Abstract: In recent years demolished concrete waste handling and management is the new primary challenging issue faced by the countries all over the world. It is very challenging and hectic problem that has to be tackled in an indigenous manner, it is desirable to completely recycle demolished concrete waste in order to protect natural resources and reduce environmental pollution. In this research paper an experimental study is carried out to investigate the feasibility and recycling of demolished waste concrete for new construction. The present investigation to be focused on recycling demolished waste materials in order to reduce construction cost and resolving housing problems faced by the low income communities of the world. The crushed demolished concrete wastes is segregated by sieving to obtain required sizes of aggregate, several tests were conducted to determine the aggregate properties before recycling it into new concrete. This research shows that the recycled aggregate that are obtained from site make good quality concrete. The compressive strength test results of partial replacement and full recycled aggregate concrete and are found to be higher than the compressive strength of normal concrete with new aggregate.
Abstract: For fire safety purposes, the fire resistance and the
structural behavior of reinforced concrete members are assessed to
satisfy specific fire performance criteria. The available prescribed
provisions are based on standard fire load. Under various fire
scenarios, engineers are in need of both heat transfer analysis and
structural analysis. For heat transfer analysis, the study proposed a
modified finite difference method to evaluate the temperature profile
within a cross section. The research conducted is limited to concrete
sections exposed to a fire on their one side. The method is based on
the energy conservation principle and a pre-determined power
function of the temperature profile. The power value of 2.7 is found
to be a suitable value for concrete sections. The temperature profiles
of the proposed method are only slightly deviate from those of the
experiment, the FEM and the FDM for various fire loads such as
ASTM E 119, ASTM 1529, BS EN 1991-1-2 and 550 oC. The
proposed method is useful to avoid incontinence of the large matrix
system of the typical finite difference method to solve the
temperature profile. Furthermore, design engineers can simply apply
the proposed method in regular spreadsheet software.
Abstract: Three dimensional simulations are carried out to estimate the effect of wind direction, wind speed and geometry on the flow and dispersion of vehicular pollutant in a street canyon. The pollutant sources are motor vehicles passing between the two buildings. Suitable emission factors for petrol and diesel vehicles at varying vehicle speed are used for the estimation of the rate of emission from the streets. The dispersion of automobile pollutant released from the street is simulated by introducing vehicular emission source term as a fixed-flux boundary condition at the ground level over the road. The emission source term is suitably calculated by adopting emission factors from literature for varying conditions of street traffic. It is observed that increase in wind angle disturbs the symmetric pattern of pollution distribution along the street length. The concentration increases in the far end of the street as compared to the near end.
Abstract: In the stadium structure, the significant dynamic
responses such as resonance or similar behavior can be occurred by
spectator rhythmical activities. Thus, accurate analysis and precise
investigation of stadium structure that is subjected to dynamic loads
are required for practical design and serviceability check of stadium
structures. Moreover, it is desirable to measure and analyze the
dynamic loads of spectator activities because these dynamic loads can
not be easily expressed in numerical formula. In this study, various
dynamic loads induced by spectator movements are measured and
analyzed. These dynamic loads induced by spectators movement of
stadium structure can be classified into the impact load and the
periodic load. These dynamic loads can be expressed as Fourier
harmonic load. And, these dynamic loads could be applied for the
accurate vibration analysis of a stadium structure.
Abstract: Water vapour transport properties of gypsum block
are studied in dependence on relative humidity using inverse analysis
based on genetic algorithm. The computational inverse analysis is
performed for the relative humidity profiles measured along the
longitudinal axis of a rod sample. Within the performed transient
experiment, the studied sample is exposed to two environments with
different relative humidity, whereas the temperature is kept constant.
For the basic gypsum characterisation and for the assessment of input
material parameters necessary for computational application of
genetic algorithm, the basic material properties of gypsum are
measured as well as its thermal and water vapour storage parameters.
On the basis of application of genetic algorithm, the relative
humidity dependent water vapour diffusion coefficient and water
vapour diffusion resistance factor are calculated.
