Abstract: The reheating furnace is used to reheat the steel slabs
before the hot-rolling process. The supported system includes the
stationary/moving beams, and the skid buttons which block some
thermal radiation transmitted to the bottom of the slabs. Therefore, it is
important to analyze the steel slab temperature distribution during the
heating period. A three-dimensional mathematical transient heat
transfer model for the prediction of temperature distribution within the
slab has been developed. The effects of different skid button height
(H=60mm, 90mm, and 120mm) and different gap distance between
two slabs (S=50mm, 75mm, and 100mm) on the slab skid mark
formation and temperature profiles are investigated. Comparison with
the in-situ experimental data from Steel Company in Taiwan shows
that the present heat transfer model works well for the prediction of
thermal behavior of the slab in the reheating furnace. It is found that
the skid mark severity decreases with an increase in the skid button
height. The effect of gap distance is important only for the slab edge
planes, while it is insignificant for the slab central planes.
Abstract: A large variety of pipe flange is required in marine
and construction industry. Pipe flanges are usually welded or screwed
to the pipe end and are connected with bolts. This approach is very
simple and widely used for a long time; however, it results in high
development cost and low productivity, and the productions made by
this approach usually have safety problem at the welding area. In this
research, a new approach of forming pipe flange based on cold
forging and floating die concept is presented. This innovative
approach increases the effectiveness of the material usage and save
the time cost compared with conventional welding method. To ensure the dimensional accuracy of the final product, the finite
element analysis (FEA) was carried out to simulate the process of
cold forging, and the orthogonal experiment methods were used to
investigate the influence of four manufacturing factors (pin die angle,
pipe flange angle, rpm, pin die distance from clamp jig) and predicted
the best combination of them. The manufacturing factors were
obtained by numerical and experimental studies and it shows that the
approach is very useful and effective for the forming of pipe flange,
and can be widely used later.
Abstract: This study and the field test comparisons were carried
out on the Algerian Derguna – Setif transmission systems. The
transmission line of normal voltage 225 kV is 65 km long,
transported and uses twin bundle conductors protected with two
shield wires of transposed galvanized steel. An iterative finite-element method is used to solve Poisons
equation. Two algorithms are proposed for satisfying the current
continuity condition and updating the space-charge density. A new approach to the problem of corona discharge in
transmission system has been described in this paper. The effect of
varying the configurations and wires number is also investigated. The
analysis of this steady is important in the design of HVDC
transmission lines. The potential and electric field have been
calculating in locations singular points of the system.
Abstract: Analyzing the relation networks between the hospital
buildings which have complex structure and distinctive spatial
relationships is quite difficult. The hospital buildings which require
specialty in spatial relationship solutions during design and selfinnovation
through the developing technology should survive and
keep giving service even after the disasters such as earthquakes. In
this study, a hospital building where the load-bearing system was
strengthened because of the insufficient earthquake performance and
the construction of an additional building was required to meet the
increasing need for space was discussed and a comparative spatial
evaluation of the hospital building was made with regard to its status
before the change and after the change. For this reason, spatial
organizations of the building before change and after the change were
analyzed by means of Space Syntax method and the effects of the
change on space organization parameters were searched by applying
an analytical procedure. Using Depthmap UCL software,
Connectivity, Visual Mean Depth, Beta and Visual Integration
analyses were conducted. Based on the data obtained after the
analyses, it was seen that the relationships between spaces of the
building increased after the change and the building has become more
explicit and understandable for the occupants. Furthermore, it was
determined according to findings of the analysis that the increase in
depth causes difficulty in perceiving the spaces and the changes
considering this problem generally ease spatial use.
Abstract: This paper studied the flow shop scheduling problem under machine availability constraints. The machines are subject to flexible preventive maintenance activities. The nonresumable scenario for the jobs was considered. That is, when a job is interrupted by an unavailability period of a machine it should be restarted from the beginning. The objective is to minimize the total tardiness time for the jobs and the advance/tardiness for the maintenance activities. To solve the problem, a genetic algorithm was developed and successfully tested and validated on many problem instances. The computational results showed that the new genetic algorithm outperforms another earlier proposed algorithm.
Abstract: The availability to deploy mobile applications for
health care is increasing daily thru different mobile app stores. But
within these capabilities the number of hacking attacks has also
increased, in particular into medical mobile applications. The security
vulnerabilities in medical mobile apps can be triggered by errors in
code, incorrect logic, poor design, among other parameters. This is
usually used by malicious attackers to steal or modify the users’
information. The aim of this research is to analyze the vulnerabilities
detected in mobile medical apps according to risk factor standards
defined by OWASP in 2014.
