Abstract: Inorganic nanoparticles filled polymer composites
have extended their multiple functionalities to various applications,
including mechanical reinforcement, gas barrier, dimensional
stability, heat distortion temperature, flame-retardant, and thermal
conductivity. Sodium stearate-modified calcium carbonate (CaCO3)
nanoparticles were prepared using surface modification method. The
results showed that sodium stearate attached to the surface of CaCO3
nanoparticles with the chemical bond. The effect of modified CaCO3
nanoparticles on thermal properties of polypropylene (PP) was
studied by means of differential scanning calorimetry (DSC) and
Thermogravimetric analysis (TGA). It was found that CaCO3
significantly affected the crystallization temperature and
crystallization degree of PP. Effect of the modified CaCO3 content on
mechanical properties of PP/CaCO3 nanocomposites was also
studied. The results showed that the modified CaCO3 can effectively
improve the mechanical properties of PP. In comparison with PP, the
impact strength of PP/CaCO3 nanocomposites increased by about
65% and the hardness increased by about 5%.
Abstract: Concrete strength evaluated from compression tests
on cores is affected by several factors causing differences from the
in-situ strength at the location from which the core specimen was
extracted. Among the factors, there is the damage possibly occurring
during the drilling phase that generally leads to underestimate the
actual in-situ strength. In order to quantify this effect, in this study
two wide datasets have been examined, including: (i) about 500 core
specimens extracted from Reinforced Concrete existing structures,
and (ii) about 600 cube specimens taken during the construction of
new structures in the framework of routine acceptance control. The
two experimental datasets have been compared in terms of
compression strength and specific weight values, accounting for the
main factors affecting a concrete property, that is type and amount of
cement, aggregates' grading, type and maximum size of aggregates,
water/cement ratio, placing and curing modality, concrete age. The
results show that the magnitude of the strength reduction due to
drilling damage is strongly affected by the actual properties of
concrete, being inversely proportional to its strength. Therefore, the
application of a single value of the correction coefficient, as generally
suggested in the technical literature and in structural codes, appears
inappropriate. A set of values of the drilling damage coefficient is
suggested as a function of the strength obtained from compressive
tests on cores.
Abstract: Let X be a connected space, X be a space, let p : X -→ X be a continuous map and let (X, p) be a covering space of X. In the first section we give some preliminaries from covering spaces and their automorphism groups. In the second section we derive some algebraic properties of both universal and regular covering spaces (X, p) of X and also their automorphism groups A(X, p).
Abstract: Intermetallic Ni3Al – based alloys belong to a group
of advanced materials characterized by good chemical and physical
properties (such as structural stability, corrosion resistance) which
offer advenced technological applications. The paper presents the
study of catalytic properties of Ni3Al foils (thickness approximately
50 &m) in the methanol and hexane decomposition. The egzamined
material posses microcrystalline structure without any additional
catalysts on the surface. The better catalytic activity of Ni3Al foils
with respect to quartz plates in both methanol and hexane
decomposition was confirmed. On thin Ni3Al foils the methanol
conversion reaches approximately 100% above 480 oC while the
hexane conversion reaches approximately 100% (98,5%) at 500 oC.
Deposit formed during the methanol decomposition is built up of
carbon nanofibers decorated with metal-like nanoparticles.
Abstract: Nanophotocatalysts such as titanium (TiO2), zinc (ZnO), and iron (Fe2O3) oxides can be used in organic pollutants oxidation, and in many other applications. But among the challenges for technological application (scale-up) of the nanotechnology scientific developments two aspects are still little explored: research on environmental risk of the nanomaterials preparation methods, and the study of nanomaterials properties and/or performance variability. The environmental analysis was performed for six different methods of ZnO nanoparticles synthesis, and showed that it is possible to identify the more environmentally compatible process even at laboratory scale research. The obtained ZnO nanoparticles were tested as photocatalysts, and increased the degradation rate of the Rhodamine B dye up to 30 times.
