Abstract: A mathematical model based on a mass and energy
balance for the combustion in a cement rotary kiln was developed.
The model was used to investigate the impact of replacing about
45 % of the primary coal energy by different alternative fuels.
Refuse derived fuel, waste wood, solid hazardous waste and liquid
hazardous waste were used in the modeling. The results showed that
in order to keep the kiln temperature unchanged, and thereby
maintain the required clinker quality, the production capacity had to
be reduced by 1-15 %, depending on the fuel type. The reason for the
reduction is increased exhaust gas flow rates caused by the fuel
characteristics. The model, which has been successfully validated in a
full-scale experiment, was also used to show that the negative impact
on the production capacity can be avoided if a relatively small part of
the combustion air is replaced by pure oxygen.
Abstract: Scolothrips longicornis Priesner is one of the
important predators of tetranychid mites with a wide distribution
throughout Iran. Life table and population growth parameters of S.
longicornis feeding on two-spotted spider mite, Tetranychus
turkestani Ugarov & Nikolski were investigated under laboratory
condition (26±1ºC, 65±5% R.H. and 16L: 8D). To carry of these
experiments, S. longicornis collections reared on cowpea infested
with T. turkestani were prepared. The eggs with less than 24 hours
old were selected and reared. The emerged larvae feeding directly on
cowpea leaf discs which were infested with T. turkestani. Thirty
females of S. longicornis with 24 hours age were selected and
released on infested leaf discs. They replaced daily to a new leaf disc
and the laying eggs have counted. The experiment continued till the
last thrips had died. The result showed that the mean age mortality of
the adult female thrips were between 21-25 days which is nearly
equal life expectancy (ex) at the time of adult eclosion. Parameters
related to reproductive table including gross reproductive rate, net
reproductive rate, intrinsic rate of natural increase and finite rate of
increase were 48.91, 37.63, 0.26 and 2.3, respectively. Mean age per
female/day, mean fertile egg per female/day, gross hatch rate, mean
net age fertility, mean net age fecundity, net fertility rate and net
fecundity rate were 2.23, 1.76, 0.87, 13.87, 14.26, 69.1 and 78.5,
respectively. Sex ratio of offspring also recorded daily. The highest
sex ratio for females was 0.88 in first day of oviposition. The sex
ratio decreased gradually and reached under 0.46 after the day 26 and
the oviposition rate declined. Then it seems that maintenance of
rearing culture of predatory thrips for mass rearing later than 26 days
after egg-laying commence is not profitable.
Abstract: Severe symptoms, such as dissociation, depersonalization, self-mutilation, suicidal ideations and gestures, are the main reasons for a person to be diagnosed with Borderline Personality Disorder (BPD) and admitted to an inpatient Psychiatric Hospital. However, these symptoms are also indicators of a severe traumatic history as indicated by the extensive research on the topic. Unfortunately patients with such clinical presentation often are treated repeatedly only for their symptomatic behavior, while the main cause for their suffering, the trauma itself, is usually left unaddressed therapeutically. All of the highly structured, replicable, and manualized treatments lack the recognition of the uniqueness of the person and fail to respect his/her rights to experience and react in an idiosyncratic manner. Thus the communicative and adaptive meaning of such symptomatic behavior is missed. Only its pathological side is recognized and subjected to correction and stigmatization, and the message that the person is damaged goods that needs fixing is conveyed once again. However, this time the message would be even more convincing for the victim, because it is sent by mental health providers, who have the credibility to make such a judgment. The result is a revolving door of very expensive hospitalizations for only a temporary and patchy fix. In this way the patients, once victims of abuse and hardship are left invalidated and thus their re-victimization is perpetuated in their search for understanding and help. Keywordsborderline personality disorder (BPD), complex PTSD, integrative treatment of trauma, re-victimization of trauma victims.
