Abstract: In this paper, we study statistical multiplexing of VBR
video in ATM networks. ATM promises to provide high speed realtime
multi-point to central video transmission for telemedicine
applications in rural hospitals and in emergency medical services.
Video coders are known to produce variable bit rate (VBR) signals
and the effects of aggregating these VBR signals need to be
determined in order to design a telemedicine network infrastructure
capable of carrying these signals. We first model the VBR video
signal and simulate it using a generic continuous-data autoregressive
(AR) scheme. We carry out the queueing analysis by the Fluid
Approximation Model (FAM) and the Markov Modulated Poisson
Process (MMPP). The study has shown a trade off: multiplexing
VBR signals reduces burstiness and improves resource utilization,
however, the buffer size needs to be increased with an associated
economic cost. We also show that the MMPP model and the Fluid
Approximation model fit best, respectively, the cell region and the
burst region. Therefore, a hybrid MMPP and FAM completely
characterizes the overall performance of the ATM statistical
multiplexer. The ramifications of this technology are clear: speed,
reliability (lower loss rate and jitter), and increased capacity in video
transmission for telemedicine. With migration to full IP-based
networks still a long way to achieving both high speed and high
quality of service, the proposed ATM architecture will remain of
significant use for telemedicine.
Abstract: Power line channel is proposed as an alternative for broadband data transmission especially in developing countries like Tanzania [1]. However the channel is affected by stochastic attenuation and deep notches which can lead to the limitation of channel capacity and achievable data rate. Various studies have characterized the channel without giving exactly the maximum performance and limitation in data transfer rate may be this is due to complexity of channel modeling being used. In this paper the channel performance of medium voltage, low voltage and indoor power line channel is presented. In the investigations orthogonal frequency division multiplexing (OFDM) with phase shift keying (PSK) as carrier modulation schemes is considered, for indoor, medium and low voltage channels with typical ten branches and also Golay coding is applied for medium voltage channel. From channels, frequency response deep notches are observed in various frequencies which can lead to reduce the achievable data rate. However, is observed that data rate up to 240Mbps is realized for a signal to noise ratio of about 50dB for indoor and low voltage channels, however for medium voltage a typical link with ten branches is affected by strong multipath and coding is required for feasible broadband data transfer.
Abstract: Particle swarm optimization (PSO) technique is applied to design the water distribution pipeline network. A simulation-optimization model is formulated with the objective of minimizing cost and is applied to a benchmark water distribution system optimization problem. The benchmark problem taken for the application of PSO technique to optimize the pipe size of the water distribution network is New York City water supply system problem. The results from the analysis infer that PSO is a potential alternative optimization technique when compared to other heuristic techniques for optimal sizing of water distribution systems.
Abstract: The African Great Lakes Region refers to the zone
around lakes Victoria, Tanganyika, Albert, Edward, Kivu, and
Malawi. The main source of electricity in this region is hydropower
whose systems are generally characterized by relatively weak,
isolated power schemes, poor maintenance and technical deficiencies
with limited electricity infrastructures. Most of the hydro sources are
rain fed, and as such there is normally a deficiency of water during
the dry seasons and extended droughts. In such calamities fossil fuels
sources, in particular petroleum products and natural gas, are
normally used to rescue the situation but apart from them being nonrenewable,
they also release huge amount of green house gases to our
environment which in turn accelerates the global warming that has at
present reached an amazing stage. Wind power is ample, renewable,
widely distributed, clean, and free energy source that does not
consume or pollute water. Wind generated electricity is one of the
most practical and commercially viable option for grid quality and
utility scale electricity production. However, the main shortcoming
associated with electric wind power generation is fluctuation in its
output both in space and time. Before making a decision to establish
a wind park at a site, the wind speed features there should therefore
be known thoroughly as well as local demand or transmission
capacity. The main objective of this paper is to utilise monthly
average wind speed data collected from one prospective site within
the African Great Lakes Region to demonstrate that the available
wind power there is high enough to generate electricity. The mean
monthly values were calculated from records gathered on hourly
basis for a period of 5 years (2001 to 2005) from a site in Tanzania.
The documentations that were collected at a height of 2 m were
projected to a height of 50 m which is the standard hub height of
wind turbines. The overall monthly average wind speed was found to
be 12.11 m/s whereas June to November was established to be the
windy season as the wind speed during the session is above the
overall monthly wind speed. The available wind power density
corresponding to the overall mean monthly wind speed was evaluated
to be 1072 W/m2, a potential that is worthwhile harvesting for the
purpose of electric generation.
