Abstract: In this paper we report the technique of optical
induction of 2 and 3-dimensional (2D and 3D) photonic lattices in
photorefractive materials based on diffraction grating self replication
-Talbot effect. 1D and 2D different rotational symmery diffraction
masks with the periods of few tens micrometers and 532 nm cw laser
beam were used in the experiments to form an intensity modulated
light beam profile. A few hundred micrometric scale replications of
mask generated intensity structures along the beam propagation axis
were observed. Up to 20 high contrast replications were detected for
1D annular mask with 30
Abstract: In this work, stationary hot-wire measurements are
carried out to investigate the characteristics of a round free jet in its
potential core region (0 ≤ x/d ≤ 10). Measurements are carried out on
an incompressible round jet for a range of Reynolds numbers from
4000 to 8000, calculated based on the jet exit mean velocity and the
nozzle diameter. The effect of flow velocity on the development
characteristics of the jet in the core region is analyzed. Timeaveraged
statistics, spectra of velocity and its higher order moments
are presented and explained.
Abstract: A portable sensor for the analysis of phosphate in
aqueous samples has been developed. The sensor incorporates
microfluidic technology, colorimetric detection, and wireless
communications into a compact and rugged portable device. The
detection method used is the molybdenum yellow method, in which a
phosphate-containing sample is mixed with a reagent containing
ammonium metavanadate and ammonium molybdate in an acidic
medium. A yellow-coloured compound is generated and the
absorption of this compound is measured using a light emitting diode
(LED) light source and a photodiode detector. The absorption is
directly proportional to the phosphate concentration in the original
sample. In this paper we describe the application of this phosphate
sensor to the analysis of wastewater at a municipal wastewater
treatment plant in Co. Kildare, Ireland.
Abstract: This paper presents the results of preliminary
assessment of water quality along the coastal areas in the vicinity of
Left Bank Outfall Drainage (LBOD) and Tidal Link Drain (TLD) in
Sindh province after the cyclone 2A occurred in 1999. The water
samples were collected from various RDs of Tidal Link Drain and
lakes during September 2001 to April 2002 and were analysed for
salinity, nitrite, phosphate, ammonia, silicate and suspended material
in water. The results of the study showed considerable variations in
water quality depending upon the location along the coast in the
vicinity of LBOD and RDs. The salinity ranged between 4.39–65.25
ppt in Tidal Link Drain samples whereas 2.4–38.05 ppt in samples
collected from lakes. The values of suspended material at various
RDs of Tidal Link Drain ranged between 56.6–2134 ppm and at the
lakes between 68–297 ppm. The data of continuous monitoring at
RD–93 showed the range of PO4 (8.6–25.2 μg/l), SiO3 (554.96–1462
μg/l), NO2 (0.557.2–25.2 μg/l) and NH3 (9.38–23.62 μg/l). The
concentration of nutrients in water samples collected from different
RDs was found in the range of PO4 (10.85 to 11.47 μg/l), SiO3 (1624
to 2635.08 μg/l), NO2 (20.38 to 44.8 μg/l) and NH3 (24.08 to 26.6
μg/l). Sindh coastal areas which situated at the north-western
boundary the Arabian Sea are highly vulnerable to flood damages
due to flash floods during SW monsoon or impact of sea level rise
and storm surges coupled with cyclones passing through Arabian Sea
along Pakistan coast. It is hoped that the obtained data in this study
would act as a database for future investigations and monitoring of
LBOD and Tidal Link Drain coastal waters.
Abstract: In this paper, we give an overview of an online elearning
tool which has been developed for kids aged from nine to
eleven years old in Mauritius for the self-study of Mathematics in
order to prepare them for the CPE examination. The software does
not intend to render obsolete the existing pedagogical approaches.
Nowadays, the teaching-learning process is mainly focused towards
the class-room model. Moreover, most of the e-learning platforms
that exist are simply static ways of delivering resources using the
internet. There is nearly no interaction between the learner and the
tool. Our application will enable students to practice exercises online
and also work out sample examination papers. Another interesting
feature is that the kid will not have to wait for someone to correct the
work as the correction will be done online and on the spot. Additional
feedback is also provided for some exercises.
