Abstract: Transesterification of candlenut (aleurites moluccana)
oil with methanol using potassium hydroxide as catalyst was
studied. The objective of the present investigation was to produce
the methyl ester for use as biodiesel. The operation variables
employed were methanol to oil molar ratio (3:1 – 9:1), catalyst
concentration (0.50 – 1.5 %) and temperature (303 – 343K). Oil
volume of 150 mL, reaction time of 75 min were fixed as common
parameters in all the experiments. The concentration of methyl ester
was evaluated by mass balance of free glycerol formed which was
analyzed by using periodic acid. The optimal triglyceride conversion
was attained by using methanol to oil ratio of 6:1, potassium
hydroxide as catalyst was of 1%, at room temperature. Methyl ester
formed was characterized by its density, viscosity, cloud and pour
points. The biodiesel properties had properties similar to those of
diesel oil, except for the viscosity that was higher.
Abstract: In the present study, fracture behavior of woven
fabric-reinforced glass/epoxy composite laminates under mode III
crack growth was experimentally investigated and numerically
modeled. Two methods were used for the calculation of the strain
energy release rate: the experimental compliance calibration (CC)
method and the Virtual Crack Closure Technique (VCCT). To
achieve this aim ECT (Edge Crack Torsion) was used to evaluate
fracture toughness in mode III loading (out of plane-shear) at
different crack lengths. Load–displacement and associated energy
release rates were obtained for various case of interest. To
calculate fracture toughness JIII, two criteria were considered
including non-linearity and maximum points in load-displacement
curve and it is observed that JIII increases with the crack length
increase. Both the experimental compliance method and the virtual
crack closure technique proved applicable for the interpretation of the
fracture mechanics data of woven glass/epoxy laminates in mode III.
Abstract: In Peer-to-Peer service networks, where peers offer any kind of publicly available services or applications, intuitive navigation through all services in the network becomes more difficult as the number of services increases. In this article, a concept is discussed that enables users to intuitively browse and use large scale P2P service networks. The concept extends the idea of creating virtual 3D-environments solely based on Peer-to-Peer technologies. Aside from browsing, users shall have the possibility to emphasize services of interest using their own semantic criteria. The appearance of the virtual world shall intuitively reflect network properties that may be of interest for the user. Additionally, the concept comprises options for load- and traffic-balancing. In this article, the requirements concerning the underlying infrastructure and the graphical user interface are defined. First impressions of the appearance of future systems are presented and the next steps towards a prototypical implementation are discussed.
Abstract: The purposes of this research are to study and develop
the algorithm of Thai spoonerism words by semi-automatic computer
programs, that is to say, in part of data input, syllables are already
separated and in part of spoonerism, the developed algorithm is
utilized, which can establish rules and mechanisms in Thai
spoonerism words for bi-syllables by utilizing analysis in elements of
the syllables, namely cluster consonant, vowel, intonation mark and
final consonant. From the study, it is found that bi-syllable Thai
spoonerism has 1 case of spoonerism mechanism, namely
transposition in value of vowel, intonation mark and consonant of
both 2 syllables but keeping consonant value and cluster word (if
any).
From the study, the rules and mechanisms in Thai spoonerism
word were applied to develop as Thai spoonerism word software,
utilizing PHP program. the software was brought to conduct a
performance test on software execution; it is found that the program
performs bi-syllable Thai spoonerism correctly or 99% of all words
used in the test and found faults on the program at 1% as the words
obtained from spoonerism may not be spelling in conformity with
Thai grammar and the answer in Thai spoonerism could be more than
1 answer.
Abstract: In this article the accumulated results out of the effects
and length of the manufacture and production projects in the
university and research standard have been settled with the usefulness
definition of the process of project management for the accessibility
to the proportional pattern in the “time and action" stages. Studies
show that many problems confronted by the researchers in these
projects are connected to the non-profiting of: 1) autonomous timing
for gathering the educational theme, 2) autonomous timing for
planning and pattern, presenting before the construction, and 3)
autonomous timing for manufacture and sample presentation from the
output. The result of this study indicates the division of every
manufacture and production projects into three smaller autonomous
projects from its kind, budget and autonomous expenditure, shape
and order of the stages for the management of these kinds of projects.
In this case study real result are compared with theoretical results.
