Abstract: Analysis of reciprocating equipment piston rod leads
to nonlinear elastic-plastic deformation analysis of rod with initial
imperfection under axial dynamic load. In this paper a new and
effective model and analytical formulations are presented to evaluate
dynamic deformation and elastic-plastic stresses of reciprocating
machine piston rod. This new method has capability to account for
geometric nonlinearity, elastic-plastic deformation and dynamic
effects. Proposed method can be used for evaluation of piston rod
performance for various reciprocating machines under different
operation situations. Rod load curves and maximum allowable rod
load are calculated with presented method for a refinery type
reciprocating compressor. Useful recommendations and guidelines
for rod load, rod load reversal and rod drop monitoring are also
addressed.
Abstract: This paper proposes a robot able to climb Columns.
This robot is not dependent on the diameter and material of the
columns. Some climbing robots have been designed up to now but
Koala robot was designed and fabricated for climbing columns
exclusively. Simple kinematics of climbing in the nature inspired us
to design this robot. We used two linear mechanisms to grip the
column. The gripper consists of a DC motor and a power screw
mechanism with a linear bushing as a guide. This mechanism
provides enough force to grip the column. In addition we needed an
actuator for climbing the column; hence, two pneumatic jacks were
used. All the mechanical parts were designed according to the
exerted forces and operational condition. The prototype can be
simply installed and controlled on the column by an inexperienced
operator. This robot is intended for inspection and surveillance of
pipes in oil industries and power poles in electric industries.
Abstract: This paper deals with rheological behavior of tomato
paste from the view point of time independent properties inclusive of
processing variables such as sample temperature which influence on
rheological properties as well as breaking temperature and
concentration which beside the rheological properties, influence on
the quality of final product. With this aim 10 tomato paste samples at
various concentrations (17-25%) and breaking temperatures (65-
85 C o ) have been produced. The experimental results showed tomato
paste behaves as a non-Newtonian semi-fluid which follows power
law model that consistency coefficient (K) is supposed function of
breaking temperature, concentration and sample temperature with
consideration to superimpose function.
Abstract: This study investigates the roles of knowledge
acquisition, absorptive capacity, and innovation capability in finance
and manufacturing industries. With 362 valid questionnaires from
manufactures and financial industries in Taiwan, we examine the
relationships between absorptive capacity, knowledge acquisition and
innovation capability using a structural equation model. The results
indicate that absorptive capacity is the mediator between knowledge
acquisition and innovation capability, and that knowledge acquisition
has a positive effect on absorptive capacity.
Abstract: In order to implement flexibility as well as survivable
capacities over passive optical network (PON), a new automatic
random fault-recovery mechanism with array-waveguide-grating
based (AWG-based) optical switch (OSW) is presented. Firstly,
wavelength-division-multiplexing and optical code-division
multiple-access (WDM/OCDMA) scheme are configured to meet the
various geographical locations requirement between optical network
unit (ONU) and optical line terminal (OLT). The AWG-base optical
switch is designed and viewed as central star-mesh topology to
prohibit/decrease the duplicated redundant elements such as fiber and
transceiver as well. Hence, by simple monitoring and routing switch
algorithm, random fault-recovery capacity is achieved over
bi-directional (up/downstream) WDM/OCDMA scheme. When error
of distribution fiber (DF) takes place or bit-error-rate (BER) is higher
than 10-9 requirement, the primary/slave AWG-based OSW are
adjusted and controlled dynamically to restore the affected ONU
groups via the other working DFs immediately.
Abstract: Stress Concentration Factors are significant in
machine design as it gives rise to localized stress when any change in
the design of surface or abrupt change in the cross section occurs.
Almost all machine components and structural members contain
some form of geometrical or microstructural discontinuities. These
discontinuities are very dangerous and lead to failure. So, it is very
much essential to analyze the stress concentration factors for critical
applications like Turbine Rotors. In this paper Finite Element
Analysis (FEA) with extremely fine mesh in the vicinity of the
blades of Steam Turbine Rotor is applied to determine stress
concentration factors. A model of Steam Turbine Rotor is shown in
Fig. 1.
Abstract: A novel design of two-wheeled robotic vehicle with moving payload is presented in this paper. A mathematical model describing the vehicle dynamics is derived and simulated in Matlab Simulink environment. Two control strategies were developed to stabilise the vehicle in the upright position. A robust Proportional- Integral-Derivative (PID) control strategy has been implemented and initially tested to measure the system performance, while the second control strategy is to use a hybrid fuzzy logic controller (FLC). The results are given on a comparative basis for the system performance in terms of disturbance rejection, control algorithms robustness as well as the control effort in terms of input torque.
