Abstract: At certain depths during large diameter displacement
pile driving, rebound well over 0.25 inches was experienced,
followed by a small permanent-set during each hammer blow. High
pile rebound (HPR) soils may stop the pile driving and results in a
limited pile capacity. In some cases, rebound leads to pile damage,
delaying the construction project, and the requiring foundations
redesign. HPR was evaluated at seven Florida sites, during driving of
square precast, prestressed concrete piles driven into saturated, fine
silty to clayey sands and sandy clays. Pile Driving Analyzer (PDA)
deflection versus time data recorded during installation, was used to
develop correlations between cone penetrometer (CPT) pore-water
pressures, pile displacements and rebound. At five sites where piles
experienced excessive HPR with minimal set, the pore pressure
yielded very high positive values of greater than 20 tsf. However, at
the site where the pile rebounded, followed by an acceptable
permanent-set, the measured pore pressure ranged between 5 and 20
tsf. The pore pressure exhibited values of less than 5 tsf at the site
where no rebound was noticed. In summary, direct correlations
between CPTu pore pressure and rebound were produced, allowing
identification of soils that produce HPR.
Abstract: The effect of the inclusion of thyme and rosemary
essential oils into chitosan films, as well as the microbiological and
physical properties when storing chitosan film with and without the
mentioned inclusion was studied. The film forming solution was
prepared by dissolving chitosan (2%, w/v), polysorbate 80 (4% w/w
CH) and glycerol (16% w/w CH) in aqueous lactic acid solutions
(control). The thyme (TEO) and rosemary (REO) essential oils (EOs)
were included 1:1 w/w (EOs:CH) on their combination 50/50
(TEO:REO). The films were stored at temperatures of 5, 20, 33°C
and a relative humidity of 75% during four weeks. The films with
essential oil inclusion did not show an antimicrobial activity against
strains. This behavior could be explained because the chitosan only
inhibits the growth of microorganisms in direct contact with the
active sites. However, the inhibition capacity of TEO was higher than
the REO and a synergic effect between TEO:REO was found for S.
enteritidis strains in the chitosan solution.
Some physical properties were modified by the inclusion of
essential oils. The addition of essential oils does not affect the
mechanical properties (tensile strength, elongation at break, puncture
deformation), the water solubility, the swelling index nor the DSC
behavior. However, the essential oil inclusion can significantly
decrease the thickness, the moisture content, and the L* value of
films whereas the b* value increased due to molecular interactions
between the polymeric matrix, the loosing of the structure, and the
chemical modifications. On the other hand, the temperature and time
of storage changed some physical properties on the chitosan films.
This could have occurred because of chemical changes, such as
swelling in the presence of high humidity air and the reacetylation of
amino groups. In the majority of cases, properties such as moisture
content, tensile strength, elongation at break, puncture deformation,
a*, b*, chrome, 7E increased whereas water resistance, swelling
index, L*, and hue angle decreased.
Abstract: This study presents an attempt to evaluate the
antioxidant potential and antimicrobial activity of methanolic extract,
and essential oils prepared from the leaves of sage (Salvia officinalis
L.). The content of polyphenol in the methanolic extracts from the
leaves of Salvia officinalis was determined spectrophotometrically,
calculated as gallic acid and catechin equivalent. The essential oils
and methanol extract were also subjected to screenings for the
evaluation of their antioxidant activities using 2, 2-diphenyl-1-
picrylhydrazyl (DPPH) test. While the plant essential oils showed
only weak antioxidant activities, its methanol extract was
considerably active in DPPH (IC50 = 37.29 μg/ml) test. Appreciable
total polyphenol content (31.25 mg/g) was also detected for the plant
methanol extract as gallic acid equivalent in the Folin–Ciocalteu test.
The plant was also screened for its antimicrobial activity and good to
moderate inhibitions were recorded for its essential oils, and
methanol extracts against most of the tested microorganisms.
