Abstract: Detection, feature extraction and pose estimation of
people in images and video is made challenging by the variability of
human appearance, the complexity of natural scenes and the high
dimensionality of articulated body models and also the important
field in Image, Signal and Vision Computing in recent years. In this
paper, four types of people in 2D dimension image will be tested and
proposed. The system will extract the size and the advantage of them
(such as: tall fat, short fat, tall thin and short thin) from image. Fat
and thin, according to their result from the human body that has been
extract from image, will be obtained. Also the system extract every
size of human body such as length, width and shown them in output.
Abstract: This study was conducted published to investigate
there liability of the equation pressure-impulse (PI) reinforced
concrete column inprevious studies. Equation involves three different
levels of damage criteria known as D =0. 2, D =0. 5 and D =0. 8.The
damage criteria known as a minor when 0-0.2, 0.2-0.5is known as
moderate damage, high damage known as 0.5-0.8, and 0.8-1 of the
structure is considered a failure. In this study, two types of reliability
analyzes conducted. First, using pressure-impulse equation with
different parameters. The parameters involved are the concrete
strength, depth, width, and height column, the ratio of longitudinal
reinforcement and transverse reinforcement ratio. In the first analysis
of the reliability of this new equation is derived to improve the
previous equations. The second reliability analysis involves three
types of columns used to derive the PI curve diagram using the
derived equation to compare with the equation derived from other
researchers and graph minimum standoff versus weapon yield
Federal Emergency Management Agency (FEMA). The results
showed that the derived equation is more accurate with FEMA
standards than previous researchers.
Abstract: There are only limited studies that directly correlate
the increase in reinforced concrete (RC) panel structural capacities in
resisting the blast loads with different RC panel structural properties
in terms of blast loading characteristics, RC panel dimensions, steel
reinforcement ratio and concrete material strength. In this paper,
numerical analyses of dynamic response and damage of the one-way
RC panel to blast loads are carried out using the commercial software
LS-DYNA. A series of simulations are performed to predict the blast
response and damage of columns with different level and magnitude
of blast loads. The numerical results are used to develop pressureimpulse
(P-I) diagrams of one-way RC panels. Based on the
numerical results, the empirical formulae are derived to calculate the
pressure and impulse asymptotes of the P-I diagrams of RC panels.
The results presented in this paper can be used to construct P-I
diagrams of RC panels with different concrete and reinforcement
properties. The P-I diagrams are very useful to assess panel capacities
in resisting different blast loads.
Abstract: Forming a legal culture among citizens is a
complicated and lengthy process, influencing all spheres of social
life. It includes promoting justice, learning rights and duties, the
introduction of juridical norms and knowledge, and also a process of
developing a system of legal acts and constitutional norms. Currently,
the evaluative and emotional influence of attempts to establish a legal
culture among the citizens of Kazakhstan is limited by real legal
practice. As a result, the values essential to a sound civil society are
absent from the consciousness of the Kazakh people who are thus, in
turn, not able to develop respect for these values. One of the
disadvantages of the modern Kazakh educational system is a
tendency to underrate the actual forces shaping the worldview of
Kazakh youths. The mass-media, which are going through a
personnel crisis, cannot provide society with the legal and political
information necessary to form the sort of legal culture required for a
true civil society.
Abstract: The Internet has become an indispensable part of our lives. Witnessing recent web-based mass collaboration, e.g. Wikipedia, people are questioning whether the Internet has made fundamental changes to the society or whether it is merely a hyperbolic fad. It has long been assumed that collective action for a certain goal yields the problem of free-riding, due to its non-exclusive and non-rival characteristics. Then, thanks to recent technological advances, the on-line space experienced the following changes that enabled it to produce public goods: 1) decrease in the cost of production or coordination 2) externality from networked structure 3) production function which integrates both self-interest and altruism. However, this research doubts the homogeneity of on-line mass collaboration and argues that a more sophisticated and systematical approach is required. The alternative that we suggest is to connect the characteristics of the goal to the motivation. Despite various approaches, previous literature fails to recognize that motivation can be structurally restricted by the characteristic of the goal. First we draw a typology of on-line mass collaboration with 'the extent of expected beneficiary' and 'the existence of externality', and then we examine each combination of motivation using Benkler-s framework. Finally, we explore and connect such typology with its possible dominant participating motivation.