Abstract: When dealing with safety in structures, the connections between structural components play an important role. Robustness of a structure as a whole depends both on the load- bearing capacity of the structural component and on the structures capacity to resist total failure, even though a local failure occurs in a component or a connection between components. To avoid progressive collapse it is necessary to be able to carry out a design for connections. A connection may be executed with anchors to withstand local failure of the connection in structures built with prefabricated components. For the design of these anchors, a model is developed for connections in structures performed in prefabricated autoclaved aerated concrete components. The design model takes into account the effect of anchors placed close to the edge, which may result in splitting failure. Further the model is developed to consider the effect of reinforcement diameter and anchor depth. The model is analytical and theoretically derived assuming a static equilibrium stress distribution along the anchor. The theory is compared to laboratory test, including the relevant parameters and the model is refined and theoretically argued analyzing the observed test results. The method presented can be used to improve safety in structures or even optimize the design of the connections
Abstract: The management of the health-care wastes is one of
the most important problems in Istanbul, a city with more than 12
million inhabitants, as it is in most of the developing countries.
Negligence in appropriate treatment and final disposal of the healthcare
wastes can lead to adverse impacts to public health and to the
environment. This paper employs a fuzzy multi-criteria group
decision making approach, which is based on the principles of fusion
of fuzzy information, 2-tuple linguistic representation model, and
technique for order preference by similarity to ideal solution
(TOPSIS), to evaluate health-care waste (HCW) treatment
alternatives for Istanbul. The evaluation criteria are determined
employing nominal group technique (NGT), which is a method of
systematically developing a consensus of group opinion. The
employed method is apt to manage information assessed using multigranularity
linguistic information in a decision making problem with
multiple information sources. The decision making framework
employs ordered weighted averaging (OWA) operator that
encompasses several operators as the aggregation operator since it
can implement different aggregation rules by changing the order
weights. The aggregation process is based on the unification of
information by means of fuzzy sets on a basic linguistic term set
(BLTS). Then, the unified information is transformed into linguistic
2-tuples in a way to rectify the problem of loss information of other
fuzzy linguistic approaches.
Abstract: There is a renewed interest in land use transport integration as a means of achieving sustainable accessibility. Such accessibility requires designing more than simply the transport network; it also requires attention to place (built form). Transitoriented development would appear to capture many of the criteria deemed important in land use transport integration. In Perth, Australia, there have been planning policies for the past 20 years requiring transit-oriented development around railway stations throughout the metropolitan area. While the policy intent, particularly at the State level, is clear the implementation of policy has been fairly ineffective. The first part of this paper provides an examination of state and local government planning and transport policies, evaluating them using a set of land use transport integration criteria considered all encompassing. This provides some insight into the extent of state and local government capacity to deliver land use transport integration. The second part of this paper examines the extent of implementation by examining existing and proposed land use around station precincts throughout metropolitan Perth. The findings of this research suggest that the capacity of state and local government to deliver land use transport integration is reasonable in a planning policy sense. Implementation, despite long policy lead times, has been lacking. It appears to be more effective where local planning controls have been suspended with new redevelopment authorities given powers to develop land around railway stations.
Abstract: In today-s competitive market, most companies
develop manufacturing systems that can help in cost reduction and
maximum quality. Human issues are an important part of
manufacturing systems, yet most companies ignore their effects on
production performance. This paper aims to developing an integrated
workforce planning system that incorporates the human being.
Therefore, a multi-objective mixed integer nonlinear programming
model is developed to determine the amount of hiring, firing,
training, overtime for each worker type. This paper considers a
workforce planning model including human aspects such as skills,
training, workers- personalities, capacity, motivation, and learning
rates. This model helps to minimize the hiring, firing, training and
overtime costs, and maximize the workers- performance. The results
indicate that the workers- differences should be considered in
workforce scheduling to generate realistic plans with minimum costs.
This paper also investigates the effects of human learning rates on the
performance of the production systems.
Abstract: The periodic mixed convection of a water-copper
nanofluid inside a rectangular cavity with aspect ratio of 3 is
investigated numerically. The temperature of the bottom wall of the
cavity is assumed greater than the temperature of the top lid which
oscillates horizontally with the velocity defined as u = u0 sin (ω t).
The effects of Richardson number, Ri, and volume fraction of
nanoparticles on the flow and thermal behavior of the nanofluid are
investigated. Velocity and temperature profiles, streamlines and
isotherms are presented. It is observed that when Ri < 1, heat transfer
rate is much greater than when Ri > 1. The higher value of Ri
corresponds to a lower value of the amplitude of the oscillation of
Num in the steady periodic state. Moreover, increasing the volume
fraction of the nanoparticles increases the heat transfer rate.