The present investigation revealed that this plant had rich source
of antioxidant properties. It is for this reason that sage has found
increasing application in food formulations.
Abstract: Animal fats (camel, sheep, goat, rabbit and chicken)
and vegetable oils (corn, sunflower, palm oil and olive oil) were
substituted with different proportions (1, 5, 10 and 20%) of lard.
Fatty acid composition in TG and 2-MG were determined using
lipase hydrolysis and gas chromatography before and after
adulteration. Results indicated that, genuine lard had a high
proportion (60.97%) of the total palmitic acid at 2-MG. However, it
was 8.70%, 16.40%, 11.38%, 10.57%, 29.97 and 8.97% for camel,
beef, sheep, goat, rabbit and chicken, respectively. It could be noticed
also the position-2-MG is mostly occupied by unsaturated fatty acids
among all tested fats except lard. Vegetable oils (corn, sunflower,
palm oil and olive oil) revealed that the levels of palmitic acid
esterifies at 2-MG position was 6.84, 1.43, 9.86 and 1.70%,
respectively. It could be observed also the studied oils had a higher
level of unsaturated fatty acids in the same position, compared with
animal fats under investigation. Moreover, palmitic acid esterifies at
2-MG and PAEF increased gradually as the substituted levels
increased among all tested fat and oil samples. Statistical analysis
showed that the PAEF correlated well with lard level. The detection
of lard in some commercial processed foods (5 French fries, 4 Butter
fats, 5 processed meat and 6 candy samples) was carried out. Results
revealed that 2 samples of French fries and 4 samples of processed
meat contained lard due to their higher PAEF, while butter fat and
candy were free of lard.
Abstract: Comprehensive numerical studies have been carried
out to examine the best aerodynamic performance of subsonic aircraft
at different winglet cant angles using a validated 3D k-ω SST model.
In the parametric analytical studies NACA series of airfoils are
selected. Basic design of the winglet is selected from the literature
and flow features of the entire wing including the winglet tip effects
have been examined with different cant angles varying from 150 to
600 at different angles of attack up to 140. We have observed, among
the cases considered in this study that a case, with 150 cant angle the
aerodynamics performance of the subsonic aircraft during takeoff
was found better up to an angle of attack of 2.80 and further its
performance got diminished at higher angles of attack. Analyses
further revealed that increasing the winglet cant angle from 150 to 600
at higher angles of attack could negate the performance deterioration
and additionally it could enhance the peak CL/CD on the order of
3.5%. The investigated concept of variable-cant-angle winglets
appears to be a promising alternative for improving the aerodynamic
efficiency of aircraft.
Abstract: In recent decades with the development of technology
and lack of food sources, sewage sludge in production of human
foods is inevitable. Various sources of municipal and industrial
sewage sludge that is produced can provide the requirement of plant
nutrients. Soils in arid, semi-arid climate of central Iran that most
affected by water drainage, iron and zinc deficiencies, using of
sewage sludge is helpful. Therefore, the aim of this study is
investigation of sewage sludge and manure application on Ni, Pb and
Cd uptake by Savory. An experiment in a randomized complete block
design with three replications was performed. Sewage sludge
treatments consisted of four levels, control, 15, 30, 80 tons per
hectares; the manure was used in four levels of control, 20, 40 and 80
tons per hectare. Results showed that the wet and dry weights was not
affected by sewage sludge using, while, manure has significant effect
on them. The effect of sewage sludge on the cadmium and lead
concentrations were significant. Interactions of sewage sludge and
manure on dry weight values were not significant. Compare mean
analysis showed that increasing the amount of sewage sludge had no
significant effect on cadmium concentration and it reduced when
sewage sludge usage increased. This is probably due to increased
plant growth and reduced concentrations of these elements in the
plant.