Abstract: Mycophenolic acid “MPA" is a secondary metabolite
of Penicillium bervicompactum with antibiotic and
immunosuppressive properties. In this study, fermentation process
was established for production of mycophenolic acid by Penicillium
bervicompactum MUCL 19011 in shake flask. The maximum MPA
production, product yield and productivity were 1.379 g/L, 18.6 mg/g
glucose and 4.9 mg/L.h respectively. Glucose consumption, biomass
and MPA production profiles were investigated during fermentation
time. It was found that MPA production starts approximately after
180 hours and reaches to a maximum at 280 h. In the next step, the
effects of methionine and acetate concentrations on MPA production
were evaluated. Maximum MPA production, product yield and
productivity (1.763 g/L, 23.8 mg/g glucose and 6.30 mg/L. h
respectively) were obtained with using 2.5 g/L methionine in culture
medium. Further addition of methionine had not more positive effect
on MPA production. Finally, results showed that the addition of
acetate to the culture medium had not any observable effect on MPA
production.
Abstract: The major urban centers are all facing rapid growth is
most often associated with spreading urbanization, social status of the
car has also changed: it has become a commodity of mass
consumption. There are currently about 5 million and 260 cars in
Algeria (2008), this number increases every year 200,000 new cars.
These phenomena induce a demand for greater mobility and a
significant need for transport infrastructure. Faced with these
problems and development of the growing use of the automobile,
central governments and local authorities in charge of urban transport
issues are aware of the need to develop their urban transport systems
but often lack opportunities.
Urban Transport Plans (PDU) were born in reaction to the "culture
of automobile." Their existence in the world the '80s, however, they
had little success before laws on air and rational use of energy in 90
years does not alter substantially their content and make mandatory
their implementation in cities of over 100,000 inhabitants (Abroad)
[1].
The objective of this work is to use the tool and specifically
Geomatics techniques as decision support in the organization and
management of travel while taking into consideration the influence,
which will then translate by National Urban Transport Plan.
Abstract: The Expert Witness Testimony in the Battered
Woman Syndrome Expert witness testimony (EWT) is a kind of
information given by an expert specialized in the field (here in BWS)
to the jury in order to help the court better understand the case. EWT
does not always work in favor of the battered women. Two main
decision-making models are discussed in the paper: the Mathematical
model and the Explanation model. In the first model, the jurors
calculate ″the importance and strength of each piece of evidence″
whereas in the second model they try to integrate the EWT with the
evidence and create a coherent story that would describe the crime.
The jury often misunderstands and misjudges battered women for
their action (or in this case inaction). They assume that these women
are masochists and accept being mistreated for if a man abuses a
woman constantly, she should and could divorce him or simply leave
at any time. The research in the domain found that indeed, expert
witness testimony has a powerful influence on juror’s decisions thus
its quality needs to be further explored. One of the important factors
that need further studies is a bias called the dispositionist worldview
(a belief that what happens to people is of their own doing). This
kind of attributional bias represents a tendency to think that a
person’s behavior is due to his or her disposition, even when the
behavior is clearly attributed to the situation. Hypothesis The
hypothesis of this paper is that if a juror has a dispositionist
worldview then he or she will blame the rape victim for triggering the
assault. The juror would therefore commit the fundamental
attribution error and believe that the victim’s disposition caused the
rape and not the situation she was in. Methods The subjects in the
study were 500 randomly sampled undergraduate students from
McGill, Concordia, Université de Montréal and UQAM.
Dispositional Worldview was scored on the Dispositionist
Worldview Questionnaire. After reading the Rape Scenarios, each
student was asked to play the role of a juror and answer a
questionnaire consisting of 7 questions about the responsibility,
causality and fault of the victim. Results The results confirm the
hypothesis which states that if a juror has a dispositionist worldview
then he or she will blame the rape victim for triggering the assault.
By doing so, the juror commits the fundamental attribution error
because he will believe that the victim’s disposition, and not the
constraints or opportunities of the situation, caused the rape scenario.
Abstract: The present work presents the extraction of copper(II)
from sulphuric acid solutions with Sodium diethyldithiocarbamate
(SDDT), and six different organic diluents: Dichloromethane,
Chloroform, Carbon tetrachloride, Toluene, xylene and Cyclohexane,
were tested. The pair SDDT/Chloroform showed to be the most
selective in removing the copper cations, and hence was considered
throughout the experimental study.
The effects of operating parameters such as the initial concentration
of the extracting agent, the agitation time, the agitation speed and the
acid concentration were considered.
For an initial concentration of Cu (II) of 63 ppm in a 0.5 M sulphuric
acid solution, both with a mass of the extracting agent of 20 mg, an
extraction percentage of about 97.8 % and a distribution coefficient
of 44.42 were obtained, respectively, confirming the performance
of the SDDT-Chloroform pair.