Abstract: To coop with urbanization issues and the economic need for expansion, the city of Jakarta is planning to reclaim more land in the Jakarta Bay. However, the reclamation activities of some islands have barely started and already the developers are facing difficulties in finding sufficient quantities of sand as fill material. When addressing the problem of sand scarcity in the case of Jakarta where, an excess of waste production, an inadequate solid waste management system and a lack of dumping ground pose a major problem, it is hard not to think of the use of waste as alternative fill material. This paper analyses the possibilities of using waste in the land reclamation projects, considering the governmental, social, environmental and economic context of the city. The results identify types of waste that could be used, ways of using those types of waste and implementation conditions for the city of Jakarta.
Abstract: Despite the fact that Knowledge Sharing (KS) is very important, we found only little discussion about the reasons why people have the willingness to share knowledge at such platform even though there is no immediate benefit to the persons who contribute knowledge in it. The aim of this study is to develop an integrative understanding of the factors that support or inhibit individuals- knowledge sharing intentions in virtual communities and to find whether habit would generate people-s willingness to be involved. We apply Social Capital Theory (SCT), and we also add two dimensions for discussion: member incentive and habitual domain (HD). This research assembles the questionnaire from individuals who have experienced knowledge sharing in virtual communities, and applies survey and Structural Equation Model (SEM) to analyze the results from the questionnaires. Finally, results confirm that individuals are willing to share knowledge in virtual communities: (1) if they consider reciprocity, centrality, and have longer tenure in their field, and enjoy helping. (2) if they have the habit of sharing knowledge. This study is useful for the developers of virtual communities to insight into knowledge sharing in cyberspace.
Abstract: Cities expansion, urban travels increase, the
technology development, the automobile price cheapen, and the
families' income ascending cause the considerable increase in
automobile numbers of the city. This fact has led to the traffic
creation and the automobile parking site shortage in the city. Also in
Esfahan metropolis, the parking lots shortage has been the great
problem of this town; in addition, in designing and constructing of
the parking sites the traditional methods are utilized which do not
have a reasonable and optimized usage of the valuable urban lands. In
this article, by introducing the prefabricate mechanized parking
system which is inexpensive, simple and quick, and occupies very
small space, therefore provides the high content of parking site for
the cities, we can eliminate the parking space shortage difficulty of
the cities. The achieved results of this research represent that an
optimized utilization of the existent urban spaces for parking site
construction has not been accomplished. By employing the new
parking site technologies such as mechanization categorized parking
sites and the capacity prefabricate mechanized of each parking space
have become 8 multiples; in this case, the valuable urban lands can
be used in an optimized way.
Abstract: The overall service performance of I/O intensive
system depends mainly on workload on its storage system. In
heterogeneous storage environment where storage elements from
different vendors with different capacity and performance are put
together, workload should be distributed according to storage
capability. This paper addresses data placement issue in short video
sharing website. Workload contributed by a video is estimated by the
number of views and life time span of existing videos in same
category. Experiment was conducted on 42,000 video titles in six
weeks. Result showed that the proposed algorithm distributed
workload and maintained balance better than round robin and random
algorithms.
Abstract: In the upgrade process of enterprise information
systems, how to deal with and utilize those legacy systems affects the
efficiency of construction and development of the new system. We
propose an evaluation system, which comprehensively describes the
capacity of legacy information systems in five aspects. Then we
propose a practical legacy systems evaluation method. Base on the
evaluation result, we can determine the current state of legacy system
which was evaluated.
Abstract: Magnesium wastes are produced by many industrial activities. This waste problem is becoming a future problem for the world. Magnesium borates have many advantages such as; high corrosion resistance, heat resistance, high coefficient of elasticity and can also be used in the production of material against radiation. Addition, magnesium borates have great potential in sectors
including ceramic and detergents industry and superconducting materials.
In this study, using the starting materials of waste magnesium and H3BO3 the hydrothermal method was applied at a moderate
temperature of 70oC. Several mole ratios of waste magnesium to H3BO3 are selected as; 1:2, 1:4, 1:6, 1:8, 1:10. Reaction time was determined as 1 hour. After the synthesis, X-Ray Diffraction (XRD) and Fourier Transform Infrared Spectroscopy (FT-IR) techniques are applied to products. As a result the forms of mcallisterite “Mg2(B6O7(OH)6)2.9(H2O)”, admontite “MgO(B2O3)3.7(H2O)” and magnesium boron hydrate (MgO(B2O3)3.6(H2O)” are obtained.
