Abstract: Multiple User Interference (MUI) considers the
primary problem in Optical Code-Division Multiple Access
(OCDMA), which resulting from the overlapping among the users. In
this article we aim to mitigate this problem by studying an
interference cancellation scheme called successive interference
cancellation (SIC) scheme. This scheme will be tested on two
different detection schemes, spectral amplitude coding (SAC) and
direct detection systems (DS), using partial modified prime (PMP) as
the signature codes. It was found that SIC scheme based on both SAC
and DS methods had a potential to suppress the intensity noise, that is
to say it can mitigate MUI noise. Furthermore, SIC/DS scheme
showed much lower bit error rate (BER) performance relative to
SIC/SAC scheme for different magnitude of effective power. Hence,
many more users can be supported by SIC/DS receiver system.
Abstract: Transparent nickel doped cobalt sulfide was fabricated
on a SnO2:F electrode and tested as an efficient electrocatalyst and as
an alternative to the expensive platinum counter electrode. In order to
investigate how this electrode could affect the electrical
characteristics of a dye-sensitized solar cell, we manufactured cells
with the same TiO2 photoanode sensitized with dye (N719) and
employing the same quasi-solid electrolyte, altering only the counter
electrode used. The cells were electrically and electrochemically
characterized and it was observed that the ones with the Ni doped
CoS2 outperformed the efficiency of the cells with the Pt counter
electrode (3.76% and 3.44% respectively). Particularly, the higher
efficiency of the cells with the Ni doped CoS2 counter electrode (CE)
is mainly because of the enhanced photocurrent density which is
attributed to the enhanced electrocatalytic ability of the CE and the
low charge transfer resistance at the CE/electrolyte interface.
Abstract: The lifetime of a wireless sensor network can be
effectively increased by using scheduling operations. Once the
sensors are randomly deployed, the task at hand is to find the largest
number of disjoint sets of sensors such that every sensor set provides
complete coverage of the target area. At any instant, only one of these
disjoint sets is switched on, while all other are switched off. This
paper proposes a heuristic search method to find the maximum
number of disjoint sets that completely cover the region. A
population of randomly initialized members is made to explore the
solution space. A set of heuristics has been applied to guide the
members to a possible solution in their neighborhood. The heuristics
escalate the convergence of the algorithm. The best solution explored
by the population is recorded and is continuously updated. The
proposed algorithm has been tested for applications which require
sensing of multiple target points, referred to as point coverage
applications. Results show that the proposed algorithm outclasses the
existing algorithms. It always finds the optimum solution, and that
too by making fewer number of fitness function evaluations than the
existing approaches.
Abstract: Nanotechnology has become the world attention in
various applications including the solar cells devices due to the
uniqueness and benefits of achieving low cost and better
performances of devices. Recently, thin film solar cells such as
Cadmium Telluride (CdTe), Copper-Indium-Gallium-diSelenide
(CIGS), Copper-Zinc-Tin-Sulphide (CZTS), and Dye-Sensitized
Solar Cells (DSSC) enhanced by nanotechnology have attracted
much attention. Thus, a compilation of nanotechnology devices
giving the progress in the solar cells has been presented. It is much
related to nanoparticles or nanocrystallines, carbon nanotubes, and
nanowires or nanorods structures.
Abstract: In the cooperative transmission scheme, both the
cellular system and broadcasting system are composed. Two cellular
base stations (CBSs) communicating with a user in the cell edge use
cooperative transmission scheme in the conventional scheme. In the
case that the distance between two CBSs and the user is distant, the
conventional scheme does not guarantee the quality of the
communication because the channel condition is bad. Therefore, if the
distance between CBSs and a user is distant, the performance of the
conventional scheme is decreased. Also, the bad channel condition has
bad effects on the performance. The proposed scheme uses two relays
to communicate well with CBSs when the channel condition between
CBSs and the user is poor. Using the relay in the high attenuation
environment can obtain both advantages of the high bit error rate
(BER) and throughput performance.
Abstract: In this paper, influence of harmonics on medium
voltage distribution system of Bogazici Electricity Distribution Inc.
(BEDAS) which takes place at Istanbul/Turkey is investigated. A ring
network consisting of residential loads is taken into account for this
study. Real system parameters and measurement results are used for
simulations. Also, probable working conditions of the system are
analyzed for 50%, 75%, and 100% loading of transformers with
similar harmonic contents. Results of the study are exhibited the
influence of nonlinear loads on %THDV, P.F. and technical losses of
the medium voltage distribution system.
Abstract: High Voltage Direct Current (HVDC) power
transmission is employed to move large amounts of electric power.
There are several possibilities to enhance the transient stability in a
power system. One adequate option is by using the high
controllability of the HVDC if HVDC is available in the system. This
paper presents a control technique for HVDC to enhance the transient
stability. The strategy controls the power through the HVDC to help
make the system more transient stable during disturbances. Loss of
synchronism is prevented by quickly producing sufficient
decelerating energy to counteract accelerating energy gained during.
