Abstract: In recent years, there have been attempts to store
natural gas in adsorptive form. This is called adsorptive natural gas,
or ANG. The problem with this technology is the low sorption
capacity. The purpose is to achieve compressed natural gas (CNG)
capacity of 230 V/V. Further research is required to achieve such
target. Several research studies have been performed with this target;
through either the modification or development of new sorbents or
the optimization of the operation sorption process itself. In this work,
storage of methane on molecular sieves 5A and 13X was studied on
dry basis, and on wet basis to certain extent. The temperature and the
pressure dynamics were investigated. The results indicated that
regardless of the charge pressure, the time for the peak temperature
during the methane charge process is always the same. This can be
used as a characteristic of the adsorbent. The total achieved
deliveries using molecular sieves were much lower than that of
activated carbons; 53.0 V/V for the case of 13X molecular sieves and
43 V/V for the case of 5A molecular sieves, both at 2oC and 4 MPa
(580 psi). Investigation of charge pressure dynamic using wet
molecular sieves at 2oC and a mass ratio of 0.5, revealed slowness of
the process and unexpected behavior.
Abstract: Persian (Farsi) script is totally cursive and each character is written in several different forms depending on its former and later characters in the word. These complexities make automatic handwriting recognition of Persian a very hard problem and there are few contributions trying to work it out. This paper presents a novel practical approach to online recognition of Persian handwriting which is based on representation of inputs and patterns with very simple visual features and comparison of these simple terms. This recognition approach is tested over a set of Persian words and the results have been quite acceptable when the possible words where unknown and they were almost all correct in cases that the words where chosen from a prespecified list.
Abstract: The absolute Cu atoms density in Cu(2S1/22P1/2)
ground state has been measured by Resonance Optical Absorption
(ROA) technique in a DC magnetron sputtering deposition with
argon. We measured these densities under variety of operation
conditions: pressure from 0.6 μbar to 14 μbar, input power from
10W to 200W and N2 mixture from 0% to 100%. For measuring the
gas temperature, we used the simulation of N2 rotational spectra
with a special computer code. The absolute number density of Cu
atoms decreases with increasing the N2 percentage of buffer gas at
any conditions of this work. But the deposition rate, is not decreased
with the same manner. The deposition rate variation is very small
and in the limit of quartz balance measuring equipment accuracy. So
we conclude that decrease in the absolute number density of Cu
atoms in magnetron plasma has not a big effect on deposition rate,
because the diffusion of Cu atoms to the chamber volume and
deviation of Cu atoms from direct path (towards the substrate)
decreases with increasing of N2 percentage of buffer gas. This is
because of the lower mass of N2 atoms compared to the argon ones.
Abstract: Single crystals of Magnesium alloys such as Mg-1Al,
Mg-1Zn-0.5Y, Mg-3Li, and AZ31 alloys were successfully fabricated in this study by employing the modified Bridgman method. Single
crystals of pure Mg were also made in this study. To determine the exact orientation of crystals, Laue back-reflection method and pole figure measurement were carried out on each single crystal. Dimensions of single crystals were 10 mm in diameter and 120 mm in
length. Hardness and compression tests were conducted and the results
revealed that hardness and the strength strongly depended on the
orientation. The closer to basal one the orientation was, the higher hardness and compressive strength were. The effect of alloying was
not higher than that of orientation. After compressive deformation of single crystals, the orientation of the crystals was found to rotate and to be parallel to the basal orientation.
Abstract: System MEMORI automatically detects and recognizes
rotated and/or rescaled versions of the objects of a database within
digital color images with cluttered background. This task is accomplished
by means of a region grouping algorithm guided by heuristic
rules, whose parameters concern some geometrical properties and the
recognition score of the database objects. This paper focuses on the
strategies implemented in MEMORI for the estimation of the heuristic
rule parameters. This estimation, being automatic, makes the system
a self configuring and highly user-friendly tool.
