Abstract: Aluminum alloy sheets have several advantages such
as the lightweight, high-specific strength and recycling efficiency.
Therefore, aluminum alloy sheets in sheet forming have been used in various areas as automotive components and so forth. During the
process of sheet forming, wrinkling which is caused by compression stress might occur and the formability of sheets was affected by
occurrence of wrinkling. A few studies of uniaxial compressive test by
using square tubes, pipes and sheets were carried out to clarify the each wrinkling behavior. However, on uniaxial compressive test,
deformation behavior of the sheets hasn-t be cleared. Then, it is necessary to clarify the relationship between the buckling behavior
and the forming conditions. In this study, the effect of dimension of the sheet in the buckling behavior on compression test of aluminum alloy sheet was cleared by experiment and FEA. As the results, the buckling
deformation was classified by three modes in terms of the distribution of equivalent plastic strain.
Abstract: This paper examines the readability of the chairman’s narratives, as determined by the Flesch score, of a Malaysian public listed company’s corporate reports from 1962 to 2009. It partially supports earlier studies which demonstrated that corporate reports were difficult to read, and had shown very negligible decrease in difficulty over time. Net profit to sales and readability was significantly positively correlated but number of financial statements was significantly negatively correlated with readability.
Abstract: To estimate the risks of dam failure phenomenon, it is necessary to understand this phenomenon and the involved governing factors. Overtopping and piping are the two main reasons of earthdam failures. In the piping context, the piping is determined as a phenomenon which is occurred between two phases, the water liquid and the solid soil. In this investigation, the onset of piping and its development, as well as the movement of water in soil, are numerically approached. In this regard, a one-dimensional numerical model based on the mass-conserving finite-volume method is developed and applied in order to simulate the piping phenomenon in a continuous circular tunnel of given initial length and radius, located between upstream and downstream. The simulation result includes the time-variations of radius along the tunnel until the radius value reaches its critical and the piping phenomenon converts to overtopping.
Abstract: Recently, majors of doctors are divided into terribly lots of detailed areas. However, it is actually not a rare case that a doctor has a patient who is not in his/her major. He/She must judge an assessment and make a medical treatment plan for this patient. According to our investigation, conventional approaches such as image diagnosis cooperation are insufficient. This paper proposes an 'Assessment / Medical Treatment Plan Consulting System'. We have implemented a pilot system based on our proposition. Its effectiveness is clarified by an evaluation.
Abstract: This paper is a simple and systematic approaches to the design and analysis a pulse width modulation (PWM) based sliding mode controller for buck DC-DC Converters. Various aspects of the design, including the practical problems and the proposed solutions, are detailed. However, these control strategies can't compensate for large load current and input voltage variations. In this paper, a new control strategy by compromising both schemes advantages and avoiding their drawbacks is proposed, analyzed and simulated.
Abstract: In this paper, a method based on Non-Dominated
Sorting Genetic Algorithm (NSGA) has been presented for the Volt /
Var control in power distribution systems with dispersed generation
(DG). Genetic algorithm approach is used due to its broad
applicability, ease of use and high accuracy. The proposed method is
better suited for volt/var control problems. A multi-objective
optimization problem has been formulated for the volt/var control of
the distribution system. The non-dominated sorting genetic algorithm
based method proposed in this paper, alleviates the problem of tuning
the weighting factors required in solving the multi-objective volt/var
control optimization problems. Based on the simulation studies
carried out on the distribution system, the proposed scheme has been
found to be simple, accurate and easy to apply to solve the multiobjective
volt/var control optimization problem of the distribution
system with dispersed generation.
Abstract: The integral form of equations of motion of composite
beams subjected to varying time loads are discretized using a
developed finite element model. The model consists of a straight five
node twenty-two degrees of freedom beam element. The stability
analysis of the beams is studied by solving the matrix form
characteristic equations of the system. The principle of virtual work
and the first order shear deformation theory are employed to analyze
the beams with large deformation and small strains. The regions of
dynamic instability of the beam are determined by solving the
obtained Mathieu form of differential equations. The effects of nonconservative
loads, shear stiffness, and damping parameters on
stability and response of the beams are examined. Several numerical
calculations are presented to compare the results with data reported
by other researchers.
Abstract: This study is aimed to investigate feasibility of the
aerobic biological process to treat oily wastewater from palm oil food
industry. Effect of aeration and sludge concentrations are studied.
