Abstract: The Lattice Boltzmann Method (LBM) with double populations is applied to solve the steady-state laminar natural convective heat transfer in a triangular cavity filled with water. The bottom wall is heated, the vertical wall is cooled, and the inclined wall is kept adiabatic. The buoyancy effect was modeled by applying the Boussinesq approximation to the momentum equation. The fluid velocity is determined by D2Q9 LBM and the energy equation is discritized by D2Q4 LBM to compute the temperature field. Comparisons with previously published work are performed and found to be in excellent agreement. Numerical results are obtained for a wide range of parameters: the Rayleigh number from to and the inclination angle from 0° to 360°. Flow and thermal fields were exhibited by means of streamlines and isotherms. It is observed that inclination angle can be used as a relevant parameter to control heat transfer in right-angled triangular enclosures.
Abstract: Nowadays, we are facing with network threats that
cause enormous damage to the Internet community day by day. In
this situation, more and more people try to prevent their network
security using some traditional mechanisms including firewall,
Intrusion Detection System, etc. Among them honeypot is a versatile
tool for a security practitioner, of course, they are tools that are meant
to be attacked or interacted with to more information about attackers,
their motives and tools. In this paper, we will describe usefulness of
low-interaction honeypot and high-interaction honeypot and
comparison between them. And then we propose hybrid honeypot
architecture that combines low and high -interaction honeypot to
mitigate the drawback. In this architecture, low-interaction honeypot
is used as a traffic filter. Activities like port scanning can be
effectively detected by low-interaction honeypot and stop there.
Traffic that cannot be handled by low-interaction honeypot is handed
over to high-interaction honeypot. In this case, low-interaction
honeypot is used as proxy whereas high-interaction honeypot offers
the optimal level realism. To prevent the high-interaction honeypot
from infections, containment environment (VMware) is used.
Abstract: Knowledge about the magnetic quantities in a magnetic circuit is always of great interest. On the one hand, this information is needed for the simulation of a transformer. On the other hand, parameter studies are more reliable, if the magnetic quantities are derived from a well established model. One possibility to model the 3-phase transformer is by using a magnetic equivalent circuit (MEC). Though this is a well known system, it is often not an easy task to set up such a model for a large number of lumped elements which additionally includes the nonlinear characteristic of the magnetic material. Here we show the setup of a solver for a MEC and the results of the calculation in comparison to measurements taken. The equations of the MEC are based on a rearranged system of the nodal analysis. Thus it is possible to achieve a minimum number of equations, and a clear and simple structure. Hence, it is uncomplicated in its handling and it supports the iteration process. Additional helpful tasks are implemented within the solver to enhance the performance. The electric circuit is described by an electric equivalent circuit (EEC). Our results for the 3-phase transformer demonstrate the computational efficiency of the solver, and show the benefit of the application of a MEC.
Abstract: The main focus of this paper is on the human induced
forces. Almost all existing force models for this type of load (defined
either in the time or frequency domain) are developed from the
assumption of perfect periodicity of the force and are based on force
measurements conducted on rigid (i.e. high frequency) surfaces. To
verify the different authors conclusions the vertical pressure
measurements invoked during the walking was performed, using
pressure gauges in various configurations. The obtained forces are
analyzed using Fourier transformation. This load is often decisive in
the design of footbridges. Design criteria and load models proposed
by widely used standards and other researchers were introduced and a
comparison was made.
Abstract: The simulation of extrusion process is studied widely
in order to both increase products and improve quality, with broad
application in wire coating. The annular tube-tooling extrusion was
set up by a model that is termed as Navier-Stokes equation in
addition to a rheological model of differential form based on singlemode
exponential Phan-Thien/Tanner constitutive equation in a twodimensional
cylindrical coordinate system for predicting the
contraction point of the polymer melt beyond the die. Numerical
solutions are sought through semi-implicit Taylor-Galerkin pressurecorrection
finite element scheme. The investigation was focused on
incompressible creeping flow with long relaxation time in terms of
Weissenberg numbers up to 200. The isothermal case was considered
with surface tension effect on free surface in extrudate flow and no
slip at die wall. The Stream Line Upwind Petrov-Galerkin has been
proposed to stabilize solution. The structure of mesh after die exit
was adjusted following prediction of both top and bottom free
surfaces so as to keep the location of contraction point around one
unit length which is close to experimental results. The simulation of
extrusion process is studied widely in order to both increase products
and improve quality, with broad application in wire coating. The
annular tube-tooling extrusion was set up by a model that is termed
as Navier-Stokes equation in addition to a rheological model of
differential form based on single-mode exponential Phan-
Thien/Tanner constitutive equation in a two-dimensional cylindrical
coordinate system for predicting the contraction point of the polymer
melt beyond the die. Numerical solutions are sought through semiimplicit
Taylor-Galerkin pressure-correction finite element scheme.