Abstract: During last decades, developing multi-objective
evolutionary algorithms for optimization problems has found
considerable attention. Flexible job shop scheduling problem, as an
important scheduling optimization problem, has found this attention
too. However, most of the multi-objective algorithms that are
developed for this problem use nonprofessional approaches. In
another words, most of them combine their objectives and then solve
multi-objective problem through single objective approaches. Of
course, except some scarce researches that uses Pareto-based
algorithms. Therefore, in this paper, a new Pareto-based algorithm
called controlled elitism non-dominated sorting genetic algorithm
(CENSGA) is proposed for the multi-objective FJSP (MOFJSP). Our
considered objectives are makespan, critical machine work load, and
total work load of machines. The proposed algorithm is also
compared with one the best Pareto-based algorithms of the literature
on some multi-objective criteria, statistically.
Abstract: The amount and heterogeneity of data in biomedical research, notably in interdisciplinary research, requires new methods for the collection, presentation and analysis of information. Important data from laboratory experiments as well as patient trials are available but come out of distributed resources. The Charite Medical School in Berlin has established together with the German Research Foundation (DFG) a new information service center for kidney diseases and transplantation (Open European Nephrology Science Centre - OpEN.SC). The system is based on a service-oriented architecture (SOA) with main and auxiliary modules arranged in four layers. To improve the reuse and efficient arrangement of the services the functionalities are described as business processes using the standardised Business Process Execution Language (BPEL).
Abstract: A fast settling multipath CMOS OTA for high speed
switched capacitor applications is presented here. With the basic
topology similar to folded-cascode, bandwidth and DC gain of the
OTA are enhanced by adding extra paths for signal from input to
output. Designed circuit is simulated with HSPICE using level 49
parameters (BSIM 3v3) in 0.35mm standard CMOS technology. DC
gain achieved is 56.7dB and Unity Gain Bandwidth (UGB) obtained
is 1.15GHz. These results confirm that adding extra paths for signal
can improve DC gain and UGB of folded-cascode significantly.
Abstract: The passive electrical properties of a tissue depends
on the intrinsic constituents and its structure, therefore by measuring
the complex electrical impedance of the tissue it might be possible to
obtain indicators of the tissue state or physiological activity [1].
Complete bio-impedance information relative to physiology and
pathology of a human body and functional states of the body tissue or
organs can be extracted by using a technique containing a fourelectrode
measurement setup. This work presents the estimation
measurement setup based on the four-electrode technique. First, the
complex impedance is estimated by three different estimation
techniques: Fourier, Sine Correlation and Digital De-convolution and
then estimation errors for the magnitude, phase, reactance and
resistance are calculated and analyzed for different levels of
disturbances in the observations. The absolute values of relative
errors are plotted and the graphical performance of each technique is
compared.
Abstract: In this study the integration of an absorption heat
pump (AHP) with the concentration section of an industrial pulp and
paper process is investigated using pinch technology. The optimum
design of the proposed water-lithium bromide AHP is then achieved
by minimizing the total annual cost. A comprehensive optimization is
carried out by relaxation of all stream pressure drops as well as heat
exchanger areas involving in AHP structure. It is shown that by
applying genetic algorithm optimizer, the total annual cost of the
proposed AHP is decreased by 18% compared to one resulted from
simulation.
Abstract: Question answering (QA) aims at retrieving precise information from a large collection of documents. Most of the Question Answering systems composed of three main modules: question processing, document processing and answer processing. Question processing module plays an important role in QA systems to reformulate questions. Moreover answer processing module is an emerging topic in QA systems, where these systems are often required to rank and validate candidate answers. These techniques aiming at finding short and precise answers are often based on the semantic relations and co-occurrence keywords. This paper discussed about a new model for question answering which improved two main modules, question processing and answer processing which both affect on the evaluation of the system operations. There are two important components which are the bases of the question processing. First component is question classification that specifies types of question and answer. Second one is reformulation which converts the user's question into an understandable question by QA system in a specific domain. The objective of an Answer Validation task is thus to judge the correctness of an answer returned by a QA system, according to the text snippet given to support it. For validating answers we apply candidate answer filtering, candidate answer ranking and also it has a final validation section by user voting. Also this paper described new architecture of question and answer processing modules with modeling, implementing and evaluating the system. The system differs from most question answering systems in its answer validation model. This module makes it more suitable to find exact answer. Results show that, from total 50 asked questions, evaluation of the model, show 92% improving the decision of the system.
