Abstract: Laboratory experiments have been performed to investigate photocatalytic detoxification by using TiO2 photocatalyst for treating dairy effluent. Various operational parameters such as catalyst concentration, initial concentration, angle of tilt of solar flat plate reactor and flow rate were investigated. Results indicated that the photocatalytic detoxification process can efficiently treat dairy effluent. Experimental runs with dairy wastewater can be used to identify the optimum operational parameters to perform wastewater degradation on large scale for recycling purpose. Also effect of two different types of reactors on degradation process was analyzed.
Abstract: Fuel cells have become one of the major areas of
research in the academia and the industry. The goal of most fish
farmers is to maximize production and profits while holding labor
and management efforts to the minimum. Risk of fish kills, disease
outbreaks, poor water quality in most pond culture operations,
aeration offers the most immediate and practical solution to water
quality problems encountered at higher stocking and feeding rates.
Many units of aeration system are electrical units so using a
continuous, high reliability, affordable, and environmentally friendly
power sources is necessary. Aeration of water by using PEM fuel cell
power is not only a new application of the renewable energy, but
also, it provides an affordable method to promote biodiversity in
stagnant ponds and lakes. This paper presents a new design and
control of PEM fuel cell powered a diffused air aeration system for a
shrimp farm in Mersa Matruh in Egypt. Also Artificial intelligence
(AI) techniques control is used to control the fuel cell output power
by control input gases flow rate. Moreover the mathematical
modeling and simulation of PEM fuel cell is introduced. A
comparison study is applied between the performance of fuzzy logic
control (FLC) and neural network control (NNC). The results show
the effectiveness of NNC over FLC.
Abstract: An attempt has been made to develop a
seminumerical model to study temperature variations in dermal
layers of human limbs. The model has been developed for two
dimensional steady state case. The human limb has been assumed to
have elliptical cross section. The dermal region has been divided
into three natural layers namely epidermis, dermis and subdermal
tissues. The model incorporates the effect of important physiological
parameters like blood mass flow rate, metabolic heat generation, and
thermal conductivity of the tissues. The outer surface of the limb is
exposed to the environment and it is assumed that heat loss takes
place at the outer surface by conduction, convection, radiation, and
evaporation. The temperature of inner core of the limb also varies at
the lower atmospheric temperature. Appropriate boundary conditions
have been framed based on the physical conditions of the problem.
Cubic splines approach has been employed along radial direction and
Fourier series along angular direction to obtain the solution. The
numerical results have been computed for different values of
eccentricity resembling with the elliptic cross section of the human
limbs. The numerical results have been used to obtain the
temperature profile and to study the relationships among the various
physiological parameters.
Abstract: An HPLC-UV analytical method was developed to
determine ethylenediaminetetraacetic acid (EDTA) in dairy
wastewater and surface water. The optimizing separation was achieved
by reversed–phase ion-pair liquid chromatography on a C18 column
using methanol as mobile phase solvent, tetrabutylammonium bromide
as the ion-pair reagent in pH 3.3 formate buffer solution at a flow rate
of 0.9 mL min-1 with a UV detector at 265 nm. No interference of Ca,
Mg or NO3
- was detected. Method performance was evaluated in terms
of linearity, repeatability and reproducibility. The method detection
limit was 5 μg L-1. The contents of EDTA in dairy effluents were 72 ~
261 μg L-1 at a large dairy site. A change of EDTA concentration was
observed downstream of the dairy effluent discharge, but this was well
under the predicted no effect concentration for aquatic ecosystem.
Abstract: Water pipe network is installed underground and once equipped, it is difficult to recognize the state of pipes when the leak or burst happens. Accordingly, post management is often delayed
after the fault occurs. Therefore, the systematic fault management system of water pipe network is required to prevent the accident and
minimize the loss. In this work, we develop online fault detection system of water pipe network using data of pipes such as flow rate
or pressure. The transient model describing water flow in pipelines
is presented and simulated using MATLAB. The fault situations such
as the leak or burst can be also simulated and flow rate or pressure data when the fault happens are collected. Faults are detected using
statistical methods of fast Fourier transform and discrete wavelet transform, and they are compared to find which method shows the
better fault detection performance.