Abstract: Attempts to add fibre and polyphenols (PPs) into
popular beverages present challenges related to the properties of
finished products such as smoothies. Consumer acceptability,
viscosity and phenolic composition of smoothies containing high
levels of fruit fibre (2.5-7.5 g per 300 mL serve) and PPs (250-750
mg per 300 mL serve) were examined. The changes in total
extractable PP, vitamin C content, and colour of selected smoothies
over a storage stability trial (4°C, 14 days) were compared. A set of
acidic aqueous model beverages were prepared to further examine
the effect of two different heat treatments on the stability and
extractability of PPs. Results show that overall consumer
acceptability of high fibre and PP smoothies was low, with average
hedonic scores ranging from 3.9 to 6.4 (on a 1-9 scale). Flavour,
texture and overall acceptability decreased as fibre and polyphenol
contents increased, with fibre content exerting a stronger effect.
Higher fibre content resulted in greater viscosity, with an elevated PP
content increasing viscosity only slightly. The presence of fibre also
aided the stability and extractability of PPs after heating. A reduction
of extractable PPs, vitamin C content and colour intensity of
smoothies was observed after a 14-day storage period at 4°C. Two
heat treatments (75°C for 45 min or 85°C for 1 min) that are
normally used for beverage production, did not cause significant
reduction of total extracted PPs. It is clear that high levels of added
fibre and PPs greatly influence the consumer appeal of smoothies,
suggesting the need to develop novel formulation and processing
methods if a satisfactory functional beverage is to be developed
incorporating these ingredients.
Abstract: World population growth drives food demand, promotes intensification of agriculture, development of new production technologies and varieties more suitable for regional nature conditions. Climate change can affect the length of growing period, biomass and carbon accumulation in winter wheat. The increasing mean air temperature resulting from climate change can reduce the length of growth period of cereals, and without adequate adjustments in growing technologies or varieties, can reduce biomass and carbon accumulation. Deeper understanding and effective measures for monitoring and management of cereal growth process are needed for adaptation to changing climate and technological conditions.
Abstract: The reduction of hexavalent chromium by scrap iron
was investigated in continuous system, using long-term column
experiments, for aqueous Cr(VI) solutions having low buffering
capacities, over the Cr(VI) concentration range of 5 – 40 mg/L. The
results showed that the initial Cr(VI) concentration significantly
affects the reduction capacity of scrap iron. Maximum reduction
capacity of scrap iron was observed at the beginning of the column
experiments; the lower the Cr(VI) concentration, the greater the
experiment duration with maximum scrap iron reduction capacity.
However, due to passivation of active surface, scrap iron reduction
capacity continuously decreased in time, especially after Cr(VI)
breakthrough. The experimental results showed that highest
reduction capacity recorded until Cr(VI) breakthrough was 22.8 mg
Cr(VI)/g scrap iron, at CI = 5 mg/L, and decreased with increasing
Cr(VI) concentration. In order to assure total reduction of greater
Cr(VI) concentrations for a longer period of time, either the mass of
scrap iron filling, or the hydraulic retention time should be increased.
Abstract: The study site was located in Ratchaburi Province,
Thailand. Four experimental plots in dry dipterocarp forest (DDF)
and four plots in mixed deciduous forest (MDF) were set up to
estimate the above-ground biomass of tree, sapling and bamboo. The
allometry equations were used to investigate above-ground biomass
of these vegetation. Seedling and other understory were determined
using direct harvesting method. Carbon storage in above-ground
biomass was calculated based on IPCC 2006.
The results showed that the above-ground biomass of DDF at
20-40% slope,
Abstract: Turbulence modeling of large-scale flow over a vegetated surface is complex. Such problems involve large scale computational domains, while the characteristics of flow near the surface are also involved. In modeling large scale flow, surface roughness including vegetation is generally taken into account by mean of roughness parameters in the modified law of the wall. However, the turbulence structure within the canopy region cannot be captured with this method, another method which applies source/sink terms to model plant drag can be used. These models have been developed and tested intensively but with a simple surface geometry. This paper aims to compare the use of roughness parameter, and additional source/sink terms in modeling the effect of plant drag on wind flow over a complex vegetated surface. The RNG k-ε turbulence model with the non-equilibrium wall function was tested with both cases. In addition, the k-ω turbulence model, which is claimed to be computationally stable, was also investigated with the source/sink terms. All numerical results were compared to the experimental results obtained at the study site Mason Bay, Stewart Island, New Zealand. In the near-surface region, it is found that the results obtained by using the source/sink term are more accurate than those using roughness parameters. The k-ω turbulence model with source/sink term is more appropriate as it is more accurate and more computationally stable than the RNG k-ε turbulence model. At higher region, there is no significant difference amongst the results obtained from all simulations.