Abstract: In this paper, linear multistep technique using power
series as the basis function is used to develop the block methods
which are suitable for generating direct solution of the special second
order ordinary differential equations of the form y′′ = f(x,y), a < = x < = b with associated initial or boundary conditions. The continuaous hybrid formulations enable us to differentiate and evaluate at some
grids and off – grid points to obtain two different three discrete
schemes, each of order (4,4,4)T, which were used in block form for
parallel or sequential solutions of the problems. The computational
burden and computer time wastage involved in the usual reduction of
second order problem into system of first order equations are avoided
by this approach. Furthermore, a stability analysis and efficiency of
the block method are tested on linear and non-linear ordinary
differential equations whose solutions are oscillatory or nearly
periodic in nature, and the results obtained compared favourably with
the exact solution.
Abstract: The work reported in this paper is motivated by the fact that there is a need to apply autonomic computing concepts to parallel computing systems. Advancing on prior work based on intelligent cores [36], a swarm-array computing approach, this paper focuses on 'Intelligent agents' another swarm-array computing approach in which the task to be executed on a parallel computing core is considered as a swarm of autonomous agents. A task is carried to a computing core by carrier agents and is seamlessly transferred between cores in the event of a predicted failure, thereby achieving self-ware objectives of autonomic computing. The feasibility of the proposed swarm-array computing approach is validated on a multi-agent simulator.
Abstract: Participation in global trade means that Chinas vegetables and fruits industry faces international food safety standards and increased scrutiny worldwide. The objectives of this paper were to investigate how existing food safety standards and regulations in the importing countries impact the export of vegetables and fruits from China. This paper discussed the current and historical situations of Chinas vegetables and fruits export from 1996 to 2010, analyzed the Maximum Residual Limit (MRL) standards of pesticides imposed by importing countries, quantitatively estimated the impacts of food safety standards on Chinas vegetables and fruits export based on a gravity model. The results showed that although transportation distance between trade partners and tariff rates on vegetables and fruits were still the importantly resistant factors for China export, vegetables and fruits export was sensitive to the number of regulated pesticides, the strictness, and the level of food safety standards imposed by importing countries, which showed a significant trade flow effect, stricter food safety standards, increased number of regulated pesticides significantly inhibit China export of vegetables and fruits. Moreover, Chinas food safety standards also showed a significantly effect on vegetables and fruits export, which inhibited export to some extent. KeywordsFood safety standards, MRL, Vegetables, Fruits, Export.
Abstract: In the present study, a steady-state simulation model
has been developed to evaluate the system performance of a
transcritical carbon dioxide heat pump system for simultaneous water
cooling and heating. Both the evaporator (including both two-phase
and superheated zone) and gas cooler models consider the highly
variable heat transfer characteristics of CO2 and pressure drop. The
numerical simulation model of transcritical CO2 heat pump has been
validated by test data obtained from experiments on the heat pump
prototype. Comparison between the test results and the model
prediction for system COP variation with compressor discharge
pressure shows a modest agreement with a maximum deviation of
15% and the trends are fairly similar. Comparison for other operating
parameters also shows fairly similar deviation between the test
results and the model prediction. Finally, the simulation results are
presented to study the effects of operating parameters such as,
temperature of heat exchanger fluid at the inlet, discharge pressure,
compressor speed on system performance of CO2 heat pump, suitable
in a dairy plant where simultaneous cooling at 4oC and heating at
73oC are required. Results show that good heat transfer properties of
CO2 for both two-phase and supercritical region and efficient
compression process contribute a lot for high system COPs.
Abstract: An effort estimation model is needed for softwareintensive
projects that consist of hardware, embedded software or
some combination of the two, as well as high level software
solutions. This paper first focuses on functional decomposition
techniques to measure functional complexity of a computer system
and investigates its impact on system development effort. Later, it
examines effects of technical difficulty and design team capability
factors in order to construct the best effort estimation model. With
using traditional regression analysis technique, the study develops a
system development effort estimation model which takes functional
complexity, technical difficulty and design team capability factors as
input parameters. Finally, the assumptions of the model are tested.
Abstract: In this paper, the Lennard -Jones potential is applied
to molecules of liquid argon as well as its vapor and platinum as solid
surface in order to perform a non-equilibrium molecular dynamics
simulation to study the microscopic aspects of liquid-vapor-solid
interactions. The channel is periodic in x and y directions and along z
direction it is bounded by atomic walls. It was found that density of
the liquids near the solid walls fluctuated greatly and that the
structure was more like a solid than a liquid. This indicates that the
interactions of solid and liquid molecules are very strong. The
resultant surface tension, liquid density and vapor density are found
to be well predicted when compared with the experimental data for
argon. Liquid and vapor densities were found to depend on the cutoff
radius which induces the use of P3M (particle-particle particle-mesh)
method which was implemented for evaluation of force and surface
tension.