Abstract: The increasing volume of solid waste generated,
collected and disposed daily complicate adequate management of
solid waste by relevant agency like Niger State Environmental
Protection Agency (NISEPA). In addition, the impacts of solid waste
on the natural environment and human livelihood require
identification of cost-effective ways for sustainable municipal waste
management in Nigeria. These signal the need for identifying
environment-friendly initiative and local solution to address the
problem of municipal solid waste. A research field was secured at
Pago, Minna, Niger State which is located in the guinea savanna belt
of Nigeria, within longitude 60 361 4311 - 4511 and latitude 90 291
37.6111 - .6211 N. Poultry droppings, decomposed household waste
manure and NPK treatments were used. The experimental field was
divided into three replications and four (4) treatments on each
replication making a total of twelve (12) plots. The treatments were
allotted using Randomized Complete Block Design (RCBD) and
Data collected was analyzed using SPSS software and RCBD. The
result depicts variation in plant height and number of leaves at 50%
flowering; Poultry dropping records the highest height while the
number of leaves for waste manure competes fairly well with NPK
treatment. Similarly, the varying treatments significantly increase
vegetable yield, as the control (non-treatment) records the least yield
for the three vegetable samples. Adoption of this organic manure for
cultivation does not only enhance environment quality and attainment
of food security but will contribute to local economic development,
poverty alleviation as well as social inclusion.
Abstract: Cadmium (II) (Cd) is one of the major toxic elemental
pollutants, which is hazardous for humans, animals and plants. γ-
Polyglutamic acid (γ-PGA) is an extracellular biopolymer produced
by several species of Bacillus which has been reported to be an
effective biosorbent for metal ions. The effect of γ-PGA on growth of
rice grown under laboratory conditions was investigated. Rice seeds
were germinated and then grown at 30±1°C on filter paper soaked
with Cd solution and γ-PGA for 7 days. The result showed that Cd
significantly inhibited the growth of roots, shoots by reducing root,
and shoot lengths. Fresh and dry weights also decreased compared
with control; however, the addition of 500 mg·L-1 γ-PGA alleviated
rice seedlings from the adverse effects of Cd. The analysis of
physiological traits revealed that Cd caused a decrease in the total
chlorophyll and soluble protein contents and amylase activities in all
treatments. The Cd content in seedling tissues increased for the Cd
250 μM treatment (P
Abstract: The global demand for long-tailed macaques for
medical experimentation has continued to increase. Fulfillment of
Indonesian export demands has been mostly from natural habitats,
based on a harvesting quota. This quota has been determined
according to the total catch for a given year, and not based on
consideration of any demographic parameters or physical
environmental factors with regard to the animal; hence threatening
the sustainability of the various populations. It is therefore necessary
to formulate a method for calculating a sustainable harvesting quota,
based on population parameters in natural habitats. Considering the
possibility of variations in habitat characteristics and population
parameters, a time series observation of demographic and
physical/biotic parameters, in various habitats, was performed on 13
groups of long-tailed macaques, distributed throughout the West
Java, Lampung and Yogyakarta areas of Indonesia. These provinces
were selected for comparison of the influence of human/tourism
activities. Data on population parameters that was collected included
data on life expectancy according to age class, numbers of
individuals by sex and age class, and ‘ratio of infants to reproductive
females’. The estimation of population growth was based on a
population dynamic growth model: the Leslie matrix. The harvesting
quota was calculated as being the difference between the actual
population size and the MVP (minimum viable population) for each
sex and age class. Observation indicated that there were variations within group size
(24–106 individuals), gender (sex) ratio (1:1 to 1:1.3), life expectancy
value (0.30 to 0.93), and ‘ratio of infants to reproductive females’
(0.23 to 1.56). Results of subsequent calculations showed that
sustainable harvesting quotas for each studied group of long-tailed
macaques, ranged from 29 to 110 individuals. An estimation model
of the MVP for each age class was formulated as Log Y = 0.315 +
0.884 Log Ni (number of individual on ith age class). This study also
found that life expectancy for the juvenile age class was affected by
the humidity under tree stands, and dietary plants’ density at sapling,
pole and tree stages (equation: Y=2.296 – 1.535 RH + 0.002 Kpcg –
0.002 Ktg – 0.001 Kphn, R2 = 89.6% with a significance value of
0.001). By contrast, for the sub-adult-adult age class, life expectancy
was significantly affected by slope (equation: Y=0.377 = 0.012 Kml,
R2 = 50.4%, with significance level of 0.007). The infant-toreproductive-
female ratio was affected by humidity under tree stands,
and dietary plant density at sapling and pole stages (equation: Y = -
1.432 + 2.172 RH – 0.004 Kpcg + 0.003 Ktg, R2 = 82.0% with
significance level of 0.001). This research confirmed the importance
of population parameters in determining the minimum viable
population, and that MVP varied according to habitat characteristics
(especially food availability). It would be difficult therefore, to
formulate a general mathematical equation model for determining a
harvesting quota for the species as a whole.