Abstract: The characterization and modeling of the dynamic
behavior of many built-up structures under vibration conditions is still
a subject of current research. The present study emphasizes the
theoretical investigation of slip damping in layered and jointed
welded cantilever structures using finite element approach.
Application of finite element method in damping analysis is relatively
recent, as such, some problems particularly slip damping analysis has
not received enough attention. To validate the finite element model
developed, experiments have been conducted on a number of mild
steel specimens under different initial conditions of vibration. Finite
element model developed affirms that the damping capacity of such
structures is influenced by a number of vital parameters such as;
pressure distribution, kinematic coefficient of friction and micro-slip
at the interfaces, amplitude, frequency of vibration, length and
thickness of the specimen. Finite element model developed can be
utilized effectively in the design of machine tools, automobiles,
aerodynamic and space structures, frames and machine members for
enhancing their damping capacity.
Abstract: The direct synthesis process of dimethyl ether (DME)
from syngas in slurry reactors is considered to be promising because
of its advantages in caloric transfer. In this paper, the influences of
operating conditions (temperature, pressure and weight hourly space
velocity) on the conversion of CO, selectivity of DME and methanol
were studied in a stirred autoclave over Cu-Zn-Al-Zr slurry catalyst,
which is far more suitable to liquid phase dimethyl ether synthesis
process than bifunctional catalyst commercially. A Langmuir-
Hinshelwood mechanism type global kinetics model for liquid phase
DME direct synthesis based on methanol synthesis models and a
methanol dehydration model has been investigated by fitting our
experimental data. The model parameters were estimated with
MATLAB program based on general Genetic Algorithms and
Levenberg-Marquardt method, which is suitably fitting experimental
data and its reliability was verified by statistical test and residual
error analysis.
Abstract: In this work, new experimental data for slugging
frequency in inclined gas-liquid flow are reported, and a new
correlation is proposed. Scale experiments were carried out using a
mixture of air and water in a 6 m long pipe. Two different pipe
diameters were used, namely, 38 and 67 mm. The data were taken
with capacitance type sensors at a data acquisition frequency of 200
Hz over an interval of 60 seconds. For the range of flow conditions
studied, the liquid superficial velocity is observed to influence the
frequency strongly. A comparison of the present data with
correlations available in the literature reveals a lack of agreement. A
new correlation for slug frequency has been proposed for the inclined
flow, which represents the main contribution of this work.
Abstract: HIV-1 genome is highly heterogeneous. Due to this
variation, features of HIV-I genome is in a wide range. For this
reason, the ability to infection of the virus changes depending on
different chemokine receptors. From this point of view, R5 HIV
viruses use CCR5 coreceptor while X4 viruses use CXCR5 and
R5X4 viruses can utilize both coreceptors. Recently, in
Bioinformatics, R5X4 viruses have been studied to classify by using
the experiments on HIV-1 genome.
In this study, R5X4 type of HIV viruses were classified using
Auto Regressive (AR) model through Artificial Neural Networks
(ANNs). The statistical data of R5X4, R5 and X4 viruses was
analyzed by using signal processing methods and ANNs. Accessible
residues of these virus sequences were obtained and modeled by AR
model since the dimension of residues is large and different from
each other. Finally the pre-processed data was used to evolve various
ANN structures for determining R5X4 viruses. Furthermore ROC
analysis was applied to ANNs to show their real performances. The
results indicate that R5X4 viruses successfully classified with high
sensitivity and specificity values training and testing ROC analysis
for RBF, which gives the best performance among ANN structures.
Abstract: German electricity European options on futures using
Lévy processes for the underlying asset are examined. Implied
volatility evolution, under each of the considered models, is
discussed after calibrating for the Merton jump diffusion (MJD),
variance gamma (VG), normal inverse Gaussian (NIG), Carr, Geman,
Madan and Yor (CGMY) and the Black and Scholes (B&S) model.
Implied volatility is examined for the entire sample period, revealing
some curious features about market evolution, where data fitting
performances of the five models are compared. It is shown that
variance gamma processes provide relatively better results and that
implied volatility shows significant differences through time, having
increasingly evolved. Volatility changes for changed uncertainty, or
else, increasing futures prices and there is evidence for the need to
account for seasonality when modelling both electricity spot/futures
prices and volatility.