Abstract: Combustion, emission and performance
characterization of a single cylinder diesel engine using methanol
diesel blends was carried out. The blends were 5% (v/v) methanol in
diesel (MD05) and 10% (v/v) methanol in diesel (MD10). The
problem of solubility of methanol and diesel was addressed by an
agitator placed inside the fuel tank to prevent phase separation. The
results indicated that total combustion duration was reduced by15.8%
for MD05 and 31.27% for MD10compared to the baseline data.
Ignition delay was increased with increasing methanol volume
fraction in the test fuel. Total cyclic heat release was reduced by
1.5% for MD05 and 6.7% for MD10 as compared to diesel baseline.
Emissions of carbon monoxide, hydrocarbons along with smoke were
reduced and that of nitrogen oxides were increased with rising
methanol contents in the test fuel. Full load brake thermal efficiency
was marginally reduced with increased methanol composition in the
blend.
Abstract: The present study was provided to examine the
vortical structures generated by two inclined impinging jets with
experimental and numerical investigations. The jets are issuing with a
pitch angle α=40° into a confined quiescent fluid. The experimental
investigation on flow patterns was visualized by using olive particles
injected into the jets illuminated by Nd:Yag laser light to reveal the
finer details of the confined jets interaction. It was observed that two
counter-rotating vortex pairs (CVPs) were generated in the near
region. A numerical investigation was also performed. First, the
numerical results were validates against the experimental results and
then the numerical model was used to study the effect of section ratio
on the evolution of the CVPs. Our results show promising agreement
with experimental data, and indicate that our model has the potential
to produce useful and accurate data regarding the evolution of CVPs.
Abstract: In this paper, multi-processors job shop scheduling problems are solved by a heuristic algorithm based on the hybrid of priority dispatching rules according to an ant colony optimization algorithm. The objective function is to minimize the makespan, i.e. total completion time, in which a simultanous presence of various kinds of ferons is allowed. By using the suitable hybrid of priority dispatching rules, the process of finding the best solution will be improved. Ant colony optimization algorithm, not only promote the ability of this proposed algorithm, but also decreases the total working time because of decreasing in setup times and modifying the working production line. Thus, the similar work has the same production lines. Other advantage of this algorithm is that the similar machines (not the same) can be considered. So, these machines are able to process a job with different processing and setup times. According to this capability and from this algorithm evaluation point of view, a number of test problems are solved and the associated results are analyzed. The results show a significant decrease in throughput time. It also shows that, this algorithm is able to recognize the bottleneck machine and to schedule jobs in an efficient way.
Abstract: Economic Load Dispatch (ELD) is a method of determining
the most efficient, low-cost and reliable operation of a power
system by dispatching available electricity generation resources to
supply load on the system. The primary objective of economic
dispatch is to minimize total cost of generation while honoring
operational constraints of available generation resources. In this paper
an intelligent water drop (IWD) algorithm has been proposed to
solve ELD problem with an objective of minimizing the total cost of
generation. Intelligent water drop algorithm is a swarm-based natureinspired
optimization algorithm, which has been inspired from natural
rivers. A natural river often finds good paths among lots of possible
paths in its ways from source to destination and finally find almost
optimal path to their destination. These ideas are embedded into
the proposed algorithm for solving economic load dispatch problem.
The main advantage of the proposed technique is easy is implement
and capable of finding feasible near global optimal solution with
less computational effort. In order to illustrate the effectiveness of
the proposed method, it has been tested on 6-unit and 20-unit test
systems with incremental fuel cost functions taking into account the
valve point-point loading effects. Numerical results shows that the
proposed method has good convergence property and better in quality
of solution than other algorithms reported in recent literature.
Abstract: We introduce a novel approach to measuring how
humans learn based on techniques from information theory and
apply it to the oriental game of Go. We show that the total amount
of information observable in human strategies, called the strategic
information, remains constant for populations of players of differing
skill levels for well studied patterns of play. This is despite the very
large amount of knowledge required to progress from the recreational
players at one end of our spectrum to the very best and most
experienced players in the world at the other and is in contrast to
the idea that having more knowledge might imply more 'certainty'
in what move to play next. We show this is true for very local
up to medium sized board patterns, across a variety of different
moves using 80,000 game records. Consequences for theoretical and
practical AI are outlined.
Abstract: Unsteady boundary layer flow of an incompressible
micropolar fluid over a stretching sheet when the sheet is stretched in
its own plane is studied in this paper. The stretching velocity is
assumed to vary linearly with the distance along the sheet. Two equal
and opposite forces are impulsively applied along the x-axis so that the
sheet is stretched, keeping the origin fixed in a micropolar fluid. The
transformed unsteady boundary layer equations are solved
numerically using the Keller-box method for the whole transient from
the initial state to final steady-state flow. Numerical results are
obtained for the velocity and microrotation distributions as well as the
skin friction coefficient for various values of the material parameter K.