Abstract: The performance and complexity of QoS routing depends on the complex interaction between a large set of parameters. This paper investigated the scaling properties of source-directed link-state routing in large core networks. The simulation results show that the routing algorithm, network topology, and link cost function each have a significant impact on the probability of successfully routing new connections. The experiments confirm and extend the findings of other studies, and also lend new insight designing efficient quality-of-service routing policies in large networks.
Abstract: The research object was wheat bread. Experiments
were carried out at the Faculty of Food Technology of the Latvia
University of Agriculture. An active packaging in combination with
modified atmosphere (MAP, CO2 60% and N2 40%) was examined
and compared with traditional packaging in air ambiance. Polymer
Multibarrier 60, PP and OPP bags were used. Influence of iron based
oxygen absorber in sachets of 100 cc obtained from Mitsubishi Gas
Chemical Europe Ageless® was tested on the quality during the shelf
of wheat bread. Samples of 40±4 g were packaged in polymer
pouches (110 mm x 120 mm), hermetically sealed by MULTIVAC
C300 vacuum chamber machine, and stored in room temperature
+21.0±0.5 °C. The physiochemical properties – weight losses,
moisture content, hardness, pH, colour, changes of atmosphere
content (CO2 and O2) in headspace of packs, and microbial
conditions were analysed before packaging and in the 7th, 14th, 21st
and 28th days of storage.
Abstract: A novel thermo-sensitive superabsorbent hydrogel
with salt- and pH-responsiveness properties was obtained by grafting
of mixtures of acrylic acid (AA) and N-isopropylacrylamide
(NIPAM) monomers onto kappa-carrageenan, kC, using ammonium
persulfate (APS) as a free radical initiator in the presence of
methylene bisacrylamide (MBA) as a crosslinker. Infrared
spectroscopy was carried out to confirm the chemical structure of the
hydrogel. Moreover, morphology of the samples was examined by
scanning electron microscopy (SEM). The effect of MBA
concentration and AA/NIPAM weight ratio on the water absorbency
capacity has been investigated. The swelling variations of hydrogels
were explained according to swelling theory based on the hydrogel
chemical structure. The hydrogels exhibited salt-sensitivity and
cation exchange properties. The temperature- and pH-reversibility
properties of the hydrogels make the intelligent polymers as good
candidates for considering as potential carriers for bioactive agents,
e.g. drugs.
Abstract: Transesterification of candlenut (aleurites moluccana)
oil with methanol using potassium hydroxide as catalyst was
studied. The objective of the present investigation was to produce
the methyl ester for use as biodiesel. The operation variables
employed were methanol to oil molar ratio (3:1 – 9:1), catalyst
concentration (0.50 – 1.5 %) and temperature (303 – 343K). Oil
volume of 150 mL, reaction time of 75 min were fixed as common
parameters in all the experiments. The concentration of methyl ester
was evaluated by mass balance of free glycerol formed which was
analyzed by using periodic acid. The optimal triglyceride conversion
was attained by using methanol to oil ratio of 6:1, potassium
hydroxide as catalyst was of 1%, at room temperature. Methyl ester
formed was characterized by its density, viscosity, cloud and pour
points. The biodiesel properties had properties similar to those of
diesel oil, except for the viscosity that was higher.
Abstract: In Peer-to-Peer service networks, where peers offer any kind of publicly available services or applications, intuitive navigation through all services in the network becomes more difficult as the number of services increases. In this article, a concept is discussed that enables users to intuitively browse and use large scale P2P service networks. The concept extends the idea of creating virtual 3D-environments solely based on Peer-to-Peer technologies. Aside from browsing, users shall have the possibility to emphasize services of interest using their own semantic criteria. The appearance of the virtual world shall intuitively reflect network properties that may be of interest for the user. Additionally, the concept comprises options for load- and traffic-balancing. In this article, the requirements concerning the underlying infrastructure and the graphical user interface are defined. First impressions of the appearance of future systems are presented and the next steps towards a prototypical implementation are discussed.
