Abstract: This paper presents small signal stability study carried
over the 140-Bus, 31-Machine, 5-Area MEPE system and validated
on free and open source software: PSAT. Well-established linearalgebra
analysis, eigenvalue analysis, is employed to determine the
small signal dynamic behavior of test system. The aspects of local
and interarea oscillations which may affect the operation and
behavior of power system are analyzed. Eigenvalue analysis is carried
out to investigate the small signal behavior of test system and the
participation factors have been determined to identify the
participation of the states in the variation of different mode shapes.
Also, the variations in oscillatory modes are presented to observe the
damping performance of the test system.
Abstract: Random epistemologies and hash tables have garnered
minimal interest from both security experts and experts in the last
several years. In fact, few information theorists would disagree with
the evaluation of expert systems. In our research, we discover how
flip-flop gates can be applied to the study of superpages. Though
such a hypothesis at first glance seems perverse, it is derived from
known results.
Abstract: Elastomeric dielectric material has recently become a
new alternative for actuator technology. The characteristics of
dielectric elastomers placed between two electrodes to withstand
large strain when electrodes are charged has attracted the attention of
many researcher to study this material for actuator technology. Thus,
in the past few years Danfoss Ventures A/S has established their own
dielectric electro-active polymer (DEAP), which was called
PolyPower.
The main objective of this work was to investigate the dynamic
characteristics for vibration control of a PolyPower actuator folded in
‘pull’ configuration. A range of experiments was carried out on the
folded actuator including passive (without electrical load) and active
(with electrical load) testing. For both categories static and dynamic
testing have been done to determine the behavior of folded DEAP
actuator.
Voltage-Strain experiments show that the DEAP folded actuator is
a non-linear system. It is also shown that the voltage supplied has no
effect on the natural frequency. Finally, varying AC voltage with
different amplitude and frequency shows the parameters that
influence the performance of DEAP folded actuator. As a result, the
actuator performance dominated by the frequency dependence of the
elastic response and was less influenced by dielectric properties.
Abstract: Speech Segmentation is the measure of the change
point detection for partitioning an input speech signal into regions
each of which accords to only one speaker. In this paper, we apply
two features based on multi-scale product (MP) of the clean speech,
namely the spectral centroid of MP, and the zero crossings rate of
MP. We focus on multi-scale product analysis as an important tool
for segmentation extraction. The MP is based on making the product
of the speech wavelet transform coefficients (WTC). We have
estimated our method on the Keele database. The results show the
effectiveness of our method. It indicates that the two features can find
word boundaries, and extracted the segments of the clean speech.
Abstract: The distribution networks are often exposed to harmful
incidents which can halt the electricity supply of the customer. In this
context, we studied a real case of a critical zone of the Tunisian
network which is currently characterized by the dysfunction of its
plan of protection. In this paper, we were interested in the
harmonization of the protection plan settings in order to ensure a
perfect selectivity and a better continuity of service on the whole of
the network.
Abstract: A compact UWB planar antenna fed with a
microstrip-line is proposed. The new design consist of a rectangular
patch with symmetric l-shaped slots and fed by 50 Ω microstrip
transmission line and a reduced ground-plane which have a periodic
slots with an overall size of 47 mm x 20 mm. It is intended to be used
in wireless applications that cover the ultra-wideband (UWB)
frequency band. A wider impedance bandwidth of around 116.5%
(1.875 – 7.115 GHz) with stable radiation pattern is achieved. The
proposed antenna has excellent characteristics, low profile and costeffective
compared to existing UWB antennas. The UWB antenna is
designed and analyzed using CST Microwave Studio in transient
mode to verify antenna parameters improvements.
Abstract: The dielectric properties and ionic conductivity of
novel "ceramic state" polymer electrolytes for high capacity lithium
battery are characterized by Radio frequency and Microwave
methods in two broad frequency ranges from 50 Hz to 20 KHz and 4
GHz to 40 GHz. This innovative solid polymer electrolyte which is
highly ionic conductive (10-3 S/cm at room temperature) from -40oC
to +150oC can be used in any battery application. Such polymer
exhibits properties more like a ceramic rather than polymer. The
various applied measurement methods produced accurate dielectric
results for comprehensive analysis of electrochemical properties and
ion transportation mechanism of this newly invented polymer
electrolyte. Two techniques and instruments employing air gap
measurement by Capacitance Bridge and in-waveguide measurement
by vector network analyzer are applied to measure the complex
dielectric spectra. The complex dielectric spectra are used to
determine the complex alternating current electrical conductivity and
thus the ionic conductivity.
