Abstract: Sedimentation formation is a complex hydraulic phenomenon that has emerged as a major operational and maintenance consideration in modern hydraulic engineering in general and river engineering in particular. Sediments accumulation along the river course and their eventual storage in a form of islands affect water intake in the canal systems that are fed by the storage reservoirs. Without proper management, sediment transport can lead to major operational challenges in water distribution system of arid regions like the Dez and Hamidieh command areas. The paper aims to investigate sedimentation in the Western Canal of Dez Diversion Weir using the SHARC model and compare the results with the two intake structures of the Hamidieh dam in Iran using SSIIM model. The objective was to identify the factors which influence the process, check reliability of outcome and provide ways in which to mitigate the implications on operation and maintenance of the structures. Results estimated sand and silt bed loads concentrations to be 193 ppm and 827ppm respectively. This followed ,ore or less similar pattern in Hamidieh where the sediment formation impeded water intake in the canal system. Given the available data on average annual bed loads and average suspended sediment loads of 165ppm and 837ppm in the Dez, there was a significant statistical difference (16%) between the sand grains, whereas no significant difference (1.2%) was find in the silt grain sizes. One explanation for such finding being that along the 6 Km river course there was considerable meandering effects which explains recent shift in the hydraulic behavior along the stream course under investigation. The sand concentration in downstream relative to present state of the canal showed a steep descending curve. Sediment trapping on the other hand indicated a steep ascending curve. These occurred because the diversion weir was not considered in the simulation model. The comparative study showed very close similarities in the results which explains the fact that both software can be used as accurate and reliable analytical tools for simulation of the sedimentation in hydraulic engineering.
Abstract: Scouring around a bridge pier is a complex
phenomenon. More laboratory experiments are required to
understand the scour mechanism. This paper focused on time
development of local scour around piers and piles in semi integral
bridges. Laboratory data collected at Hydraulics Laboratory,
University of Malaya was analyzed for this purpose. Tests were
performed with two different uniform sediment sizes and five ranges
of flow velocities. Fine and coarse sediments were tested in the
flume. Results showed that scour depths for both pier and piles
increased with time up to certain levels and after that they became
almost constant. It had been found that scour depths increased when
discharges increased. Coarser sediment also produced lesser scouring
at the piers and combined piles.
Abstract: This work proposes a recursive weighted ELS
algorithm for system identification by applying numerically robust
orthogonal Householder transformations. The properties of the
proposed algorithm show it obtains acceptable results in a noisy
environment: fast convergence and asymptotically unbiased
estimates. Comparative analysis with others robust methods well
known from literature are also presented.
Abstract: In this work we study analytically and numerically the
performance of the mean heave motion of an OWC coupled with the
governing equation of the spreading ocean waves due to the wide
variation in an open parabolic channel with constant depth. This
paper considers that the ocean wave propagation is under the
assumption of a shallow flow condition. In order to verify the effect
of the waves in the OWC firstly we establish the analytical model in
a non-dimensional form based on the energy equation. The proposed
wave-power system has to aims: one is to perturb the ocean waves as
a consequence of the channel shape in order to concentrate the
maximum ocean wave amplitude in the neighborhood of the OWC
and the second is to determine the pressure and volume oscillation of
air inside the compression chamber.
Abstract: This paper considers the exclusion of consumer rights by the New Zealand Consumer Guarantees Act 1993 in eauctions. The paper asserts that the absence of an individual auctioneer conducting each e-auction means that e-auctions may not be auctions at all. The paper also questions the justification for excluding consumer rights in e-auctions because the rationale for excluding consumer rights in traditional auctions does not fit with e-auctions due to the significant differences in the sale processes. The paper recommends reform by way of statutory amendment.
Abstract: A complete CAD procedure to model a twisted-bladed
vertical-axis wind turbine (VAWT) is presented with the aim of
determining some practical guidelines to be used for the generation
of an easily-meshable CAD geometry to be adopted as the basis of
both CFD and FEM numerical simulations.
Abstract: Swarm principles are increasingly being used to design controllers for the coordination of multi-robot systems or, in general, multi-agent systems. This paper proposes a two-dimensional Lagrangian swarm model that enables the planar agents, modeled as point masses, to swarm whilst effectively avoiding each other and obstacles in the environment. A novel method, based on an extended Lyapunov approach, is used to construct the model. Importantly, the Lyapunov method ensures a form of practical stability that guarantees an emergent behavior, namely, a cohesive and wellspaced swarm with a constant arrangement of individuals about the swarm centroid. Computer simulations illustrate this basic feature of collective behavior. As an application, we show how multiple planar mobile unicycle-like robots swarm to eventually form patterns in which their velocities and orientations stabilize.
