Abstract: For collecting data from all sensor nodes, some
changes in Dynamic Source Routing (DSR) protocol is proposed. At
each hop level, route-ranking technique is used for distributing
packets to different selected routes dynamically. For calculating rank
of a route, different parameters like: delay, residual energy and
probability of packet loss are used. A hybrid topology of
DMPR(Disjoint Multi Path Routing) and MMPR(Meshed Multi Path
Routing) is formed, where braided topology is used in different
faulty zones of network. For reducing energy consumption, variant
transmission ranges is used instead of fixed transmission range. For
reducing number of packet drop, a fuzzy logic inference scheme is
used to insert different types of delays dynamically. A rule based
system infers membership function strength which is used to
calculate the final delay amount to be inserted into each of the node
at different clusters.
In braided path, a proposed 'Dual Line ACK Link'scheme is
proposed for sending ACK signal from a damaged node or link to a
parent node to ensure that any error in link or any node-failure
message may not be lost anyway. This paper tries to design the
theoretical aspects of a model which may be applied for collecting
data from any large hanging iron structure with the help of wireless
sensor network. But analyzing these data is the subject of material
science and civil structural construction technology, that part is out
of scope of this paper.
Abstract: The present work is concerned with the free
convective two dimensional flow and heat transfer, in isotropic fluid
filled porous rectangular enclosure with differentially heated walls for
steady state incompressible flow have been investigated for non-
Darcy flow model. Effects of Darcy number (0.0001 £Da£ 10),
Rayleigh number (10 £Ra£ 5000), and aspect ratio (0.25 £AR£ 4), for
a range of porosity (0.4 £e£ 0.9) with and without moving lower wall
have been studied. The cavity was insulated at the lower and upper
surfaces. The right and left heated surfaces allows convective
transport through the porous medium, generating a thermal
stratification and flow circulations. It was found that the Darcy
number, Rayleigh number, aspect ratio, and porosity considerably
influenced characteristics of flow and heat transfer mechanisms. The
results obtained are discussed in terms of the Nusselt number,
vectors, contours, and isotherms.
Abstract: Considering the serious health hazards of air pollutants from automobiles, the present study was aimed to estimate the genotoxic/tumor inducing potential of three soil samples collected from junctions of Bus stand (BS), Crystal (CT) and Railway station (RS) of Amritsar, Punjab (India) using Allium cepa root chromosomal aberration assay (AlRCAA) and potato disc tumor assay (PDTA). The genotoxic potential in AlRCAA was 41.27% and 41.26% for BS; 37.89% and 43.38% for RS and 33.76% and 37.83% for CT during in situ and root dip treatments, respectively. The maximum number of tumors were induced in RS sample (64) followed by BS (21) and CT (9) during PDTA. The physicochemical parameters of soil sample were also studied and the concentration of lead was found to be 95.21 mg/Kg in RS, 35.30 mg/Kg in BS and 24.59 mg/Kg in CT samples.
Abstract: The use of Quantum dots is a promising emerging
Technology for implementing digital system at the nano level. It is
effecient for attractive features such as faster speed , smaller size and
low power consumption than transistor technology. In this paper,
various Combinational and sequential logical structures - HALF
ADDER, SR Latch and Flip-Flop, D Flip-Flop preceding NAND,
NOR, XOR,XNOR are discussed based on QCA design, with
comparatively less number of cells and area. By applying these
layouts, the hardware requirements for a QCA design can be reduced.
These structures are designed and simulated using QCA Designer
Tool. By taking full advantage of the unique features of this
technology, we are able to create complete circuits on a single layer
of QCA. Such Devices are expected to function with ultra low
power Consumption and very high speeds.
Abstract: Plant tissue culture is an important in vitro technology applied for agricultural and industrial production. A sterile condition of culture medium is one of the main aspects. The alternative technique for medium sterilization to replace autoclaving was carried out. For sterilization of plant tissue culture medium without autoclaving, ten commercial pure essential oils and 5 disinfectants were tested. Each essential oil or disinfectant was added to a 20-mL Murashige and Skoog (MS) medium before medium was solidified in a 120-mL container, kept for 2 weeks before evaluating sterile conditions. Treated media, supplemented with essential oils or disinfectants, were compared to control medium, autoclaved at 121 degree Celsius for 15 min. Sterile conditions of MS medium were found 100% from betel oil or clove oil (18 mL/20 mL medium), cinnamon oil (36 mL/20 mL medium), lavender oil or holy basil oil (108 mL/20 mL medium), and lemon oil or tea tree oil or turmeric oil (252 mL/20 mL medium), compared to 100% sterile condition from autoclaved medium. For disinfectants, 2% iodine + 2.4% potassium iodide, 2% merbromine solution, 10% povidone-iodine, 6% sodium hypochlorite or 0.1% thimerosal at 36 mL/20 mL medium provided 100% sterile conditions. Furthermore, growth of new shoots from chrysanthemum node explants on treated media (fresh weight, shoot length, root length and number of node) were also reported and discussed in the comparison of those on autoclaved medium.