Abstract: An attempt in this paper proposes a re-modification to
the minimum moment approach of resource leveling which is a modified minimum moment approach to the traditional method by
Harris. The method is based on critical path method. The new approach suggests the difference between the methods in the
selection criteria of activity which needs to be shifted for leveling resource histogram. In traditional method, the improvement factor
found first to select the activity for each possible day of shifting. In
modified method maximum value of the product of Resources Rate
and Free Float was found first and improvement factor is then
calculated for that activity which needs to be shifted. In the proposed
method the activity to be selected first for shifting is based on the largest value of resource rate. The process is repeated for all the
remaining activities for possible shifting to get updated histogram.
The proposed method significantly reduces the number of iterations
and is easier for manual computations.
Abstract: In this work, are discussed two formulations of the boundary element method - BEM to perform linear bending analysis of plates reinforced by beams. Both formulations are based on the Kirchhoff's hypothesis and they are obtained from the reciprocity theorem applied to zoned plates, where each sub-region defines a beam or a slab. In the first model the problem values are defined along the interfaces and the external boundary. Then, in order to reduce the number of degrees of freedom kinematics hypothesis are assumed along the beam cross section, leading to a second formulation where the collocation points are defined along the beam skeleton, instead of being placed on interfaces. On these formulations no approximation of the generalized forces along the interface is required. Moreover, compatibility and equilibrium conditions along the interface are automatically imposed by the integral equation. Thus, these formulations require less approximation and the total number of the degree s of freedom is reduced. In the numerical examples are discussed the differences between these two BEM formulations, comparing as well the results to a well-known finite element code.
Abstract: The increasing demand for sufficient and clean
energy forces industrial and service companies to align their strategies towards efficient consumption. This trend refers also to the
residential building sector. There, large amounts of energy consumption are caused by house and facility heating. Many of the
operated hot water heating systems lack hydraulic balanced working
conditions for heat distribution and –transmission and lead to
inefficient heating. Through hydraulic balancing of heating systems,
significant energy savings for primary and secondary energy can be
achieved. This paper addresses the use of KNX-technology (Smart
Buildings) in residential buildings to ensure a dynamic adaption of
hydraulic system's performance, in order to increase the heating
system's efficiency. In this paper, the procedure of heating system
segmentation into hydraulically independent units (meshes) is
presented. Within these meshes, the heating valve are addressed and
controlled by a central facility server. Feasibility criteria towards
such drivers will be named. The dynamic hydraulic balance is
achieved by positioning these valves according to heating loads, that
are generated from the temperature settings in the corresponding
rooms. The energetic advantages of single room heating control
procedures, based on the application FacilityManager, is presented.
Abstract: A passive system "Qanat" is collection of some
underground wells. A mother-well was dug in a place far from the
city where they could reach to the water table maybe 100 meters
underground, they dug other wells to direct water toward the city,
with minimum possible gradient. Using the slope of the earth they
could bring water close to the surface in the city. The source of water
or the appearance of Qanat, land slope and the ownership lines are
the important and effective factors in the formation of routes and the
segment division of lands to the extent that making use of Qanat as
the techniques of extracting underground waters creates a channel of
routes with an organic order and hierarchy coinciding the slope of
land and it also guides the Qanat waters in the tradition texture of salt
desert and border provinces of it. Qanats are excavated in a specified
distinction from each other. The quantity of water provided by
Qanats depends on the kind of land, distance from mountain,
geographical situation of them and the rate of water supply from the
underground land. The rate of underground waters, possibility of
Qanat excavation, number of Qanats and rate of their water supply
from one hand and the quantity of cultivable fertile lands from the
other hand are the important natural factors making the size of cities.
In the same manner the cities with several Qanats have multi central
textures. The location of cities is in direct relation with land quality,
soil fertility and possibility of using underground water by excavating
Qanats. Observing the allowable distance for Qanat watering is a
determining factor for distance between villages and cities.