Abstract: Female breast cancer is the second in frequency after cervical cancer. Surgery is the most common treatment for breast cancer, followed by chemotherapy as a treatment of choice. Although effective, it causes serious side effects. Controlled-release drug delivery is an alternative method to improve the efficacy and safety of the treatment. It can release the dosage of drug between the minimum effect concentration (MEC) and minimum toxic concentration (MTC) within tumor tissue and reduce the damage of normal tissue and the side effect. Because an in vivo experiment of this system can be time-consuming and labor-intensive, a mathematical model is desired to study the effects of important parameters before the experiments are performed. Here, we describe a 3D mathematical model to predict the release of doxorubicin from pluronic gel to treat human breast cancer. This model can, ultimately, be used to effectively design the in vivo experiments.
Abstract: The task of face recognition has been actively
researched in recent years. This paper provides an up-to-date review of major human face recognition research. We first present an
overview of face recognition and its applications. Then, a literature review of the most recent face recognition techniques is presented.
Description and limitations of face databases which are used to test
the performance of these face recognition algorithms are given. A
brief summary of the face recognition vendor test (FRVT) 2002, a
large scale evaluation of automatic face recognition technology, and
its conclusions are also given. Finally, we give a summary of the research results.
Abstract: A generalized unified power quality conditioner
(GUPQC) by using three single-phase three-level voltage source
converters (VSCs) connected back-to-back through a common dc
link is proposed in this paper as a new custom power device for a
three-feeder distribution system. One of the converters is connected
in shunt with one feeder for mitigation of current harmonics and
reactive power compensation, while the other two VSCs are
connected in series with the other two feeders to maintain the load
voltage sinusoidal and at constant level. A new control scheme based
on synchronous reference frame is proposed for series converters.
The simulation analysis on compensation performance of GUPQC
based on PSCAD/EMTDC is reported.
Abstract: This paper presents a new algorithm for the channel estimation of the OFDM system based on a pilot signal for the new generation of high data rate communication systems. In orthogonal frequency division multiplexing (OFDM) systems over fast-varying fading channels, channel estimation and tracking is generally carried out by transmitting known pilot symbols in given positions of the frequency-time grid. In this paper, we propose to derive an improved algorithm based on the calculation of the mean and the variance of the adjacent pilot signals for a specific distribution of the pilot signals in the OFDM frequency-time grid then calculating of the entire unknown channel coefficients from the equation of the mean and the variance. Simulation results shows that the performance of the OFDM system increase as the length of the channel increase where the accuracy of the estimated channel will be increased using this low complexity algorithm, also the number of the pilot signal needed to be inserted in the OFDM signal will be reduced which lead to increase in the throughput of the signal over the OFDM system in compared with other type of the distribution such as Comb type and Block type channel estimation.
Abstract: The technological concepts such as wireless hospital
and portable cardiac telemetry system require the development of
physiological signal acquisition devices to be easily integrated into
the hospital database. In this paper we present the low cost, portable
wireless ECG acquisition hardware that transmits ECG signals to a
dedicated computer.The front end of the system obtains and
processes incoming signals, which are then transmitted via a
microcontroller and wireless Bluetooth module. A monitoring
purpose Bluetooth based end user application integrated with patient
database management module is developed for the computers. The
system will act as a continuous event recorder, which can be used to
follow up patients who have been resuscitatedfrom cardiac arrest,
ventricular tachycardia but also for diagnostic purposes for patients
with arrhythmia symptoms. In addition, cardiac information can be
saved into the patient-s database of the hospital.
Abstract: We review a knowledge extractor model in
constructing 3G Killer Applications. The success of 3G is essential
for Government as it became part of Telecommunications National
Strategy. The 3G wireless technologies may reach larger area and
increase country-s ICT penetration. In order to understand future
customers needs, the operators require proper information
(knowledge) lying inside. Our work approached future customers as
complex system where the complex knowledge may expose regular
behavior. The hidden information from 3G future customers is
revealed by using fractal-based questionnaires. Afterward, further
statistical analysis is used to match the results with operator-s
strategic plan. The developments of 3G applications also consider its
saturation time and further improvement of the application.
Abstract: The standard investigational method for obstructive
sleep apnea syndrome (OSAS) diagnosis is polysomnography (PSG),
which consists of a simultaneous, usually overnight recording of
multiple electro-physiological signals related to sleep and
wakefulness. This is an expensive, encumbering and not a readily
repeated protocol, and therefore there is need for simpler and easily
implemented screening and detection techniques. Identification of
apnea/hypopnea events in the screening recordings is the key factor
for the diagnosis of OSAS. The analysis of a solely single-lead
electrocardiographic (ECG) signal for OSAS diagnosis, which may
be done with portable devices, at patient-s home, is the challenge of
the last years. A novel artificial neural network (ANN) based
approach for feature extraction and automatic identification of
respiratory events in ECG signals is presented in this paper. A
nonlinear principal component analysis (NLPCA) method was
considered for feature extraction and support vector machine for
classification/recognition. An alternative representation of the
respiratory events by means of Kohonen type neural network is
discussed. Our prospective study was based on OSAS patients of the
Clinical Hospital of Pneumology from Iaşi, Romania, males and
females, as well as on non-OSAS investigated human subjects. Our
computed analysis includes a learning phase based on cross signal
PSG annotation.