Abstract: Essential oils are expensive phytochemicals produced
and extracted from specific species belonging to particular families in
the plant kingdom. In the United Arab Emirates country (UAE), is
located in the arid region of the world, nine species, from the
Lamiaceae family, having the capability to produce therapeutic grade
essential oils. These species include; Mentha spicata, Ocimum
forskolei, Salvia macrosiphon, Salvia aegyptiaca, Salvia macilenta,
Salvia spinosa, Teucrium polium, Teucrium stocksianum and Zataria
multiflora. Although, such potential species are indigenous to the
UAE, however, there are almost no studies available to investigate
the chemical composition and the quality of the extracted essential
oils under the UAE climatological conditions. Therefore, great
attention has to be given to such valuable natural resources, through
conducting highly supported research projects, tailored to the UAE
conditions, and investigating different extraction techniques,
including the application of the latest available technologies, such as
superficial fluid CO2. This is crucially needed; in order to accomplish
the greatest possibilities in the medicinal field, specifically in the
discovery of new therapeutic chemotypes, as well as, to achieve the
sustainability of this natural resource in the country.
Abstract: Collapsible soils go through radical rearrangement of
their particles when triggered by water, stress or/and vibration,
causing loss of volume. This loss of volume in soil as seen in
foundation failures has caused millions of dollars’ worth of damages
to public facilities and infrastructure and so has an adverse effect on
the society and people. Despite these consequences and the several
studies that are available, more research is still required in the study
of soil collapsibility. Discerning the pedogenesis (formation) of soils
and investigating the combined effects of the different geological soil
properties is key to elucidating and quantifying soils collapsibility.
This study presents a novel laboratory testing regime that would be
undertaken on soil samples where the effects of soil type, compactive
variables (moisture content, density, void ratio, degree of saturation)
and loading are analyzed. It is anticipated that results obtained would
be useful in mapping the trend of the combined effect thus the basis
for evaluating soil collapsibility or collapse potentials encountered in
construction with volume loss problems attributed to collapse.
Abstract: Cement-based grouts has been used successfully to
repair cracks in many concrete structures such as bridges, tunnels,
buildings and to consolidate soils or rock foundations. In the present
study the rheological characterization of cement grout with
water/binder ratio (W/B) is fixed at 0.5. The effect of the replacement
of cement by bentonite (2 to 10% wt) in presence of superplasticizer
(0.5% wt) was investigated. Several rheological tests were carried out
by using controlled-stress rheometer equipped with vane geometry in
temperature of 20°C. To highlight the influence of bentonite and
superplasticizer on the rheological behavior of grout cement, various
flow tests in a range of shear rate from 0 to 200 s-1 were observed.
Cement grout showed a non-Newtonian viscosity behavior at all
concentrations of bentonite. Three parameter model Herschel-
Bulkley was chosen for fitting of experimental data. Based on the
values of correlation coefficients of the estimated parameters, The
Herschel-Bulkley law model well described the rheological behavior
of the grouts. Test results showed that the dosage of bentonite
increases the viscosity and yield stress of the system and introduces
more thixotropy. While the addition of both bentonite and
superplasticizer with cement grout improve significantly the fluidity
and reduced the yield stress due to the action of dispersion of SP.
Abstract: Characterization of the engineering behavior of
unsaturated soil is dependent on the soil-water characteristic curve
(SWCC), a graphical representation of the relationship between water
content or degree of saturation and soil suction. A reasonable
description of the SWCC is thus important for the accurate prediction
of unsaturated soil parameters. The measurement procedures for
determining the SWCC, however, are difficult, expensive, and timeconsuming.
During the past few decades, researchers have laid a
major focus on developing empirical equations for predicting the
SWCC, with a large number of empirical models suggested. One of
the most crucial questions is how precisely existing equations can
represent the SWCC. As different models have different ranges of
capability, it is essential to evaluate the precision of the SWCC
models used for each particular soil type for better SWCC estimation.