Abstract: Multimedia security is an incredibly significant area of concern. The paper aims to discuss a robust image watermarking scheme, which can withstand geometric attacks. The source image is initially moment normalized in order to make it withstand geometric attacks. The moment normalized image is wavelet transformed. The first level wavelet transformed image is segmented into blocks if size 8x8. The product of mean and standard and standard deviation of each block is computed. The second level wavelet transformed image is divided into 8x8 blocks. The product of block mean and the standard deviation are computed. The difference between products in the two levels forms the watermark. The watermark is inserted by modulating the coefficients of the mid frequencies. The modulated image is inverse wavelet transformed and inverse moment normalized to generate the watermarked image. The watermarked image is now ready for transmission. The proposed scheme can be used to validate identification cards and financial instruments. The performance of this scheme has been evaluated using a set of parameters. Experimental results show the effectiveness of this scheme.
Abstract: Charging and discharging phenomenon on the surface
of materials can be found in plasma display panel, spacecraft
charging, high voltage insulator, etc. This report gives a simple
explanation on this phenomenon. A scanning electron microscope
was used not only as a tool to produce energetic electron beam to
charge an insulator without metallic coating and to produce a surface
discharging (surface breakdown/flashover) but also to observe the
visible charging and discharging on the sample surface. A model of
electric field distribution on the surface was developed in order to
explain charging and discharging phenomena. Since charging and
discharging process involves incubation time, therefore this process
can be used to evaluate the insulation property of materials under
electron bombardment.
Abstract: Music segmentation is a key issue in music information
retrieval (MIR) as it provides an insight into the
internal structure of a composition. Structural information about
a composition can improve several tasks related to MIR such
as searching and browsing large music collections, visualizing
musical structure, lyric alignment, and music summarization.
The authors of this paper present the MTSSM framework, a twolayer
framework for the multi-track segmentation of symbolic
music. The strength of this framework lies in the combination of
existing methods for local track segmentation and the application
of global structure information spanning via multiple tracks.
The first layer of the MTSSM uses various string matching
techniques to detect the best candidate segmentations for each
track of a multi-track composition independently. The second
layer combines all single track results and determines the best
segmentation for each track in respect to the global structure of
the composition.
Abstract: Bubble columns have a variety of applications in
absorption, bio-reactions, catalytic slurry reactions, and coal
liquefaction; because they are simple to operate, provide good heat
and mass transfer, having less operational cost. The use of
Computational Fluid Dynamics (CFD) for bubble column becomes
important, since it can describe the fluid hydrodynamics on both local
and global scale. Euler- Euler two-phase fluid model has been used to
simulate two-phase (air and water) transient up-flow in bubble
column (15cm diameter) using FLUENT6.3. These simulations and
experiments were operated over a range of superficial gas velocities
in the bubbly flow and churn turbulent regime (1 to16 cm/s) at
ambient conditions. Liquid velocity was varied from 0 to 16cm/s. The
turbulence in the liquid phase is described using the standard k-ε
model. The interactions between the two phases are described
through drag coefficient formulations (Schiller Neumann). The
objectives are to validate CFD simulations with experimental data,
and to obtain grid-independent numerical solutions. Quantitatively
good agreements are obtained between experimental data for hold-up
and simulation values. Axial liquid velocity profiles and gas holdup
profiles were also obtained for the simulation.
Abstract: Although lighting systems powered by Photovoltaic
(PV) cells have existed for many years, they are not widely used,
especially in lighting for buildings, due to their high initial cost and
low conversion efficiency. One of the technical challenges facing PV
powered lighting systems has been how to use dc power generated by
the PV module to energize common light sources that are designed to
operate efficiently under ac power. Usually, the efficiency of the dc
light sources is very poor compared to ac light sources. Rapid
developments in LED lighting systems have made this technology a
potential candidate for PV powered lighting systems. This study
analyzed the efficiency of each component of PV powered lighting
systems to identify optimum system configurations for different
applications.
Abstract: Thermal conductivity is an important characteristic of
a nanofluid in laminar flow heat transfer. This paper presents an
improved model for the prediction of the effective thermal
conductivity of nanofluids based on dimensionless groups. The
model expresses the thermal conductivity of a nanofluid as a function
of the thermal conductivity of the solid and liquid, their volume
fractions and particle size. The proposed model includes a parameter
which accounts for the interfacial shell, brownian motion, and
aggregation of particle. The validation of the model is verified by
applying the results obtained by the experiments of Tio2-water and
Al2o3-water nanofluids.