Abstract: Stable bacterial polymorphism on a single limiting resource may appear if between the evolved strains metabolic interactions take place that allow the exchange of essential nutrients [8]. Towards an attempt to predict the possible outcome of longrunning evolution experiments, a network based on the metabolic capabilities of homogeneous populations of every single gene knockout strain (nodes) of the bacterium E. coli is reconstructed. Potential metabolic interactions (edges) are allowed only between strains of different metabolic capabilities. Bacterial communities are determined by finding cliques in this network. Growth of the emerged hypothetical bacterial communities is simulated by extending the metabolic flux balance analysis model of Varma et al [2] to embody heterogeneous cell population growth in a mutual environment. Results from aerobic growth on 10 different carbon sources are presented. The upper bounds of the diversity that can emerge from single-cloned populations of E. coli such as the number of strains that appears to metabolically differ from most strains (highly connected nodes), the maximum clique size as well as the number of all the possible communities are determined. Certain single gene deletions are identified to consistently participate in our hypothetical bacterial communities under most environmental conditions implying a pattern of growth-condition- invariant strains with similar metabolic effects. Moreover, evaluation of all the hypothetical bacterial communities under growth on pyruvate reveals heterogeneous populations that can exhibit superior growth performance when compared to the performance of the homogeneous wild-type population.
Abstract: Pressure waves and Water Hammer occur in a
pumping system when valves are closed or opened suddenly or in
the case of sudden failure of pumps. Determination of maximum
water hammer is considered one of the most important technical
and economical items of which engineers and designers of
pumping stations and conveyance pipelines should take care.
Hammer Software is a recent application used to simulate water
hammer. The present study focuses on determining significance of
each input parameter of the application relative to the maximum
amount of water hammer estimated by the software. The study
determines estimated maximum water hammer variations due to
variations of input parameters including water temperature, pipe
type, thickness and diameter, electromotor rpm and power, and
moment of inertia of electromotor and pump. In our study,
Kuhrang Pumping Station was modeled using WaterGEMS
Software. The pumping station is characterized by total discharge
of 200 liters per second, dynamic height of 194 meters and 1.5
kilometers of steel conveyance pipeline and transports water to
Cheshme Morvarid for farmland irrigation. The model was run in
steady hydraulic condition and transferred to Hammer Software.
Then, the model was run in several unsteady hydraulic conditions
and sensitivity of maximum water hammer to each input parameter
was calculated. It is shown that parameters to which maximum
water hammer is most sensitive are moment of inertia of pump and
electromotor, diameter, type and thickness of pipe and water
temperature, respectively.
Abstract: The electrical interaction between two axisymmetric
spheroidal particles in an electrolyte solution is examined numerically.
A Galerkin finite element method combined with a Newton-Raphson
iteration scheme is proposed to evaluate the spatial variation in the
electrical potential, and the result obtained used to estimate the
interaction energy between two particles. We show that if the surface
charge density is fixed, the potential gradient is larger at a point, which
has a larger curvature, and if surface potential is fixed, surface charge
density is proportional to the curvature. Also, if the total interaction
energy against closest surface-to-surface curve exhibits a primary
maximum, the maximum follows the order (oblate-oblate) >
(sphere-sphere)>(oblate-prolate)>(prolate-prolate), and if the curve
has a secondary minimum, the absolute value of the minimum follows
the same order.
Abstract: The purposes of this study are 1) to identify
learning styles of university students in Bangkok, and 2) to study
the frequency of the relevant instructional context of the identified
learning styles. Learning Styles employed in this study are those of
Honey and Mumford, which include 1) Reflectors, 2) Theorists, 3)
Pragmatists, and 4) Activists. The population comprises 1383
students and 5 lecturers. Research tools are 2 questionnaires – one
used for identifying students- learning styles, and the other used for
identifying the frequency of the relevant instructional context of
the identified learning styles.
The research findings reveal that 32.30 percent - are Activists,
while 28.10 percent are Theorists, 20.10 are Reflectors, and 19.50
are Pragmatists. In terms of the relevant instructional context of the
identified 4 learning styles, it is found that the frequency level of
the instructional context is totally in high level. Moreover, 2 lists of
the context being conducted most frequently are 'Lead'in activity
to review background knowledge,- and 'Information retrieval
report.' And these two activities serve the learning styles of
theorists and activists. It is, therefore, suggested that more
instructional context supporting the activists, the majority of the
population, learning best by doing, as well as emotional learning
situation should be added.