Abstract: To estimate the risks of dam failure phenomenon, it is necessary to understand this phenomenon and the involved governing factors. Overtopping and piping are the two main reasons of earthdam failures. In the piping context, the piping is determined as a phenomenon which is occurred between two phases, the water liquid and the solid soil. In this investigation, the onset of piping and its development, as well as the movement of water in soil, are numerically approached. In this regard, a one-dimensional numerical model based on the mass-conserving finite-volume method is developed and applied in order to simulate the piping phenomenon in a continuous circular tunnel of given initial length and radius, located between upstream and downstream. The simulation result includes the time-variations of radius along the tunnel until the radius value reaches its critical and the piping phenomenon converts to overtopping.
Abstract: This study is aimed to investigate feasibility of the
aerobic biological process to treat oily wastewater from palm oil food
industry. Effect of aeration and sludge concentrations are studied.
Raw sludge and raw wastewater was mixed and acclimatized for five
days in a stirred tank reactor. The aeration rate (no aeration, low;
1.5L/min and high rate; 2L/min) and sludge concentration (3675,
7350, and 11025mg/L of VSS) were varied. Responses of process
were pH, COD, oil and grease, VSS, and PHB content. It was found
that the treatment can remove 85.1 to 97.1 % of COD and remove
12.9 to 54.8% of oil & grease. The PHB yield was found to be within
0.15% to 2.4% as PHB/VSS ratio and 0.01% to 0.12% as PHB/COD
removed. The higher aeration results a high COD removal and oil &
grease removal, while experiment without aeration gives better PHB
yield. Higher sludge concentrations (11025mg/L VSS) give higher
removal of oil & grease while moderate sludge concentration
(7350mg/L VSS) give better result in COD removal. Higher PHB
yield is obtained in low sludge concentration (3675mg/L).
Abstract: In this paper we present a novel method, which
reduces the computational complexity of abrupt cut detection. We
have proposed fast algorithm, where the similarity of frames within
defined step is evaluated instead of comparing successive frames.
Based on the results of simulation on large video collection, the
proposed fast algorithm is able to achieve 80% reduction of needed
frames comparisons compared to actually used methods without the
shot cut detection accuracy degradation.
Abstract: Even it has been recognized that Shape Memory
Alloys (SMA) have a significant potential for deployment actuators,
the number of applications of SMA-based actuators to the present
day is still quite small, due to the need of deep understanding of the
thermo-mechanical behavior of SMA, causing an important need for
a mathematical model able to describe all thermo-mechanical
properties of SMA by relatively simple final set of constitutive
equations. SMAs offer attractive potentials such as: reversible strains
of several percent, generation of high recovery stresses and high
power / weight ratios. The paper tries to provide an overview of the
shape memory functions and a presentation of the designed and
developed temperature control system used for a gripper actuated by
two pairs of differential SMA active springs. An experimental setup
was established, using electrical energy for actuator-s springs heating
process. As for holding the temperature of the SMA springs at certain
level for a long time was developed a control system in order to
avoid the active elements overheating.
Abstract: Estimation of natural frequency of structures is very
important and isn-t usually calculated simply and sometimes
complicated. Lack of knowledge about that caused hard damage and
hazardous effects.
In this paper, with using from two different models in FEM
method and based on hydrodynamic mass of fluids, natural frequency
of an especial bearing (Fig. 1) in an electric field (or, a periodic
force) is calculated in different stiffness and different geometric. In
final, the results of two models and analytical solution are compared.
Abstract: In this paper the complete rotor system including
elastic shaft with distributed mass, allowing for the effects of oil film
in bearings. Also, flexibility of foundation is modeled. As a whole
this article is a relatively complete research in modeling and
vibration analysis of rotor considering gyroscopic effect, damping,
dependency of stiffness and damping coefficients on frequency and
solving the vibration equations including these parameters. On the
basis of finite element method and utilizing four element types
including element of shaft, disk, bearing and foundation and using
MATLAB, a computer program is written. So the responses in
several cases and considering different effects are obtained. Then the
results are compared with each other, with exact solutions and results
of other papers.