Abstract: Empty Fruit Bunches (EFB) and Palm Oil Mill
Effluent (POME) are two main wastes from oil palm industries which
contain rich lignocellulose. Degradation of EFB and POME by
microorganisms will produce hydrolytic enzyme which will degrade
cellulose and hemicellulose during composting process. However,
normal composting takes about four to six months to reach maturity.
Hence, application of fungi into compost can shorten the period of
composting. This study identifies the effect of xylanase and cellulase
produced by Aspergillus niger and Trichoderma virens on
composting process using EFB and POME. The degradation of EFB
and POME indicates the lignocellulolytic capacity of Aspergillus
niger and Trichoderma virens with more than 7% decrease in
hemicellulose and more than 25% decrease in cellulose for both
inoculated compost. Inoculation of Aspergillus niger and
Trichoderma virens also increased the enzyme activities during the
composting period compared to the control compost by 21% for both
xylanase and cellulase. Rapid rise in the activities of cellulase and
xylanase was observed by Aspergillus niger with the highest
activities of 14.41 FPU/mg and 3.89 IU/mg, respectively. Increased
activities of cellulase and xylanase also occurred in inoculation of
Trichoderma virens with the highest activities obtained at 13.21
FPU/mg and 4.43 IU/mg, respectively. Therefore, it is evident that
the inoculation of fungi can increase the enzyme activities hence
effectively degrading the EFB and POME.
Abstract: Pretreatment of lignocellulosic biomass materials from
poplar, acacia, oak, and fir with different ionic liquids (ILs)
containing 1-alkyl-3-methyl-imidazolium cations and various anions
has been carried out. The dissolved cellulose from biomass was
precipitated by adding anti-solvents into the solution and vigorous
stirring. Commercial cellulases Celluclast 1.5L and Accelerase 1000
have been used for hydrolysis of untreated and pretreated
lignocellulosic biomass. Among the tested ILs, [Emim]COOCH3
showed the best efficiency, resulting in highest amount of liberated
reducing sugars. Pretreatment of lignocellulosic biomass using
glycerol-ionic liquids combined pretreatment and dilute acid-ionic
liquids combined pretreatment were evaluated and compared with
glycerol pretreatment, ionic liquids pretreatment and dilute acid
pretreatment.
Abstract: In this paper, we apply and compare two generalized estimating equation approaches to the analysis of car breakdowns data in Mauritius. Number of breakdowns experienced by a machinery is a highly under-dispersed count random variable and its value can be attributed to the factors related to the mechanical input and output of that machinery. Analyzing such under-dispersed count observation as a function of the explanatory factors has been a challenging problem. In this paper, we aim at estimating the effects of various factors on the number of breakdowns experienced by a passenger car based on a study performed in Mauritius over a year. We remark that the number of passenger car breakdowns is highly under-dispersed. These data are therefore modelled and analyzed using Com-Poisson regression model. We use the two types of quasi-likelihood estimation approaches to estimate the parameters of the model: marginal and joint generalized quasi-likelihood estimating equation approaches. Under-dispersion parameter is estimated to be around 2.14 justifying the appropriateness of Com-Poisson distribution in modelling underdispersed count responses recorded in this study.
Abstract: A Wireless sensor network (WSN) consists of a set of battery-powered nodes, which collaborate to perform sensing tasks in a given environment. Each node in WSN should be capable to act for long periods of time with scrimpy or no external management. One requirement for this independent is: in the presence of adverse positions, the sensor nodes must be capable to configure themselves. Hence, the nodes for determine the existence of unusual events in their surroundings should make use of position awareness mechanisms. This work approaches the problem by considering the possible unusual events as diseases, thus making it possible to diagnose them through their symptoms, namely, their side effects. Considering these awareness mechanisms as a foundation for highlevel monitoring services, this paper also shows how these mechanisms are included in the primal plan of an intrusion detection system.
