Abstract: In the present work steady inviscid hypersonic flows
are calculated by approximate Method. Maslens' inverse method is the chosen approximate method. For the inverse problem, parabolic
shock shape is chosen for the two-dimensional flow, and the body shape and flow field are calculated using Maslen's method. For the axisymmetric inverse problem paraboloidal shock is chosen and the
surface distribution of pressure is obtained.
Abstract: Two-dimensional Direct Numerical Simulation (DNS)
of high Schmidt number mass transfer in a convective flow environment
(Rayleigh-B'enard) is carried out and results are compared to
experimental data. A fourth-order accurate WENO-scheme has been
used for scalar transport in order to aim for a high accuracy in areas
of high concentration gradients. It was found that the typical spatial
distance between downward plumes of cold high concentration water
and the eddy size are in good agreement with experiments using a
combined PIV-LIF technique for simultaneous and spatially synoptic
measurements of 2D velocity and concentration fields.
Abstract: Flows over a harmonically oscillating NACA 0012
airfoil are simulated here using a two-dimensional, unsteady,
incompressibleNavier-Stokes solver.Both pure-plunging and
pitching-plunging combined oscillations are considered at a Reynolds
number of 5000. Special attention is paid to the vortex shedding and
interaction mechanism of the motions. For all the simulations
presented here, the reduced frequency (k) is fixed at a value of 2.5
and plunging amplitude (h) is selected to be in the range of 0.2-0.5.
The simulation results show that the interaction mechanism between
the leading and trailing edge vortices has a decisive effect on the
values of the resulting thrust and propulsive efficiency.
Abstract: A large number of chemical, bio-chemical and pollution-control processes use heterogeneous fixed-bed reactors. The use of finite hollow cylindrical catalyst pellets can enhance conversion levels in such reactors. The absence of the pellet core can significantly lower the diffusional resistance associated with the solid phase. This leads to a better utilization of the catalytic material, which is reflected in the higher values for the effectiveness factor, leading ultimately to an enhanced conversion level in the reactor. It is however important to develop a rigorous heterogeneous model for the reactor incorporating the two-dimensional feature of the solid phase owing to the presence of the finite hollow cylindrical catalyst pellet. Presently, heterogeneous models reported in the literature invariably employ one-dimension solid phase models meant for spherical catalyst pellets. The objective of the paper is to present a rigorous model of the fixed-bed reactors containing finite hollow cylindrical catalyst pellets. The reaction kinetics considered here is the widely used Michaelis–Menten kinetics for the liquid-phase bio-chemical reactions. The reaction parameters used here are for the enzymatic degradation of urea. Results indicate that increasing the height to diameter ratio helps to improve the conversion level. On the other hand, decreasing the thickness is apparently not as effective. This could however be explained in terms of the higher void fraction of the bed that causes a smaller amount of the solid phase to be packed in the fixed-bed bio-chemical reactor.
Abstract: The incidence of mechanical fracture of an
automobile piston rings prompted development of fracture analysis
method on this case. The three rings (two compression rings and one
oil ring) were smashed into several parts during the power-test (after
manufacturing the engine) causing piston and liner to be damaged.
The radial and oblique cracking happened on the failed piston rings.
The aim of the fracture mechanics simulations presented in this paper
was the calculation of particular effective fracture mechanics
parameters, such as J-integrals and stress intensity factors. Crack
propagation angles were calculated as well. Two-dimensional
fracture analysis of the first compression ring has been developed in
this paper using ABAQUS CAE6.5-1 software. Moreover, SEM
fractography was developed on fracture surfaces and is discussed in
this paper. Results of numerical calculations constitute the basis for
further research on real object.