It is found that there is a smooth transition from the small-time
solution to the large-time solution.
Abstract: This study aimed to explore future life orientation and
support that needed to accomplish it. A total of 258 participants are
Javanese high school student. The age of the sample ranges from 14
to 18 years old. Participants were asked about their future aspiration,
their reason of choosing them as important goals in their life, and
support that they need to accomplished their goals using open ended
questionnaire. The responses were categorized through content
analysis into four main categories. They are: (1) Self Fulfillment
(72.1%) (2) Parents and Family (16.7%) (3) Altruism (8.1%) (4)
Social and Economy Status (3.1%). Meanwhile, the categories for
support that they needed are shown as follows: (1) Affection Support
(64.7%) (2) Spiritual support (17.4%) (3) Material Support (10.9%)
(4) Guidance Support (7.0%). The research found that affection
support always gets the highest number in every future orientation
categories. It can be concluded that although Javanese adolescents
have different future orientation, they basically need affection
support.
Abstract: In this paper an ant colony optimization algorithm is
developed to solve the permutation flow shop scheduling problem. In
the permutation flow shop scheduling problem which has been vastly
studied in the literature, there are a set of m machines and a set of n
jobs. All the jobs are processed on all the machines and the sequence
of jobs being processed is the same on all the machines. Here this
problem is optimized considering two criteria, makespan and total
flow time. Then the results are compared with the ones obtained by
previously developed algorithms. Finally it is visible that our
proposed approach performs best among all other algorithms in the
literature.
Abstract: Tomato powder has good potential as substitute of tomato paste and other tomato products. In order to protect physicochemical properties and nutritional quality of tomato during dehydration process, investigation was carried out using different drying methods and pretreatments. Solar drier and continuous conveyor (tunnel) drier were used for dehydration where as calcium chloride (CaCl2), potassium metabisulphite (KMS), calcium chloride and potassium metabisulphite (CaCl2 +KMS), and sodium chloride (NaCl) selected for treatment.. lycopene content, dehydration ratio, rehydration ratio and non-enzymatic browning in addition to moisture, sugar and titrable acidity were studied. Results show that pre-treatment with CaCl2 and NaCl increased water removal and moisture mobility in tomato slices during drying of tomatoes. Where CaCl2 used along with KMS the NEB was recorded the least compared to other treatments and the best results were obtained while using the two chemicals in combination form. Storage studies in LDPE polymeric and metalized polyesters films showed less changes in the products packed in metallized polyester pouches and even after 6 months lycopene content did not decrease more than 20% as compared to the control sample and provide extension of shelf life in acceptable condition for 6 months. In most of the quality characteristics tunnel drier samples presented better values in comparison to solar drier.
Abstract: The aim of this study was to examine current levels of physical activity determined via heart rate monitoring. A total of 176 children (85 boys, 91 girls) aged 5-13 years wore sealed Polar heart rate monitors for at least 10 hours per day on at least 3 days. Mean daily minutes of moderate to vigorous-intensity physical activity was 65 ± 43 (mean ± SD) for boys and 54 ± 37 for girls. Daily minutes of vigorous-intensity activity was 31 ± 24 and 24 ± 21 for boys and girls respectively. Significant differences in physical activity levels were observed between school day and weekends, boys and girls, and among age and geographical groups. Only 36% of boys and 22% of girls met the New Zealand physical activity guideline. This research indicates that a large proportion of New Zealand children are not meeting physical activity recommendations.
Abstract: This essay endeavors to read Ama Ata Aidoo-s Our Sister Killjoy with a postocolonially-inflected consciousness. It aims at demonstrating how her work could be read as a sophisticated postcolonial revision of the colonial travel narrative whereby the protagonist-s black-eyed squint operates as 'the all-seeing-eye' to subvert the historically unbroken legacy of the Orientalist ideology. It tries to demonstrate how Sissie assumes authority and voice in an act that destabilizes the traditionally established modes of western representation. It is also an investigation into how Aidoo-s text adopts processes which disengage the Eurocentric view produced by the discursive itineraries of western institutions through diverse acts of resistance and 'various strategies of subversion and appropriation'. Her counter discursive strategies of resistance are shaped up in various ways by a feminist consciousness that attempts to articulate a distinct African version of identity and preserve cultural distinctiveness.
