Abstract: This study fabricates p-type Ni1−xO:Li/n-Si heterojunction solar cells (P+/n HJSCs) by using radio frequency (RF) magnetron sputtering and investigates the effect of substrate temperature on photovoltaic cell properties. Grazing incidence x-ray diffraction, four point probe, and ultraviolet-visible-near infrared discover the optoelectrical properties of p-Ni1-xO thin films. The results show that p-Ni1-xO thin films deposited at 300 oC has the highest grain size (22.4 nm), average visible transmittance (~42%), and electrical resistivity (2.7 Ωcm). However, the conversion efficiency of cell is shown only 2.33% which is lower than the cell (3.39%) fabricated at room temperature. This result can be mainly attributed to interfacial layer thickness (SiOx) reduces from 2.35 nm to 1.70 nm, as verified by high-resolution transmission electron microscopy.
Abstract: In this paper, the application of thermal spray
coatings in high speed shafts by a revolution up to 23000 RPM
has been studied. Gas compressor shafts are worn in contact
zone with journal therefore will be undersized. Wear
mechanisms of compressor shaft were identified. The
predominant wear mechanism is abrasion wear. The worn
surface was coated by hard WC-Co cermets using high
velocity oxy fuel (HVOF) after preparation. The shafts were in
satisfactory service in 8000h period. The metallurgical and
Tribological studies has been made on the worn and coated
shaft using optical microscopy, scanning electron microscopy
(SEM) and X-ray diffraction.
Abstract: In this study, structural, mechanical, thermal and
electrical properties of poly (lactic acid) (PLA) nanocomposites with
low-loaded (0-1.5 wt%) untreated, heat and nitric acid treated multiwalled
carbon nanotubes (MWCNTs) were studied. Among the
composites, untreated 0.5 wt % MWCNTs and acid-treated 1.0 wt%
MWCNTs reinforced PLA show the tensile strength and modulus
values higher than the others. These two samples along with pure
PLA exhibit the stable orthorhombic α-form, whilst other samples
reveal the less stable orthorhombic β-form, as demonstrated by X-ray
diffraction study. Differential scanning calorimetry reveals the
evolution of the mentioned different phases by controlled cooling and
discloses an enhancement of PLA crystallization by nanotubes
incorporation. Thermogravimetric analysis shows that the MWCNTs
loaded sample degraded faster than PLA. Surface resistivity of the
nanocomposites is found to be dropped drastically by a factor of 1013
with a low loading of MWCNTs (1.5 wt%).
Abstract: In this paper, the effect of addition the dune sand powder (DSP) on development of compressive strength and hydration of cement pastes was investigated as a function of water/binder ratio, was varied, on the one hand, the percentage of DSP and on the other, the fineness of DSP. In order to understand better the pozzolanic effect of dune sand powder in cement pastes, we followed the mixtures hydration (50% Pure Lime + 50% DSP) by X-ray diffraction. These mixtures the pastes present a hydraulic setting which is due to the formation of a C-S-H phase (calcium silicate hydrate). The latter is semi-crystallized. This study is a simplified approach to that of the mixtures (80% ordinary Portland cement + 20% DSP), in which the main reaction is the fixing of the lime coming from the cement hydration in the presence of DSP, to form calcium silicate hydrate semi-crystallized of second generation. The results proved that up to (20% DSP) as Portland cement replacement could be used with a fineness of 4000 cm²/g without affecting adversely the compressive strength. After 28 days, the compressive strength at 5, 10 and 15% DSP is superior to Portland cement, with an optimum effect for a percentage of the order of 5% to 10% irrespective of the w/b ratio and fineness of DSP.
Abstract: Copper based composites reinforced with WC and Ti
particles were prepared using planetary ball-mill. The experiment
was designed by using Taguchi technique and milling was carried out
in an air for several hours. The powder was characterized before and
after milling using the SEM, TEM and X-ray for microstructure and
for possible new phases. Microstructures show that milled particles
size and reduction in particle size depend on many parameters. The
distance d between planes of atoms estimated from X-ray powder
diffraction data and TEM image. X-ray diffraction patterns of the
milled powder did not show clearly any new peak or energy shift, but
the TEM images show a significant change in crystalline structure of
corporate on titanium in the composites.
Abstract: The Iranian bentonite was first characterized by
Scanning Electron Microscopy (SEM), Inductively Coupled Plasma
mass spectrometry (ICP-MS), X-ray fluorescence (XRF), X-ray
Diffraction (XRD) and BET. The bentonite was then treated
thermally between 150°C-250°C at 15min, 45min and 90min and
also was activated chemically with different concentration of
sulphuric acid (3N, 5N and 10N). Although the results of thermal
activated-bentonite didn-t show any considerable changes in specific
surface area and Cation Exchange Capacity (CEC), but the results of
chemical treated bentonite demonstrated that such properties have
been improved by acid activation process.