It is expected that better estimation of SWCC would be achieved via
a thorough statistical analysis of its distribution within a particular
soil class. With this in view, a statistical analysis was conducted in
order to evaluate the reliability of the SWCC prediction models
against laboratory measurement. Optimization techniques were used
to obtain the best-fit of the model parameters in four forms of SWCC
equation, using laboratory data for relatively coarse-textured (i.e.,
sandy) soil. The four most prominent SWCCs were evaluated and
computed for each sample. The result shows that the Brooks and
Corey model is the most consistent in describing the SWCC for sand
soil type. The Brooks and Corey model prediction also exhibit
compatibility with samples ranging from low to high soil water
content in which subjected to the samples that evaluated in this study.
Abstract: The aim of the present study is to investigate the
potential use of the selected seed oils. The oil was extracted using
Soxhlet apparatus and the physicochemical characteristics of the oil
determined using standard methods. The following results were
obtained for the physicochemical parameters analysed: for Egusi seed
oil, Oil yield 53.20%, Saponification value 178.03±1.25 mgKOH/g,
Iodine value 49.10±0.32 g I2/100g, Acid value 4.30±0.86 mgKOH/g,
and Peroxide value 5.80±0.27 meq/kg were obtained. For Pawpaw
seed oil, Oil yield 40.10%, Saponification value 24.13±3.93
mgKOH/g, Iodine value 24.87±0.19 g I2/100g, Acid value 9.46±0.40
mgKOH/g, and Peroxide value 3.12±1.22 meq/kg were obtained. For
Sweet orange seed oil, Oil yield 43.10%, Saponification value
106.30±2.37 mgKOH/g, Iodine value 37.08±0.04 g I2/100g, Acid
value 7.59±0.77 mgKOH/g, and Peroxide value 2.21±0.46 meq/kg
were obtained. From the obtained values of the determined
parameters, the oils can be extracted from the three selected seeds in
commercial quantities and that the egusi and sweet orange seed oils
may be utilized in the industrial soap production.
Abstract: Lead (Pb) poisoning is one of the most common and
preventable environmental health problems. There are different
sources of environmental pollution with lead as lead alkyl additives
in petrol and manufacturing processes. Pb in the atmosphere can be
deposited in urban soils, and may then be re-suspended to re-enter the
atmosphere. This could increase human exposure to Pb and cause
long-term health effects. Thus, monitoring Pb pollution is considered
one of the major tasks in controlling pollution. Scalp hair can be
utilized for the determination of lead (Pb) concentration. It provides a
lasting record of metal intakes of weeks or even months, and for most
metals, their accumulation in hair reflects their accumulation in the
whole body. This work was conducted to investigate the
concentration of lead in male scalp hair of Cairo (residential-traffic
and residential-industrial) and rural residents after twenty years of
phasing out of leaded gasoline. Results indicated that the mean
concentration of lead in hair of residential-traffic (9.7552 μg/g ±0.71)
and residential-industrial (12.3288 μg/g ±1.13) was significantly
higher than that in rural residents (4.7327 μg/g ±0.67). The mean
concentration of lead in hair of resident’s industrial areas was the
highest among Cairo residents and not the traffic areas as it was
before phasing out of leaded gasoline. Twenty years of phasing out of
leaded gasoline in Cairo has greatly improved the lead pollution
among residents of traffic areas, but industrial areas residents were
still suffering from lead pollution, which needs more efforts to
control the sources of lead pollution.
Abstract: Castor (Ricinus communis L.) is one of the important
non-edible oilseed crops having immense industrial and medicinal
value. Oil yield per unit area is the ultimate target in growing oilseed
plants and sowing date is one of the important factors which have a
clear role on production of active substances particularly in oilseeds.
This study was conducted to evaluate the effect of sowing date on the
seed and oil yield of castor in Central Anatolia of Turkey in 2011.