The investigation was focused on incompressible creeping flow with
long relaxation time in terms of Weissenberg numbers up to 200. The
isothermal case was considered with surface tension effect on free
surface in extrudate flow and no slip at die wall. The Stream Line
Upwind Petrov-Galerkin has been proposed to stabilize solution. The
structure of mesh after die exit was adjusted following prediction of
both top and bottom free surfaces so as to keep the location of
contraction point around one unit length which is close to
experimental results.
Abstract: Proteins or genes that have similar sequences are likely to perform the same function. One of the most widely used techniques for sequence comparison is sequence alignment. Sequence alignment allows mismatches and insertion/deletion, which represents biological mutations. Sequence alignment is usually performed only on two sequences. Multiple sequence alignment, is a natural extension of two-sequence alignment. In multiple sequence alignment, the emphasis is to find optimal alignment for a group of sequences. Several applicable techniques were observed in this research, from traditional method such as dynamic programming to the extend of widely used stochastic optimization method such as Genetic Algorithms (GAs) and Simulated Annealing. A framework with combination of Genetic Algorithm and Simulated Annealing is presented to solve Multiple Sequence Alignment problem. The Genetic Algorithm phase will try to find new region of solution while Simulated Annealing can be considered as an alignment improver for any near optimal solution produced by GAs.
Abstract: The psychological well-being of a family is a subjective matter for evaluation, all the more when it involves the element of religions, whether Islam, Christianity, Buddhism or Hinduism. Each of these religions emphasises similar values and morals on family psychological well-being. This comparative study is specifically to determine the role of religion on family psychological well-being in Pekan district, Pahang, Malaysia. The study adopts a quantitative and qualitative mixed method design and considers a total of 412 samples of parents and children for the quantitative study, and 21 samples for the qualitative study. The quantitative study uses simple random sampling, whereas the qualitative sampling is purposive. The instrument for quantitative study is Ryff’s Psychological Well-being Scale and the qualitative study involves the construction of a guidelines protocol for in-depth interviews of respondents. The quantitative study uses the SPSS version .19 with One Way Anova, and the qualitative analysis is manual based on transcripts with specific codes and themes. The results show nonsignificance, that is, no significant difference among religions in all family psychological well-being constructs in the comparison of Islam, Christianity, Buddhism and Hinduism, thereby accepting a null hypothesis and rejecting an alternative hypothesis. The qualitative study supports the quantitative study, that is, all 21 respondents explain that no difference exists in psychological wellbeing in the comparison of teachings in all the religious mentioned. These implications may be used as guidelines for government and non-government bodies in considering religion as an important element in family psychological well-being in the long run.
Abstract: The effects of irrigation with dairy factory wastewater on soil properties were investigated at two sites that had received irrigation for > 60 years. Two adjoining paired sites that had never received DFE were also sampled as well as another seven fields from a wider area around the factory. In comparison with paired sites that had not received effluent, long-term wastewater irrigation resulted in an increase in pH, EC, extractable P, exchangeable Na and K and ESP. These changes were related to the use of phosphoric acid, NaOH and KOH as cleaning agents in the factory. Soil organic C content was unaffected by DFE irrigation but the size (microbial biomass C and N) and activity (basal respiration) of the soil microbial community were increased. These increases were attributed to regular inputs of soluble C (e.g. lactose) present as milk residues in the wastewater. Principal component analysis (PCA) of the soils data from all 11sites confirmed that the main effects of DFE irrigation were an increase in exchangeable Na, extractable P and microbial biomass C, an accumulation of soluble salts and a liming effect. PCA analysis of soil bacterial community structure, using PCR-DGGE of 16S rDNA fragments, generally separated individual sites from one another but did not group them according to irrigation history. Thus, whilst the size and activity of the soil microbial community were increased, the structure and diversity of the bacterial community remained unaffected.