Abstract: Traffic flow in adverse weather conditions have been investigated in this study for general traffic, week day and week end traffic. The empirical evidence is strong in support of the view that rainfall affects macroscopic traffic flow parameters. Data generated from a basic highway section along J5 in Johor Bahru, Malaysia was synchronized with 161 rain events over a period of three months. This revealed a 4.90%, 6.60% and 11.32% reduction in speed for light rain, moderate rain and heavy rain conditions respectively. The corresponding capacity reductions in the three rainfall regimes are 1.08% for light rain, 6.27% for moderate rain and 29.25% for heavy rain. In the week day traffic, speed drops of 8.1% and 16.05% were observed for light and heavy conditions. The moderate rain condition speed increased by 12.6%. The capacity drops for week day traffic are 4.40% for light rain, 9.77% for moderate rain and 45.90% for heavy rain. The weekend traffic indicated speed difference between the dry condition and the three rainy conditions as 6.70% for light rain, 8.90% for moderate rain and 13.10% for heavy rain. The capacity changes computed for the weekend traffic were 0.20% in light rain, 13.90% in moderate rain and 16.70% in heavy rain. No traffic instabilities were observed throughout the observation period and the capacities reported for each rain condition were below the norain condition capacity. Rainfall has tremendous impact on traffic flow and this may have implications for shock wave propagation.
Abstract: The objective from this paper is to design a solar
thermal engine for space vehicles orbital control and electricity
generation. A computational model is developed for the prediction of
the solar thermal engine performance for different design parameters and conditions in order to enhance the engine efficiency. The engine is divided into two main subsystems. First, the concentrator dish
which receives solar energy from the sun and reflects them to the
cavity receiver. The second one is the cavity receiver which receives
the heat flux reflected from the concentrator and transfers heat to the
fluid passing over. Other subsystems depend on the application required from the engine. For thrust application, a nozzle is
introduced to the system for the fluid to expand and produce thrust.
Hydrogen is preferred as a working fluid in the thruster application.
Results model developed is used to determine the thrust for a
concentrator dish 4 meters in diameter (provides 10 kW of energy),
focusing solar energy to a 10 cm aperture diameter cavity receiver.
The cavity receiver outer length is 50 cm and the internal cavity is 47
cm in length. The suggested design material of the internal cavity is
tungsten to withstand high temperature. The thermal model and
analysis shows that the hydrogen temperature at the plenum reaches
2000oK after about 250 seconds for hot start operation for a flow rate
of 0.1 g/sec.Using solar thermal engine as an electricity generation
device on earth is also discussed. In this case a compressor and
turbine are used to convert the heat gained by the working fluid (air)
into mechanical power. This mechanical power can be converted into
electrical power by using a generator.
Abstract: In mechanical and environmental engineering, mixed
convection is a frequently encountered thermal fluid phenomenon
which exists in atmospheric environment, urban canopy flows, ocean
currents, gas turbines, heat exchangers, and computer chip cooling
systems etc... . This paper deals with a numerical investigation of
mixed convection in a vertical heated channel. This flow results from
the mixing of the up-going fluid along walls of the channel with the
one issued from a flat nozzle located in its entry section. The fluiddynamic
and heat-transfer characteristics of vented vertical channels
are investigated for constant heat-flux boundary conditions, a
Rayleigh number equal to 2.57 1010, for two jet Reynolds number
Re=3 103 and 2104 and the aspect ratio in the 8-20 range. The system
of governing equations is solved with a finite volumes method and an
implicit scheme. The obtained results show that the turbulence and
the jet-wall interaction activate the heat transfer, as does the drive of
ambient air by the jet. For low Reynolds number Re=3 103, the
increase of the aspect Ratio enhances the heat transfer of about 3%,
however; for Re=2 104, the heat transfer enhancement is of about
12%. The numerical velocity, pressure and temperature fields are
post-processed to compute the quantities of engineering interest such
as the induced mass flow rate, and average Nusselt number, in terms
of Rayleigh, Reynolds numbers and dimensionless geometric
parameters are presented.
Abstract: The paper depicts air velocity values, reproduced by laser Doppler anemometer (LDA) and ultrasonic anemometer (UA), relations with calculated ones from flow rate measurements using the gas meter which calibration uncertainty is ± (0.15 – 0.30) %. Investigation had been performed in channel installed in aerodynamical facility used as a part of national standard of air velocity. Relations defined in a research let us confirm the LDA and UA for air velocity reproduction to be the most advantageous measures. The results affirm ultrasonic anemometer to be reliable and favourable instrument for measurement of mean velocity or control of velocity stability in the velocity range of 0.05 m/s – 10 (15) m/s when the LDA used. The main aim of this research is to investigate low velocity regularities, starting from 0.05 m/s, including region of turbulent, laminar and transitional air flows. Theoretical and experimental results and brief analysis of it are given in the paper. Maximum and mean velocity relations for transitional air flow having unique distribution are represented. Transitional flow having distinctive and different from laminar and turbulent flow characteristics experimentally have not yet been analysed.