In this study, the power flow in the HVDC link is modulated with the
addition of an auxiliary signal to the current reference of the rectifier
firing angle controller. This modulation control signal is derived from
speed deviation signal of the generator utilizing a PD controller; the
utilization of a PD controller is suitable because it has the property of
fast response. The effectiveness of the proposed controller is
demonstrated with a SMIB test system.
Abstract: This paper describes a novel sensor device, a pressure
pulse wave meter, which uses a bidirectional condenser microphone.
The microphone work as a microphone as well as a sensor with high
gain over a wide frequency range; they are also highly reliable and
economic. Currently aging is becoming a serious social issue in Japan causing
increased medical expenses in the country. Hence, it is important for
elderly citizens to check health condition at home, and to care the
health conditions through daily monitoring. Given this circumstances,
we developed a novel pressure pulse wave meter based on a
bidirectional condenser microphone: this device is used as a measuring
instrument of health conditions.
Abstract: This paper is focused on the reference current
calculation in the compensation mode of the active DC traction
substations. The so-called p-q theory of the instantaneous reactive
power is used as theoretical foundation. The compensation goal of
total compensation is taken into consideration for the operation under
both sinusoidal and nonsinusoidal voltage conditions, through the
two objectives of unity power factor and perfect harmonic
cancelation. Four blocks of reference current generation implement
the conceived algorithms and they are included in a specific Simulink
library, which is useful in a DSP dSPACE-based platform working
under Matlab/Simulink. The simulation results validate the
correctness of the implementation and fulfillment of the
compensation tasks.
Abstract: While choosing insulating oil, characteristic features
such as thermal cooling, endurance, efficiency and being
environment-friendly should be considered. Mineral oils are referred
as petroleum-based oil. In this study, vegetable oils investigated as an
alternative insulating liquid to mineral oil. Dissipation factor,
breakdown voltage, relative dielectric constant and resistivity
changes with the frequency and voltage of mineral, rapeseed and nut
oils were measured. Experimental studies were performed according
to ASTM D924 and IEC 60156 standards.
Abstract: In this paper, improved performance scheme for
joint transmission (JT) is proposed in downlink (DL) coordinated
multi-point (CoMP) in case of the constraint transmission power.
This scheme is that a serving transmission point (TP) requests the
JT to an inter-TP and it selects a precoding technique according
to the channel state information (CSI) from user equipment (UE).
The simulation results show that the bit error rate (BER) and the
throughput performances of the proposed scheme provide the high
spectral efficiency and the reliable data at the cell edge.
Abstract: The conventional Wi-Fi backscatter system can only
process one-to-one communication between the Wi-Fi reader and the
Wi-Fi tag. For improvement of throughput of the conventional system,
this paper proposes the multi-to-multi communication system. In the
proposed system, the interference by the multi-to-multi
communication is effectively cancelled by the orthogonal multiple
access based on the identification code of the tag. Although the
overhead is generated by the procedure for the multi-to-multi
communication, because the procedure is processed by the Wi-Fi
protocol, the overhead is insignificant for the entire communication
procedure. From the numerical results, it is confirmed that the
proposed system has nearly proportional increased throughput in
according to the number of the tag that simultaneously participates in
communication.
Abstract: Sampled-data controller is presented for solid oxide
fuel cell systems which is expressed by a sector bounded nonlinear
model. The proposed control law is obtained by solving a convex
problem satisfying several linear matrix inequalities. Simulation
results are given to show the effectiveness of the proposed design
method.
Abstract: An Acoustic Micro-Energy Harvester (AMEH) is
developed to convert wasted acoustical energy into useful electrical
energy. AMEH is mathematically modeled using Lumped Element
Modelling (LEM) and Euler-Bernoulli beam (EBB) modelling. An
experiment is designed to validate the mathematical model and assess
the feasibility of AMEH. Comparison of theoretical and experimental
data on critical parameter value such as Mm, Cms, dm and Ceb showed
the variances are within 1% to 6%, which is reasonably acceptable.
Then, AMEH undergoes bandwidth tuning for performance
optimization. The AMEH successfully produces 0.9V/(m/s^2) and
1.79μW/(m^2/s^4) at 60Hz and 400kΩ resistive load which only
show variances about 7% compared to theoretical data. At 1g and
60Hz resonance frequency, the averaged power output is about
2.2mW which fulfilled a range of wireless sensors and
communication peripherals power requirements. Finally, the design
for AMEH is assessed, validated and deemed as a feasible design.
Abstract: This paper presents Carrier Sense Multiple Access
(CSMA) communication models based on SoC design methodology.