Abstract: Malting is usually carried out on intact barley seed,
while hull is still attached to it. In this study, oat grain with and
without hull was subjected to controlled germination to optimize its
enzymes activity, in such a way that lipase has the lowest and α-
amylase and proteinase the highest activities. Since pH has a great
impact on the activity of the enzymes, the pH of germination media
was set up to 3 to 8. In dehulled oats, lipase and α-amylase had the
lowest and highest activities in pHs 3 and 6, respectively whereas the
highest proteinase activity was evidenced at pH 7 and 4 in the oats
with and without hull respectively. While measurements indicated
that the effect of hull on the enzyme activities particularly in lipase
and amylase at each level of the pH are significantly different, the
best results were obtained in those samples in which their hull had
been removed. However, since the similar lipase activity in
germinated dehulled oat were recorded at the pHs 4 and 5, therefore
it was concluded that pH 5 in dehulled oat seed may provide the
optimum enzyme activity for all the enzymes.
Abstract: The techniques for estimating the adhesive and cohesive strength in high velocity oxy fuel (HVOF) thermal spray coatings have been discussed and compared. The development trend and the last investigation have been studied. We will focus on benefits and limitations of these methods in different process and materials.
Abstract: We derive simple sets of equations to describe the microwave response of a thin film of magnetized hydrogen plasma in the presence of carbon nanotubes, which were grown by ironcatalyzed high-pressure disproportionation (HiPco). By considering the interference effects due to multiple reflections between thin plasma film interfaces, we present the effects of the continuously changing external magnetic field and plasma parameters on the reflected power, absorbed power, and transmitted power in the system. The simulation results show that the interference effects play an important role in the reflectance, transmittance and absorptance of microwave radiation at the magnetized plasma slab. As a consequence, the interference effects lead to a sinusoidal variation of the reflected intensity and can greatly reduce the amount of reflection power, but the absorption power increases.
Abstract: Poly (ethylene glycol) (PEG) molecules attached to surfaces have shown high potential as a protein repellent due to their flexibility and highly water solubility. A quartz crystal microbalance recording frequency and dissipation changes (QCM-D) has been used to study the adsorption from aqueous solutions, of lysozyme and α-lactalbumin proteins (the last with and without calcium) onto modified stainless steel surfaces. Surfaces were coated with poly(ethylene imine) (PEI) and silicate before grafting on PEG molecules. Protein adsorption was also performed on the bare stainless steel surface as a control. All adsorptions were conducted at 23°C and pH 7.2. The results showed that the presence of PEG molecules significantly reduced the adsorption of lysozyme and α- lactalbumin (with calcium) onto the stainless steel surface. By contrast, and unexpected, PEG molecules enhanced the adsorption of α-lactalbumin (without calcium). It is suggested that the PEG -α- lactalbumin hydrophobic interaction plays a dominant role which leads to protein aggregation at the surface for this latter observation. The findings also lead to the general conclusion that PEG molecules are not a universal protein repellent. PEG-on-PEI surfaces were better at inhibiting the adsorption of lysozyme and α-lactalbumin (with calcium) than with PEG-on-silicate surfaces.
Abstract: Uncertainties of a serial production line affect on the
production throughput. The uncertainties cannot be prevented in a
real production line. However the uncertain conditions can be
controlled by a robust prediction model. Thus, a hybrid model
including autoregressive integrated moving average (ARIMA) and
multiple polynomial regression, is proposed to model the nonlinear
relationship of production uncertainties with throughput. The
uncertainties under consideration of this study are demand, breaktime,
scrap, and lead-time. The nonlinear relationship of production
uncertainties with throughput are examined in the form of quadratic
and cubic regression models, where the adjusted R-squared for
quadratic and cubic regressions was 98.3% and 98.2%. We optimized
the multiple quadratic regression (MQR) by considering the time
series trend of the uncertainties using ARIMA model. Finally the
hybrid model of ARIMA and MQR is formulated by better adjusted
R-squared, which is 98.9%.
Abstract: This paper deals with new concept of using compressed atmospheric air as a zero pollution power source for running motorbikes. The motorbike is equipped with an air turbine in place of an internal combustion engine, and transforms the energy of the compressed air into shaft work. The mathematical modeling and performance evaluation of a small capacity compressed air driven vaned type novel air turbine is presented in this paper. The effect of isobaric admission and adiabatic expansion of high pressure air for different rotor to casing diameter ratios with respect to different vane angles (number of vanes) have been considered and analyzed. It is found that the shaft work output is optimum for some typical values of rotor / casing diameter ratios at a particular value of vane angle (no. of vanes). In this study, the maximum power is obtained as 4.5kW - 5.3kW (5.5-6.25 HP) when casing diameter is taken 100 mm, and rotor to casing diameter ratios are kept from 0.65 to 0.55. This value of output is sufficient to run motorbike.