Abstract: This paper presented a novel combined cycle of air separation and natural gas liquefaction. The idea is that natural gas can be liquefied, meanwhile gaseous or liquid nitrogen and oxygen are produced in one combined cryogenic system. Cycle simulation and exergy analysis were performed to evaluate the process and thereby reveal the influence of the crucial parameter, i.e., flow rate ratio through two stages expanders β on heat transfer temperature difference, its distribution and consequent exergy loss. Composite curves for the combined hot streams (feeding natural gas and recycled nitrogen) and the cold stream showed the degree of optimization available in this process if appropriate β was designed. The results indicated that increasing β reduces temperature difference and exergy loss in heat exchange process. However, the maximum limit value of β should be confined in terms of minimum temperature difference proposed in heat exchanger design standard and heat exchanger size. The optimal βopt under different operation conditions corresponding to the required minimum temperature differences was investigated.
Abstract: Cavitation in pumps is known as the formation of
vapor bubbles due to pressure drop and collapsing these bubbles. In
some conditions, it has been observed that the formation of bubbles
occurs at the pressure side of centrifugal pump blades. In this study,
the formation of bubbles at the pressure side of blades has been
investigated. Water is used in this study as the fluid and performance
curves were depicted for different flow rates in an approximately
constant speed. The results show that when a centrifugal pump works
in low flow rates, a secondary flow namely recirculation starts to
begin. In this condition, separation of flow increases which causes
vortex formation and local pressure drop and eventually the
formation of vapor bubbles starts.
Abstract: Cardiovascular disease mostly in the form of atherosclerosis is responsible for 30% of all world deaths amounting to 17 million people per year. Atherosclerosis is due to the formation of plaque. The fatty plaque may be at risk of rupture, leading typically to stroke and heart attack. The plaque is usually associated with a high degree of lumen reduction, called a stenosis. The initiation and progression of the disease is strongly linked to the hemodynamic environment near the vessel wall. The aim of this study is to validate the flow of blood mimic through an arterial stenosis model with computational fluid dynamics (CFD) package. In experiment, an axisymmetric model constructed consists of contraction and expansion region that follow a mathematical form of cosine function. A 30% diameter reduction was used in this study. Particle image velocimetry (PIV) was used to characterize the flow. The fluid consists of rigid spherical particles suspended in waterglycerol- NaCl mixture. The particles with 20 μm diameter were selected to follow the flow of fluid. The flow at Re=155, 270 and 390 were investigated. The experimental result is compared with FLUENT simulated flow that account for viscous laminar flow model. The results suggest that laminar flow model was sufficient to predict flow velocity at the inlet but the velocity at stenosis throat at Re =390 was overestimated. Hence, a transition to turbulent regime might have been developed at throat region as the flow rate increases.
Abstract: The combustion chamber dimensions have important
effects on pollutant emission in furnaces as a direct result of
temperature distribution and maximum temperature value. In this
paper the pollutant emission and the temperature distribution in two
cylindrical furnaces with different dimensions (with similar length to
diameter ratio) in similar condition have been investigated
experimentally. The furnace fuel is gas oil that is used with three
different flow rates. The results show that in these two cases the
temperature increases to its maximum value quickly, and then
decreases slowly. The results also show that increase in fuel flow rate
cause to increase in NOx emission in each case, but this increase is
greater in small furnace. With increase in fuel flow rate, CO emission
decreases firstly, and then it increases. Combustion efficiency
reduces with increase in fuel flow rate but the rate of reduction in
small furnace is greater than large furnace. The results of axial
temperature distribution have been compared with those have been
obtained numerically and experimentally by Moghiman.
Abstract: Membrane distillation (MD) is a rising technology for
seawater or brine desalination process. In this work, an air gap
membrane distillation (AGMD) performance was investigated for
aqueous NaCl solution along with natural ground water and seawater.
In order to enhance the performance of the AGMD process in
desalination, that is, to get more flux, it is necessary to study the
effect of operating parameters on the yield of distillate water. The
influence of operational parameters such as feed flow rate, feed
temperature, feed salt concentration, coolant temperature and air gap
thickness on the membrane distillation (MD) permeation flux have
been investigated for low and high salt solution. the natural
application of ground water and seawater over 90 h continuous
operation, scale deposits observed on the membrane surface and
reduction in flux represents 23% for ground water and 60% for
seawater, in 90 h. This reduction was eliminated (less than 14 %) by
acidification of feed water. Hence, promote the research attention in
apply of AGMD for the ground water as well as seawater
desalination over today-s conventional RO operation.
Abstract: In this paper, three dimensional flow characteristic was
presented by a revision of an impeller of an axial turbo fan for
improving the airflow rate and the static pressure. TO consider an
incompressible steady three-dimensional flow, the RANS equations
are used as the governing equations, and the standard k-ε turbulence
model is chosen. The pitch angles of 44°, 54°, 59°, and 64° are
implemented for the numerical model. The numerical results show that
airflow rates of each pitch angle are 1,175 CMH, 1,270 CMH, 1,340
CMH, and 800 CMH, respectively. The difference of the static
pressure at impeller inlet and outlet are 120 Pa, 214 Pa, 242 Pa, and 60
Pa according to respective pitch angles. It means that the 59° of the
impeller pitch angle is optimal to improve the airflow rate and the
static pressure.
