Abstract: It is necessary to evaluate the bridges conditions and
strengthen bridges or parts of them. The reinforcement necessary due
to some reasons can be summarized as: First, a changing in use of
bridge could produce internal forces in a part of structural which
exceed the existing cross-sectional capacity. Second, bridges may
also need reinforcement because damage due to external factors
which reduced the cross-sectional resistance to external loads. One of
other factors could listed here its misdesign in some details, like
safety of bridge or part of its.This article identify the design demands
of Qing Shan bridge located in is in Heilongjiang Province He gang -
Nen Jiang Road 303 provincial highway, Wudalianchi area, China, is
an important bridge in the urban areas. The investigation program
was include the observation and evaluate the damage in T- section
concrete beams , prestressed concrete box girder bridges section in
additional evaluate the whole state of bridge includes the pier ,
abutments , bridge decks, wings , bearing and capping beam, joints,
........etc. The test results show that the bridges in general structural
condition are good. T beam span No 10 were observed, crack
extended upward along the ribbed T beam, and continue to the T
beam flange. Crack width varying between 0.1mm to 0.4mm, the
maximum about 0.4mm. The bridge needs to be improved flexural
bending strength especially at for T beam section.
Abstract: A fully on-chip low drop-out (LDO) voltage regulator with 100pF output load capacitor is presented. A novel frequency compensation scheme using current buffer is adopted to realize single dominant pole within the unit gain frequency of the regulation loop, the phase margin (PM) is at least 50 degree under the full range of the load current, and the power supply rejection (PSR) character is improved compared with conventional Miller compensation. Besides, the differentiator provides a high speed path during the load current transient. Implemented in 0.18μm CMOS technology, the LDO voltage regulator provides 100mA load current with a stable 1.8V output voltage consuming 80μA quiescent current.
Abstract: In order to improve control performance and eliminate steady, a coupling compensation for 6-DOF parallel robot is presented. Taking dynamic load Tank Simulator as the research object, this paper analyzes the coupling of 6-DOC parallel robot considering the degree of freedom of the 6-DOF parallel manipulator. The coupling angle and coupling velocity are derived based on inverse kinematics model. It uses the mechanism-model combined method which takes practical moving track that considering the performance of motion controller and motor as its input to make the study. Experimental results show that the coupling compensation improves motion stability as well as accuracy. Besides, it decreases the dither amplitude of dynamic load Tank Simulator.
Abstract: There is increasing evidence that earthquakes produce electromagnetic signals observable at the surface in the extremely low to very low freqency (ELF - VLF) range often in advance to the main event. These precursors are candidates for prediction purposes. Laboratory experiments con´¼ürm that material under load emits an electromagnetic signature, the detailed generation mechanisms how- ever are not well understood yet.
Abstract: The paper focuses on the enhanced stiffness modeling
of robotic manipulators by taking into account influence of the external force/torque acting upon the end point. It implements the
virtual joint technique that describes the compliance of manipulator elements by a set of localized six-dimensional springs separated by
rigid links and perfect joints. In contrast to the conventional
formulation, which is valid for the unloaded mode and small
displacements, the proposed approach implicitly assumes that the loading leads to the non-negligible changes of the manipulator posture and corresponding amendment of the Jacobian. The
developed numerical technique allows computing the static
equilibrium and relevant force/torque reaction of the manipulator for
any given displacement of the end-effector. This enables designer
detecting essentially nonlinear effects in elastic behavior of
manipulator, similar to the buckling of beam elements. It is also proposed the linearization procedure that is based on the inversion of
the dedicated matrix composed of the stiffness parameters of the
virtual springs and the Jacobians/Hessians of the active and passive
joints. The developed technique is illustrated by an application example that deals with the stiffness analysis of a parallel
manipulator of the Orthoglide family
Abstract: This paper presents performance comparison of three estimation techniques used for peak load forecasting in power systems. The three optimum estimation techniques are, genetic algorithms (GA), least error squares (LS) and, least absolute value filtering (LAVF). The problem is formulated as an estimation problem. Different forecasting models are considered. Actual recorded data is used to perform the study. The performance of the above three optimal estimation techniques is examined. Advantages of each algorithms are reported and discussed.
Abstract: Workload and resource management are two essential functions provided at the service level of the grid software infrastructure. To improve the global throughput of these software environments, workloads have to be evenly scheduled among the available resources. To realize this goal several load balancing strategies and algorithms have been proposed. Most strategies were developed in mind, assuming homogeneous set of sites linked with homogeneous and fast networks. However for computational grids we must address main new issues, namely: heterogeneity, scalability and adaptability. In this paper, we propose a layered algorithm which achieve dynamic load balancing in grid computing. Based on a tree model, our algorithm presents the following main features: (i) it is layered; (ii) it supports heterogeneity and scalability; and, (iii) it is totally independent from any physical architecture of a grid.