Abstract: The InAlGaN alloy has only recently began receiving
serious attention into its growth and application. High quality InGaN
films have led to the development of light emitting diodes (LEDs) and
blue laser diodes (LDs). The quaternary InAlGaN however, represents
a more versatile material since the bandgap and lattice constant can be
independently varied. We report an ultraviolet (UV) quaternary
InAlGaN multi-quantum wells (MQWs) LD study by using the
simulation program of Integrated System Engineering (ISE TCAD).
Advanced physical models of semiconductor properties were used in
order to obtain an optimized structure. The device performance which
is affected by piezoelectric and thermal effects was studied via
drift-diffusion model for carrier transport, optical gain and loss. The
optical performance of the UV LD with different numbers of quantum
wells was numerically investigated. The main peak of the emission
wavelength for double quantum wells (DQWs) was shifted from 358
to 355.8 nm when the forward current was increased. Preliminary
simulated results indicated that better output performance and lower
threshold current could be obtained when the quantum number is four,
with output power of 130 mW and threshold current of 140 mA.
Abstract: In the context of spectrum surveillance, a new method
to recover the code of spread spectrum signal is presented, while the
receiver has no knowledge of the transmitter-s spreading sequence. In
our previous paper, we used Genetic algorithm (GA), to recover
spreading code. Although genetic algorithms (GAs) are well known
for their robustness in solving complex optimization problems, but
nonetheless, by increasing the length of the code, we will often lead
to an unacceptable slow convergence speed. To solve this problem we
introduce Particle Swarm Optimization (PSO) into code estimation in
spread spectrum communication system. In searching process for
code estimation, the PSO algorithm has the merits of rapid
convergence to the global optimum, without being trapped in local
suboptimum, and good robustness to noise. In this paper we describe
how to implement PSO as a component of a searching algorithm in
code estimation. Swarm intelligence boasts a number of advantages
due to the use of mobile agents. Some of them are: Scalability, Fault
tolerance, Adaptation, Speed, Modularity, Autonomy, and
Parallelism. These properties make swarm intelligence very attractive
for spread spectrum code estimation. They also make swarm
intelligence suitable for a variety of other kinds of channels. Our
results compare between swarm-based algorithms and Genetic
algorithms, and also show PSO algorithm performance in code
estimation process.
Abstract: The pollutant removal efficiency of the Intermittently
Decanted Extended Aeration (IDEA) wastewater treatment system at
Curtin University Sarawak Campus, and conventional activated
sludge wastewater treatment system at a local resort, Resort A, is
monitored. The influent and effluent characteristics are tested during
wet and dry weather conditions, and peak and off peak periods. For
the wastewater treatment systems at Curtin Sarawak and Resort A,
during dry weather and peak season, it was found that the BOD5
concentration in the influent is 121.7mg/L and 80.0mg/L
respectively, and in the effluent, 18.7mg/L and and 18.0mg/L
respectively. Analysis of the performance of the IDEA treatment
system showed that the operational costs can be minimized by 3%, by
decreasing the number of operating cycles. As for the treatment
system in Resort A, by utilizing a smaller capacity air blower, a
saving of 12% could be made in the operational costs.
Abstract: This survey highlights a number of important issues
which relate to the needs to counseling for distance learners studying
at the School of Distance Education in University science Malaysia
(DEUSM) according to their gender. Data were obtained by selfreport
questionnaire that had been developed by the researchers in
counseling and educational psychology and interviews were take
place. 116 voluntary respondents complete the Questionnaire and
returned it back during new student-s registration week.64% of the
respondents were female and 52% were males that means
55%ofthem were females and 45% were males. The data was
analyzed to find out the frequencies of respondents agreements of the
items. The average of the female was 18 and the average of the male
was 19.6 by using t- test there is no significant values between the
genders. The findings show that respondents have needs for
counseling. (22) Significant needs for mails (DEUSM) the highest
was their families complain about the amount of time they spend at
work. (11) Significant needs for females the highest was they
convinced themselves that they only need 4 to 5 hours of sleep per
night.
Abstract: The consumption capability of people in China has
been a big issue to tourism business. Due to the increasing of China
tourists, Taiwan-s government rescinded the category of people in
China and opened up the non-stopped airline from China to Taiwan.