Abstract: This paper presents the influence of preloading on a)
the contact tractions, b) slip levels and c) stresses at the dovetail
blade-disc interface of an aero-engine through a three-dimensional
(3D) finite element (FE) modeling and analysis. The preloading is
applied by an interference fit at the dovetail interface and the bulk
loading is applied through the rotational speed of rotor. Preloading at
the dovetail interface reduces the peak contact pressure developed
due to bulk loading up to 35%, and reduces the peak contact pressure
and stress difference between top and bottom contact edges.
Increasing the level of preloading reduces the cyclic stress amplitude
at the interface up to certain values of preload and as a consequence,
an improvement in fatigue life could be expected. Fretting damage,
due to vibration and wind milling effect during engine ground
condition, can be minimized by preloading the dovetail interface.
Abstract: Due to the high increase in and demand for a wide assortment of applications that require low-cost, high-efficiency, and compact systems, RF power amplifiers are considered the most critical design blocks and power consuming components in wireless communication, TV transmission, radar, and RF heating. Therefore, much research has been carried out in order to improve the performance of power amplifiers. Classes-A, B, C, D, E and F are the main techniques for realizing power amplifiers.
An implementation of high efficiency class-F power amplifier with Gallium Nitride (GaN) High Electron Mobility Transistor (HEMT) was realized in this paper. The simulation and optimization of the class-F power amplifier circuit model was undertaken using Agilent’s Advanced Design system (ADS). The circuit was designed using lumped elements.
Abstract: Composite of Celatom-ZeoliteY (Cel-ZY) was used to
remove cobalt ion from an aqueous solution using batch mode.
ZeoliteY has successfully superimposed on Celatom FW-14 surface
using hydrothermal treatment .The product was synthesized as a
novel of hierarchical porous material. It was observed from the
results that Cel-ZY has higher ability to remove cobalt ions than the
pure ZeoliteY powder (PZY) synthesized under the same conditions.
Several parameters were studied in this project to investigate the
effect of removal cobalt ion such as pH and initial cobalt
concentration. It was clearly observed that the uptake of cobalt ions
was affected with increase these parameters. The results proved that
the product can be used effectively to remove Co2+ ions from
wastewater as an environmentally friendly alternative.
Abstract: MOC (method of cell) is a new method of investigating
wave propagating in material with periodic microstructure, and can
reflect the effect of microstructure. Wave propagation in periodically
laminated medium consisting of linearly elastic layers can be treated
as a special application of this method. In this paper, it was used to
simulate the dynamic response of carbon-phenolic to impulsive
loading under certain boundary conditions. From the comparison
between the results obtained from this method and the exact results
based on propagator matrix theory, excellent agreement is achieved.
Conclusion can be made that the oscillation periodicity is decided by
the thickness of sub-cells. In the end, the NHDMOC method, which
permits studying stress wave propagation with one dimensional strain,
was applied to study the one-dimensional stress wave propagation. In
this paper, the ZWT nonlinear visco-elastic constitutive relationship
with 7 parameters, NHDMOC, and corresponding equations were
deduced. The equations were verified, comparing the elastic stress
wave propagation in SHPB with, respectively, the elastic and the
visco-elastic bar. Finally the dispersion and attenuation of stress wave
in SHPB with visco-elastic bar was studied.
Abstract: In this study, the sorption of Malachite green (MG) on Hydrilla verticillata biomass, a submerged aquatic plant, was investigated in a batch system. The effects of operating parameters such as temperature, adsorbent dosage, contact time, adsorbent size, and agitation speed on the sorption of Malachite green were analyzed using response surface methodology (RSM). The proposed quadratic model for central composite design (CCD) fitted very well to the experimental data that it could be used to navigate the design space according to ANOVA results. The optimum sorption conditions were determined as temperature - 43.5oC, adsorbent dosage - 0.26g, contact time - 200min, adsorbent size - 0.205mm (65mesh), and agitation speed - 230rpm. The Langmuir and Freundlich isotherm models were applied to the equilibrium data. The maximum monolayer coverage capacity of Hydrilla verticillata biomass for MG was found to be 91.97 mg/g at an initial pH 8.0 indicating that the optimum sorption initial pH. The external and intra particle diffusion models were also applied to sorption data of Hydrilla verticillata biomass with MG, and it was found that both the external diffusion as well as intra particle diffusion contributes to the actual sorption process. The pseudo-second order kinetic model described the MG sorption process with a good fitting.