Abstract: Detection of player identity is challenging task in sport video content analysis. In case of soccer video player number recognition is effective and precise solution. Jersey numbers can be considered as scene text and difficulties in localization and recognition appear due to variations in orientation, size, illumination, motion etc. This paper proposed new method for player number localization and recognition. By observing hue, saturation and value for 50 different jersey examples we noticed that most often combination of low and high saturated pixels is used to separate number and jersey region. Image segmentation method based on this observation is introduced. Then, novel method for player number localization based on internal contours is proposed. False number candidates are filtered using area and aspect ratio. Before OCR processing extracted numbers are enhanced using image smoothing and rotation normalization.
Abstract: One very interesting field of research in Pattern Recognition that has gained much attention in recent times is Gesture Recognition. In this paper, we consider a form of dynamic hand gestures that are characterized by total movement of the hand (arm) in space. For these types of gestures, the shape of the hand (palm) during gesturing does not bear any significance. In our work, we propose a model-based method for tracking hand motion in space, thereby estimating the hand motion trajectory. We employ the dynamic time warping (DTW) algorithm for time alignment and normalization of spatio-temporal variations that exist among samples belonging to the same gesture class. During training, one template trajectory and one prototype feature vector are generated for every gesture class. Features used in our work include some static and dynamic motion trajectory features. Recognition is accomplished in two stages. In the first stage, all unlikely gesture classes are eliminated by comparing the input gesture trajectory to all the template trajectories. In the next stage, feature vector extracted from the input gesture is compared to all the class prototype feature vectors using a distance classifier. Experimental results demonstrate that our proposed trajectory estimator and classifier is suitable for Human Computer Interaction (HCI) platform.
Abstract: In this paper, the dam-reservoir interaction is
analyzed using a finite element approach. The fluid is assumed to be
incompressible, irrotational and inviscid. The assumed boundary
conditions are that the interface of the dam and reservoir is vertical
and the bottom of reservoir is rigid and horizontal. The governing
equation for these boundary conditions is implemented in the
developed finite element code considering the horizontal and vertical
earthquake components. The weighted residual standard Galerkin
finite element technique with 8-node elements is used to discretize
the equation that produces a symmetric matrix equation for the damreservoir
system. A new boundary condition is proposed for
truncating surface of unbounded fluid domain to show the energy
dissipation in the reservoir, through radiation in the infinite upstream
direction. The Sommerfeld-s and perfect damping boundary
conditions are also implemented for a truncated boundary to compare
with the proposed far end boundary. The results are compared with
an analytical solution to demonstrate the accuracy of the proposed
formulation and other truncated boundary conditions in modeling the
hydrodynamic response of an infinite reservoir.
Abstract: The present study was performed in Musa bay (northern part of the Persian Gulf) around the coastal area of Bandare-Imam Khomeini and Razi Petrochemical Companies. Sediment samples and effluent samples were collected from the selected stations, from June 2009 to June 2010. The samples were analyzed to determine the degree of hydrocarbon contamination. The average level of TPH concentration in the study area was more than the natural background value at all of the stations, especially at station BI1 which was the main effluent outlet of Bandar-e- Imam Khomeini petrochemical company. Also the concentration of total petroleum hydrocarbon was monitored in the effluents of aforementioned petrochemical companies and the results showed that the concentration of TPH in the effluents of Bandar-e- Imam Khomeini petrochemical company was greater than Razi petrochemical company which is may be related to the products of Bandar-e- Imam Khomeini petrochemical company (aromatics, polymers, chemicals, fuel).
Abstract: In this paper fatigue crack initiation and propagation in notched plate under constant amplitude loading through tensile residual stress field of 2024 T351 Al-alloy plate were investigated. Residual stress field was generated by plastic deformation using finite element method (FEM) where isotropic hardening in Von Mises model was applied. Simulation of fatigue behavior was made on AFGROW code. It was shown that the fatigue crack initiation and propagation were affected by level of residual stress filed. In this investigation, the presence of tensile residual stresses at notch (hole) reduces considerably the total fatigue life. It was shown that the decreasing in stress reduces the fatigue crack growth rates.