Abstract: Brass terminal, one of the several crude oil and
petroleum products storage/handling facilities in the Niger Delta was
built in the 1980s. Activities at this site, over the years, released
crude oil into this 3 m-deep, 1500 m-long canal lying adjacent to the
terminal with oil floating on it and its sediment heavily polluted. To
ensure effective clean-up, three major activities were planned: site
characterization, bioremediation pilot plant construction and testing
and full-scale bioremediation of contaminated sediment / bank soil by
land farming. The canal was delineated into 12 lots and each
characterized, with reference to the floating oily phase, contaminated
sediment and canal bank soil. As a result of site characterization, a
pilot plant for on-site bioremediation was designed and a treatment
basin constructed for carrying out pilot bioremediation test.
Following a designed sampling protocol, samples from this pilot
plant were collected for analysis at two laboratories as a quality
assurance / quality control check. Results showed that Brass Canal
upstream is contaminated with dark, thick and viscous oily film with
characteristic hydrocarbon smell while downstream, thin oily film
interspersed with water was observed. Sediments were observed to be
dark with mixture of brownish sandy soil with TPH ranging from
17,800 mg/kg in Lot 1 to 88,500 mg/kg in Lot 12 samples. Brass
Canal bank soil was observed to be sandy from ground surface to 3m,
below ground surface (bgs) it was silty-sandy and brownish while
subsurface soil (4-10m bgs) was sandy-clayey and whitish/grayish
with typical hydrocarbon smell. Preliminary results obtained so far
have been very promising but were proprietary. This project is
considered, to the best of technical literature knowledge, the first
large-scale on-site bioremediation project in the Niger Delta region,
Nigeria.
Abstract: Advanced treatments such as forward osmosis (FO)
can be used to separate or reject nutrients from secondary treated
effluents. Forward osmosis uses the chemical potential across the
membrane, which is the osmotic pressure gradient, to induce water to
flow through the membrane from a feed solution (FS) into a draw
solution (DS). The performance of FO is affected by the membrane
characteristics, composition of the FS and DS, and operating
conditions. The aim of this study was to investigate the optimum
velocity and temperature for nutrient rejection and water flux
performance in FO treatments. MgCl2 was used as the DS in the FO
process. The results showed that higher cross flow velocities yielded
higher water fluxes. High rejection of nutrients was achieved by using
a moderate cross flow velocity at 0.25 m/s. Nutrient rejection was
insensitive to temperature variation, whereas water flux was
significantly impacted by it. A temperature of 25°C was found to be
good for nutrient rejection.
Abstract: Many water desalination technologies have been
developed but in general they are energy intensive and have high cost
and adverse environmental impact. Recently, adsorption technology
for water desalination has been investigated showing the potential of
using low temperature waste heat (50-85oC) thus reducing energy
consumption and CO2 emissions. This work mathematically
compares the performance of an adsorption cycle that produces two
useful effects namely, fresh water and cooling using two different
adsorbents, silica-gel and an advanced zeolite material AQSOA-ZO2,
produced by Mitsubishi plastics. It was found that at low chilled
water temperatures, typically below 20oC, the AQSOA-Z02 is more
efficient than silica-gel as the cycle can produce 5.8 m3 of fresh water
per day and 50.1 Rton of cooling per tonne of AQSOA-ZO2. Above
20oC silica-gel is still better as the cycle production reaches 8.4 m3
per day and 62.4 Rton per tonne of silica-gel. These results show the
potential of using the AQSOA-Z02 at low chilled water temperature
for water desalination and cooling applications.
Abstract: Aim of this work is to determine the theoretical and
experimental properties of filament wound glass fiber/epoxy resin
composite pipes with different winding design subjected under
bending. For determination of bending strength of composite samples
three point bending tests were conducted. Good correlation between
theoretical and experimental results has been obtained, where sample
No4 has shown the highest value of bending strength. All samples
have demonstrated matrix cracking and fiber failure followed by
layers delamination during testing. Also, it was found that smaller
winding angles lead to an increase in bending stress. From presented
results good merger between glass fibers and epoxy resin was
confirmed by SEM analysis.
