Abstract: Our aim in this piece of work is to demonstrate the
power of the Laplace Adomian decomposition method (LADM) in
approximating the solutions of nonlinear differential equations
governing the two-dimensional viscous flow induced by a shrinking
sheet.
Abstract: The comparisons of two typical fluidic thrust vectoring exhaust nozzles including two-dimensional(2-D) nozzle and axisymmetric nozzle on aerodynamic characteristics was presented by numerical simulation. The results show: the thrust vector angles increased with the increasing secondary flow but decreased with the nozzle pressure ratio (NPR) increasing. With the same secondary flow and NPR, the thrust vector angles of 2-D nozzle were higher than the axisymmetric nozzle-s. So with the lower NPR and more secondary weight flow, the much higher thrust vector angle was caused by 2-D fluidic nozzle. And with the higher NPR and less secondary weight flow, there was not much difference in angular dimension between two nozzles.
Abstract: The Spalart and Allmaras turbulence model has been
implemented in a numerical code to study the compressible turbulent
flows, which the system of governing equations is solved with a
finite volume approach using a structured grid. The AUSM+ scheme
is used to calculate the inviscid fluxes. Different benchmark
problems have been computed to validate the implementation and
numerical results are shown. A special Attention is paid to wall jet
applications. In this study, the jet is submitted to various wall
boundary conditions (adiabatic or uniform heat flux) in forced
convection regime and both two-dimensional and axisymmetric wall
jets are considered. The comparison between the numerical results
and experimental data has given the validity of this turbulence model
to study the turbulent wall jets especially in engineering applications.
Abstract: The seismic response of steel shear wall system considering nonlinearity effects using finite element method is investigated in this paper. The non-linear finite element analysis has potential as usable and reliable means for analyzing of civil structures with the availability of computer technology. In this research the large displacements and materially nonlinear behavior of shear wall is presented with developing of finite element code. A numerical model based on the finite element method for the seismic analysis of shear wall is presented with developing of finite element code in this research. To develop the finite element code, the standard Galerkin weighted residual formulation is used. Two-dimensional plane stress model and total Lagrangian formulation was carried out to present the shear wall response and the Newton-Raphson method is applied for the solution of nonlinear transient equations. The presented model in this paper can be developed for analysis of civil engineering structures with different material behavior and complicated geometry.
Abstract: In this paper, a generalized self-consistent scheme, or “three phase model", is used to set up a micro-mechanics model for rough surface contact with randomly distributed asperities. The dimensionless average real pressure p is obtained as function of the ratio of the real contact area to the apparent contact area, 0 A / A r . Both elastic and plastic materials are considered, and the influence of the plasticity of material on p is discussed. Both two-dimensional and three-dimensional rough surface contact problems are considered.
Abstract: Planar systems of electrodes arranged on both sides of dielectric piezoelectric layer are applied in numerous transducers. They are capable of electronic beam-steering of generated wave both in azimuth and elevation. The wave-beam control is achieved by addressable driving of two-dimensional transducer through proper voltage supply of electrodes on opposite surfaces of the layer. In this paper a semi-analytical method of analysis of the considered transducer is proposed, which is a generalization of the well-known BIS-expansion method. It was earlier exploited with great success in the theory of interdigital transducers of surface acoustic waves, theory of elastic wave scattering by cracks and certain advanced electrostatic problems. The corresponding nontrivial electrostatic problem is formulated and solved numerically.
Abstract: The background estimation approach using a small
window median filter is presented on the bases of analyzing IR point
target, noise and clutter model. After simplifying the two-dimensional
filter, a simple method of adopting one-dimensional median filter is
illustrated to make estimations of background according to the
characteristics of IR scanning system. The adaptive threshold is used
to segment canceled image in the background. Experimental results
show that the algorithm achieved good performance and satisfy the
requirement of big size image-s real-time processing.
Abstract: This paper objects to extend Jon Kleinberg-s research. He introduced the structure of small-world in a grid and shows with a greedy algorithm using only local information able to find route between source and target in delivery time O(log2n). His fundamental model for distributed system uses a two-dimensional grid with longrange random links added between any two node u and v with a probability proportional to distance d(u,v)-2. We propose with an additional information of the long link nearby, we can find the shorter path. We apply the ant colony system as a messenger distributed their pheromone, the long-link details, in surrounding area. The subsequence forwarding decision has more option to move to, select among local neighbors or send to node has long link closer to its target. Our experiment results sustain our approach, the average routing time by Color Pheromone faster than greedy method.