Abstract: A water reuse system in wetland paddy was simulated
to supply water for industrial in this paper. A two-tank model was employed to represent the return flow of the wetland paddy.Historical data were performed for parameter estimation and model verification. With parameters estimated from the data, the model was then used to simulate a reasonable return flow rate from the wetland
paddy. The simulation results show that the return flow ratio was 11.56% in the first crop season and 35.66% in the second crop
season individually; the difference may result from the heavy rainfall in the second crop season. Under the existent pond with surplus
active capacity, the water reuse ratio was 17.14%, and the water supplementary ratio was 21.56%. However, the pattern of rainfall, the
active capacity of the pond, and the rate of water treatment limit the
volume of reuse water. Increasing the irrigation water, dredging the
depth of pond before rainy season and enlarging the scale of module are help to develop water reuse system to support for the industrial
water use around wetland paddy.
Abstract: Energy and exergy study of air-water combined solar collector which is called dual purpose solar collector (DPSC) is investigated. The method of ε - NTU is used. Analysis is performed for triangle channels. Parameters like the air flow rate and water inlet temperature are studied. Results are shown that DPSC has better energy and exergy efficiency than single collector. In addition, the triangle passage with water inlet temperature of 60O C has shown better exergy and energy efficiency.
Abstract: This paper focuses on the development of bond graph
dynamic model of the mechanical dynamics of an excavating mechanism
previously designed to be used with small tractors, which are
fabricated in the Engineering Workshops of Jomo Kenyatta University
of Agriculture and Technology. To develop a mechanical dynamics
model of the manipulator, forward recursive equations similar to
those applied in iterative Newton-Euler method were used to obtain
kinematic relationships between the time rates of joint variables
and the generalized cartesian velocities for the centroids of the
links. Representing the obtained kinematic relationships in bondgraphic
form, while considering the link weights and momenta as
the elements led to a detailed bond graph model of the manipulator.
The bond graph method was found to reduce significantly the number
of recursive computations performed on a 3 DOF manipulator for a
mechanical dynamic model to result, hence indicating that bond graph
method is more computationally efficient than the Newton-Euler
method in developing dynamic models of 3 DOF planar manipulators.
The model was verified by comparing the joint torque expressions
of a two link planar manipulator to those obtained using Newton-
Euler and Lagrangian methods as analyzed in robotic textbooks. The
expressions were found to agree indicating that the model captures
the aspects of rigid body dynamics of the manipulator. Based on
the model developed, actuator sizing and valve sizing methodologies
were developed and used to obtain the optimal sizes of the pistons
and spool valve ports respectively. It was found that using the pump
with the sized flow rate capacity, the engine of the tractor is able to
power the excavating mechanism in digging a sandy-loom soil.
Abstract: The study of the fouling deposition of pink guava
juice (PGJ) is relatively new research compared to milk fouling
deposit. In this work, a new experimental set-up was developed to
imitate the fouling formation in heat exchanger, namely a continuous
flow experimental set-up heat exchanger. The new experimental setup
was operated under industrial pasteurization temperature of PGJ,
which was at 93°C. While the flow rate and pasteurization period
were based on the experimental capacity, which were 0.5 and 1
liter/min for the flow rate and the pasteurization period was set for 1
hour. Characterization of the fouling deposit was determined by
using various methods. Microstructure of the deposits was carried
out using ESEM. Proximate analyses were performed to determine
the composition of moisture, fat, protein, fiber, ash and carbohydrate
content. A study on the hardness and stickiness of the fouling deposit
was done using a texture analyzer. The presence of seedstone in pink
guava juice was also analyzed using a particle analyzer. The findings
shown that seedstone from pink guava juice ranging from 168 to
200μm and carbohydrate was found to be a major composition
(47.7% of fouling deposit consists of carbohydrate). Comparison
between the hardness and stickiness of the deposits at two different
flow rates showed that fouling deposits were harder and denser at
higher flow rate. Findings from this work provide basis knowledge
for further study on fouling and cleaning of PGJ.
Abstract: Water leakage is a serious problem in the maintenance of a waterworks facility. Monitoring the water flow rate is one way to locate leakage. However, conventional flowmeters such as the wet-type flowmeter and the clamp-on type ultrasonic flowmeter require additional construction for their installation and are therefore quite expensive. This paper proposes a novel estimation system for the flow rate in a water pipeline, which employs a vibration sensor. This assembly can be attached to any water pipeline without the need for additional high-cost construction. The vibration sensor is designed based on a condenser microphone. This sensor detects vibration caused by water flowing through a pipeline. It is possible to estimate the water flow rate by measuring the amplitude of the output signal from the vibration sensor. We confirmed the validity of the proposed sensing system experimentally.