Abstract: The morphology, mineralogical and chemical
composition of a low-grade nickel ore from Mpumalanga, South
Africa, were studied by scanning electron microscope (SEM), X-ray
diffraction (XRD) and X-ray fluorescence (XRF), respectively. The
ore was subjected to atmospheric agitation leaching using sulphuric
acid to investigate the effects of acid concentration, leaching
temperature, leaching time and particle size on extraction of nickel
and cobalt. Analyses results indicated the ore to be a saprolitic nickel
laterite belonging to the serpentine group of minerals. Sulphuric acid
was found to be able to extract nickel from the ore. Increased acid
concentration and temperature only produced low amounts of nickel
but improved cobalt extraction. As high as 77.44% Ni was achieved
when leaching a -106+75μm fraction with 4.0M acid concentration at
25oC. The kinetics of nickel leaching from the saprolitic ore were
studied and the activation energy was determined to be 18.16kJ/mol.
This indicated that nickel leaching reaction was diffusion controlled.
Abstract: Noble metal participation in nanostructured
semiconductor catalysts has drawn much interest because of their
improved properties. Recently, it has been discussed by many
researchers that Ag participation in TiO2, CuO, ZnO semiconductors
showed improved photocatalytic and optical properties. In this
research, Ag/ZnO nanocomposite particles were prepared by
Ultrasonic Spray Pyrolysis(USP) Method. 0.1M silver and zinc
nitrate aqueous solutions were used as precursor solutions. The
Ag:Zn atomic ratio of the solution was selected 1:1. Experiments
were taken place under constant air flow of 400 mL/min at 800°C
furnace temperature. Particles were characterized by X-Ray
Diffraction (XRD), Scanning Electron Microscope (SEM) and
Energy Dispersive Spectroscopy (EDS). The crystallite sizes of Ag
and ZnO in composite particles are 24.6 nm, 19.7 nm respectively.
Although, spherical nanocomposite particles are in a range of 300-
800 nm, these particles are formed by the aggregation of primary
particles which are in a range of 20-60 nm.
Abstract: Waste problem is becoming a future problem all over the world. Magnesium wastes which can be used in recycling processes are produced by many industrial activities. Magnesium borates which have useful properties such as; high heat resistance, corrosion resistance, supermechanical strength, superinsulation, light weight, high coefficient of elasticity and so on. Addition, magnesium borates have great potential in the development of ceramic and detergents industry, whisker-reinforced composites, antiwear, and reducing friction additives.
In this study, using the starting materials of waste magnesium and H3BO3 the hydrothermal method was applied at a moderate temperature of 70oC with different reaction times. Several reaction times of waste magnesium to H3BO3 were selected as; 30, 60, 120, 240 minutes. After the synthesis, X-Ray Diffraction (XRD) and Fourier Transform Infrared Spectroscopy (FT-IR) techniques were applied to products. As a result, the forms of Admontite [MgO(B2O3)3.7(H2O)] and Mcallisterite [Mg2(B6O7(OH)6)2.9(H2O)] were synthesized.
Abstract: Thermoplastic starch, polylactic acid glycerol and
maleic anhydride (MA) were compounded with natural
montmorillonite (MMT) through a twin screw extruder to investigate
the effects of different loading of MMT on structure, thermal and
absorption behavior of the nanocomposites. X-ray diffraction analysis
(XRD) showed that sample with MMT loading 4phr exhibited
exfoliated structure while sample that contained MMT 8 phr
exhibited intercalated structure. FESEM images showed big lump
when MMT loading was at 8 phr. The thermal properties were
characterized by using differential scanning calorimeter (DSC). The
results showed that MMT increased melting temperature and
crystallization temperature of matrix but reduction in glass transition
temperature was observed Meanwhile the addition of MMT has
improved the water barrier property. The nanosize MMT particle is
also able to block a tortuous pathway for water to enter the starch
chain, thus reducing the water uptake and improved the physical
barrier of nanocomposite.
Abstract: Antimicrobial (AM) starch-based films were
developed by incorporating chitosan and lauric acid as antimicrobial
agent into starch-based film. Chitosan has wide range of applications
as a biomaterial, but barriers still exist to its broader use due to its
physical and chemical limitations. In this work, a series of
starch/chitosan (SC) blend films containing 8% of lauric acid was
prepared by casting method. The structure of the film was
characterized by Fourier transform infrared spectroscopy (FTIR), Xray
diffraction (XRD), and scanning electron microscopy (SEM).