Topography, land slope, soil quality, watering system, ownership,
kind of cultivation, etc. are the effective factors in directing Qanats
for excavation and guiding water toward the cultivable lands and it
also causes the formation of different textures in land division of
farming provinces. Several divisions such as orderly and wide, inorderly,
thin and long, comb like, etc. are the introduction to organic
order. And at the same time they are complete coincidence with
environmental conditions in the typical development of ecological
architecture and planning in the traditional cities and settlements
order.
Abstract: Structural performance and seismic vulnerability of
masonry buildings in Algeria are investigated in this paper. Structural
classification of such buildings is carried out regarding their
structural elements. Seismicity of Algeria is briefly discussed. Then
vulnerability of masonry buildings and their failure mechanisms in
the Boumerdes earthquake (May, 2003) are examined.
Abstract: This paper highlights the importance of the selection
of the building-s wall material,and the shortcomings of the most
commonly used framed structures with masonry infills .The
objective of this study is investigating the behavior of infill walls as
structural components in existing structures.Structural infill walls are
very important in structural behavior under earthquake effects.
Structural capacity under the effect of earthquake,displacement and
relative story displacement are affected by the structural irregularities
.The presence of nonstructural masonry infill walls can modify
extensively the global seismic behavior of framed buildings .The
stability and integrity of reinforced concrete frames are enhanced by
masonry infill walls. Masonry infill walls alter displacement and
base shear of the frame as well. Short columns have great
importance during earthquakes,because their failure may lead to
additional structural failures and result in total building collapse.
Consequently the effects of short columns are considered in this
study.
Abstract: High Strength Concrete (HSC) is defined as concrete
that meets special combination of performance and uniformity
requirements that cannot be achieved routinely using conventional
constituents and normal mixing, placing, and curing procedures. It is
a highly complex material, which makes modeling its behavior a very
difficult task. This paper aimed to show possible applicability of
Neural Networks (NN) to predict the slump in High Strength
Concrete (HSC). Neural Network models is constructed, trained and
tested using the available test data of 349 different concrete mix
designs of High Strength Concrete (HSC) gathered from a particular
Ready Mix Concrete (RMC) batching plant. The most versatile
Neural Network model is selected to predict the slump in concrete.
The data used in the Neural Network models are arranged in a format
of eight input parameters that cover the Cement, Fly Ash, Sand,
Coarse Aggregate (10 mm), Coarse Aggregate (20 mm), Water,
Super-Plasticizer and Water/Binder ratio. Furthermore, to test the
accuracy for predicting slump in concrete, the final selected model is
further used to test the data of 40 different concrete mix designs of
High Strength Concrete (HSC) taken from the other batching plant.
The results are compared on the basis of error function (or
performance function).
Abstract: The minimal condition for symmetry breaking in morphogenesis of cellular population was investigated using cellular automata based on reaction-diffusion dynamics. In particular, the study looked for the possibility of the emergence of branching structures due to mechanical interactions. The model used two types of cells an external gradient. The results showed that the external gradient influenced movement of cell type-I, also revealed that clusters formed by cells type-II worked as barrier to movement of cells type-I.
Abstract: Method of determining of moisture diffusivity on two types of autoclaved aerated concretes with different bulk density is represented in the paper. On the specimens were measured one dimensional water transport only on liquid phase. Ever evaluation was done from moisture profiles measured in specific times by capacitance moisture meter. All values from capacitance meter were recalculated to moisture content by mass. Moisture diffusivity was determined in dependence on both moisture and temperature. The experiment temperatures were set at values 55, 65, 75 and 85°C.