Abstract: The disaster from functional gastrointestinal disorders has detrimental impact on the quality of life of the effected population and imposes a tremendous social and economic burden. There are, however, rare diagnostic methods for the functional gastrointestinal disorders. Our research group identified recently that the gastrointestinal tract well in the patients with the functional gastrointestinal disorders becomes more rigid than healthy people when palpating the abdominal regions overlaying the gastrointestinal tract. Objective of current study is, therefore, identify feasibility of a diagnostic system for the functional gastrointestinal disorders based on ultrasound technique, which can quantify the characteristics above. Two-dimensional finite difference (FD) models (one normal and two rigid model) were developed to analyze the reflective characteristic (displacement) on each soft-tissue layer responded after application of ultrasound signals. The FD analysis was then based on elastic ultrasound theory. Validation of the model was performed via comparison of the characteristic of the ultrasonic responses predicted by FD analysis with that determined from the actual specimens for the normal and rigid conditions. Based on the results from FD analysis, ultrasound system for diagnosis of the functional gastrointestinal disorders was developed and clinically tested via application of it to 40 human subjects with/without functional gastrointestinal disorders who were assigned to Normal and Patient Groups. The FD models were favorably validated. The results from FD analysis showed that the maximum displacement amplitude in the rigid models (0.12 and 0.16) at the interface between the fat and muscle layers was explicitly less than that in the normal model (0.29). The results from actual specimens showed that the maximum amplitude of the ultrasonic reflective signal in the rigid models (0.2±0.1Vp-p) at the interface between the fat and muscle layers was explicitly higher than that in the normal model (0.1±0.2 Vp-p). Clinical tests using our customized ultrasound system showed that the maximum amplitudes of the ultrasonic reflective signals near to the gastrointestinal tract well for the patient group (2.6±0.3 Vp-p) were generally higher than those in normal group (0.1±0.2 Vp-p). Here, maximum reflective signals was appeared at 20mm depth approximately from abdominal skin for all human subjects, corresponding to the location of the boundary layer close to gastrointestinal tract well. These findings suggest that our customized ultrasound system using the ultrasonic reflective signal may be helpful to the diagnosis of the functional gastrointestinal disorders.
Abstract: In this paper, the two-dimensional reversed stagnationpoint
flow is solved by means of an anlytic approach. There are
similarity solutions in case the similarity equation and the boundary
condition are modified. Finite analytic method are applied to obtain
the similarity velocity function.
Abstract: The results of an experimental study of the process of
convective and boiling heat transfer in the vessel with stirrer for
smooth and rough ring-shaped pipes are presented. It is established
that creation of two-dimensional artificial roughness on the heated
surface causes the essential (~100%) intensification of convective
heat transfer. In case of boiling the influence of roughness appears on
the initial stage of boiling and in case of fully developed nucleate
boiling there was no intensification of heat transfer. The similitude
equation for calculating convective heat transfer coefficient, which
generalizes well experimental data both for the smooth and the rough
surfaces is proposed.
Abstract: Large full frequency band gaps of surface and bulk
acoustic waves in two-dimensional phononic band structures with
hollow cylinders are addressed in this paper. It is well-known that
absolute frequency band gaps are difficultly obtained in a band
structure consisted of low-acoustic-impedance cylinders in
high-acoustic-impedance host materials such as PMMA/Ni band
structures. Phononic band structures with hollow cylinders are
analyzed and discussed to obtain large full frequency band gaps not
only for bulk modes but also for surface modes. The tendency of
absolute frequency band gaps of surface and bulk acoustic waves is
also addressed by changing the inner radius of hollow cylinders in this
paper. The technique and this kind of band structure are useful for
tuning the frequency band gaps and the design of acoustic waveguides.
Abstract: We study bifurcation structure of the zonal jet flow the
streamfunction of which is expressed by a single spherical harmonics
on a rotating sphere. In the non-rotating case, we find that a steady
traveling wave solution arises from the zonal jet flow through Hopf
bifurcation. As the Reynolds number increases, several traveling
solutions arise only through the pitchfork bifurcations and at high
Reynolds number the bifurcating solutions become Hopf unstable. In
the rotating case, on the other hand, under the stabilizing effect of
rotation, as the absolute value of rotation rate increases, the number
of the bifurcating solutions arising from the zonal jet flow decreases
monotonically. We also carry out time integration to study unsteady
solutions at high Reynolds number and find that in the non-rotating
case the unsteady solutions are chaotic, while not in the rotating cases
calculated. This result reflects the general tendency that the rotation
stabilizes nonlinear solutions of Navier-Stokes equations.
Abstract: Equal Channel Angular Pressing (ECAP) is currently
being widely investigated because of its potential to produce ultrafine
grained microstructures in metals and alloys. A sound
knowledge of the plastic deformation and strain distribution is
necessary for understanding the relationships between strain
inhomogeneity and die geometry. Considerable research has been
reported on finite element analysis of this process, assuming threedimensional
plane strain condition. However, the two-dimensional
models are not suitable due to the geometry of the dies, especially in
cylindrical ones. In the present work, three-dimensional simulation of
ECAP process was carried out for six outer corner radii (sharp to 10
mm in steps of 2 mm), with channel angle 105¶Çü▒, for strain hardening
aluminium alloy (AA 6101) using ABAQUS/Standard software.
Strain inhomogeneity is presented and discussed for all cases. Pattern
of strain variation along selected radial lines in the body of the workpiece
is presented. It is found from the results that the outer corner
has a significant influence on the strain distribution in the body of
work-piece. Based on inhomogeneity and average strain criteria,
there is an optimum outer corner radius.