Abstract: The study of the electrical signals produced by neural
activities of human brain is called Electroencephalography. In this
paper, we propose an automatic and efficient EEG signal
classification approach. The proposed approach is used to classify the
EEG signal into two classes: epileptic seizure or not. In the proposed
approach, we start with extracting the features by applying Discrete
Wavelet Transform (DWT) in order to decompose the EEG signals
into sub-bands. These features, extracted from details and
approximation coefficients of DWT sub-bands, are used as input to
Principal Component Analysis (PCA). The classification is based on
reducing the feature dimension using PCA and deriving the supportvectors
using Support Vector Machine (SVM). The experimental are
performed on real and standard dataset. A very high level of
classification accuracy is obtained in the result of classification.
Abstract: Speech enhancement is a long standing problem with
numerous applications like teleconferencing, VoIP, hearing aids and
speech recognition. The motivation behind this research work is to
obtain a clean speech signal of higher quality by applying the optimal
noise cancellation technique. Real-time adaptive filtering algorithms
seem to be the best candidate among all categories of the speech
enhancement methods. In this paper, we propose a speech
enhancement method based on Recursive Least Squares (RLS)
adaptive filter of speech signals. Experiments were performed on
noisy data which was prepared by adding AWGN, Babble and Pink
noise to clean speech samples at -5dB, 0dB, 5dB and 10dB SNR
levels. We then compare the noise cancellation performance of
proposed RLS algorithm with existing NLMS algorithm in terms of
Mean Squared Error (MSE), Signal to Noise ratio (SNR) and SNR
Loss. Based on the performance evaluation, the proposed RLS
algorithm was found to be a better optimal noise cancellation
technique for speech signals.
Abstract: Iran has several potential for using renewable
energies, so use them could significantly contribute to energy supply.
The purpose of this paper is to identify the potential of the country
and select the appropriate DG technologies with consideration the
potential and primary energy resources in the regions. In this context,
hybrid energy systems proportionate with the potential of different
regions will be determined based on technical, economic, and
environmental aspect. In the following the proposed structure will be
optimized in terms of size and cost. DG technologies used in this
project include photovoltaic system, wind turbine, diesel generator
and battery bank. The HOMER software is applied for choosing the
appropriate structure and the optimization of system sizing. The
results have been analyzed in terms of technical and economic. The
performance and the cost of each project demonstrate the appropriate
structure of hybrid energy system in that region.
Abstract: In this paper, the improvement by deconvolution of
the depth resolution in Secondary Ion Mass Spectrometry (SIMS)
analysis is considered. Indeed, we have developed a new Tikhonov-
Miller deconvolution algorithm where a priori model of the solution
is included. This is a denoisy and pre-deconvoluted signal obtained
from: firstly, by the application of wavelet shrinkage algorithm,
secondly by the introduction of the obtained denoisy signal in an
iterative deconvolution algorithm. In particular, we have focused the
light on the effect of the iterations number on the evolution of the
deconvoluted signals. The SIMS profiles are multilayers of Boron in
Silicon matrix.
Abstract: The emerging Cognitive Radio is combo of both the
technologies i.e. Radio dynamics and software technology. It involve
wireless system with efficient coding, designing, and making them
artificial intelligent to take the decision according to the surrounding
environment and adopt themselves accordingly, so as to deliver the
best QoS. This is the breakthrough from fixed hardware and fixed
utilization of the spectrum. This software-defined approach of
research is centralized at user-definition and application driven
model, various software method are used for the optimization of the
wireless communication. This paper focused on the Spectrum
allocation technique using genetic algorithm GA to evolve radio,
represented by chromosomes. The chromosomes gene represents the
adjustable parameters in given radio and by using GA, evolving over
the generations, the optimized set of parameters are evolved, as per
the requirement of user and availability of the spectrum, in our
prototype the gene consist of 6 different parameters, and the best set
of parameters are evolved according to the application need and
availability of the spectrum holes and thus maintaining best QoS for
user, simultaneously maintaining licensed user rights. The analyzing
tool Matlab is used for the performance of the prototype.
Abstract: This paper presents modeling of an Alternating
Current (AC) Photovoltaic (PV) module using Matlab/Simulink. The
proposed AC-PV module model is simple, realistic, and application
oriented. The model is derived on module level as compared to cell
level directly from the information provided by the manufacturer data
sheet. DC-PV module, MPPT control, BC, VSI and LC filter, all
were treated as a single unit. The model accounts for changes in
variations of both irradiance and temperature. The AC-PV module
proposed model is simulated and the results are compared with the
datasheet projected numbers to validate model’s accuracy and
effectiveness. Implementation and results demonstrate simplicity and
accuracy, as well as reliability of the model.
Abstract: This study is used as a definition method to the value
and function in manufacturing sector. In concurrence of discussion
about present condition of modeling method, until now definition of
1D-CAE is ambiguity and not conceptual. Across all the physic fields,
those methods are defined with the formulation of differential
algebraic equation which only applied time derivation and simulation.