The “one-day traveling style between China and Taiwan" has formed,
hoping to bring business to Taiwan. Night market, which shows
foreigners the very local character of Taiwan, contains various
merchandise for consumers to purchase. With the increasing numbers
of non-stopped airline, visiting Taiwan-s night markets has also been
one of major activities to China-s tourists. The purpose of the present
study is to understand the consumer behavior of China tourists in
tourist night markets in Taipei and analyze that if their shopping
motives cause the different shopping behaviors and post-purchase
satisfaction and revisiting intention. The results reveled that for the
China tourists, the motives of significant influence to the shopping
behaviors. Also, the shopping behaviors significant influence to the
whole satisfaction and the whole satisfaction significant influence to
post-purchase behavior.
Abstract: During signal transmission, the combined effect of the
transmitter filter, the transmission medium, and additive white
Gaussian noise (AWGN) are included in the channel which distort
and add noise to the signal. This causes the well defined signal
constellation to spread causing errors in bit detection. A compact pi
neural network with minimum number of nodes is proposed. The
replacement of summation at each node by multiplication results in
more powerful mapping. The resultant pi network is tested on six
different channels.
Abstract: Recently, Denial of Service(DoS) attacks and Distributed DoS(DDoS) attacks which are stronger form of DoS attacks from plural hosts have become security threats on the Internet. It is important to identify the attack source and to block attack traffic as one of the measures against these attacks. In general, it is difficult to identify them because information about the attack source is falsified. Therefore a method of identifying the attack source by tracing the route of the attack traffic is necessary. A traceback method which uses traffic patterns, using changes in the number of packets over time as criteria for the attack traceback has been proposed. The traceback method using the traffic patterns can trace the attack by matching the shapes of input traffic patterns and the shape of output traffic pattern observed at a network branch point such as a router. The traffic pattern is a shapes of traffic and unfalsifiable information. The proposed trace methods proposed till date cannot obtain enough tracing accuracy, because they directly use traffic patterns which are influenced by non-attack traffics. In this paper, a new traffic pattern matching method using Independent Component Analysis(ICA) is proposed.
Abstract: Fuzzy Cognitive Maps (FCMs) have successfully
been applied in numerous domains to show relations between
essential components. In some FCM, there are more nodes, which
related to each other and more nodes means more complex in system
behaviors and analysis. In this paper, a novel learning method used to
construct FCMs based on historical data and by using data mining
and DEMATEL method, a new method defined to reduce nodes
number. This method cluster nodes in FCM based on their cause and
effect behaviors.
Abstract: Nowadays, efficiency, effectiveness and economy are regarded as the main objectives of managers and the secret of the continuity of an organization in competing economy. In such competing settings, it is essential that the management of an organization has not been neglected and been obliged to identify quickly the opportunities for improving the operation of organization and remove the shortcomings of their managed system in order to use the opportunities for development. Operational auditing is a useful tool for system adjustment and leading an organization toward its objectives. Operational auditing is indeed a viewpoint which identifies the causes of insufficiencies, weaknesses and deficiencies of system and plans to eliminate them. Operational auditing is useful in the effectiveness and optimization of executive managers- decisions and increasing the efficiency and economy of their performance in the future and prevents the waste and incorrect use of resources. Evidence shows that operational auditing is used at a limited level in Iran. This matter raises some questions like the following ones in the minds. Why do a limited number of corporations use operational auditing? Which factors can guarantee its full implementation? What obstacles are there in its implementation? The purpose of this article is to determine executive objectives, the operation domain of operational auditing, the components of operational auditing and the executive obstacles to operational auditing in Iran.
Abstract: power-line networks are promise infrastructure for
broadband services provision to end users. However, the network
performance is affected by stochastic channel changing which is due
to load impedances, number of branches and branched line lengths. It
has been proposed that multi-carrier modulations techniques such as
orthogonal frequency division multiplexing (OFDM), Multi-Carrier
Spread Spectrum (MC-SS), wavelet OFDM can be used in such
environment. This paper investigates the performance of different
indoor topologies of power-line networks that uses MC-SS
modulation scheme.It is observed that when a branch is added in the
link between sending and receiving end of an indoor channel an
average of 2.5dB power loss is found. In additional, when the branch
is added at a node an average of 1dB power loss is found.
Additionally when the terminal impedances of the branch change
from line characteristic impedance to impedance either higher or
lower values the channel performances were tremendously improved.
For example changing terminal load from characteristic impedance
(85 .) to 5 . the signal to noise ratio (SNR) required to attain the
same performances were decreased from 37dB to 24dB respectively.
Also, changing the terminal load from channel characteristic
impedance (85 .) to very higher impedance (1600 .) the SNR
required to maintain the same performances were decreased from
37dB to 23dB. The result concludes that MC-SS performs better
compared with OFDM techniques in all aspects and especially when
the channel is terminated in either higher or lower impedances.