Abstract: The equations governing the flow of an electrically conducting, incompressible viscous fluid over an infinite flat plate in the presence of a magnetic field are investigated using the homotopy perturbation method (HPM) with Padé approximants (PA) and 4th order Runge–Kutta method (4RKM). Approximate analytical and numerical solutions for the velocity field and heat transfer are obtained and compared with each other, showing excellent agreement. The effects of the magnetic parameter and Prandtl number on velocity field, shear stress, temperature and heat transfer are discussed as well.
Abstract: This paper addresses the design of predictive
networked controller with adaptation of a communication delay. The
networked control system contains random delays from sensor to
controller and from controller to actuator. The proposed predictive
controller includes an adaptation loop which decreases the influence
of communication delay on the control performance. Also, the
predictive controller contains a filter which improves the robustness
of the control system. The performance of the proposed adaptive
predictive controller is demonstrated by simulation results in
comparison with PI controller and predictive controller with constant
delay.
Abstract: Diabetes Mellitus is a chronic metabolic disorder, where the improper management of the blood glucose level in the diabetic patients will lead to the risk of heart attack, kidney disease and renal failure. This paper attempts to enhance the diagnostic accuracy of the advancing blood glucose levels of the diabetic patients, by combining principal component analysis and wavelet neural network. The proposed system makes separate blood glucose prediction in the morning, afternoon, evening and night intervals, using dataset from one patient covering a period of 77 days. Comparisons of the diagnostic accuracy with other neural network models, which use the same dataset are made. The comparison results showed overall improved accuracy, which indicates the effectiveness of this proposed system.
Abstract: When the characteristic length of an elastic solid is
down to the nanometer level, its deformation behavior becomes size
dependent. Surface energy /surface stress have recently been applied
to explain such dependency. In this paper, the effect of
strain-independent surface stress on the deformation of an isotropic
elastic solid containing a nanosized elliptical hole is studied by the
finite element method. Two loading cases are considered, in the first
case, hoop stress along the rim of the elliptical hole induced by pure
surface stress is studied, in the second case, hoop stress around the
elliptical opening under combined remote tension and surface stress is
investigated. It has been shown that positive surface stress induces
compressive hoop stress along the hole, and negative surface stress has
opposite effect, maximum hoop stress occurs near the major semi-axes
of the ellipse. Under combined loading of remote tension and surface
stress, stress concentration around the hole can be either intensified or
weakened depending on the sign of the surface stress.
Abstract: This paper deals with the optimal design of two-channel recursive parallelogram quadrature mirror filter (PQMF) banks. The analysis and synthesis filters of the PQMF bank are composed of two-dimensional (2-D) recursive digital all-pass filters (DAFs) with nonsymmetric half-plane (NSHP) support region. The design problem can be facilitated by using the 2-D doubly complementary half-band (DC-HB) property possessed by the analysis and synthesis filters. For finding the coefficients of the 2-D recursive NSHP DAFs, we appropriately formulate the design problem to result in an optimization problem that can be solved by using a weighted least-squares (WLS) algorithm in the minimax (L∞) optimal sense. The designed 2-D recursive PQMF bank achieves perfect magnitude response and possesses satisfactory phase response without requiring extra phase equalizer. Simulation results are also provided for illustration and comparison.
Abstract: Environmental decision making, particularly about
hazardous waste management, is inherently exposed to a high
potential conflict, principally because of the trade-off between sociopolitical,
environmental, health and economic factors. The need to
plan complex contexts has led to an increasing request for decision
analytic techniques as support for the decision process. In this work,
alternative systems of asbestos-containing waste management
(ACW) in Puglia (Southern Italy) were explored by a multi-criteria
decision analysis. In particular, through Analytic Hierarchy Process
five alternatives management have been compared and ranked
according to their performance and efficiency, taking into account
environmental, health and socio-economic aspects. A separated
valuation has been performed for different temporal scale. For short
period results showed a narrow deviation between the disposal
alternatives “mono-material landfill in public quarry" and “dedicate
cells in existing landfill", with the best performance of the first one.
While for long period “treatment plant to eliminate hazard from
asbestos-containing waste" was prevalent, although high energy
demand required to achieve the change of crystalline structure. A
comparison with results from a participative approach in valuation
process might be considered as future development of method
application to ACW management.