The results indicated that there were strong interactions were present
between the hydroxyl groups of starch and the amino groups of
chitosan resulting in a good miscibility between starch and chitosan
in the blend films. Physical properties and optical properties of the
AM starch-based film were evaluated. The AM starch-based films
incorporated with chitosan and lauric acid showed an improvement in
water vapour transmission rate (WVTR) and addition of starch
content provided more transparent films while the yellowness of the
film attributed to the higher chitosan content. The improvement in
water barrier properties was mainly attributed to the hydrophobicity
of lauric acid and optimum chitosan or starch content. AM starch
based film also showed excellent oxygen barrier. Obtaining films
with good oxygen permeability would be an indication of the
potential use of these antimicrobial packaging as a natural packaging
and an alternative packaging to the synthetic polymer to protect food
from oxidation reactions
Abstract: This paper presented a theoretical and numerical investigation of the Compact Antenna Test Range (CATR) equipped with Super Hybrid Modulated Segmented Exponential Serrations (SHMSES). The investigation was based on diffraction theory and, more specifically, the Fresnel diffraction formulation. The CATR provides uniform illumination within the Fresnel region to test antenna. Application of serrated edges has been shown to be a good method to control diffraction at the edges of the reflectors. However, in order to get some insight into the positive effect of serrated edges a less rigorous analysis technique known as Physical Optics (PO) may be used. Ripple free and enhanced quiet zone width are observed for specific values of width and height modulation factors per serrations. The performance of SHMSE serrated reflector is evaluated in order to observe the effects of edge diffraction on the test zone fields.
Abstract: In order to avoid the potentially devastating
consequences of global warming and climate change, the carbon
dioxide “CO2" emissions caused due to anthropogenic activities must
be reduced considerably. This paper presents the first study
examining the feasibility of carbon sequestration in construction and
demolition “C&D" waste. Experiments were carried out in a self
fabricated Batch Reactor at 40ºC, relative humidity of 50-70%, and
flow rate of CO2 at 10L/min for 1 hour for water-to-solids ratio of 0.2
to 1.2. The effect of surface area was found by comparing the
theoretical extent of carbonation of two different sieve sizes (0.3mm
and 2.36mm) of C&D waste. A 38.44% of the theoretical extent of
carbonation equating to 4% CO2 sequestration extent was obtained
for C&D waste sample for 0.3mm sieve size. Qualitative,
quantitative and morphological analyses were done to validate
carbonate formation using X-ray diffraction “X.R.D.," thermal
gravimetric analysis “T.G.A., “X-Ray Fluorescence Spectroscopy
“X.R.F.," and scanning electron microscopy “S.E.M".
Abstract: A simple approach is demonstrated for growing large
scale, nearly vertically aligned ZnO nanowire arrays by thermal
oxidation method. To reveal effect of temperature on growth and
physical properties of the ZnO nanowires, gold coated zinc substrates
were annealed at 300 °C and 400 °C for 4 hours duration in air. Xray
diffraction patterns of annealed samples indicated a set of well
defined diffraction peaks, indexed to the wurtzite hexagonal phase of
ZnO. The scanning electron microscopy studies show formation of
ZnO nanowires having length of several microns and average of
diameter less than 500 nm. It is found that the areal density of wires
is relatively higher, when the annealing is carried out at higher
temperature i.e. at 400°C. From the field emission studies, the values
of the turn-on and threshold field, required to draw emission current
density of 10 μA/cm2 and 100 μA/cm2 are observed to be 1.2 V/μm
and 1.7 V/μm for the samples annealed at 300 °C and 2.9 V/μm and
3.7 V/μm for that annealed at 400 °C, respectively. The field
emission current stability, investigated over duration of more than 2
hours at the preset value of 1 μA, is found to be fairly good in both
cases. The simplicity of the synthesis route coupled with the
promising field emission properties offer unprecedented advantage
for the use of ZnO field emitters for high current density
applications.
Abstract: Platinum oxide nanoparticles were prepared by a
simple hydrothermal route and chemical reduction using
carbohydrates (Fructose and sucrose) as the reducing and
stabilizing agents. The crystallite size of these nanoparticles was
evaluated from X-ray diffraction (XRD), atomic force microscopy
(AFM) and transmission electron microscopy (TEM) and was
found to be 10 nm as shown in figure 1, which is the
demonstration of EM bright field and transmission electron
microscopy. The effect of carbohydrates on the morphology of the
nanoparticles was studied using TEM (Figure 1). The
nanoparticles (100 μg/ml) were administered to the Pseudomonas
Stutzeri and Lactobacillus cultures and the incubation was done at
35 oC for 24 hours. The nanocomposites exhibited interesting
inhibitory as well as bactericidal activity against P. Stutzeri and
and Lactobacillus species. Incorporation of nanoparticles also
increased the thermal stability of the carbohydrates.