Abstract: This paper describes a method to measure and
compensate a 4 axes ultra-precision machine tool that generates micro
patterns on the large surfaces. The grooving machine is usually used
for making a micro mold for many electrical parts such as a light guide
plate for LCD and fuel cells. The ultra precision machine tool has three
linear axes and one rotational table. Shaping is usually used to
generate micro patterns. In the case of 50 μm pitch and 25 μm height
pyramid pattern machining with a 90° wedge angle bite, one of linear
axis is used for long stroke motion for high cutting speed and other
linear axis are used for feeding. The triangular patterns can be
generated with many times of long stroke of one axis. Then 90°
rotation of work piece is needed to make pyramid patterns with
superposition of machined two triangular patterns.
To make a two dimensional positioning error, straightness of two
axes in out of plane, squareness between the each axis are important.
Positioning errors, straightness and squarness were measured by laser
interferometer system. Those were compensated and confirmed by
ISO230-6. One of difficult problem to measure the error motions is
squareness or parallelism of axis between the rotational table and
linear axis. It was investigated by simultaneous moving of rotary table
and XY axes. This compensation method is introduced in this paper.
Abstract: In 1990 [1] the subband-DFT (SB-DFT) technique was proposed. This technique used the Hadamard filters in the decomposition step to split the input sequence into low- and highpass sequences. In the next step, either two DFTs are needed on both bands to compute the full-band DFT or one DFT on one of the two bands to compute an approximate DFT. A combination network with correction factors was to be applied after the DFTs. Another approach was proposed in 1997 [2] for using a special discrete wavelet transform (DWT) to compute the discrete Fourier transform (DFT). In the first step of the algorithm, the input sequence is decomposed in a similar manner to the SB-DFT into two sequences using wavelet decomposition with Haar filters. The second step is to perform DFTs on both bands to obtain the full-band DFT or to obtain a fast approximate DFT by implementing pruning at both input and output sides. In this paper, the wavelet-based DFT (W-DFT) with Haar filters is interpreted as SB-DFT with Hadamard filters. The only difference is in a constant factor in the combination network. This result is very important to complete the analysis of the W-DFT, since all the results concerning the accuracy and approximation errors in the SB-DFT are applicable. An application example in spectral analysis is given for both SB-DFT and W-DFT (with different filters). The adaptive capability of the SB-DFT is included in the W-DFT algorithm to select the band of most energy as the band to be computed. Finally, the W-DFT is extended to the two-dimensional case. An application in image transformation is given using two different types of wavelet filters.
Abstract: Background: Tissue Doppler Echocardiography
(TDE) assesses diastolic function more accurately than routine pulse
Doppler echo. Assessment of the effects of dynamic and static
exercises on the heart by using TDE can provides new information
about the athlete-s heart syndrome. Methods: This study was
conducted on 20 elite wrestlers, 14 endurance runners at national
level and 21 non-athletes as the control group. Participants underwent
two-dimensional echocardiography, standard Doppler and TDE.
Results: Wrestlers had the highest left ventricular mass index, enddiastolic
inter-ventricular septum thickness and left ventricular
Posterior wall thickness. Runners had the highest Left ventricular
end-diastolic volume, LV ejection fraction, stroke volume and
cardiac output. In TDE, the early diastolic velocity of mitral annulus
to the late diastolic velocity ratio in athletic groups was greater than
the controls with no significant difference. Conclusion: In spite of
cardiac morphological changes in athletes, TDE shows that cardiac
diastolic function won-t be adversely affected.