Raw sludge and raw wastewater was mixed and acclimatized for five
days in a stirred tank reactor. The aeration rate (no aeration, low;
1.5L/min and high rate; 2L/min) and sludge concentration (3675,
7350, and 11025mg/L of VSS) were varied. Responses of process
were pH, COD, oil and grease, VSS, and PHB content. It was found
that the treatment can remove 85.1 to 97.1 % of COD and remove
12.9 to 54.8% of oil & grease. The PHB yield was found to be within
0.15% to 2.4% as PHB/VSS ratio and 0.01% to 0.12% as PHB/COD
removed. The higher aeration results a high COD removal and oil &
grease removal, while experiment without aeration gives better PHB
yield. Higher sludge concentrations (11025mg/L VSS) give higher
removal of oil & grease while moderate sludge concentration
(7350mg/L VSS) give better result in COD removal. Higher PHB
yield is obtained in low sludge concentration (3675mg/L).
Abstract: In this paper we present a novel method, which
reduces the computational complexity of abrupt cut detection. We
have proposed fast algorithm, where the similarity of frames within
defined step is evaluated instead of comparing successive frames.
Based on the results of simulation on large video collection, the
proposed fast algorithm is able to achieve 80% reduction of needed
frames comparisons compared to actually used methods without the
shot cut detection accuracy degradation.
Abstract: The paper reflects current state of popularization of
static elasticity modulus of concrete. This parameter is undoubtedly
very important for designing of concrete structures, and very often
neglected and rarely determined before designing concrete
technology itself. The paper describes assessment and comparison of
four mix designs with almost constant dosage of individual
components. The only difference is area of origin of small size
fraction of aggregate 0/4. Development of compressive strength and
static elasticity modulus at the age of 7, 28 and 180 days were
observed. As the experiment showed, designing of individual
components and their quality are the basic factor influencing
elasticity modulus of current concrete.
Abstract: The main objective of this paper is to provide an efficient tool for delineating brain tumors in three-dimensional magnetic resonance images and set up compression-transmit schemes to distribute result to the remote doctor. To achieve this goal, we use basically a level-sets approach to delineating brain tumors in threedimensional. Then introduce a new compression and transmission plan of 3D brain structures based for the meshes simplification, adapted for time to the specific needs of the telemedicine and to the capacities restricted by wireless network communication. We present here the main stages of our system, and preliminary results which are very encouraging for clinical practice.
Abstract: Estimation of natural frequency of structures is very
important and isn-t usually calculated simply and sometimes
complicated. Lack of knowledge about that caused hard damage and
hazardous effects.
In this paper, with using from two different models in FEM
method and based on hydrodynamic mass of fluids, natural frequency
of an especial bearing (Fig. 1) in an electric field (or, a periodic
force) is calculated in different stiffness and different geometric. In
final, the results of two models and analytical solution are compared.
Abstract: Meta-reasoning is essential for multi-agent communication. In this paper we propose a framework of multi-agent communication in which agents employ meta-reasoning to reason with agent and ontology locations in order to communicate semantic information with other agents on the semantic web and also reason with multiple distributed ontologies. We shall argue that multi-agent communication of Semantic Web information cannot be realized without the need to reason with agent and ontology locations. This is because for an agent to be able to communicate with another agent, it must know where and how to send a message to that agent. Similarly, for an agent to be able to reason with an external semantic web ontology, it must know where and how to access to that ontology. The agent framework and its communication mechanism are formulated entirely in meta-logic.
Abstract: Lignocellulosic materials are considered the most
abundant renewable resource available for the Bioethanol
Production. Water Hyacinth is one of potential raw material of the
world-s worst aquatic plant as a feedstock to produce Bioethanol.
The purposed this research is obtain reduced of matter for
biodegradation lignin in Biological pretreatment with White Rot
Fungi eg. Phanerochaete Chrysosporium using Solid state
Fermentation methods. Phanerochaete Chrysosporium is known to
have the best ability to degraded lignin, but simultaneously it can also
degraded cellulose and hemicelulose. During 8 weeks incubation,
water hyacinth occurred loss of weight reached 34,67%, while loss
of lignin reached 67,21%, loss of cellulose reached 11,01% and loss
of hemicellulose reached 36,56%. The kinetic of losses lignin using
regression linear plot, the results is obtained constant rate (k) of
reduction lignin is -0.1053 and the equation of reduction of lignin
is y = wo - 0, 1.53 x
Abstract: In this paper the complete rotor system including
elastic shaft with distributed mass, allowing for the effects of oil film
in bearings. Also, flexibility of foundation is modeled. As a whole
this article is a relatively complete research in modeling and
vibration analysis of rotor considering gyroscopic effect, damping,
dependency of stiffness and damping coefficients on frequency and
solving the vibration equations including these parameters. On the
basis of finite element method and utilizing four element types
including element of shaft, disk, bearing and foundation and using
MATLAB, a computer program is written. So the responses in
several cases and considering different effects are obtained. Then the
results are compared with each other, with exact solutions and results
of other papers.
