
profile of asthmatic patient-s distribution of Assam as classified on
the basis of age and sex. It is evident from the study that male
populations (66%) are more prone to asthma as compared to the
females (34%).Another striking features that emerged from this
survey is the maximum prevalence of asthma in the age group of 20-
30 years followed by infants belonging to the age group of 7 (0.05%)
0-10years among both male and female populations of Assam. The
high incidence of asthma in the age group of 20-30 years may
probably be due to the allergy arising out of sudden exposure to dust
and pollen which the children face while playing and going to the
school. The rural females in the age group of 30-40 years are more
prone to asthma than urban females in the same age group may be
due to sex differentiation among the tribal population of the state.
Pharmacists should educate the asthmatics how to use inhalers
considering growing menace of asthma in the state. Safer drugs
should be produced in the form of aerosol so that easy administration
by the asthmatic patients and physicians of the state is possible for
curing asthma. The health centers should be more equipped with the
medicines to cure asthma in the state like Assam.
Abstract: The emergence of person-centred discourse based
around notions of 'personal development planning- and 'work'life
balance' has taken hold in education and the workplace in recent
years. This paper examines this discourse with regard to recent
developments in higher education as well as the inter-related issue of
work-life balance in occupational careers. In both cases there have
been national and trans-national policy initiatives directed towards
improving both personal opportunities and competitive advantage in
a global knowledge-based economy. However, despite an increasing
concern with looking outward at this globalised educational and
employment marketplace, there is something of a paradox in
encouraging people to look inward at themselves in order to become
more self-determined. This apparent paradox is considered from a
discourse analytic perspective in terms of the ideological effects of an
increasing concern with the personal world. Specifically, it is argued
that there are tensions that emerge from a concern with an innerdirected
process of self-reflection that dissolve any engagement with
wider political issues that impact upon educational and career
development.
Abstract: The aim of this paper is to investigate the effect of
mean size of industry on survival of new firms in East-Azarbaijan
province through 1981-2006 using hazard function. So the effect of
two variables including mean employment of industry and mean
capital of industry are investigated on firm's survival. The Industry &
Mine Ministry database has used for data gathering and the data are
analyzed using the semi-parametric cox regression model. The results
of this study shows that there is a meaningful negative relationship
between mean capital of industry and firm's survival, but the mean
employment of industry has no meaningful effect on survival of new
firms.
Abstract: Due to important issues, such as deadlock, starvation,
communication, non-deterministic behavior and synchronization,
concurrent systems are very complex, sensitive, and error-prone.
Thus ensuring reliability and accuracy of these systems is very
essential. Therefore, there has been a big interest in the formal
specification of concurrent programs in recent years. Nevertheless,
some features of concurrent systems, such as dynamic process
creation, scheduling and starvation have not been specified formally
yet. Also, some other features have been specified partially and/or
have been described using a combination of several different
formalisms and methods whose integration needs too much effort. In
other words, a comprehensive and integrated specification that could
cover all aspects of concurrent systems has not been provided yet.
Thus, this paper makes two major contributions: firstly, it provides a
comprehensive formal framework to specify all well-known features
of concurrent systems. Secondly, it provides an integrated
specification of these features by using just a single formal notation,
i.e., the Z language.
Abstract: The present paper deals with the experimental and
computational study of axial collapse of the aluminum metallic shells
having combined tube-frusta geometry between two parallel plates.
Shells were having bottom two third lengths as frusta and remaining
top one third lengths as tube. Shells were compressed to recognize
their modes of collapse and associated energy absorption capability.
An axisymmetric Finite Element computational model of collapse
process is presented and analysed, using a non-linear FE code
FORGE2. Six noded isoparametric triangular elements were used to
discretize the deforming shell. The material of the shells was
idealized as rigid visco-plastic. To validate the computational model
experimental and computed results of the deformed shapes and their
corresponding load-compression and energy-compression curves
were compared. With the help of the obtained results progress of the
axisymmetric mode of collapse has been presented, analysed and
discussed.
Abstract: The problem of agricultural-soil pollution is closely
linked to the production of ecologically pure foodstuffs and to human health. An important task, therefore, is to rehabilitate agricultural
soils with the help of state-of-the-art biotechnologies, based on the use of metal-accumulating plants. In this work, on the basis of
literature data and the results of prior research from this laboratory, plants were selected for which the growing technology is well
developed and which are widespread locally: sugar sorghum (Sorghum saccharatum), sudangrass (Sorghum sudanense (Piper.)