Abstract: The major focus of this work was to characterize hydrodynamics in a packed-bed with and without static mixer by using Computational Fluid Dynamic (CFD). The commercial software: COMSOL MULTIPHYSICSTM Version 3.3 was used to simulate flow fields of mixed-gas reactants i.e. CO and H2. The packed-bed was a single tube with the inside diameter of 0.8 cm and the length of 1.2 cm. The static mixer was inserted inside the tube. The number of twisting elements was 1 with 0.8 cm in diameter and 1.2 cm in length. The packed-bed with and without static mixer were both packed with approximately 700 spherical structures representing catalyst pellets. Incompressible Navier-Stokes equations were used to model the gas flow inside the beds at steady state condition, in which the inlet Reynolds Number (Re) was 2.31. The results revealed that, with the insertion of static mixer, the gas was forced to flow radially inward and outward between the central portion of the tube and the tube wall. This could help improving the overall performance of the packed-bed, which could be utilized for heterogeneous catalytic reaction such as reforming and Fischer- Tropsch reactions.
Abstract: The copper flotation tailings from Konkola Copper
mine in Nchanga, Zambia were used in the study. The purpose of this
study was to determine the leaching characteristics of the tailings
material prior and after the physical beneficiation process is
employed. The Knelson gravity concentrator (KC-MD3) was used for
the beneficiation process. The copper leaching efficiencies and
impurity co-extraction percentages in both the upgraded and the raw
feed material were determined at different pH levels and temperature.
It was observed that the copper extraction increased with an increase
in temperature and a decrease in pH levels. In comparison to the raw
feed sample, the upgraded sample reported a maximum copper
extraction of 69% which was 9%, higher than raw feed % extractions.
The impurity carry over was reduced from 18% to 4 % on the
upgraded sample. The reduction in impurity co-extraction was as a
result of the removal of the reactive gangue elements during the
upgrading process, this minimized the number of side reaction
occurring during leaching.
Abstract: In this paper, the effect of transmission codes on the
performance of coherent square M-ary quadrature amplitude
modulation (CSMQAM) under hybrid selection/maximal-ratio
combining (H-S/MRC) diversity is analysed. The fading channels are
modeled as frequency non-selective slow independent and identically
distributed Rayleigh fading channels corrupted by additive white
Gaussian noise (AWGN). The results for coded MQAM are
computed numerically for the case of (24,12) extended Golay code
and compared with uncoded MQAM under H-S/MRC diversity by
plotting error probabilities versus average signal to noise ratio (SNR)
for various values L and N in order to examine the improvement in
the performance of the digital communications system as the number
of selected diversity branches is increased. The results for no
diversity, conventional SC and Lth order MRC schemes are also
plotted for comparison. Closed form analytical results derived in this
paper are sufficiently simple and therefore can be computed
numerically without any approximations. The analytical results
presented in this paper are expected to provide useful information
needed for design and analysis of digital communication systems
over wireless fading channels.
Abstract: There are two major variants of the Simplex
Algorithm: the revised method and the standard, or tableau method.
Today, all serious implementations are based on the revised method
because it is more efficient for sparse linear programming problems.
Moreover, there are a number of applications that lead to dense linear
problems so our aim in this paper is to present some computational
results on parallel implementation of dense Simplex Method. Our
implementation is implemented on a SMP cluster using C
programming language and the Message Passing Interface MPI.
Preliminary computational results on randomly generated dense
linear programs support our results.
Abstract: The number of the companies accepting RFID in Korea
has been increased continuously due to the domestic development of
information technology. The acceptance of RFID by companies in
Korea enabled them to do business with many global enterprises in a
much more efficient and effective way. According to a survey[33,
p76], many companies in Korea have used RFID for inventory or
distribution manages. But, the use of RFID in the companies in Korea
is in the early stages and its potential value hasn-t fully been realized
yet. At this time, it would be very important to investigate the factors
that affect RFID acceptance. For this study, many previous studies
were referenced and some RFID experts were interviewed. Through
the pilot test, four factors were selected - Security Trust, Employee
Knowledge, Partner Influence, Service Provider Trust - affecting
RFID acceptance and an extended technology acceptance
model(e-TAM) was presented with those factors. The proposed model
was empirically tested using data collected from employees in
companies or public enterprises. In order to analyze some
relationships between exogenous variables and four variables in TAM,
structural equation modeling(SEM) was developed and SPSS12.0 and
AMOS 7.0 were used for analyses. The results are summarized as
follows: 1) security trust perceived by employees positively
influences on perceived usefulness and perceived ease of use; 2)
employee-s knowledge on RFID positively influences on only
perceived ease of use; 3) a partner-s influence for RFID acceptance
positively influences on only perceived usefulness; 4) service provider
trust very positively influences on perceived usefulness and perceived
ease of use 5) the relationships between TAM variables are the same as
the previous studies.