Abstract: In this investigation, anatase TiO2 thin films were
grown by radio frequency magnetron sputtering on glass substrates at
a high sputtering pressure and room temperature. The anatase films
were then annealed at 300-600 °C in air for a period of 1 hour. To
examine the structure and morphology of the films, X-ray diffraction
(XRD) and atomic force microscopy (AFM) methods were used
respectively. From X-ray diffraction patterns of the TiO2 films, it was
found that the as-deposited film showed some differences compared
with the annealed films and the intensities of the peaks of the
crystalline phase increased with the increase of annealing
temperature. From AFM images, the distinct variations in the
morphology of the thin films were also observed. The optical
constants were characterized using the transmission spectra of the
films obtained by UV-VIS-IR spectrophotometer. Besides, optical
thickness of the film deposited at room temperature was calculated
and cross-checked by taking a cross-sectional image through SEM.
The optical band gaps were evaluated through Tauc model. It was
observed that TiO2 films produced at room temperatures exhibited
high visible transmittance and transmittance decreased slightly with
the increase of annealing temperatures. The films were found to be
crystalline having anatase phase. The refractive index of the films
was found from 2.31-2.35 in the visible range. The extinction
coefficient was nearly zero in the visible range and was found to
increase with annealing temperature. The allowed indirect optical
band gap of the films was estimated to be in the range from 3.39 to
3.42 eV which showed a small variation. The allowed direct band
gap was found to increase from 3.67 to 3.72 eV. The porosity was
also found to decrease at a higher annealing temperature making the
film compact and dense.
Abstract: In recent years, copulas have become very popular in
financial research and actuarial science as they are more flexible in
modelling the co-movements and relationships of risk factors as compared
to the conventional linear correlation coefficient by Pearson.
However, a precise estimation of the copula parameters is vital in
order to correctly capture the (possibly nonlinear) dependence structure
and joint tail events. In this study, we employ two optimization
heuristics, namely Differential Evolution and Threshold Accepting to
tackle the parameter estimation of multivariate t distribution models
in the EML approach. Since the evolutionary optimizer does not rely
on gradient search, the EML approach can be applied to estimation of
more complicated copula models such as high-dimensional copulas.
Our experimental study shows that the proposed method provides
more robust and more accurate estimates as compared to the IFM
approach.
Abstract: Fertilization plays an important role in crop growth and soil improvement. This study was conducted to determine the best fertilization system for wheat production. Experiments were arranged in a complete block design with three replications in two years. Main plots consisted of six methods of fertilization including (N1): farmyard manure; (N2): compost; (N3): chemical fertilizers; (N4): farmyard manure + compost; (N5): farmyard manure + compost + chemical fertilizers and (N6): control were arranged in sub plots. The addition of compost or farm yard manure significantly increased the soil microbial biomass carbon in comparison to the chemical fertilizer. The dehydrogenase, phosphatase and urease activities in the N3 treatment were significantly lower than in the farm yard manure and compost treatments.
Abstract: This experiment was conducted in attempt of
improving hydrodynamic efficiency of the propulsion mechanism by
installing a spring to the wing so that the opening angle of the wing in
one stroke can be changed automatically, compared to the existing
method of fixed maximum opening angle in Weis-Fogh type ship
propulsion mechanism. Average thrust coefficient was almost fixed
with all velocity ratio with the prototype, but with the spring type,
thrust coefficient increased sharply as velocity ratio increased.
Average propulsive efficiency was larger with bigger opening angle in
the prototype, but in the spring type, the one with smaller spring
coefficient had larger value. In the range over 1.0 in velocity ratio
where big thrust can be generated, spring type had more than twice of
propulsive efficiency increase compared to the prototype.
Abstract: This paper presents the theoretical investigation of a
slotted patch antenna. The main objective of proposed work is to
obtain a large bandwidth antenna with reduced size. The antenna has
a compact size of 21.1mm x 20.25mm x 8.5mm. Two designs with
minor variation are studied which provide wide impedance
bandwidths of 24.056% and 25.63% respectively with the use of
parasitic elements when excited by a probe feed. The advantages of
this configuration are its compact size and the wide range of
frequencies covered. A parametric study is also conducted to
investigate the characteristics of the antenna under different
conditions. The measured return loss and radiation pattern indicate
the suitability of this design for WLAN applications, namely, Wi-
Max, 802.11a/b/g and ISM bands.