Abstract: A large number of chemical, bio-chemical and pollution-control processes use heterogeneous fixed-bed reactors. The use of finite hollow cylindrical catalyst pellets can enhance conversion levels in such reactors. The absence of the pellet core can significantly lower the diffusional resistance associated with the solid phase. This leads to a better utilization of the catalytic material, which is reflected in the higher values for the effectiveness factor, leading ultimately to an enhanced conversion level in the reactor. It is however important to develop a rigorous heterogeneous model for the reactor incorporating the two-dimensional feature of the solid phase owing to the presence of the finite hollow cylindrical catalyst pellet. Presently, heterogeneous models reported in the literature invariably employ one-dimension solid phase models meant for spherical catalyst pellets. The objective of the paper is to present a rigorous model of the fixed-bed reactors containing finite hollow cylindrical catalyst pellets. The reaction kinetics considered here is the widely used Michaelis–Menten kinetics for the liquid-phase bio-chemical reactions. The reaction parameters used here are for the enzymatic degradation of urea. Results indicate that increasing the height to diameter ratio helps to improve the conversion level. On the other hand, decreasing the thickness is apparently not as effective. This could however be explained in terms of the higher void fraction of the bed that causes a smaller amount of the solid phase to be packed in the fixed-bed bio-chemical reactor.
Abstract: Nowadays it is a trend for electronic circuit designers to
integrate all system components on a single-chip. This paper proposed
the design of a single-chip proportional to absolute temperature
(PTAT) sensor including a voltage reference circuit using CEDEC
0.18m CMOS Technology. It is a challenge to design asingle-chip
wide range linear response temperature sensor for many applications.
The channel widths between the compensation transistor and the
reference transistor are critical to design the PTAT temperature sensor
circuit. The designed temperature sensor shows excellent linearity
between -100°C to 200° and the sensitivity is about 0.05mV/°C.
The chip is designed to operate with a single voltage source of 1.6V.
Abstract: The trial in the city, located 170 kilometers from the
Iranian city of Ahvaz was Omidiyeh. The main factor in this project
includes 4 levels in control (without hormones), use of hormones in
the seed, vegetative and flowering stage respectively. And sub-plots
included 3 varieties of vetch in three levels, with local names, was the
jewel in the study of light and Auxin in the vegetative and
reproductive different times in different varieties of vetch was
investigated. This test has been taken in the plots in a randomized
complete block with four replications. In order to study the effects of
the hormone Auxin in the growth stages (seed, vegetative and
flowering) to control (no hormone Auxin) on three local varieties of
vetch, the essence of light and plant height, number of pods per plant,
seed number The pods, seeds per plant, grain weight, grain yield,
plant dry weight and protein content were measured. Among the
vetch varieties for plant height, number of pods per plant, a seed per
plant, grain weight, grain yield, and plant dry weight and protein
levels of 1 percent of plant and seed number per pod per plant at 5%
level of There was no significant difference. Interactions for grain
yield per plant, grain yield and protein levels of 1 percent and the
number of seeds per pod and seed weight are significant differences
in levels 5 and plant height and plant dry weight of the interaction
were INFLUENCE There was no significant difference in them.
Abstract: We propose the use of magneto-optic Kerr effect (MOKE) to realize single-qubit quantum gates. We consider longitudinal and polar MOKE in reflection geometry in which the magnetic field is parallel to both the plane of incidence and surface of the film. MOKE couples incident TE and TM polarized photons and the Hamiltonian that represents this interaction is isomorphic to that of a canonical two-level quantum system. By varying the phase and amplitude of the magnetic field, we can realize Hadamard, NOT, and arbitrary phase-shift single-qubit quantum gates. The principal advantage is operation with magnetically non-transparent materials.
Abstract: IVE toolkit has been created for facilitating research,education and development in the field of virtual storytelling and computer games. Primarily, the toolkit is intended for modelling action selection mechanisms of virtual humans, investigating level-of-detail AI techniques for large virtual environments, and for exploring joint behaviour and role-passing technique (Sec. V). Additionally, the toolkit can be used as an AI middleware without any changes. The main facility of IVE is that it serves for prototyping both the AI and virtual worlds themselves. The purpose of this paper is to describe IVE's features in general and to present our current work - including an educational game - on this platform.
Abstract: Vehicle suspension design must fulfill
some conflicting criteria. Among those is ride comfort
which is attained by minimizing the acceleration
transmitted to the sprung mass, via suspension spring
and damper. Also good handling of a vehicle is a
desirable property which requires stiff suspension and
therefore is in contrast with a vehicle with good ride.
Among the other desirable features of a suspension is
the minimization of the maximum travel of suspension.
This travel which is called suspension working space in
vehicle dynamics literature is also a design constraint
and it favors good ride. In this research a full car 8
degrees of freedom model has been developed and the
three above mentioned criteria, namely: ride, handling
and working space has been adopted as objective
functions. The Multi Objective Programming (MOP)
discipline has been used to find the Pareto Front and
some reasoning used to chose a design point between
these non dominated points of Pareto Front.