Abstract: This paper presents a numerical investigation of two
horizontally mounted four-lobed swirl pipes in terms of swirl
induction effectiveness into flows passing through them. The swirl
flows induced by the two swirl pipes have the potential to improve
the efficiency of Clean-In-Place procedures in a closed processing
system by local intensification of hydrodynamic impact on the
internal pipe surface. Pressure losses, swirl development within the
two swirl pipe, swirl induction effectiveness, swirl decay and wall
shear stress variation downstream of two swirl pipes are analyzed and
compared. It was found that a shorter length of swirl inducing pipe
used in joint with transition pipes is more effective in swirl induction
than when a longer one is used, in that it has a less constraint to the
induced swirl and results in slightly higher swirl intensity just
downstream of it with the expense of a smaller pressure loss. The
wall shear stress downstream of the shorter swirl pipe is also slightly
larger than that downstream of the longer swirl pipe due to the
slightly higher swirl intensity induced by the shorter swirl pipe. The
advantage of the shorter swirl pipe in terms of swirl induction is more
significant in flows with a larger Reynolds Number.
Abstract: Sol-enhanced Zn-Ni-Al2O3 nanocomposite coatings
were electroplated on mild steel by our newly developed solenhanced
electroplating method. In this method, transparent Al2O3 sol
was added into the acidic Zn-Ni bath to produced Zn-Ni-Al2O3nanocomposite
coatings. The chemical composition, microstructure and
mechanical properties of the composite and alloy coatings deposited
at two different agitation speed were investigated. The structure of all
coatings was single γ-Ni5Zn21 phase. The composite coatings possess
refined crystals with higher microhardness compared to Zn-Ni alloy
coatings. The wear resistance of Zn-Ni coatings was improved
significantly by incorporation of alumina nano particles into the
coatings. Higher agitation speed provided more uniform coatings
with smaller grain sized and slightly higher microhardness.
Considering composite coatings, high agitation speeds may facilitate
co-deposition of alumina in the coatings.
Abstract: Through use of novel modern/rapid processing
techniques such as screen printing and Near-Infrared (NIR) radiative
curing, process time for the sintering of sintered nickel plaques,
applicable to alkaline nickel battery chemistries, has been drastically
reduced from in excess of 200 minutes with conventional convection
methods to below 2 minutes using NIR curing methods. Steps have
also been taken to remove the need for forming gas as a reducing
agent by implementing carbon as an in-situ reducing agent, within the
ink formulation.
Abstract: In this research, TRACE model of Chinshan BWR/4
nuclear power plant (NPP) has been developed for the simulation and
analysis of ultimate response guideline (URG).The main actions of
URG are the depressurization and low pressure water injection of
reactor and containment venting. This research focuses to verify the
URG efficiency under Fukushima-like conditions. TRACE analysis
results show that the URG can keep the PCT below the criteria
1088.7 K under Fukushima-like conditions. It indicated that Chinshan
NPP was safe.
Abstract: Roles of the vegetation to mitigate the erosion of the
stream bed or to facilitate the deposition of the fine sediments by the
species of the aquatic plants were presented. Field investigation on the
estimation of the change of the bed level and the estimation of the flow
characteristics were performed. The results showed that Phragmites
japonica has the mitigation function of 0.3m-0.4m of the erosion in the
range of higher than 1.0m/s of flow velocity at the vegetated region.
Phragmites communis has the mitigation function of 0.2m-0.3m of the
erosion in the range of higher than 0.7m/s of flow velocity at the
vegetated region. Salix gracilistyla has greater role than Phragmites
japonica and Phragmites communis to sustain the stable channel. It
has the mitigation function of 0.4m-0.5m of the erosion in the range of
higher than 1.4m/s of flow velocity. Miscanthus sacchariflorus has a
weak role compared with that of Phragmites japonica and Salix
gracilistyla, but it has still function for sustaining the stable bed. From
these results, the vegetation has effective roles to mitigate the erosion
or to facilitate the deposition of the stream bed.
Abstract: The chemical and physical characteristics of rainwater
harvested from a typical rooftop were progressively studied. The
samples of rainwater collected were analyzed for pH, major ion
concentrations, TDS, turbidity, conductivity. All the Physicochemical
constituents fell within the WHO guideline limits at some points as
rainfall progresses except the pH. All the components of rainwater
quality measured during the study showed higher concentrations
during the early stages of rainfall and reduce as time progresses.
There was a downward trend in terms of pH as rain progressed, with
18% of the samples recording pH below the WHO limit of 6.5-8.0. It
was observed that iron concentration was above the WHO threshold
value of 0.3 mg/l on occasions of heavy rains. The results revealed
that most of physicochemical characteristics of rainwater samples
were generally below the WHO threshold, as such, the rainwater
characteristics showed satisfactory conditions in terms of
physicochemical constituents.
Abstract: This paper addresses the design of hospital Intensive
Care Unit windows for the achievement of visual comfort and energy
savings. The aim was to identify the window size and shading system
configurations that could fulfill daylighting adequacy, avoid glare
and reduce energy consumption. The study focused on addressing the
effect of utilizing different shading systems in association with a
range of Window-to-Wall Ratios (WWR) in different orientations
under the desert clear-sky of Cairo, Egypt.