Abstract: This paper discusses the propagation of sound waves in
air, specifically in narrow rectangular pathways of an occluded-ear
simulator for acoustic measurements. In narrow pathways, both the
speed of sound and the phase of the sound waves are affected by the
damping of the air viscosity. Herein, we propose a new finite-element
method (FEM) that considers the effects of the air viscosity. The
method was developed as an extension of existing FEMs for porous,
sound-absorbing materials. The results of a numerical calculation for a
three-dimensional ear-simulator model using the proposed FEM were
validated by comparing with theoretical lumped-parameter modeling
analysis and standard values.
Abstract: Indonesia has experienced annual forest fires that have
rapidly destroyed and degraded its forests. Fires in the peat swamp
forests of Riau Province, have set the stage for problems to worsen,
this being the ecosystem most prone to fires (which are also the most
difficult, to extinguish). Despite various efforts to curb deforestation,
and forest degradation processes, severe forest fires are still
occurring. To find an effective solution, the basic causes of the
problems must be identified. It is therefore critical to have an indepth
understanding of the underlying causal factors that have
contributed to deforestation and forest degradation as a whole, in
order to attain reductions in their rates. An assessment of the drivers of deforestation and forest
degradation was carried out, in order to design and implement
measures that could slow these destructive processes. Research was
conducted in Giam Siak Kecil–Bukit Batu Biosphere Reserve
(GSKBB BR), in the Riau Province of Sumatera, Indonesia. A
biosphere reserve was selected as the study site because such reserves
aim to reconcile conservation with sustainable development. A
biosphere reserve should promote a range of local human activities,
together with development values that are in line spatially and
economically with the area conservation values, through use of a
zoning system. Moreover, GSKBB BR is an area with vast peatlands,
and is experiencing forest fires annually. Various factors were
analysed to assess the drivers of deforestation and forest degradation
in GSKBB BR; data were collected from focus group discussions
with stakeholders, key informant interviews with key stakeholders,
field observation and a literature review. Landsat satellite imagery was used to map forest-cover changes
for various periods. Analysis of landsat images, taken during the
period 2010-2014, revealed that within the non-protected area of core
zone, there was a trend towards decreasing peat swamp forest areas,
increasing land clearance, and increasing areas of community oilpalm
and rubber plantations. Fire was used for land clearing and most
of the forest fires occurred in the most populous area (the transition
area). The study found a relationship between the deforested/
degraded areas, and certain distance variables, i.e. distance from
roads, villages and the borders between the core area and the buffer
zone. The further the distance from the core area of the reserve, the
higher was the degree of deforestation and forest degradation. Research findings suggested that agricultural expansion may be
the direct cause of deforestation and forest degradation in the reserve,
whereas socio-economic factors were the underlying driver of forest
cover changes; such factors consisting of a combination of sociocultural,
infrastructural, technological, institutional (policy and governance), demographic (population pressure) and economic
(market demand) considerations. These findings indicated that local
factors/problems were the critical causes of deforestation and
degradation in GSKBB BR. This research therefore concluded that
reductions in deforestation and forest degradation in GSKBB BR
could be achieved through ‘local actor’-tailored approaches such as
community empowerment.
Abstract: The recent interest in alternative and renewable
energy systems results in increased installed capacity ratio of such
systems in total energy production of the world. Specifically, Wind
Energy Conversion Systems (WECS) draw significant attention
among possible alternative energy options, recently. On the contrary
of the positive points of penetrating WECS in all over the world in
terms of environment protection, energy independence of the
countries, etc., there are significant problems to be solved for the grid
connection of large scale WECS. The reactive power regulation,
voltage variation suppression, etc. can be presented as major issues to
be considered in this regard. Thus, this paper evaluates the
application of a Static VAr Compensator (SVC) unit for the reactive
power regulation and operation continuity of WECS during a fault
condition. The system is modeled employing the IEEE 13 node test
system. Thus, it is possible to evaluate the system performance with
an overall grid simulation model close to real grid systems. The
overall simulation model is developed in
MATLAB/Simulink/SimPowerSystems® environments and the
obtained results effectively match the target of the provided study.
Abstract: In this paper, the secure BioSemantic Scheme is
presented to bridge biological/biomedical research problems and
computational solutions via semantic computing. Due to the diversity
of problems in various research fields, the semantic capability
description language (SCDL) plays and important role as a common
language and generic form for problem formalization. SCDL is
expected the essential for future semantic and logical computing in
Biosemantic field. We show several example to Biomedical problems
in this paper. Moreover, in the coming age of cloud computing, the
security problem is considered to be crucial issue and we presented a
practical scheme to cope with this problem.