Abstract: The aim of this study was to synthesize the single
walled carbon nanotubes (SWCNTs) and determine their hydrogen
storage capacities. SWCNTs were firstly synthesized by chemical
vapor deposition (CVD) of acetylene (C2H2) on a magnesium oxide
(MgO) powder impregnated with an iron nitrate (Fe(NO3)3·9H2O)
solution. The synthesis parameters were selected as: the synthesis
temperature of 800°C, the iron content in the precursor of 5% and the
synthesis time of 30 min. Purification process of SWCNTs was
fulfilled by microwave digestion at three different temperatures (120,
150 and 200 °C), three different acid concentrations (0.5, 1 and 1.5
M) and for three different time intervals (15, 30 and 60 min). Nitric
acid (HNO3) was used in the removal of the metal catalysts. The
hydrogen storage capacities of the purified materials were measured
using volumetric method at the liquid nitrogen temperature and gas
pressure up to 100 bar. The effects of the purification conditions such
as temperature, time and acid concentration on hydrogen adsorption
were investigated.
Abstract: Snow cover is an important phenomenon in
hydrology, hence modeling the snow accumulation and melting is an
important issue in places where snowmelt significantly contributes to
runoff and has significant effect on water balance. The physics-based
models are invariably distributed, with the basin disaggregated into
zones or grid cells. Satellites images provide valuable data to verify
the accuracy of spatially distributed model outputs. In this study a
spatially distributed physically based model (WetSpa) was applied to
predict snow cover and melting in the Latyan dam watershed in Iran.
Snowmelt is simulated based on an energy balance approach. The
model is applied and calibrated with one year of observed daily
precipitation, air temperature, windspeed, and daily potential
evaporation. The predicted snow-covered area is compared with
remotely sensed images (MODIS). The results show that simulated
snow cover area SCA has a good agreement with satellite image
snow cover area SCA from MODIS images. The model performance
is also tested by statistical and graphical comparison of simulated and
measured discharges entering the Latyan dam reservoir.
Abstract: This paper describes an experimental, theoretical
model and numerical study of concentrated vortex flow past a sphere
in a hydraulic check valve. The phenomenon of the rotation of the
ball around the axis of the device through which liquid flows has
been found. That is, due to the rotation of the sphere in the check
valve vibration is caused. We observe the rotation of the sphere
around the longitudinal axis of the check valve. This rotation is
induced by a vortex shedding from the sphere. We will discuss
computational simulation and experimental investigations of this
strong sphere rotation. The frequency of the sphere vibration and
interaction with the check valve wall has been measured as a function
of the wide range Reynolds Number. The validity of the
computational simulation and of the assumptions on which it is based
has been proved experimentally. This study demonstrates the
possibility to control the vibrations in a hydraulic system and proves
to be very effective suppression of the self-excited vibration.
Abstract: We developed a method based on quasi-molecular
modelling to simulate the fall of water drops on horizontally smooth
and rough surfaces. Each quasi-molecule was a group of particles
that interacted in a fashion entirely analogous to classical Newtonian
molecular interactions. When a falling water droplet was simulated at
low impact velocity on both smooth and rough surfaces, the droplets
moved periodically (i.e. the droplets moved up and down for a
certain period, finally they stopped moving and reached a steady
state), spreading and recoiling without splash or break-up. Spreading
rates of falling water droplets increased rapidly as time increased
until the spreading rate reached its steady state at time t ~ 0.25 s for
rough surface and t ~ 0.40 s for smooth surface. The droplet height
above both surfaces decreased as time increased, remained constant
after the droplet diameter attained a maximum value and reached its
steady state at time t ~ 0.4 s. However, rough surface had higher
spreading rates of falling water droplets and lower height on the
surface than smooth one.
Abstract: Helical milling operations are used to generate or
enlarge boreholes by means of a milling tool. The bore diameter can be
adjusted through the diameter of the helical path. The kinematics of
helical milling on a three axis machine tool is analysed firstly. The
relationships between processing parameters, cutting tool geometry
characters with machined hole feature are formulated. The feed motion
of the cutting tool has been decomposed to plane circular feed and
axial linear motion. In this paper, the time varying cutting forces acted
on the side cutting edges and end cutting edges of the flat end cylinder
miller is analysed using a discrete method separately. These two
components then are combined to produce the cutting force model
considering the complicated interaction between the cutters and
workpiece. The time varying cutting force model describes the
instantaneous cutting force during processing. This model could be
used to predict cutting force, calculate statics deflection of cutter and
workpiece, and also could be the foundation of dynamics model and
predicting chatter limitation of the helical milling operations.