Abstract: The recycling of concrete, bricks and masonry rubble
as concrete aggregates is an important way to contribute to a
sustainable material flow. However, there are still various
uncertainties limiting the widespread use of Recycled Concrete
Aggregates (RCA). The fluctuations in the composition of grade
recycled aggregates and their influence on the properties of fresh and
hardened concrete are of particular concern regarding the use of
RCA. Most of problems occurring while using recycled concrete
aggregates as aggregates are due to higher porosity and hence higher
water absorption, lower mechanical strengths, residual impurities on
the surface of the RCA forming weaker bond between cement paste
and aggregate. So, the reuse of RCA is still limited. Efficient
polymer based treatment is proposed in order to reuse RCA easier.
The silicon-based polymer treatments of RCA were carried out and
were compared. This kind of treatment can improve the properties of
RCA such as the rate of water absorption on treated RCA is
significantly reduced.
Abstract: This paper reports the evolving properties of a 3 mm low carbon steel plate after Laser Beam Forming achieve this objective, the chemical analyse material and the formed components were carried thereafter both were characterized through microhardness profiling microstructural evaluation and tensile testing. showed an increase in the elemental concentration of the component when compared to the as received attributed to the enhancement property of the LBF process Ultimate Tensile Strength (UTS) and the Vickers the formed component shows an increase when compared to the as received material, this was attributed to strain hardening and grain refinement brought about by the LBF process. The microstructure of the as received steel consists of equiaxed ferrit that of the formed component exhibits elongated orming process (LBF). To es of the as received out and compared; profiling, The chemical analyses formed material; this can be process. The microhardness of ferrite and pearlite while grains.
Abstract: The aim of this research was to calculate the thermal
properties of Au3Ni Nanowire. The molecular dynamics (MD)
simulation technique was used to obtain the effect of radius size on
the energy, the melting temperature and the latent heat of fusion at
the isobaric-isothermal (NPT) ensemble. The Quantum Sutton-Chen
(Q-SC) many body interatomic potentials energy have been used for
Gold (Au) and Nickel (Ni) elements and a mixing rule has been
devised to obtain the parameters of these potentials for nanowire
stats. Our MD simulation results show the melting temperature and
latent heat of fusion increase upon increasing diameter of nanowire.
Moreover, the cohesive energy decreased with increasing diameter of
nanowire.
Abstract: The electrical and structural properties of Hf/Al/Ni/Au
(20/100/25/50 nm) ohmic contact to n-GaN are reported in this study.
Specific contact resistivities of Hf/Al/Ni/Au based contacts have been
investigated as a function of annealing temperature and achieve the
lowest value of 1.09´10-6 Ω·cm2 after annealing at 650 oC in vacuum.
A detailed mechanism of ohmic contact formation is discussed. By
using different chemical analyses, it is anticipated that the formation of
Hf-Al-N alloy might be responsible to form low temperature ohmic
contacts for the Hf-based scheme to n-GaN.
Abstract: Subgrade moisture content varies with environmental and soil conditions and has significant influence on pavement performance. Therefore, it is important to establish realistic estimates of expected subgrade moisture contents to account for the effects of this variable on predicted pavement performance during the design stage properly. The initial boundary soil suction profile for a given pavement is a critical factor in determining expected moisture variations in the subgrade for given pavement and climatic and soil conditions. Several numerical models have been developed for predicting water and solute transport in saturated and unsaturated subgrade soils. Soil hydraulic properties are required for quantitatively describing water and chemical transport processes in soils by the numerical models. The required hydraulic properties are hydraulic conductivity, water diffusivity, and specific water capacity. The objective of this paper was to determine isothermal moisture profiles in a soil fill and predict the soil moisture movement above the ground water table using a simple one-dimensional finite difference model.