Abstract: The springs located in urban areas are the outpouring
of surface water, which can serve as water supply, effluent receptors
and important local macro-drainage elements. With unplanned
occupation, non-compliance with environmental legislation and the
importance of these water bodies, it is vital to analyze the springs
within urban areas, considering the Brazilian forest code. This paper
submits an analysis and discussion methodology proposal of
environmental compliance functions of urban springs, by means of
G.I.S. - Geographic Information System analysis - and in situ
analysis. The case study included two springs which exhibit a history
of occupation along its length, with different degrees of impact. The
proposed method is effective and easy to apply, representing a
powerful tool for analyzing the environmental conditions of springs
in urban areas.
Abstract: This paper describes a newly designed decentralized
nonlinear control strategy to control a robot manipulator. Based on the
concept of the nonlinear state feedback theory and decentralized
concept is developed to improve the drawbacks in previous works
concerned with complicate intelligent control and low cost effective
sensor. The control methodology is derived in the sense of Lyapunov
theorem so that the stability of the control system is guaranteed. The
decentralized algorithm does not require other joint angle and velocity
information. Individual Joint controller is implemented using a digital
processor with nearly actuator to make it possible to achieve good
dynamics and modular. Computer simulation result has been
conducted to validate the effectiveness of the proposed control scheme
under the occurrence of possible uncertainties and different reference
trajectories. The merit of the proposed control system is indicated in
comparison with a classical control system.
Abstract: There are several approaches in trying to solve the
Quantitative 1Structure-Activity Relationship (QSAR) problem.
These approaches are based either on statistical methods or on
predictive data mining. Among the statistical methods, one should
consider regression analysis, pattern recognition (such as cluster
analysis, factor analysis and principal components analysis) or partial
least squares. Predictive data mining techniques use either neural
networks, or genetic programming, or neuro-fuzzy knowledge. These
approaches have a low explanatory capability or non at all. This
paper attempts to establish a new approach in solving QSAR
problems using descriptive data mining. This way, the relationship
between the chemical properties and the activity of a substance
would be comprehensibly modeled.
Abstract: Mining frequent tree patterns have many useful
applications in XML mining, bioinformatics, network routing, etc.
Most of the frequent subtree mining algorithms (i.e. FREQT,
TreeMiner and CMTreeMiner) use anti-monotone property in the
phase of candidate subtree generation. However, none of these
algorithms have verified the correctness of this property in tree
structured data. In this research it is shown that anti-monotonicity
does not generally hold, when using weighed support in tree pattern
discovery. As a result, tree mining algorithms that are based on this
property would probably miss some of the valid frequent subtree
patterns in a collection of trees. In this paper, we investigate the
correctness of anti-monotone property for the problem of weighted
frequent subtree mining. In addition we propose W3-Miner, a new
algorithm for full extraction of frequent subtrees. The experimental
results confirm that W3-Miner finds some frequent subtrees that the
previously proposed algorithms are not able to discover.
Abstract: In this paper, the melting of a semi-infinite body as a
result of a moving laser beam has been studied. Because the Fourier
heat transfer equation at short times and large dimensions does not
have sufficient accuracy; a non-Fourier form of heat transfer
equation has been used. Due to the fact that the beam is moving in x
direction, the temperature distribution and the melting pool shape are
not asymmetric. As a result, the problem is a transient threedimensional
problem. Therefore, thermophysical properties such as
heat conductivity coefficient, density and heat capacity are functions
of temperature and material states. The enthalpy technique, used for
the solution of phase change problems, has been used in an explicit
finite volume form for the hyperbolic heat transfer equation. This
technique has been used to calculate the transient temperature
distribution in the semi-infinite body and the growth rate of the melt
pool. In order to validate the numerical results, comparisons were
made with experimental data. Finally, the results of this paper were
compared with similar problem that has used the Fourier theory. The
comparison shows the influence of infinite speed of heat propagation
in Fourier theory on the temperature distribution and the melt pool
size.
Abstract: In this study, the hydrogen transport phenomenon was
numerically evaluated by using hydrogen-enhanced localized
plasticity (HELP) mechanisms. Two dominant governing equations,
namely, the hydrogen transport model and the elasto-plastic model,
were introduced. In addition, the implicitly formulated equations of
the governing equations were implemented into ABAQUS UMAT
user-defined subroutines. The simulation results were compared to
published results to validate the proposed method.