Abstract: Based on a long-term vegetation index dataset of NDVI and meteorological data from 68 meteorological stations in the Qinghai-Tibet plateau and their relations with major climate factors were analyzed. The results show the following: 1) The linear trends of temperature in the Qinghai-Tibet plateau indicate that the temperature in the plateau generally increased, but it rose faster in the last 20 years. 2) The most significant NDVI increase occurred in the eastern and southern plateau. However, the western and northern plateau demonstrate a decreasing trend. 3) There is a significant positive linear correlation between NDVI and temperature and a negative correlation between NDVI and mean wind speed. However, no significant statistical relationship was found between NDVI and relative humidity, precipitation or sunshine duration.4) The changes in NDVI for the plateau are driven by temperature-precipitation, but for the desert and forest areas, the relation changes to precipitation-temperature-wind velocity and wind velocity-temperature-precipitation.
Abstract: The rate of production of main products of the Fischer-Tropsch reactions over Fe/HZSM5 bifunctional catalyst in a fixed bed reactor is investigated at a broad range of temperature, pressure, space velocity, H2/CO feed molar ratio and CO2, CH4 and water flow rates. Model discrimination and parameter estimation were performed according to the integral method of kinetic analysis. Due to lack of mechanism development for Fisher – Tropsch Synthesis on bifunctional catalysts, 26 different models were tested and the best model is selected. Comprehensive one and two dimensional heterogeneous reactor models are developed to simulate the performance of fixed-bed Fischer – Tropsch reactors. To reduce computational time for optimization purposes, an Artificial Feed Forward Neural Network (AFFNN) has been used to describe intra particle mass and heat transfer diffusion in the catalyst pellet. It is seen that products' reaction rates have direct relation with H2 partial pressure and reverse relation with CO partial pressure. The results show that the hybrid model has good agreement with rigorous mechanistic model, favoring that the hybrid model is about 25-30 times faster.
Abstract: A self-association model has been used to understand
the concentration dependence of free energy of mixing (GM), heat of
mixing (HM), entropy of mixing (SM), activity (a) and microscopic
structures, such as concentration fluctuation in long wavelength limit
(Scc(0)) and Warren-Cowley short range order parameter ( 1
α )for Cu-
Tl molten alloys at 1573K. A comparative study of surface tension of
the alloys in the liquid state at that temperature has also been carried
out theoretically as function of composition in the light of Butler-s
model, Prasad-s model and quasi-chemical approach. Most of the
computed thermodynamic properties have been found in agreement
with the experimental values. The analysis reveals that the Cu-Tl
molten alloys at 1573K represent a segregating system at all
concentrations with moderate interaction. Surface tensions computed
from different approaches have been found to be comparable to each
other showing increment with the composition of copper.
Abstract: Computer-based decision support (CDSS) systems can
deliver real patient care and increase chances of long-term survival in
areas of chronic disease management prone to poor control. One such
CDSS, for the management of warfarin, is described in this paper and
the outcomes shown. Data is derived from the running system and
show a performance consistently around 20% better than the
applicable guidelines.
Abstract: In this study, the conversion of n-pentane to aromatics is investigated on HZSM-5 zeolites modified by Ga ion-exchange and silylation using tetraethyl orthosilicate (TEOS) via chemical liquid deposition (CLD). The effect of SiO2/Al2O3 ratios of HZSM-5 was also studied. Parameters in preparing catalysts i.e. TEOS loading and cycles of deposition were varied to obtain the optimal condition for enhancing p-xylene selectivity. The highest p-xylene selectivity 99.7% was achieved when the amount of TEOS was 20 vol.%.The catalysts were characterized by TPD, TPO, XRF, and BET. Results show that the conversion of n-pentane was influenced remarkably by the SiO2/Al2O3 ratios of HZSM-5. The highest p-xylene selectivity 99.7% was achieved when the amount of TEOS was 20 vol.%. And cycles of deposition greatly improves HZSM-5 shape-selectivity.