Abstract: The production of devices in nanoscale with specific
molecular rectifying function is one of the most significant goals in
state-of-art technology. In this work we show by ab initio quantum
mechanics calculations coupled with non-equilibrium Green
function, the design of an organic two-terminal device. These
molecular structures have molecular source and drain with several
bridge length (from five up to 11 double bonds). Our results are
consistent with significant features as a molecular rectifier and can be
raised up as: (a) it can be used as bi-directional symmetrical rectifier;
(b) two devices integrated in one (FET with one operational region,
and Thyristor thiristor); (c) Inherent stability due small intrinsic
capacitance under forward/reverse bias. We utilize a scheme for the
transport mechanism based on previous properties of ¤Ç bonds type
that can be successfully utilized to construct organic nanodevices.
Abstract: The amplitude response of infrared (IR) sensors
depends on the reflectance properties of the target. Therefore, in
order to use IR sensor for measuring distances accurately, prior
knowledge of the surface must be known. This paper describes the
Phong Illumination Model for determining the properties of a surface
and subsequently calculating the distance to the surface. The angular
position of the IR sensor is computed as normal to the surface for
simplifying the calculation. Ultrasonic (US) sensor can provide the
initial information on distance to obtain the parameters for this
method. In addition, the experimental results obtained by using
LabView are discussed. More care should be taken when placing the
objects from the sensors during acquiring data since the small change
in angle could show very different distance than the actual one.
Since stereo camera vision systems do not perform well under some
environmental conditions such as plain wall, glass surfaces, or poor
lighting conditions, the IR and US sensors can be used additionally to
improve the overall vision systems of mobile robots.
Abstract: Nowadays, the performance required for concrete
structures is more complicated and diversified. Self-compacting
concrete is a fluid mixture suitable for placing in structures with
congested reinforcement without vibration. Self-compacting concrete
development must ensure a good balance between deformability and
stability. Also, compatibility is affected by the characteristics of
materials and the mix proportions; it becomes necessary to evolve a
procedure for mix design of SCC.
This paper presents an experimental procedure for the design of
self-compacting concrete mixes with different water-cement ratios
(w/c) and other constant ratios by local materials. The test results for
acceptance characteristics of self-compacting concrete such as slump
flow, V-funnel and L-Box are presented. Further, compressive
strength, tensile strength and modulus of elasticity of specimens were
also determined and results are included here
Abstract: Renewable natural fibres such as oil palm, flax, and
pineapple leaf can be utilized to obtain new high performance
polymer materials. The reuse of waste natural fibres as reinforcement
for polymer is a sustainable option to the environment. However, due
to its high hydroxyl content of cellulose, natural fibres are
susceptible to absorb water that affects the composite mechanical
properties adversely. Research found that Nano materials such as
Nano Silica Carbide (n-SiC) and Nano Clay can be added into the
polymer composite to overcome this problem by enhancing its
mechanical properties in wet condition. The addition of Nano
material improves the tensile and wear properties, flexural stressstrain
behaviour, fracture toughness, and fracture strength of polymer
natural composites in wet and dry conditions.
Abstract: This paper presents the experimental results of
comparison between leakage currents and discharge currents. The leakage currents were obtained on polluted porcelain insulator.
Whereas, the discharge currents were obtained on lightly artificial
polluted porcelain specimen. The conducted measurements were
leakage current or discharge current and applied voltage. The insulator or specimen was in a hermetically sealed chamber, and the
current waveforms were analyzed using FFT.
The result indicated that the leakage current (LC) on low RH condition the fifth harmonic would be visible, and followed by the
seventh harmonic. The insulator had capacitive property. Otherwise,
on 99% relative humidity, the fifth harmonic would also be visible,
and the phase angle reached up to 12.2 degree. Whereas, on discharge current, the third harmonic would be visible, and followed
by fifth harmonic. The third harmonic would increase as pressure reduced. On this condition, the specimen had a non-linear characteristics