Abstract: The traditional Failure Mode and Effects Analysis
(FMEA) uses Risk Priority Number (RPN) to evaluate the risk level
of a component or process. The RPN index is determined by
calculating the product of severity, occurrence and detection indexes.
The most critically debated disadvantage of this approach is that
various sets of these three indexes may produce an identical value of
RPN. This research paper seeks to address the drawbacks in
traditional FMEA and to propose a new approach to overcome these
shortcomings. The Risk Priority Code (RPC) is used to prioritize
failure modes, when two or more failure modes have the same RPN.
A new method is proposed to prioritize failure modes, when there is a
disagreement in ranking scale for severity, occurrence and detection.
An Analysis of Variance (ANOVA) is used to compare means of
RPN values. SPSS (Statistical Package for the Social Sciences)
statistical analysis package is used to analyze the data. The results
presented are based on two case studies. It is found that the proposed
new methodology/approach resolves the limitations of traditional
FMEA approach.
Abstract: This study presents a systematic analysis of the
dynamic behaviors of a gear-bearing system with porous squeeze film
damper (PSFD) under nonlinear suspension, nonlinear oil-film force
and nonlinear gear meshing force effect. It can be found that the
system exhibits very rich forms of sub-harmonic and even the chaotic
vibrations. The bifurcation diagrams also reveal that greater values of
permeability may not only improve non-periodic motions effectively,
but also suppress dynamic amplitudes of the system. Therefore, porous
effect plays an important role to improve dynamic stability of
gear-bearing systems or other mechanical systems. The results
presented in this study provide some useful insights into the design
and development of a gear-bearing system for rotating machinery that
operates in highly rotational speed and highly nonlinear regimes.
Abstract: The dynamical contouring error is a critical element for the accuracy of machine tools. The contouring error is defined as the difference between the processing actual path and commanded path, which is implemented by following the command curves from feeding driving system in machine tools. The contouring error is resulted from various factors, such as the external loads, friction, inertia moment, feed rate, speed control, servo control, and etc. Thus, the study proposes a 2D compensating system for the contouring accuracy of machine tools. Optical method is adopted by using stable frequency laser diode and the high precision position sensor detector (PSD) to performno-contact measurement. Results show the related accuracy of position sensor detector (PSD) of 2D contouring accuracy compensating system was ±1.5 μm for a calculated range of ±3 mm, and improvement accuracy is over 80% at high-speed feed rate.
Abstract: The chemical degradation of dieldrin in ferric
sulfide and iron powder aqueous suspension was investigated
in laboratory batch type experiments. To identify the reaction
mechanism, reduced copper was used as reductant. More than
90% of dieldrin was degraded using both reaction systems after
29 days. Initial degradation rate of the pesticide using ferric
sulfide was superior to that using iron powder. The reaction
schemes were completely dissimilar even though the ferric ion
plays an important role in both reaction systems. In the case of
metallic iron powder, dieldrin undergoes partial dechlorination.
This reaction proceeded by reductive hydrodechlorination with
the generation of H+, which arise by oxidation of ferric iron.
This reductive reaction was accelerated by reductant but
mono-dechlorination intermediates were accumulated. On the
other hand, oxidative degradation was observed in the reaction
with ferric sulfide, and the stable chemical structure of dieldrin
was decomposed into water-soluble intermediates. These
reaction intermediates have no chemical structure of drin class.
This dehalogenation reaction assumes to occur via the adsorbed
hydroxyl radial generated on the surface of ferric sulfide.
Abstract: Resins are used in nuclear power plants for water
ultrapurification. Two approaches are considered in this work:
column experiments and simulations. A software called OPTIPUR
was developed, tested and used. The approach simulates the onedimensional
reactive transport in porous medium with convectivedispersive
transport between particles and diffusive transport within
the boundary layer around the particles. The transfer limitation in the
boundary layer is characterized by the mass transfer coefficient
(MTC). The influences on MTC were measured experimentally. The
variation of the inlet concentration does not influence the MTC; on
the contrary of the Darcy velocity which influences. This is consistent
with results obtained using the correlation of Dwivedi&Upadhyay.
With the MTC, knowing the number of exchange site and the relative
affinity, OPTIPUR can simulate the column outlet concentration
versus time. Then, the duration of use of resins can be predicted in
conditions of a binary exchange.