Stapf.), and sunflower (Helianthus annuus L.). I report on laboratory
experiments designed to study the influence of synthetic indole-3-
acetic acid and the extracellular indole-3-acetic acid released by the
plant-growth-promoting rhizobacterium Azospirillum brasilense Sp245 on growth of and arsenic accumulation by these plants.
Abstract: Text categorization is the problem of classifying text
documents into a set of predefined classes. After a preprocessing
step, the documents are typically represented as large sparse vectors.
When training classifiers on large collections of documents, both the
time and memory restrictions can be quite prohibitive. This justifies
the application of feature selection methods to reduce the
dimensionality of the document-representation vector. In this paper,
three feature selection methods are evaluated: Random Selection,
Information Gain (IG) and Support Vector Machine feature selection
(called SVM_FS). We show that the best results were obtained with
SVM_FS method for a relatively small dimension of the feature
vector. Also we present a novel method to better correlate SVM
kernel-s parameters (Polynomial or Gaussian kernel).
Abstract: The present study aimed to investigate whether
chlorophyll meter readings (SPAD) can be used as criterion of singleplant
selection in maize breeding. Experimentation was performed at
the ultra-low density of 0.74 plants/m2 in order the potential yield per
plant to be fully expressed. R-31 honeycomb experiments were
conducted in three different areas in Greece (Thessaloniki, Giannitsa
and Florina) using 30 inbred lines at well-watered and water-stressed
conditions during the 2012 growing season. The chlorophyll meter
readings had higher rates at dry conditions, except location of
Giannitsa where differences were not significant. Genotypes of
highest chlorophyll meter readings were consistent across areas,
emphasizing on the character’s stability. A positive correlation
between the chlorophyll meter readings and grain yield was
strengthening over time and culminated at the physiological maturity
stage. There was a clear sign that the chlorophyll meter readings has
the potential to be used for the selection of stress-adaptive genotypes
and may permit modern maize to be grown at wider range of
environments addressing the climate change scenarios.
Abstract: The main purpose of this research was to study how to communicate the identity of the Bangpoo, Samu tPrakan province for ecotourism. The qualitative data was collected through studying related materials, exploring the area, in-depth interviews with three groups of people: three directly responsible officers who were key informants of the district, twenty foreign tourists and five Thai tourist guides. A content analysis was used to analyze the qualitative data. The two main findings of the study were as follows:
The identity of Bangpoo, Samut Prakan province. This establishment was near the Mouth of the Gulf of Thailand for normal people and tourists, consisting of rest accommodations. There are restaurants where food and drinks are served, rich mangrove forests, Banpoo seaside resort and mangrove trees. Bangpoo seaside resort is characterized by muddy beacheswhere the greatest number of seagulls can be seen from March to May each year.
The communication of the identity of Bangpoo, Samut Prakan province which the researcher could find and design to present in English materials can be summed up in 3 items: 1) The history of Bangpoo, Samut Prakan province 2) The Learning center of Ecotourism: Seagulls and Mangrove forest 3) How to keep Banpoo, Samut Prakran province for ecotourism.
Abstract: Surface roughness (Ra) is one of the most important requirements in machining process. In order to obtain better surface roughness, the proper setting of cutting parameters is crucial before the process take place. This research presents the development of mathematical model for surface roughness prediction before milling process in order to evaluate the fitness of machining parameters; spindle speed, feed rate and depth of cut. 84 samples were run in this study by using FANUC CNC Milling α-Τ14ιE. Those samples were randomly divided into two data sets- the training sets (m=60) and testing sets(m=24). ANOVA analysis showed that at least one of the population regression coefficients was not zero. Multiple Regression Method was used to determine the correlation between a criterion variable and a combination of predictor variables. It was established that the surface roughness is most influenced by the feed rate. By using Multiple Regression Method equation, the average percentage deviation of the testing set was 9.8% and 9.7% for training data set. This showed that the statistical model could predict the surface roughness with about 90.2% accuracy of the testing data set and 90.3% accuracy of the training data set.
Abstract: On a such wide-area environment as a Grid, data
placement is an important aspect of distributed database systems. In
this paper, we address the problem of initial placement of database
no-replicated fragments in Grid architecture. We propose a graph
based approach that considers resource restrictions. The goal is to
optimize the use of computing, storage and communication
resources. The proposed approach is developed in two phases: in the
first phase, we perform fragment grouping using knowledge about
fragments dependency and, in the second phase, we determine an
efficient placement of the fragment groups on the Grid. We also
show, via experimental analysis that our approach gives solutions
that are close to being optimal for different databases and Grid
configurations.