Abstract: In theoretical computer science, the Turing machine has played a number of important roles in understanding and exploiting basic concepts and mechanisms in computing and information processing [20]. It is a simple mathematical model of computers [9]. After that, M.Blum and C.Hewitt first proposed two-dimensional automata as a computational model of two-dimensional pattern processing, and investigated their pattern recognition abilities in 1967 [7]. Since then, a lot of researchers in this field have been investigating many properties about automata on a two- or three-dimensional tape. On the other hand, the question of whether processing fourdimensional digital patterns is much more difficult than two- or threedimensional ones is of great interest from the theoretical and practical standpoints. Thus, the study of four-dimensional automata as a computasional model of four-dimensional pattern processing has been meaningful [8]-[19],[21]. This paper introduces a cooperating system of four-dimensional finite automata as one model of four-dimensional automata. A cooperating system of four-dimensional finite automata consists of a finite number of four-dimensional finite automata and a four-dimensional input tape where these finite automata work independently (in parallel). Those finite automata whose input heads scan the same cell of the input tape can communicate with each other, that is, every finite automaton is allowed to know the internal states of other finite automata on the same cell it is scanning at the moment. In this paper, we mainly investigate some accepting powers of a cooperating system of eight- or seven-way four-dimensional finite automata. The seven-way four-dimensional finite automaton is an eight-way four-dimensional finite automaton whose input head can move east, west, south, north, up, down, or in the fu-ture, but not in the past on a four-dimensional input tape.
Abstract: In this paper, for the first time, a two-dimensional
(2D) analytical drain current model for sub-100 nm multi-layered
gate material engineered trapezoidal recessed channel (MLGMETRC)
MOSFET: a novel design is presented and investigated using
ATLAS and DEVEDIT device simulators, to mitigate the large gate
leakages and increased standby power consumption that arise due to
continued scaling of SiO2-based gate dielectrics. The twodimensional
(2D) analytical model based on solution of Poisson-s
equation in cylindrical coordinates, utilizing the cylindrical
approximation, has been developed which evaluate the surface
potential, electric field, drain current, switching metric: ION/IOFF
ratio and transconductance for the proposed design. A good
agreement between the model predictions and device simulation
results is obtained, verifying the accuracy of the proposed analytical
model.
Abstract: A method for solving linear and non-linear Goursat
problem is given by using the two-dimensional differential transform
method. The approximate solution of this problem is calculated in
the form of a series with easily computable terms and also the exact
solutions can be achieved by the known forms of the series solutions.
The method can easily be applied to many linear and non-linear
problems and is capable of reducing the size of computational work.
Several examples are given to demonstrate the reliability and the
performance of the presented method.
Abstract: Cluster analysis is the name given to a diverse collection of techniques that can be used to classify objects (e.g. individuals, quadrats, species etc). While Kohonen's Self-Organizing Feature Map (SOFM) or Self-Organizing Map (SOM) networks have been successfully applied as a classification tool to various problem domains, including speech recognition, image data compression, image or character recognition, robot control and medical diagnosis, its potential as a robust substitute for clustering analysis remains relatively unresearched. SOM networks combine competitive learning with dimensionality reduction by smoothing the clusters with respect to an a priori grid and provide a powerful tool for data visualization. In this paper, SOM is used for creating a toroidal mapping of two-dimensional lattice to perform cluster analysis on results of a chemical analysis of wines produced in the same region in Italy but derived from three different cultivators, referred to as the “wine recognition data" located in the University of California-Irvine database. The results are encouraging and it is believed that SOM would make an appealing and powerful decision-support system tool for clustering tasks and for data visualization.
Abstract: A two-dimensional moving mesh algorithm is developed to simulate the general motion of two rotating bodies with relative translational motion. The grid includes a background grid and two sets of grids around the moving bodies. With this grid arrangement rotational and translational motions of two bodies are handled separately, with no complications. Inter-grid boundaries are determined based on their distances from two bodies. In this method, the overset concept is applied to hybrid grid, and flow variables are interpolated using a simple stencil. To evaluate this moving mesh algorithm unsteady Euler flow is solved for different cases using dual-time method of Jameson. Numerical results show excellent agreement with experimental data and other numerical results. To demonstrate the capability of present algorithm for accurate solution of flow fields around moving bodies, some benchmark problems have been defined in this paper.