The field experiment was set up in a completely randomized block
design with three replications. Black Diamond-2 castor cultivar was
used as plant material. The treatment was four sowing dates of May
10, May 25, June 10, June 25. In this research; seed yield, oil content
and oil yield were investigated. Results showed that the effect of
different sowing dates were significant on all of characteristics. In
general; delayed sowing dates, resulted in decreased seed yield, oil
content and oil yield. The highest value of seed yield, oil content and
oil yield (respectively, 2523.7 kg ha-1, 51.18% and 1292.2 kg ha-1)
were obtained from the first sowing date (May 10) while the lowest
seed yield, oil content and oil yield (respectively, 1550 kg ha-1,
43.67%, 677.3 kg ha-1) were recorded from the latest sowing date
(June 25). Therefore, it can be concluded that early May could be
recommended as an appropriate sowing date in the studied location
and similar climates for achieved high oil yield of castor.
Abstract: Effects of insertion of coiled wire in juxtaposition with twisted tapes on heat transfer rate and solar radiation without disturbing the flow inside the riser tubes in a solar flat plate collector is experimentally reconnoitered in this present work. The wire coil used as a turbulator is placed inside the riser tube while the twisted tape is inserted into the wire coil to create a continuous swirling flow along the tube wall. The results of the heat transfer have been compared well with the available results. The heat transfer rate in the collector has been found to be increased by 18% to 70%. Solar water heaters having inserts in the flow tubes perform better than the conventional plain ones. It has been observed that heat losses are reduced consequently increasing the thermal performance about 30% over the plain water heaters under the same operating conditions. The effect of twisted tape with wire coils, flow Reynolds number, and the intensity of solar radiation on the thermal performance of the solar water heater has been presented. Effects of insertion of coiled wire in juxtaposition with twisted tapes on heat transfer rate and solar radiation without disturbing the flow inside the riser tubes in a solar flat plate collector is experimentally reconnoitered in this present work. The wire coil used as a turbulator is placed inside the riser tube while the twisted tape is inserted into the wire coil to create a continuous swirling flow along the tube wall. The results of the heat transfer have been compared well with the available results. The heat transfer rate in the collector has been found to be increased by 18% to 70%. Solar water heaters having inserts in the flow tubes perform better than the conventional plain ones. It has been observed that heat losses are reduced consequently increasing the thermal performance about 30% over the plain water heaters under the same operating conditions. The effect of twisted tape with wire coils, flow Reynolds number, and the intensity of solar radiation on the thermal performance of the solar water heater has been presented.
Abstract: Various biomass based resources, which can be used
as an extender, or a complete substitute of diesel fuel may have very
significant role in the development of agriculture, industrial and
transport sectors in the energy crisis. Use of Karanja oil methyl ester
biodiesel in a CI DI engine was found highly compatible with engine
performance along with lower exhaust emission as compared to
diesel fuel but with slightly higher NOx emission and low wear
characteristics. The combustion related properties of vegetable oils
are somewhat similar to diesel oil. Neat vegetable oils or their blends
with diesel, however, pose various long-term problems in
compression ignition engines. These undesirable features of
vegetable oils are because of their inherent properties like high
viscosity, low volatility, and polyunsaturated character. Pongamia
methyl ester (PME) was prepared by transesterification process using
methanol for long term engine operations. The physical and
combustion-related properties of the fuels thus developed were found
to be closer to that of the diesel. A neat biodiesel (PME) was selected
as a fuel for the tribological study of biofuels.
Two similar new engines were completely disassembled and
subjected to dimensioning of various vital moving parts and then
subjected to long-term endurance tests on neat biodiesel and diesel
respectively. After completion of the test, both the engines were
again disassembled for physical inspection and wear measurement of
various vital parts. The lubricating oil samples drawn from both
engines were subjected to atomic absorption spectroscopy (AAS) for
measurement of various wear metal traces present. The additional
lubricating property of biodiesel fuel due to higher viscosity as
compared to diesel fuel resulted in lower wear of moving parts and
thus improved the engine durability with a bio-diesel fuel. Results
reported from AAS tests confirmed substantially lower wear and thus
improved life for biodiesel operated engines.