Abstract: This paper presents a new and efficient approach for
capacitor placement in radial distribution systems that determine
the optimal locations and size of capacitor with an objective of
improving the voltage profile and reduction of power loss. The
solution methodology has two parts: in part one the loss sensitivity
factors are used to select the candidate locations for the capacitor
placement and in part two a new algorithm that employs Plant growth
Simulation Algorithm (PGSA) is used to estimate the optimal size
of capacitors at the optimal buses determined in part one. The main
advantage of the proposed method is that it does not require any
external control parameters. The other advantage is that it handles the
objective function and the constraints separately, avoiding the trouble
to determine the barrier factors. The proposed method is applied to 9
and 34 bus radial distribution systems. The solutions obtained by the
proposed method are compared with other methods. The proposed
method has outperformed the other methods in terms of the quality
of solution.
Abstract: Diagnostic and detection of the arterial stiffness is
very important; which gives indication of the associated increased risk of cardiovascular diseases. To make a cheap and easy method for general screening technique to avoid the future cardiovascular
complexes , due to the rising of the arterial stiffness ; a proposed algorithm depending on photoplethysmogram to be used. The
photoplethysmograph signals would be processed in MATLAB. The
signal will be filtered, baseline wandering removed, peaks and
valleys detected and normalization of the signals should be achieved
.The area under the catacrotic phase of the photoplethysmogram
pulse curve is calculated using trapezoidal algorithm ; then will used
in cooperation with other parameters such as age, height, blood
pressure in neural network for arterial stiffness detection. The Neural
network were implemented with sensitivity of 80%, accuracy 85%
and specificity of 90% were got from the patients data. It is
concluded that neural network can detect the arterial STIFFNESS
depending on risk factor parameters.
Abstract: Land with low pH soil spread widely in Indonesia
can be used for soybean (Glycine max) cultivation, however the
production is low. The use of acid tolerant soybean and acidaluminium
tolerant nitrogen-fixing bacteria formula was an
alternative way to increase soybean productivity on acid soils.
Bradyrhizobium japonicum is one of the nitrogen fixing bacteria
which can symbiose with soybean plants through root nodule
formation. Most of the nitrogen source required by soybean plants
can be provided by this symbiosis. This research was conducted to
study the influence of acid-aluminium tolerant B. japonicum strain
BJ 11 formula using peat as carrier on growth of Tanggamus and
Anjasmoro cultivar soybean planted on acid soil fields (pH 5.0-
5.5). The results showed that the inoculant was able to increase the
growth and production of soybean which were grown on fields acid
soil at Sukadana (Lampung) and Tanah Laut (South Kalimantan),
Indonesia.
Abstract: This paper discusses a systematic design of a Σ-Δ fractional-N Phase-Locked Loop based on HDL behavioral modeling. The proposed design consists in describing the mixed behavior of this PLL architecture starting from the specifications of each building block. The HDL models of critical PLL blocks have been described in VHDL-AMS to predict the different specifications of the PLL. The effect of different noise sources has been efficiently introduced to study the PLL system performances. The obtained results are compared with transistor-level simulations to validate the effectiveness of the proposed models for wireless applications in the frequency range around 2.45 GHz.
Abstract: Displacement measurement was conducted on compact normal and shear specimens made of acrylic homogeneous material subjected to mixed-mode loading by digital image correlation. The intelligent hybrid method proposed by Nishioka et al. was applied to the stress-strain analysis near the crack tip. The accuracy of stress-intensity factor at the free surface was discussed from the viewpoint of both the experiment and 3-D finite element analysis. The surface images before and after deformation were taken by a CMOS camera, and we developed the system which enabled the real time stress analysis based on digital image correlation and inverse problem analysis. The great portion of processing time of this system was spent on displacement analysis. Then, we tried improvement in speed of this portion. In the case of cracked body, it is also possible to evaluate fracture mechanics parameters such as the J integral, the strain energy release rate, and the stress-intensity factor of mixed-mode. The 9-points elliptic paraboloid approximation could not analyze the displacement of submicron order with high accuracy. The analysis accuracy of displacement was improved considerably by introducing the Newton-Raphson method in consideration of deformation of a subset. The stress-intensity factor was evaluated with high accuracy of less than 1% of the error.