Abstract: Research into the problem of classification of sonar signals has been taken up as a challenging task for the neural networks. This paper investigates the design of an optimal classifier using a Multi layer Perceptron Neural Network (MLP NN) and Support Vector Machines (SVM). Results obtained using sonar data sets suggest that SVM classifier perform well in comparison with well-known MLP NN classifier. An average classification accuracy of 91.974% is achieved with SVM classifier and 90.3609% with MLP NN classifier, on the test instances. The area under the Receiver Operating Characteristics (ROC) curve for the proposed SVM classifier on test data set is found as 0.981183, which is very close to unity and this clearly confirms the excellent quality of the proposed classifier. The SVM classifier employed in this paper is implemented using kernel Adatron algorithm is seen to be robust and relatively insensitive to the parameter initialization in comparison to MLP NN.
Abstract: Reliable information about tool temperature
distribution is of central importance in metal cutting. In this study,
tool-chip interface temperature was determined in cutting of ST37
steel workpiece by applying HSS as the cutting tool in dry turning.
Two different approaches were implemented for temperature
measuring: an embedded thermocouple (RTD) in to the cutting tool
and infrared (IR) camera. Comparisons are made between
experimental data and results of MSC.SuperForm and FLUENT
software.
An investigation of heat generation in cutting tool was performed
by varying cutting parameters at the stable cutting tool geometry and
results were saved in a computer; then the diagrams of tool
temperature vs. various cutting parameters were obtained. The
experimental results reveal that the main factors of the increasing
cutting temperature are cutting speed (V ), feed rate ( S ) and depth
of cut ( h ), respectively. It was also determined that simultaneously
change in cutting speed and feed rate has the maximum effect on
increasing cutting temperature.
Abstract: This paper presents a novel approach to finding a
priori interesting regions in mammograms. In order to delineate those
regions of interest (ROI-s) in mammograms, which appear to be
prominent, a topographic representation called the iso-level contour
map consisting of iso-level contours at multiple intensity levels and
region segmentation based-thresholding have been proposed. The
simulation results indicate that the computed boundary gives the
detection rate of 99.5% accuracy.
Abstract: this paper presented a survey analysis subjected on
network bandwidth management from published papers referred in
IEEE Explorer database in three years from 2009 to 2011. Network
Bandwidth Management is discussed in today-s issues for computer
engineering applications and systems. Detailed comparison is
presented between published papers to look further in the IP based
network critical research area for network bandwidth management.
Important information such as the network focus area, a few
modeling in the IP Based Network and filtering or scheduling used in
the network applications layer is presented. Many researches on
bandwidth management have been done in the broad network area
but fewer are done in IP Based network specifically at the
applications network layer. A few researches has contributed new
scheme or enhanced modeling but still the issue of bandwidth
management still arise at the applications network layer. This survey
is taken as a basic research towards implementations of network
bandwidth management technique, new framework model and
scheduling scheme or algorithm in an IP Based network which will
focus in a control bandwidth mechanism in prioritizing the network
traffic the applications layer.
Abstract: A common way to elude the signature-based Network Intrusion Detection System is based upon changing a recognizable attack to an unrecognizable one via the IDS. For example, in order to evade sign accommodation with intrusion detection system markers, a hacker spilt the payload packet into many small pieces or hides them within messages. In this paper we try to model the main fragmentation attack and create a new module in the intrusion detection architecture system which recognizes the main fragmentation attacks through verification of integrity checking of TCP packet in order to prevent elusion of the system and also to announce the necessary alert to the system administrator.
Abstract: This paper proposes a declarative language for
knowledge representation (Ibn Rochd), and its environment of
exploitation (DeGSE). This DeGSE system was designed and
developed to facilitate Ibn Rochd writing applications. The system
was tested on several knowledge bases by ascending complexity,
culminating in a system for recognition of a plant or a tree, and
advisors to purchase a car, for pedagogical and academic guidance,
or for bank savings and credit. Finally, the limits of the language and
research perspectives are stated.
Abstract: The most reliable and accurate description of the actual behavior of a software system is its source code. However, not all questions about the system can be answered directly by resorting to this repository of information. What the reverse engineering methodology aims at is the extraction of abstract, goal-oriented “views" of the system, able to summarize relevant properties of the computation performed by the program. While concentrating on reverse engineering we had modeled the C++ files by designing the translator.