Abstract: The electrochemical coagulation of a kaolin
suspension was investigated at the currents of 0.06, 0.12, 0.22, 0.44,
0.85 A (corresponding to 0.68, 1.36, 2.50, 5.00, 9.66 mA·cm-2,
respectively) for the contact time of 5, 10, 20, 30, and 50 min. The
TSS removal efficiency at currents of 0.06 A, 0.12 A and 0.22 A
increased with the amount of iron generated by the sacrificial anode,
while the removal efficiencies did not increase proportionally with
the amount of iron generated at the currents of 0.44 and 0.85 A,
where electroflotation was clearly observed. Zeta potential
measurement illustrated the presence of the highly positive charged
particles created by sorption of highly charged polymeric metal
hydroxyl species onto the negative surface charged kaolin particles at
both low and high applied currents. The disappearance of the
individual peaks after certain contact times indicated the attraction
between these positive and negative charged particles causing
agglomeration. It was concluded that charge neutralization of the
individual species was not the only mechanism operating in the
electrocoagulation process at any current level, but electrostatic
attraction was likely to co-operate or mainly operate.
Abstract: A product development for green logistics model using
the fuzzy analytic network process method is presented for evaluating
the relationships among the product design, the manufacturing
activities, and the green supply chain. In the product development
stage, there can be alternative ways to design the detailed components
to satisfy the design concept and product requirement. In different
design alternative cases, the manufacturing activities can be different.
In addition, the manufacturing activities can affect the green supply
chain of the components and product. In this research, a fuzzy analytic
network process evaluation model is presented for evaluating the
criteria in product design, manufacturing activities, and green supply
chain. The comparison matrices for evaluating the criteria among the
three groups are established. The total relational values between the
three groups represent the relationships and effects. In application, the
total relational values can be used to evaluate the design alternative
cases for decision-making to select a suitable design case and the green
supply chain. In this presentation, an example product is illustrated. It
shows that the model is useful for integrated evaluation of design and
manufacturing and green supply chain for the purpose of product
development for green logistics.
Abstract: Cow milk, is a product of the mammary gland and
soymilk is a beverage made from soybeans; it is the liquid that
remains after soybeans are soaked. In this research effort, we
compared nutritional parameters of this two kind milk such as total
fat, fiber, protein, minerals (Ca, Fe and P), fatty acids, carbohydrate,
lactose, water, total solids, ash, pH, acidity and calories content in
one cup (245 g). Results showed soymilk contains 4.67 grams of fat,
0.52 of fatty acids, 3.18 of fiber, 6.73 of protein, 4.43 of
carbohydrate, 0.00 of lactose, 228.51 of water, 10.40 of total solids
and 0.66 of ash, also 9.80 milligrams of Ca, 1.42 of Fe, and 120.05 of
P, 79 Kcal of calories, pH=6.74 and acidity was 0.24%. Cow milk
contains 8.15 grams of fat, 5.07 of fatty acids, 0.00 of fiber, 8.02 of
protein, 11.37 of carbohydrate, ´Çá4.27 of lactose, 214.69 of water,
12.90 of total solids, 1.75 of ash, 290.36 milligrams of Ca, 0.12 of
Fe, and 226.92 of P, 150 Kcal of calories, pH=6.90 and acidity was
0.21% . Soy milk is one of plant-based complete proteins and cow
milk is a rich source of nutrients as well. Cow milk is containing near
twice as much fat as and ten times more fatty acids do soymilk. Cow
milk contains greater amounts of mineral (except Fe) it contain more
than three hundred times the amount of Ca and nearly twice the
amount of P as does soymilk but soymilk contains more Fe (ten time
more) than does cow milk. Cow milk and soy milk contain nearly
identical amounts of protein and water and fiber is a big plus, dairy
has none. Although what we choose to drink is really a mater of
personal preference and our health objectives but looking at the
comparison, soy looks like healthier choices.
Abstract: This paper deals with the problem of non-uniform
torsion in thin-walled elastic beams with asymmetric cross-section,
removing the basic concept of a fixed center of twist, necessary in the
Vlasov-s and Benscoter-s theories to obtain a warping stress field
equivalent to zero. In this new torsion/flexure theory, despite of the
classical ones, the warping function will punctually satisfy the first
indefinite equilibrium equation along the beam axis and it wont- be
necessary to introduce the classical congruence condition, to take into
account the effect of the beam restraints. The solution, based on the
Fourier development of the displacement field, is obtained assuming
that the applied external torque is constant along the beam axis and
on both beam ends the unit twist angle and the warping axial
displacement functions are totally restrained.
Finally, in order to verify the feasibility of the proposed method
and to compare it with the classical theories, two applications are
carried out. The first one, relative to an open profile, is necessary to
test the numerical method adopted to find the solution; the second
one, instead, is relative to a simplified containership section,
considered as full restrained in correspondence of two adjacent
transverse bulkheads.