Abstract: The rapid expansion of deserts in recent decades as a result of human actions combined with climatic changes has highlighted the necessity to understand biological processes in arid environments. Whereas physical processes and the biology of flora and fauna have been relatively well studied in marginally used arid areas, knowledge of desert soil micro-organisms remains fragmentary. The objective of this study is to conduct a diversity analysis of bacterial communities in unvegetated arid soils. Several biological phenomena in hot deserts related to microbial populations and the potential use of micro-organisms for restoring hot desert environments. Dry land ecosystems have a highly heterogeneous distribution of resources, with greater nutrient concentrations and microbial densities occurring in vegetated than in bare soils. In this work, we found it useful to use techniques of artificial intelligence in their treatment especially artificial neural networks (ANN). The use of the ANN model, demonstrate his capability for addressing the complex problems of uncertainty data.
Abstract: Composting is a controlled technology to enhance the
natural aerobic process of organic wastes degradation. The resulting
product is a humified material that is principally recyclable for
agricultural purpose. The composting process is one of the most
important tools for waste management, by the European Community
legislation. In recent years composting has been increasingly used as
a remediation technology to remove biodegradable contaminants
from soil, and to modulate heavy metals bioavailability in
phytoremediation strategies. An optimization in the recovery of
resources from wastes through composting could enhance soil
fertility and promote its use in the remediation biotechnologies of
contaminated soils.
Abstract: The problem of magnetohydrodynamics boundary layer flow and heat transfer on a permeable stretching surface in a second grade nanofluid under the effect of heat generation and partial slip is studied theoretically. The Brownian motion and thermophoresis effects are also considered. The boundary layer equations governed by the PDE’s are transformed into a set of ODE’s with the help of local similarity transformations. The differential equations are solved by variational finite element method. The effects of different controlling parameters on the flow field and heat transfer characteristics are examined. The numerical results for the dimensionless velocity, temperature and nanoparticle volume fraction as well as the reduced Nusselt and Sherwood number have been presented graphically. The comparison confirmed excellent agreement. The present study is of great interest in coating and suspensions, cooling of metallic plate, oils and grease, paper production, coal water or coal-oil slurries, heat exchangers technology, materials processing exploiting.
Abstract: Excavation of shallow tunnels such as subways in urban areas plays a significant role as a life line and investigation of the soil behavior against tunnel construction is one of the vital subjects studied in the geotechnical scope. Nowadays, urban tunnels are mostly drilled by T.B.Ms and changing the applied forces to tunnel lining is one of the most risky matters while drilling tunnels by these machines. Variation of soil cementation can change the behavior of these forces in the tunnel lining. Therefore, this article is designed to assess the impact of tunnel excavation in different soils and several amounts of cementation on applied loads to tunnel lining under static and dynamic loads. According to the obtained results, changing the cementation of soil will affect the applied loadings to the tunnel envelope significantly. It can be determined that axial force in tunnel lining decreases considerably when soil cementation increases. Also, bending moment and shear force in tunnel lining decreases as the soil cementation increases and causes bending and shear behavior of the segments to improve. Based on the dynamic analyses, as cohesion factor in soil increases, bending moment, axial and shear forces of segments decrease but lining behavior of the tunnel is the same as static state. The results show that decreasing the overburden applied to lining caused by cementation is different in two static and dynamic states.
Abstract: Oil leakage from the pipelines and the tanks carrying them, or during oil extraction, could lead to the changes in the characteristics and properties of the soil. In this paper, conducting a series of experimental cyclic triaxial tests, the effects of oil contamination on the liquefaction potential of sandy soils is investigated. The studied specimens are prepared by mixing the Firoozkuh sand with crude oil in 4, 8 and 12 percent by soil dry weight. The results show that the oil contamination up to 8% causes an increase in the soil liquefaction resistance and then with increase in the contamination, the liquefaction resistance decreases.