At the same time, we propose semi-acausal modeling concept and
differential algebraic equation method as a newly modeling method
which the efficiency has been verified through the comparison of
numerical analysis result between the semi-acausal modeling
calculation and FEM theory calculation.
Abstract: High Peak to Average Power Ratio (PAPR) of the
transmitted signal is a serious problem in multicarrier systems (MC),
such as Orthogonal Frequency Division Multiplexing (OFDM), or in
Multi-Carrier Code Division Multiple Access (MC-CDMA) systems,
due to large number of subcarriers. This effect is possible reduce with
some PAPR reduction techniques. Spreading sequences at the
presence of Saleh and Rapp models of high power amplifier (HPA)
have big influence on the behavior of system. In this paper we
investigate the bit-error-rate (BER) performance of MC-CDMA
systems. Basically we can see from simulations that the MC-CDMA
system with Iterative algorithm can be providing significantly better
results than the MC-CDMA system. The results of our analyses are
verified via simulation.
Abstract: This paper presents a novel fractal antenna structure
proposed for UWB (Ultra – Wideband) applications. The frequency
band 3.1-10.6GHz released by FCC (Federal Communication
Commission) as the commercial operation of UWB has been chosen
as frequency range for this antenna based on coplanar waveguide
(CPW) feed and circular shapes fulfilled according to fractal
geometry. The proposed antenna is validated and designed by using
an FR4 substrate with overall area of 34x43 mm2. The simulated
results performed by CST-Microwave Studio and compared by ADS
(Advanced Design System) show good matching input impedance
with return loss less than -10dB between 2.9 GHz and 11 GHz.
Abstract: Solenoid operated electromagnetic control valve
(ECV) playing an important role for car’s air conditioning control
system. ECV is used in external variable displacement swash plate
type compressor and controls the entire air conditioning system by
means of a pulse width modulation (PWM) input signal supplying
from an external source (controller). Complete form of ECV contains
number of internal features like valve body, core, valve guide,
plunger, guide pin, plunger spring, bellows etc. While designing the
ECV; dimensions of different internal items must meet the standard
requirements as it is quite challenging. In this research paper,
especially the dimensioning of ECV body and its three pressure ports
through which the air/refrigerant passes are considered. Here internal
leakage test analysis of ECV body is being carried out from its
discharge port (Pd) to crankcase port (Pc) when the guide valve is
placed inside it. The experiments have made both in ordinary and
digital system using different assumptions and thereafter compare the
results.
Abstract: In this work, we study the behavior of introducing
atomic size vacancy in a graphene nanoribbon superlattice. Our
investigations are based on the density functional theory (DFT) with
the Local Density Approximation in Atomistix Toolkit (ATK). We
show that, in addition to its shape, the position of vacancy has a
major impact on the electrical properties of a graphene nanoribbon
superlattice. We show that the band gap of an armchair graphene
nanoribbon may be tuned by introducing an appropriate periodic
pattern of vacancies. The band gap changes in a zig-zag manner
similar to the variation of band gap of a graphene nanoribbon by
changing its width.
Abstract: This paper presents a novel statistical description of
the counterpoise effective length due to lightning surges, where the
(impulse) effective length had been obtained by means of regressive
formulas applied to the transient simulation results. The effective
length is described in terms of a statistical distribution function, from
which median, mean, variance, and other parameters of interest could
be readily obtained. The influence of lightning current amplitude,
lightning front duration, and soil resistivity on the effective length has
been accounted for, assuming statistical nature of these parameters. A
method for determining the optimal counterpoise length, in terms of
the statistical impulse effective length, is also presented. It is based on
estimating the number of dangerous events associated with lightning
strikes. Proposed statistical description and the associated method
provide valuable information which could aid the design engineer in
optimising physical lengths of counterpoises in different grounding
arrangements and soil resistivity situations.
Abstract: The aim of this study was to design and simulate a
particular type of Asynchronous State Machine (ASM), namely a
‘traffic light controller’ (TLC), operated at a frequency of 0.5 Hz.
The design task involved two main stages: firstly, designing a 4-bit
binary counter using J-K flip flops as the timing signal and,
subsequently, attaining the digital logic by deploying ASM design
process. The TLC was designed such that it showed a sequence of
three different colours, i.e. red, yellow and green, corresponding to
set thresholds by deploying the least number of AND, OR and NOT
gates possible. The software Multisim was deployed to design such
circuit and simulate it for circuit troubleshooting in order for it to
display the output sequence of the three different colours on the
traffic light in the correct order. A clock signal, an asynchronous 4-
bit binary counter that was designed through the use of J-K flip flops
along with an ASM were used to complete this sequence, which was
programmed to be repeated indefinitely. Eventually, the circuit was
debugged and optimized, thus displaying the correct waveforms of
the three outputs through the logic analyser. However, hazards
occurred when the frequency was increased to 10 MHz. This was
attributed to delays in the feedback being too high.