Abstract: This paper presents a research conducted to investigate the effect of mixing process on polypropylene (PP) modified bitumen mixed with well graded aggregate to form modified bituminous concrete mix. Two mode of mixing, namely dry and wet with different concentration of polymer polypropylene was used with 80/100 pen bitumen, to evaluate the bituminous concrete mix properties. Three percentages of polymer varying from 1-3% by the weight of bitumen was used in this study. Three mixes namely control mix, wet mix and dry mix were prepared. Optimum binder content was calculated considering Marshall Stability, flow, air voids and Marshall Quotient at different bitumen content varying from 4% - 6.5% for control, dry and wet mix. Engineering properties thus obtained at the calculated optimum bitumen content revealed that wet mixing process is advantageous in comparison to dry mixing as it increases the stiffness of the mixture with the increase in polymer content in bitumen. Stiffness value for wet mix increases with the increase in polymer content which is beneficial in terms of rutting. 1% PP dry mix also shows enhanced stiffness, with the air void content limited to 4%.The flow behaviour of dry mix doesn't indicate any major difference with the increase in polymer content revealing that polymer acting as an aggregate only without affecting the viscosity of the binder in the mix. Polypropylene (PP) when interacted with 80 pen base bitumen enhances its performance characteristics which were brought about by altered rheological properties of the modified bitumen. The decrease in flow with the increase in binder content reflects the increase in viscosity of binder which induces the plastic flow in the mix. Workability index indicates that wet mix were easy to compact up to desired void ratio in comparison to dry mix samples.
Abstract: Integral Abutment Bridges (IAB) are defined as
simple or multiple span bridges in which the bridge deck is cast
monolithically with the abutment walls. This kind of bridges are
becoming very popular due to different aspects such as good
response under seismic loading, low initial costs, elimination of
bearings, and less maintenance. However the main issue related to
the analysis of this type of structures is dealing with soil-structure
interaction of the abutment walls and the supporting piles. Various
soil constitutive models have been used in studies of soil-structure
interaction in this kind of structures by researchers. This paper is an
effort to review the implementation of various finite elements model
which explicitly incorporates the nonlinear soil and linear structural
response considering various soil constitutive models and finite
element mesh.
Abstract: In built-up structures, one of the effective ways of
dissipating unwanted vibration is to exploit the occurrence of slip at
the interfaces of structural laminates. The present work focuses on
the dynamic analysis of welded structures. A mathematical
formulation has been developed for the mechanism of slip damping
in layered and welded mild steel beams with unequal thickness
subjected to both periodic and non-periodic forces. It is observed that
a number of vital parameters such as; thickness ratio, pressure
distribution characteristics, relative slip and kinematic co-efficient of
friction at the interfaces, nature of exciting forces, length and
thickness of the beam specimen govern the damping characteristics of
these structures. Experimental verification has been carried out to
validate the analysis and study the effect of these parameters. The
developed damping model for the structure is found to be in fairly
good agreement with the measured data. Finally, the results of the
analysis are discussed and rationalized.
Abstract: Cantilever L-shaped walls are known to be relatively economical as retaining solution. The design starts by proportioning the wall dimensions for which the stability is checked for. A ratio between the lengths of the base and the stem, falling between 0.5 to 0.7 ensure in most case the stability requirements, however, the displacement pattern of the wall in terms of rotations and translations, and the lateral pressure profile, do not have the same figure for all wall’s proportioning, as it is usually assumed. In the present work the results of a numerical analysis are presented, different wall geometries were considered. The results show that the proportioning governs the equilibrium between the instantaneous rotation and the translation of the wall-toe, also, the lateral pressure estimation based on the average value between the at-rest and the active pressure, recommended by most design standards, is found to be not applicable for all walls.
Abstract: The aim of this paper is to discuss a low-cost methodology that can predict traffic flow conflicts and quantitatively rank crash expectancies (based on relative probability) for various traffic facilities. This paper focuses on the application of statistical distributions to model traffic flow and Monte Carlo techniques to simulate traffic and discusses how to create a tool in order to predict the possibility of a traffic crash. A low-cost data collection methodology has been discussed for the heterogeneous traffic flow that exists and a GIS platform has been proposed to thematically represent traffic flow from simulations and the probability of a crash. Furthermore, discussions have been made to reflect the dynamism of the model in reference to its adaptability, adequacy, economy, and efficiency to ensure adoption.
Abstract: This paper presents part of a research into the small
scale modelling of masonry. Small scale testing of masonry has been
carried out by many authors, but few have attempted a systematic
determination of the parameters that affect masonry at a small scale.
The effect of increasing mortar strength and different sand gradings
under compression were investigated. The results show masonry
strength at small scale is influenced by increasing mortar strength and
different sand gradings.