Such a model can be used to support the modeling of the complex
wireless communication systems. Therefore, the use of such
communication model is an important technique in the construction
of high-performance communication. SystemC has been chosen
because it provides a homogeneous design flow for complex designs
(i.e. SoC and IP-based design). We use a swarm system to validate
CSMA designed model and to show how advantages of incorporating
communication early in the design process. The wireless
communication created through the modeling of CSMA protocol that
can be used to achieve communication between all the agents and to
coordinate access to the shared medium (channel).
Abstract: This paper presents an application of Artificial Neural
Network (ANN) algorithm for improving power system voltage
stability. The training data is obtained by solving several normal and
abnormal conditions using the Linear Programming technique. The
selected objective function gives minimum deviation of the reactive
power control variables, which leads to the maximization of
minimum Eigen value of load flow Jacobian. The considered reactive
power control variables are switchable VAR compensators, OLTC
transformers and excitation of generators. The method has been
implemented on a modified IEEE 30-bus test system. The results
obtain from the test clearly show that the trained neural network is
capable of improving the voltage stability in power system with a
high level of precision and speed.
Abstract: The use of hydroelectric pump-storage system at large
scale, MW-size systems, is already widespread around the world.
Designed for large scale applications, pump-storage station can be
scaled-down for small, remote residential applications. Given the cost
and complexity associated with installing a substation further than
100 miles from the main transmission lines, a remote, independent
and self-sufficient system is by far the most feasible solution. This
article is aiming at the design of wind and solar power generating
system, by means of pumped-storage to replace the wind and /or solar
power systems with a battery bank energy storage. Wind and solar
pumped-storage power generating system can reduce the cost of
power generation system, according to the user's electricity load and
resource condition and also can ensure system reliability of power
supply. Wind and solar pumped-storage power generation system is
well suited for remote residential applications with intermittent wind
and/or solar energy. This type of power systems, installed in these
locations, could be a very good alternative, with economic benefits
and positive social effects. The advantage of pumped storage power
system, where wind power regulation is calculated, shows that a
significant smoothing of the produced power is obtained, resulting in
a power-on-demand system’s capability, concomitant to extra
economic benefits.
Abstract: Implementation of advanced technologies requires
sophisticated instruments that deal with the operation, control,
restoration and protection of rapidly growing power system network
under normal and abnormal conditions. Presently, the applications of
Phasor Measurement Unit (PMU) are widely found in real time
operation, monitoring, controlling and analysis of power system
network as it eliminates the various limitations of supervisory control
and data acquisition system (SCADA) conventionally used in power
system. The use of PMU data is very rapidly increasing its
importance for online and offline analysis. Wide area measurement
system (WAMS) is developed as new technology by use of multiple
PMUs in power system. The present paper proposes a model of
Matlab based PMU using Discrete Fourier Transform (DFT)
algorithm and evaluation of its operation under different
contingencies. In this paper, PMU based two bus system having
WAMS network is presented as a case study.
Abstract: The sea waves carry thousands of GWs of power
globally. Although there are a number of different approaches to
harness offshore energy, they are likely to be expensive, practically
challenging, and vulnerable to storms. Therefore, this paper considers
using the near shore waves for generating mechanical and electrical
power. It introduces two new approaches, the wave manipulation and
using a variable duct turbine, for intercepting very wide wave fronts
and coping with the fluctuations of the wave height and the sea level,
respectively. The first approach effectively allows capturing much
more energy yet with a much narrower turbine rotor. The second
approach allows using a rotor with a smaller radius but captures
energy of higher wave fronts at higher sea levels yet preventing it
from totally submerging. To illustrate the effectiveness of the first
approach, the paper contains a description and the simulation results
of a scale model of a wave manipulator. Then, it includes the results
of testing a physical model of the manipulator and a single duct, axial
flow turbine in a wave flume in the laboratory. The paper also
includes comparisons of theoretical predictions, simulation results,
and wave flume tests with respect to the incident energy, loss in wave
manipulation, minimal loss, brake torque, and the angular velocity.
Abstract: In this paper, we proposed a novel SCR (Silicon Controlled
Rectifier) - based ESD (Electrostatic Discharge) protection device for I/O
and power clamp. The proposed device has a higher holding voltage
characteristic than conventional SCR. These characteristics enable to have
latch-up immunity under normal operating conditions as well as superior full
chip ESD protection. The proposed device was analyzed to figure out
electrical characteristics and tolerance robustness in term of individual
design parameters (D1, D2, D3). They are investigated by using the
Synopsys TCAD simulator. As a result of simulation, holding voltage
increased with different design parameters. The holding voltage of the
proposed device changes from 3.3V to 7.9V. Also, N-Stack structure ESD
device with the high holding voltage is proposed. In the simulation results,
2-stack has holding voltage of 6.8V and 3-stack has holding voltage of
10.5V. The simulation results show that holding voltage of stacking
structure can be larger than the operation voltage of high-voltage
application.