Abstract: In this work, the primary compressive strength
components of human femur trabecular bone are qualitatively
assessed using image processing and wavelet analysis. The Primary
Compressive (PC) component in planar radiographic femur trabecular
images (N=50) is delineated by semi-automatic image processing
procedure. Auto threshold binarization algorithm is employed to
recognize the presence of mineralization in the digitized images. The
qualitative parameters such as apparent mineralization and total area
associated with the PC region are derived for normal and abnormal
images.The two-dimensional discrete wavelet transforms are utilized
to obtain appropriate features that quantify texture changes in medical
images .The normal and abnormal samples of the human femur are
comprehensively analyzed using Harr wavelet.The six statistical
parameters such as mean, median, mode, standard deviation, mean
absolute deviation and median absolute deviation are derived at level
4 decomposition for both approximation and horizontal wavelet
coefficients. The correlation coefficient of various wavelet derived
parameters with normal and abnormal for both approximated and
horizontal coefficients are estimated. It is seen that in almost all cases
the abnormal show higher degree of correlation than normals. Further
the parameters derived from approximation coefficient show more
correlation than those derived from the horizontal coefficients. The
parameters mean and median computed at the output of level 4 Harr
wavelet channel was found to be a useful predictor to delineate the
normal and the abnormal groups.
Abstract: Multiport diffusers are the effective engineering
devices installed at the modern marine outfalls for the steady
discharge of effluent streams from the coastal plants, such as
municipal sewage treatment, thermal power generation and seawater
desalination. A mathematical model using a two-dimensional
advection-diffusion equation based on a flat seabed and incorporating
the effect of a coastal tidal current is developed to calculate the
compounded concentration following discharges of desalination
brine from a sea outfall with multiport diffusers. The analytical
solutions are computed graphically to illustrate the merging of
multiple brine plumes in shallow coastal waters, and further
approximation will be made to the maximum shoreline's
concentration to formulate dilution of a multiport diffuser discharge.
Abstract: Simulation of the flow and sedimentation process in
the reservoir dams can be made by two methods of physical and mathematical modeling. The study area was within a region which
ranged from the Jelogir hydrometric station to the Karkheh reservoir
dam aimed at investigating the effects of stream tubes on the
GSTARS-3 model behavior. The methodologies was to run the model based on 5 stream tubes in order to observe the influence of
each scenario on longitudinal profiles, cross-section, flow velocity and bed load sediment size. Results further suggest that the use of
two stream tubes or more which result in the semi-two-dimensional
model will yield relatively closer results to the observational data
than a singular stream tube modeling. Moreover, the results of
modeling with three stream tubes shown to yield a relatively close
results with the observational data. The overall conclusion of the paper is with applying various stream tubes; it would be possible to yield a significant influence on the modeling behavior Vis-a Vis the bed load sediment size.
Abstract: Wavelets have provided the researchers with
significant positive results, by entering the texture defect detection domain. The weak point of wavelets is that they are one-dimensional
by nature so they are not efficient enough to describe and analyze two-dimensional functions. In this paper we present a new method to
detect the defect of texture images by using curvelet transform.
Simulation results of the proposed method on a set of standard
texture images confirm its correctness. Comparing the obtained results indicates the ability of curvelet transform in describing
discontinuity in two-dimensional functions compared to wavelet
transform
Abstract: In this paper, a two-dimensional mathematical model is developed for estimating the extent of inland inundation due to Indonesian tsunami of 2004 along the coastal belts of Peninsular Malaysia and Thailand. The model consists of the shallow water equations together with open and coastal boundary conditions. In order to route the water wave towards the land, the coastal boundary is treated as a time dependent moving boundary. For computation of tsunami inundation, the initial tsunami wave is generated in the deep ocean with the strength of the Indonesian tsunami of 2004. Several numerical experiments are carried out by changing the slope of the beach to examine the extent of inundation with slope. The simulated inundation is found to decrease with the increase of the slope of the orography. Correlation between inundation / recession and run-up are found to be directly proportional to each other.
Abstract: Wall-surface jet induced by the dielectric barrier
discharge (DBD) has been proposed as an actuator for active flow
control in aerodynamic applications. Discharge plasma evolution of
the DBD plasma actuator was simulated based on a simple fluid model,
in which the electron, one type of positive ion and negative ion were
taken into account. Two-dimensional simulation was conducted, and
the results are in agreement with the insights obtained from
experimental studies. The simulation results indicate that the discharge
mode changes depending on applied voltage slope; when the applied
voltage is positive-going with high applied voltage slope, the
corona-type discharge mode turns into the streamer-type discharge
mode and the threshold voltage slope is around 300 kV/ms in this
simulation. The characteristics of the electrohydrodynamic (EHD)
force, which is the source of the wall-surface jet, also change
depending on the discharge mode; the tentative peak value of the EHD
force during the positive-going voltage phase is saturated by the
periodical formation of the streamer-type discharge.