Abstract: In this paper optical code-division multiple-access (OCDMA) packet network is considered, which offers inherent security in the access networks. Two types of random access protocols are proposed for packet transmission. In protocol 1, all distinct codes and in protocol 2, distinct codes as well as shifted versions of all these codes are used. O-CDMA network performance using optical orthogonal codes (OOCs) 1-D and two-dimensional (2-D) wavelength/time single-pulse-per-row (W/T SPR) codes are analyzed. The main advantage of using 2-D codes instead of onedimensional (1-D) codes is to reduce the errors due to multiple access interference among different users. In this paper, correlation receiver is considered in the analysis. Using analytical model, we compute and compare packet-success probability for 1-D and 2-D codes in an O-CDMA network and the analysis shows improved performance with 2-D codes as compared to 1-D codes.
Abstract: The finite-difference time-domain (FDTD) method is
one of the most widely used computational methods in
electromagnetic. This paper describes the design of two-dimensional
(2D) FDTD simulation software for transverse magnetic (TM)
polarization using Berenger's split-field perfectly matched layer
(PML) formulation. The software is developed using Matlab
programming language. Numerical examples validate the software.
Abstract: The solitary wave solution of the quadratic nonlinear Schrdinger equation is determined by the iterative method called Petviashvili method. This solution is also used for the initial condition for the time evolution to study the stability analysis. The spectral method is applied for the time evolution.
Abstract: A rigorous two-dimensional model is developed for simulating the operation of a less-investigated type steam reformer having a considerably lower operating Reynolds number, higher tube diameter, and non-availability of extra steam in the feed compared with conventional steam reformers. Simulation results show that reasonable predictions can only be achieved when certain correlations for wall to fluid heat transfer equations are applied. Due to severe operating conditions, in all cases, strong radial temperature gradients inside the reformer tubes have been found. Furthermore, the results show how a certain catalyst loading profile will affect the operation of the reformer.
Abstract: Two-dimensional (2D) bar codes were designed to
carry significantly more data with higher information density and
robustness than its 1D counterpart. Thanks to the popular
combination of cameras and mobile phones, it will naturally bring
great commercial value to use the camera phone for 2D bar code
reading. This paper addresses the problem of specific 2D bar code
design for mobile phones and introduces a low-level encoding
method of matrix codes. At the same time, we propose an efficient
scheme for 2D bar codes decoding, of which the effort is put on
solutions of the difficulties introduced by low image quality that is
very common in bar code images taken by a phone camera.
Abstract: Semiconductor detector arrays are widely used in
high-temperature plasma diagnostics. They have a fast response,
which allows observation of many processes and instabilities in
tokamaks. In this paper, there are reviewed several diagnostics based
on semiconductor arrays as cameras, AXUV photodiodes (referred
often as fast “bolometers") and detectors of both soft X-rays and
visible light installed on the COMPASS tokamak recently. Fresh
results from both spring and summer campaigns in 2012 are
introduced. Examples of the utilization of the detectors are shown on
the plasma shape determination, fast calculation of the radiation
center, two-dimensional plasma radiation tomography in different
spectral ranges, observation of impurity inflow, and also on
investigation of MHD activity in the COMPASS tokamak discharges.
Abstract: A conjugate heat transfer for steady two-dimensional
mixed convection with magnetic hydrodynamic (MHD) flow of an
incompressible quiescent fluid over an unsteady thermal forming
stretching sheet has been studied. A parameter, M, which is used to
represent the dominance of the magnetic effect has been presented in
governing equations. The similar transformation and an implicit
finite-difference method have been used to analyze the present
problem. The numerical solutions of the flow velocity distributions,
temperature profiles, the wall unknown values of f''(0) and '(θ (0) for
calculating the heat transfer of the similar boundary-layer flow are
carried out as functions of the unsteadiness parameter (S), the Prandtl
number (Pr), the space-dependent parameter (A) and
temperature-dependent parameter (B) for heat source/sink and the
magnetic parameter (M). The effects of these parameters have also
discussed. At the results, it will produce greater heat transfer effect
with a larger Pr and M, S, A, B will reduce heat transfer effects. At
last, conjugate heat transfer for the free convection with a larger G has
a good heat transfer effect better than a smaller G=0.