Abstract: MBMS is a unidirectional point-to-multipoint bearer
service in which data are transmitted from a single source entity to
multiple recipients. For a mobile to support the MBMS, MBMS client
functions as well as MBMS radio protocols should be designed and
implemented. In this paper, we analyze the MBMS client functions
and describe the implementation of them in our mobile test-bed. User
operations and signaling flows between protocol entities to control the
MBMS functions are designed in detail. Service announcement
utilizing the file download MBMS service and four MBMS user
services are demonstrated in the test-bed to verify the MBMS client
functions.
Abstract: Effectiveness and efficiency of food distribution is necessary to maintain food security in a region. Food supply varies among regions depending on their production capacity; therefore, it is necessary to regulate food distribution. Sea transportation could play a great role in the food distribution system. To play this role and to support transportation needs in the Eastern Indonesia, sea transportation shall be supported by fleet which is adequate and reliable, both in terms of load and worthiness. This research uses Linear Programming (LP) method to analyze food distribution pattern in order to determine the optimal distribution system. In this research, transshipment points have been selected for regions in one province. Comparison between result of modeling and existing shipping route reveals that from 369 existing routes, 54 routes are used for transporting rice, corn, green bean, peanut, soybean, sweet potato, and cassava.
Abstract: This paper deals with a novel technique for the
fabrication of Spiral grooves in a dynamic thrust bearing. The main
scheme proposed in this paper is to fabricate the microgrooves using
desktop forming system. This process has advantages compared to the
conventional electro-chemical machining in the viewpoint of a higher
productivity. For this reason, a new testing apparatus is designed and
built for press forming microgrooves on a surface of the thrust bearing.
The material used in this study is sintered Cu-Fe alloy. The effects of
the forming load on the performance of micro press forming are
experimentally investigated. From the experimental results, formed
depths are closed to the target ones with increasing the forming load.
Abstract: Cement stabilization has been widely used for
improving the strength and stiffness of soft clayey soils. Cement
treated soil specimens used to investigate the stress-strain behaviour in
the laboratory study are usually cured for 7 days. This paper examines
the effects of curing time on the strength and stress strain behaviour of
cement treated marine clay under triaxial loading condition.
Laboratory-prepared cement treated Singapore marine clay with
different mix proportion S-C-W (soil solid-cement solid-water) and
curing time (7 days to 180 days) was investigated through conducting
unconfined compressive strength test and triaxial test. The results
show that the curing time has a significant effect on the unconfined
compressive strength u q , isotropic compression behaviour and stress
strain behaviour. Although the primary yield loci of the cement treated
soil specimens with the same mix proportion expand with curing time,
they are very narrowly banded and have nearly the same shape after
being normalized by isotropic compression primary stress '
py p . The
isotropic compression primary yield stress '
py p was shown to be
linearly related to unconfined compressive strength u q for specimens
with different curing time and mix proportion. The effect of curing
time on the hardening behaviour will diminish with consolidation
stress higher than isotropic compression primary yield stress but its
damping rate is dependent on the cement content.
Abstract: Computer programming is considered a very difficult
course by many computer science students. The reasons for the
difficulties include cognitive load involved in programming,
different learning styles of students, instructional methodology and
the choice of the programming languages. To reduce the difficulties
the following have been tried: pair programming, program
visualization, different learning styles etc. However, these efforts
have produced limited success. This paper reviews the problem and
proposes a framework to help students overcome the difficulties
involved.
Abstract: Application of wood in rural construction is diffused
all around the world since remote times. However, its inclusion in
structural design deserves strong support from broad knowledge of
material properties. The pertinent literature reveals the application of
optical methods in determining the complete field displacement on
bodies exhibiting regular as well as irregular surfaces. The use of
moiré techniques in experimental mechanics consists in analyzing the
patterns generated on the body surface before and after deformation.
The objective of this research work is to study the qualitative
deformation behavior of wooden testing specimens under specific
loading situations. The experiment setup follows the literature
description of shadow moiré methods. Results indicate strong
anisotropy influence of the generated displacement field. Important
qualitative as well as quantitative stress and strain distribution were
obtained wooden members which are applicable to rural
constructions.
Abstract: In this work, we experimentally study heat transfer
from exhaust particulate air of detergent spray drying tower to water
by using coiled tube heat exchanger. Water flows in the coiled
tubes, where air loaded with detergent particles of 43 micrometers
in diameter flows within the shell. Four coiled tubes with different
coil pitches are used in a counter-current flow configuration. We
investigate heat transfer coefficients of inside and outside the heat
transfer surfaces through 400 experiments. The correlations between
Nusselt number and Reynolds number, Prandtl number, mass flow
rate of particulates to mass flow rate of air ratio and coiled tube
pitch parameter are proposed. The correlations procured can be used
to predicted heat transfer between tube and shell of the heat
exchanger.