Abstract: Nanowire arrays of copper with uniform diameters have
been synthesized by potentiostatic electrochemical metal deposition
(EMD) of copper sulphate and potassium chloride solution within
the nano-channels of porous Indium-Tin Oxide (ITO), also known as
Tin doped Indium Oxide templates. The nanowires developed were
fairly continuous with diameters ranging from 110-140 nm along
the entire length. Single as well as poly-crystalline copper wires
have been prepared by application of appropriate potential during the
EMD process. Scanning electron microscopy (SEM), high resolution
transmission electron microscopy (HRTEM), small angle electron
diffraction (SAED) and atomic force microscopy (AFM) were used
to characterize the synthesized nano wires at room temperature. The
electrochemical response of synthesized products was evaluated by
cyclic voltammetry while surface energy analysis was carried out
using a Goniometer.
Abstract: Bentonitic material from South Aswan, Egypt was evaluated in terms of mineral-ogy and chemical composition as bleaching clay in refining of transformer oil before and after acid activation and thermal treatment followed by acid leaching using HCl and H2SO4 for different contact times. Structural modification and refining power of bento-nite were investigated during modification by means of X-ray diffraction and infrared spectroscopy. The results revealed that the activated bentonite could be used for refining of transformer oil. The oil parameters such as; dielectric strength, viscosity and flash point had been improved. The dielectric breakdown strength of used oil increased from 29 kV for used oil treated with unactivated bentonite to 74 kV after treatment with activated bentonite. Kinematic Viscosity changed from 19 to 11 mm2 /s after treatment with activated bentonite. However, flash point achieved 149 ºC.
Abstract: Silver/polylactide nanocomposites (Ag/PLA-NCs) were
synthesized via chemical reduction method in diphase solvent. Silver
nitrate and sodium borohydride were used as a silver precursor
and reducing agent in the polylactide (PLA). The properties of
Ag/PLA-NCs were studied as a function of the weight percentages
of silver nanoparticles (8, 16 and 32 wt% of Ag-NPs) relative to
the weight of PLA. The Ag/PLA-NCs were characterized by Xray
diffraction (XRD), transmission electron microscopy (TEM),
electro-optical microscopy (EOM), UV-visible spectroscopy (UV-vis)
and Fourier transform infrared spectroscopy (FT-IR). XRD patterns
confirmed that Ag-NPs crystallographic planes were face centered
cubic (fcc) type. TEM images showed that mean diameters of Ag-NPs
were 3.30, 3.80 and 4.80 nm. Electro-optical microscopy revealed
excellent dispersion and interaction between Ag-NPs and PLA films.
The generation of silver nanoparticles was confirmed from the UVvisible
spectra. FT-IR spectra showed that there were no significant
differences between PLA and Ag/PLA-NCs films. The synthesized
Ag/PLA-NCs were stable in organic solution over a long period of
time without sign of precipitation.
Abstract: Wheat has a bimodal starch granule population and the dependency of the rate of enzymatic hydrolysis on particle size has been investigated. Ungelatinised wheaten starch granules were separated into two populations by sedimentation and decantation. Particle size was analysed by laser diffraction and morphological characteristics were viewed using SEM. The sedimentation technique though lengthy, gave satisfactory separation of the granules. Samples (10μm and original) were digested with a-amylase using a dialysis model. Granules of 10μm (p10μm. Moreover, the digestion rate was dependent on particle size whereby smaller granules produced higher rate of release. The methodology and results reported here can be used as a basis for further evaluations designed to delay the release of glucose during the digestion of native starches.
Abstract: Low oxygen content vanadium powder was
prepared by hydrogenation dehydrogenization (HDH). The
effect of purification treatment on hydrogen absorption kinetics
of dendritic vanadium was tested, and the effects of milling
technique on powder yield and grain size were studied. The
crystal phase, oxygen and nitrgen content, and grain size of
prepared powder were characterized and analyzed by X-ray
diffraction (XRD), oxygen and nitrogen analyzer and grain size
analyzer. The results show that the alkaline cleaning can
improve the hydrogen absorption of vanadium. The yield of
vanadium hydride powder can reach as high as 90% by 4h
ball-milling, The resultant product also have an oxygen content
less than 600μg/g, and the grain size is smaller than 37μm.
Meanwhile, the XRD results show that the phase of hydride
vanadium powder is mainly VH0.81. After a hydrogen
desorption treatment in vacuum at 700Ôäâ, the phase of the
powder converts into V and a little of V2H.