Abstract: This research studied recycled waste by the Recyclable Material Bank Project of 4 universities in the central region of Thailand for the evaluation of reducing greenhouse gas emissions compared with landfilling activity during July 2012 to June 2013. The results showed that the projects collected total amount of recyclable wastes of about 911,984.80 kilograms. Office paper had the largest amount among these recycled wastes (50.68% of total recycled waste). Groups of recycled waste can be prioritized from high to low according to their amount as paper, plastic, glass, mixed recyclables, and metal, respectively. The project reduced greenhouse gas emissions equivalent to about 2814.969 metric tons of carbon dioxide. The most significant recycled waste that affects the reduction of greenhouse gas emissions is office paper which is 70.16% of total reduced greenhouse gasses emission. According to amount of reduced greenhouse gasses emission, groups of recycled waste can be prioritized from high to low significances as paper, plastic, metals, mixed recyclables, and glass, respectively.
Abstract: Surface sediment samples were collected from the
Canon River mouth, Taiwan and analyzed for polycyclic aromatic
hydrocarbons (PAHs). Total PAHs concentrations varied from 337 to
1,252 ng/g dry weight, with a mean concentration of 827 ng/g dry
weight. The spatial distribution of PAHs reveals that the PAHs
concentration is relatively high in the river mouth region, and
gradually diminishes toward the harbor region. Diagnostic ratios
showed that the possible source of PAHs in the Canon River mouth
could be petroleum combustion. The toxic equivalent concentrations
(TEQcarc) of PAHs varied from 47 to 112 ng TEQ/g dry weight. Higher
total TEQcarc values were found in the river mouth region. As
compared with the US Sediment Quality Guidelines (SQGs), the
observed levels of PAHs at Canon River mouth were lower than the
effects range low (ERL), and would probably not exert adverse
biological effects.
Abstract: Toxic and bloom-forming cyanobacterium Microcystis
aeruginosa was exposed to antialgal allelochemical gramine (0, 0.5, 1,
2, 4, 8 mg·L-1), The effects of gramine on photosynthetic pigments
(lipid soluble: chlorophyll a and β-carotene; water soluble:
phycocyanin, allophycocyanin, phycoerythrin, and total phycobilins)
and absorption spectra were studied in order to identify the most
sensitive pigment probe implicating the crucial suppression site on
photosynthetic apparatus. The results obtained indicated that all
pigment parameters were decreased with gramine concentration
increasing and exposure time extending. The above serious bleaching
of pigments was also reflected on the scanning results of absorption
spectra. Phycoerytherin exhibited the highest sensitivity to gramine
added, following by the largest relative decrease. It was concluded that
gramine seriously influenced algal photosynthetic activity by
destroying photosynthetic pigments and phycoerythrin most sensitive
to gramine might be contributed to its placing the outside of
phycobilins.
Abstract: Power Factor (PF) is one of the most important parameters in the electrical systems, especially in the water pumping station. The low power factor value of the water pumping stations causes penalty for the electrical bill. There are many methods use for power factor improvement. Each one of them uses a capacitor on the electrical power network. The position of the capacitors is varied depends on many factors such as; voltage level and capacitors rating. Adding capacitors on the motor terminals increase the supply power factor from 0.8 to more than 0.9 but these capacitors cause some problems for the electrical grid network, such as increasing the harmonic contents of the grid line voltage. In this paper the effects of using capacitors in the water pumping stations to improve the power factor value on the harmonic contents of the electrical grid network are studied. One of large water pumping stations in Kafr El-Shikh Governorate in Egypt was used, as a case study. The effect of capacitors on the line voltage harmonic contents is measured. The station uses capacitors to improve the PF values at the 1 lkv grid network. The power supply harmonics values are measured by a power quality analyzer at different loading conditions. The results showed that; the capacitors improved the power factor value of the feeder and its value increased than 0.9. But the THD values are increased by adding these capacitors. The harmonic analysis showed that; the 13th, 17th, and 19th harmonics orders are increased also by adding the capacitors.
Abstract: The work presents a development of EN338 strength classes for Strombosia pustulata, Pterygotama crocarpa, Nauclea diderrichii and Entandrophragma cyclindricum Nigerian timber species. The specimens for experimental measurements were obtained from the timber-shed at the famous Panteka market in Kaduna in the northern part of Nigeria. Laboratory experiments were conducted to determine the physical and mechanical properties of the selected timber species in accordance with EN 13183-1 and ASTM D193. The mechanical properties were determined using three point bending test. The generated properties were used to obtain the characteristic values of the material properties in accordance with EN384. The selected timber species were then classified according to EN 338. Strombosia pustulata, Pterygotama crocarpa, Nauclea diderrichii and Entandrophragma cyclindricum were assigned to strength classes D40, C14, D40 and D24 respectively. Other properties such as tensile and compressive strengths parallel and perpendicular to grains, shear strength as well as shear modulus were obtained in accordance with EN 338.