Abstract: In this work, we try to find the best setting
of Computational Fluid Dynamic solver available for the problems in
the field of supersonic internal flows. We used the supersonic air-toair
ejector to represent the typical problem in focus. There are
multiple oblique shock waves, shear layers, boundary layers
and normal shock interacting in the supersonic ejector making this
device typical in field of supersonic inner flows. Modeling of shocks
in general is demanding on the physical model of fluid, because
ordinary conservation equation does not conform to real conditions in
the near-shock region as found in many works. From these reasons,
we decided to take special care about solver setting in this article by
means of experimental approach of color Schlieren pictures and
pneumatic measurement. Fast pressure transducers were used to
measure unsteady static pressure in regimes with normal shock in
mixing chamber. Physical behavior of ejector in several regimes is
discussed. Best choice of eddy-viscosity setting is discussed on the
theoretical base. The final verification of the k-ω SST is done on the
base of comparison between experiment and numerical results.
Abstract: With the fast progression of data exchange in electronic way, information security is becoming more important in data storage and transmission. Because of widely using images in industrial process, it is important to protect the confidential image data from unauthorized access. In this paper, we analyzed current image encryption algorithms and compression is added for two of them (Mirror-like image encryption and Visual Cryptography). Implementations of these two algorithms have been realized for experimental purposes. The results of analysis are given in this paper.
Abstract: The main objective of this work is to compare the
quality of service of the bus companies operating in the city of Rio
Branco, located in the state of Acre with the quality of service of the
bus companies operating in the city of Campos, situated in the state
of Rio de Janeiro, both cities in Brazil. This comparison, based on the
opinion of the bus users, will determine their degree of satisfaction
with the service available in both cities. The outcome of this
evaluation shows the users unhappy with the quality of the service
provided by the bus companies operating in both cities and the need
to identify alternative solutions that may minimize the consequences
caused by the main problems detected in this work. With these
alternatives available, the bus companies will be able to better
understand the needs of their customers in terms of manpower,
service cost, time schedule, etc.
Abstract: Computational simulation of steam flow and heat transfer in power plant condensers on the basis of the threedimensional mathematical model for the flow through porous media is presented. In order to solve the mathematical model of steam flow and heat transfer in power plant condensers, the Streamline Upwind Petrov-Galerkin finite element method is applied. By comparison of the results of simulation with experimental results about an experimental condenser, it is confirmed that SUPG finite element method can be successfully applied for solving the three-dimensional mathematical model of steam flow and heat transfer in power plant condensers.
Abstract: The purpose of this study was to determine the most satisfying and frustrating aspects of ICT (Information and Communications Technologies) teaching in Turkish schools. Another aim was to compare these aspects based-on ICT teachers- selfefficacy. Participants were 119 ICT teachers from different geographical areas of Turkey. Participants were asked to list salient satisfying and frustrating aspects of ICT teaching, and to fill out the Self-Efficacy Scale for ICT Teachers. Results showed that the high self-efficacy teachers listed more positive and negative aspects of ICT teaching then did the low self-efficacy teachers. The satisfying aspects of ICT teaching were the dynamic nature of ICT subject, higher student interest, having opportunity to help other subject teachers, and lecturing in well-equipped labs, whereas the most frequently cited frustrating aspects of ICT teaching were ICT-related extra works of schools and colleagues, shortages of hardware and technical problems, indifferent students, insufficient teaching time, and the status of ICT subject in school curriculum. This information could be useful in redesigning ICT teachers- roles and responsibilities as well as job environment in schools.
Abstract: The aim of this study is to determine the basic information and communication technology (ICT) skills that may be needed by students studying in the 8th grade of the primary education in their cooperative project works implemented via the Internet. Within the scope of the study, the curriculum used for European Computer Driving License (ECDL) and the curriculum used in Turkey are also compared in terms of the ability to use ICT, which is aimed to be provided to the students. The research population of the study, during which the pre test – post test control group experimental model was used, consisted of 40 students from three different schools. In the first stage of the study, the skills that might be needed by students for their cooperative project works implemented via the Internet were determined through examination of the completed Comenious, e – twinning and WorldLinks projects. In the second stage of the study, the curriculums of the Turkish Ministry of National Education (MEB) and ECDL were evaluated by seven different teachers in line with these skills. Also in this study the ECDL and MEB curriculums were compared in terms of capability to provide the skills to implement cooperative projects via the Internet. In line with the findings of the study, the skills that might be needed by students to implement cooperative projects via the Internet were outlined, and existence of a significant difference was established in favor of the ECDL curriculum upon comparison of both curriculums in accordance with this outline (U = 50,500; p