The results of this study demonstrated that solar penetration is a
critical concern affecting the design of ICU windows in desert
locations, as in Cairo, Egypt. Use of shading systems was found to be
essential in providing acceptable daylight performance and energy
saving. Careful positioning of the ICU window towards a proper
orientation can dramatically improve performance. It was observed
that ICU windows facing the north direction enjoyed the widest range
of successful window configuration possibilities at different WWRs.
ICU windows facing south enjoyed a reasonable number of
configuration options as well. By contrast, the ICU windows facing
the east orientation had a very limited number of options that provide
acceptable performance. These require additional local shading
measures at certain times due to glare incidence. Moreover, use of
horizontal sun breakers and solar screens to protect the ICU windows
proved to be more successful than the other alternatives in a wide
range of Window to Wall Ratios. By contrast, the use of light shelves
and vertical shading devices seemed questionable.
Abstract: The objective of this study is to conduct computational
fluid dynamic (CFD) simulations for evaluating the cooling efficacy
from vegetation implanted in a public park in the Taipei, Taiwan. To
probe the impacts of park renewal by means of adding three pavilions
and supplementary green areas on urban microclimates, the simulated
results have revealed that the park having a higher percentage of green
coverage ratio (GCR) tended to experience a better cooling effect.
These findings can be used to explore the effects of different greening
modifications on urban environments for achieving an effective
thermal comfort in urban public spaces.
Abstract: To solve these problems, we investigated the management system of heating enterprise, including strategic planning based on the balanced scorecard (BSC), quality management in accordance with the standards of the Quality Management System (QMS) ISO 9001 and analysis of the system based on expert judgment using fuzzy inference. To carry out our work we used the theory of fuzzy sets, the QMS in accordance with ISO 9001, BSC, method of construction of business processes according to the notation IDEF0, theory of modeling using Matlab software simulation tools and graphical programming LabVIEW. The results of the work are as follows: We determined possibilities of improving the management of heat-supply plant-based on QMS; after the justification and adaptation of software tool it has been used to automate a series of functions for the management and reduction of resources and for the maintenance of the system up to date; an application for the analysis of the QMS based on fuzzy inference has been created with novel organization of communication software with the application enabling the analysis of relevant data of enterprise management system.
Abstract: In this work, the Ictalurus punctatus species estimated
available physical habitat is compared with the estimated physical
habitat for the same but modified river reach, with the aim of creating
a linear park, along a length of 5 500 m.
To determine the effect of ecological park construction, on
physical habitat of the Lerma river stretch of study, first, the available
habitat for the Ictalurus punctatus species was estimated through the
simulation of the physical habitat, by using surveying, hydraulics,
and habitat information gotten at the river reach in its actual situation.
Second, it was estimated the available habitat for the above species,
upon the simulation of the physical habitat through the proposed
modification for the ecological park creation. Third, it is presented a
comparison between both scenarios in terms of available habitat
estimated for Ictalurus punctatus species, concluding that in cases of
adult and spawning life stages, changes in the channel to create an
ecological park would produce a considerable loss of potentially
usable habitat (PUH), while in the case of the juvenile life stage PUH
remains virtually unchanged, and in the case of life stage fry the PUH
would increase due to the presence of velocities and depths of lesser
magnitude, due to the presence of minor flow rates and lower volume
of the wet channel.
It is expected that habitat modification for linear park construction
may produce the lack of Ictalurus punktatus species conservation at
the river reach of the study.
Abstract: The main objective of this study was to assess the
annual concentration and seasonal variation of benzo(a)pyrene (BaP)
associated with PM10 in an urban site of Győr and in a rural site of
Sarród in the sampling period of 2008–2012. A total of 280 PM10
aerosol samples were collected in each sampling site and analyzed for
BaP by gas chromatography method. The BaP concentrations ranged
from undetected to 8 ng/m3 with the mean value of 1.01 ng/m3 in the
sampling site of Győr, and from undetected to 4.07 ng/m3 with the
mean value of 0.52 ng/m3 in the sampling site of Sarród, respectively.
Relatively higher concentrations of BaP were detected in samples
collected in both sampling sites in the heating seasons compared with
non-heating periods. The annual mean BaP concentrations were
comparable with the published data of different other Hungarian
sites.
Abstract: Biodiesel, as an alternative renewable fuel, has been
receiving increasing attention due to the limited supply of fossil fuels
and the increasing need for energy. Microalgae are promising source
for lipids, which can be converted to biodiesel. The biodiesel
production from microalgae lipids using lipase catalyzed reaction in
supercritical CO2 medium has several advantages over conventional
production processes. However, identifying the optimum microalgae
lipid extraction and transesterification conditions is still a challenge.