Abstract: Mechanical buckling analysis of rectangular plates
with central circular cutout is performed in this paper. The finiteelement
method is used to study the effects of plate-support
conditions, aspect ratio, and hole size on the mechanical buckling
strength of the perforated plates subjected to linearly varying loading.
Results show that increasing the hole size does not necessarily reduce
the mechanical buckling strength of the perforated plates. It is also
concluded that the clamped boundary condition increases the
mechanical buckling strength of the perforated plates more than the
simply-supported boundary condition and the free boundary
conditions enhance the mechanical buckling strength of the
perforated plates more effectively than the fixed boundary conditions.
Furthermore, for the bending cases, the critical buckling load of
perforated plates with free edges is less than perforated plates with
fixed edges.
Abstract: Key management represents a major and the most
sensitive part of cryptographic systems. It includes key generation,
key distribution, key storage, and key deletion. It is also considered
the hardest part of cryptography. Designing secure cryptographic
algorithms is hard, and keeping the keys secret is much harder.
Cryptanalysts usually attack both symmetric and public key
cryptosystems through their key management. We introduce a
protocol to exchange cipher keys over insecure communication
channel. This protocol is based on public key cryptosystem,
especially elliptic curve cryptosystem. Meanwhile, it tests the cipher
keys and selects only the good keys and rejects the weak one.
Abstract: Artificial Neural Network (ANN)s are best suited for
prediction and optimization problems. Trained ANNs have found
wide spread acceptance in several antenna design systems. Four
parameters namely antenna radiation resistance, loss resistance, efficiency,
and inductance can be used to design an antenna layout though
there are several other parameters available. An ANN can be trained
to provide the best and worst case precisions of an antenna design
problem defined by these four parameters. This work describes the
use of an ANN to generate the four mentioned parameters for a loop
antenna for the specified frequency range. It also provides insights
to the prediction of best and worst-case design problems observed
in applications and thereby formulate a model for physical layout
design of a loop antenna.
Abstract: A novel low-cost impedance control structure is
proposed for monitoring the contact force between end-effector and
environment without installing an expensive force/torque sensor.
Theoretically, the end-effector contact force can be estimated from the
superposition of each joint control torque. There have a nonlinear
matrix mapping function between each joint motor control input and
end-effector actuating force/torques vector. This new force control
structure can be implemented based on this estimated mapping matrix.
First, the robot end-effector is manipulated to specified positions, then
the force controller is actuated based on the hall sensor current
feedback of each joint motor. The model-free fuzzy sliding mode
control (FSMC) strategy is employed to design the position and force
controllers, respectively. All the hardware circuits and software
control programs are designed on an Altera Nios II embedded
development kit to constitute an embedded system structure for a
retrofitted Mitsubishi 5 DOF robot. Experimental results show that PI
and FSMC force control algorithms can achieve reasonable contact
force monitoring objective based on this hardware control structure.
Abstract: When it comes to last, it is regarded as the critical
foundation of shoe design and development. A computer aided
methodology for various last form designs is proposed in this study.
The reverse engineering is mainly applied to the process of scanning
for the last form. Then with the minimum energy for revision of
surface continuity, the surface reconstruction of last is rebuilt by the
feature curves of the scanned last. When the surface reconstruction of
last is completed, the weighted arithmetic mean method is applied to
the computation on the shape morphing for the control mesh of last,
thus 3D last form of different sizes is generated from its original form
feature with functions remained. In the end, the result of this study is
applied to an application for 3D last reconstruction system. The
practicability of the proposed methodology is verified through later
case studies.
Abstract: In current global economics the application of Business Continuity Management is the prerequisite for sustainable competitive advantage in an organization. Business Continuity Management is a managerial which identifies the potential impact of losses in an organization. The aim of this paper is to identify and critically evaluate the relative advantages and disadvantages of deploying Business Continuity Management in an organization on the basis of seven criteria. The strongest advantage of Business Continuity Management is in its capacity to identify a crisis situation and help the organization to flexibly and also to keep the critical knowledge within the organization. By contrast the main disadvantage is that establishing Business Continuity Management in an organization is time-consuming and its implementation as an integral part of the organizational culture present significant difficulties.