Abstract: In the traditional theory of non-uniform torsion the
axial displacement field is expressed as the product of the unit twist
angle and the warping function. The first one, variable along the
beam axis, is obtained by a global congruence condition; the second
one, instead, defined over the cross-section, is determined by solving
a Neumann problem associated to the Laplace equation, as well as for
the uniform torsion problem.
So, as in the classical theory the warping function doesn-t punctually
satisfy the first indefinite equilibrium equation, the principal aim of
this work is to develop a new theory for non-uniform torsion of
beams with axial symmetric cross-section, fully restrained on both
ends and loaded by a constant torque, that permits to punctually
satisfy the previous equation, by means of a trigonometric expansion
of the axial displacement and unit twist angle functions.
Furthermore, as the classical theory is generally applied with good
results to the global and local analysis of ship structures, two beams
having the first one an open profile, the second one a closed section,
have been analyzed, in order to compare the two theories.
Abstract: Power-line networks are widely used today for broadband data transmission. However, due to multipaths within the broadband power line communication (BPLC) systems owing to stochastic changes in the network load impedances, branches, etc., network or channel capacity performances are affected. This paper attempts to investigate the performance of typical medium voltage channels that uses Orthogonal Frequency Division Multiplexing (OFDM) techniques with Quadrature Amplitude Modulation (QAM) sub carriers. It has been observed that when the load impedances are different from line characteristic impedance channel performance decreases. Also as the number of branches in the link between the transmitter and receiver increases a loss of 4dB/branch is found in the signal to noise ratio (SNR). The information presented in the paper could be useful for an appropriate design of the BPLC systems.
Abstract: This paper undertakes the problem of optimal
capacitor placement in a distribution system. The problem is how to
optimally determine the locations to install capacitors, the types and
sizes of capacitors to he installed and, during each load level,the
control settings of these capacitors in order that a desired objective
function is minimized while the load constraints,network constraints
and operational constraints (e.g. voltage profile) at different load
levels are satisfied. The problem is formulated as a combinatorial
optimization problem with a nondifferentiable objective function.
Four solution mythologies based on algorithms (GA),tabu search
(TS), and hybrid GA-SA algorithms are presented.The solution
methodologies are preceded by a sensitivity analysis to select the
candidate capacitor installation locations.
Abstract: Linear stability of wake-shear layers in two-phase
shallow flows is analyzed in the present paper. Stability analysis is
based on two-dimensional shallow water equations. It is assumed that
the fluid contains uniformly distributed solid particles. No dynamic
interaction between the carrier fluid and particles is expected in the
initial moment. Linear stability curves are obtained for different
values of the particle loading parameter, the velocity ratio and the
velocity deficit. It is shown that the increase in the velocity ratio
destabilizes the flow. The particle loading parameter has a stabilizing
effect on the flow. The role of the velocity deficit is also
destabilizing: the increase of the velocity deficit leads to less stable
flow.
Abstract: Voltage flicker is a disturbance in electrical power
systems. The reason for this disturbance is mainly the large nonlinear
loads such as electric arc furnaces. Synchronous static
compensator (STATCOM) is considered as a proper technique to
mitigate the voltage flicker. Application of more suitable and precise
power electronic converter leads to a more precise performance of the
compensator. In this paper a three-level 12-pulse voltage source
inverter (VSI) with a 12-terminal transformer connected to the ac
system is studied and the obtained results are compared with the
performance of a STATCOM using a simple two-level VSI and an
optimal and more precise performance of the proposed scheme is
achieved.
Abstract: In general, class complexity is measured based on any
one of these factors such as Line of Codes (LOC), Functional points
(FP), Number of Methods (NOM), Number of Attributes (NOA) and so on. There are several new techniques, methods and metrics with
the different factors that are to be developed by the researchers for calculating the complexity of the class in Object Oriented (OO)
software. Earlier, Arockiam et.al has proposed a new complexity measure namely Extended Weighted Class Complexity (EWCC)
which is an extension of Weighted Class Complexity which is proposed by Mishra et.al. EWCC is the sum of cognitive weights of
attributes and methods of the class and that of the classes derived. In EWCC, a cognitive weight of each attribute is considered to be 1.
The main problem in EWCC metric is that, every attribute holds the
same value but in general, cognitive load in understanding the
different types of attributes cannot be the same. So here, we are proposing a new metric namely Attribute Weighted Class Complexity
(AWCC). In AWCC, the cognitive weights have to be assigned for the attributes which are derived from the effort needed to understand
their data types. The proposed metric has been proved to be a better
measure of complexity of class with attributes through the case studies and experiments