In this study, the quality of biodiesel produced from lipids extracted
from Scenedesmus sp. and their enzymatic transesterification using
supercritical carbon dioxide have been investigated. At the optimum
conditions, the highest biodiesel production yield was found to be
82%. The fuel properties of the produced biodiesel, without any
separation step, at optimum reaction condition, were determined and
compared to ASTM standards. The properties were found to comply
with the limits, and showed a low glycerol content, without any
separation step.
Abstract: Continuous upflow filters can combine the nutrient
(nitrogen and phosphate) and suspended solid removal in one unit
process. The contaminant removal could be achieved chemically or
biologically; in both processes the filter removal efficiency depends
on the interaction between the packed filter media and the influent. In
this paper a residence time distribution (RTD) study was carried out
to understand and compare the transfer behaviour of contaminants
through a selected filter media packed in a laboratory-scale
continuous up flow filter; the selected filter media are limestone and
white dolomite. The experimental work was conducted by injecting a
tracer (red drain dye tracer –RDD) into the filtration system and then
measuring the tracer concentration at the outflow as a function of
time; the tracer injection was applied at hydraulic loading rates
(HLRs) (3.8 to 15.2 m h-1). The results were analysed according to
the cumulative distribution function F(t) to estimate the residence
time of the tracer molecules inside the filter media. The mean
residence time (MRT) and variance σ2 are two moments of RTD that
were calculated to compare the RTD characteristics of limestone with
white dolomite. The results showed that the exit-age distribution of
the tracer looks better at HLRs (3.8 to 7.6 m h-1) and (3.8 m h-1) for
limestone and white dolomite respectively. At these HLRs the
cumulative distribution function F(t) revealed that the residence time
of the tracer inside the limestone was longer than in the white
dolomite; whereas all the tracer took 8 minutes to leave the white
dolomite at 3.8 m h-1. On the other hand, the same amount of the
tracer took 10 minutes to leave the limestone at the same HLR. In
conclusion, the determination of the optimal level of hydraulic
loading rate, which achieved the better influent distribution over the
filtration system, helps to identify the applicability of the material as
filter media. Further work will be applied to examine the efficiency
of the limestone and white dolomite for phosphate removal by
pumping a phosphate solution into the filter at HLRs (3.8 to 7.6 m h-1).
Abstract: Evapotranspiration is one of the most important
components of the hydrological cycle. Evapotranspiration (ETo) is an
important variable in water and energy balances on the earth’s
surface, and knowledge of the distribution of ET is a key factor in
hydrology, climatology, agronomy and ecology studies. Many
researchers have a valid relationship, which is a function of climate
factors, to estimate the potential evapotranspiration presented to the
plant water stress or water loss, prevent. The FAO-Penman method
(PM) had been recommended as a standard method. This method
requires many data and these data are not available in every area of
world. So, other methods should be evaluated for these conditions.
When sufficient or reliable data to solve the PM equation are not
available then Hargreaves equation can be used. The Hargreaves
equation (HG) requires only daily mean, maximum and minimum air
temperature extraterrestrial radiation .In this study, Hargreaves
method (HG) were evaluated in 12 stations in the North West region
of Iran. Results of HG and M.HG methods were compared with
results of PM method. Statistical analysis of this comparison showed
that calibration process has had significant effect on efficiency of
Hargreaves method.
Abstract: Remote arid areas of the vast expanses of the African
deserts hold huge subterranean reserves of brackish water resources
waiting for economic development. This work presents design
guidelines as well as initial performance data of new autonomous
solar desalination equipment which could help local communities
produce their own fresh water using solar energy only and, why not,
contribute to transforming desert lands into lush gardens. The output
of solar distillation equipments are typically low and in the range of 3
l/m2/day on the average. This new design with an integrated, water
based, environmentally-friendly solar heat storage system produced 5
l/m2/day in early spring weather. Equipment output during summer
exceeded 9 liters per m2 per day.
Abstract: This paper proposes a linear model for optimizing
domestic energy consumption in Romania. The particularity of the
model is that it is putting in competition both tangible technologies
and thermal insulation projects with different financing modes.
The model is optimizing the energy system by minimizing the
global discounted cost in household sector, by integrating residential
lighting, space heating, hot water, combined space heating – hot
water, as well as space cooling, in a monolithic model. Another
demand sector included is the passenger transport.
This paper focuses on space heating part, analyzing technical and
economic issues related to investment decisions to envelope and
insulate buildings, in order to minimize energy consumption.