Abstract: This paper describes a new approach which can be
used to interpret the experimental creep deformation data obtained
from miniaturized thin plate bending specimen test to the
corresponding uniaxial data based on an inversed application of the
reference stress method. The geometry of the thin plate is fully
defined by the span of the support, l, the width, b, and the thickness,
d. Firstly, analytical solutions for the steady-state, load-line creep
deformation rate of the thin plates for a Norton’s power law under
plane stress (b→0) and plane strain (b→∞) conditions were obtained,
from which it can be seen that the load-line deformation rate of the
thin plate under plane-stress conditions is much higher than that
under the plane-strain conditions. Since analytical solution is not
available for the plates with random b-values, finite element (FE)
analyses are used to obtain the solutions. Based on the FE results
obtained for various b/l ratios and creep exponent, n, as well as the
analytical solutions under plane stress and plane strain conditions, an
approximate, numerical solutions for the deformation rate are
obtained by curve fitting. Using these solutions, a reference stress
method is utilised to establish the conversion relationships between
the applied load and the equivalent uniaxial stress and between the
creep deformations of thin plate and the equivalent uniaxial creep
strains. Finally, the accuracy of the empirical solution was assessed
by using a set of “theoretical” experimental data.
Abstract: This paper investigates the parametric stability of an
axially moving web subjected to non-uniform in-plane edge
excitations on two opposite, simply-supported edges. The web is
modeled as a viscoelastic plate whose constitutive relation obeys the
Kelvin-Voigt model, and the in-plane edge excitations are expressed
as the sum of a static tension and a periodical perturbation. Due to the
in-plane edge excitations, the moving plate may bring about
parametric instability under certain situations. First, the in-plane
stresses of the plate due to the non-uniform edge excitations are
determined by solving the in-plane forced vibration problem. Then,
the dependence on the spatial coordinates in the equation of transverse
motion is eliminated by the generalized Galerkin method, which
results in a set of discretized system equations in time. Finally, the
method of multiple scales is utilized to solve the set of system
equations analytically if the periodical perturbation of the in-plane
edge excitations is much smaller as compared with the static tension of
the plate, from which the stability boundaries of the moving plate are
obtained. Numerical results reveal that only combination resonances
of the summed-type appear under the in-plane edge excitations
considered in this work.
Abstract: In this paper, influence of harmonics on medium
voltage distribution system of Bogazici Electricity Distribution Inc.
(BEDAS) which takes place at Istanbul/Turkey is investigated. A ring
network consisting of residential loads is taken into account for this
study. Real system parameters and measurement results are used for
simulations. Also, probable working conditions of the system are
analyzed for 50%, 75%, and 100% loading of transformers with
similar harmonic contents. Results of the study are exhibited the
influence of nonlinear loads on %THDV, P.F. and technical losses of
the medium voltage distribution system.
Abstract: This paper describes a novel sensor device, a pressure
pulse wave meter, which uses a bidirectional condenser microphone.
The microphone work as a microphone as well as a sensor with high
gain over a wide frequency range; they are also highly reliable and
economic. Currently aging is becoming a serious social issue in Japan causing
increased medical expenses in the country. Hence, it is important for
elderly citizens to check health condition at home, and to care the
health conditions through daily monitoring. Given this circumstances,
we developed a novel pressure pulse wave meter based on a
bidirectional condenser microphone: this device is used as a measuring
instrument of health conditions.
Abstract: In recent research copper and manganese systems
were found to be the most active in CO and organic compounds
oxidation among the base catalysts. The mixed copper manganese
oxide has been widely studied in oxidation reactions because of their
higher activity at low temperatures in comparison with single oxide
catalysts. The results showed that the formation of spinel
CuxMn3−xO4 in the oxidized catalyst is responsible for the activity
even at room temperature. That is why the most of the investigations
are focused on the hopcalite catalyst (CuMn2O4) as the best coppermanganese
catalyst. Now it’s known that this is true only for CO
oxidation, but not for mixture of CO and VOCs. The purpose of this
study is to investigate the alumina supported copper-manganese
catalysts with different Cu/Mn molar ratio in terms of oxidation of
CO, methanol and dimethyl ether. The catalysts were prepared by impregnation of γ-Al2O3 with
copper and manganese nitrates and the catalytic activity
measurements were carried out in two stage continuous flow
equipment with an adiabatic reactor for simultaneous oxidation of all
compounds under the conditions closest possible to the industrial. Gas
mixtures on the input and output of the reactor were analyzed with a
gas chromatograph, equipped with FID and TCD detectors. The
texture characteristics were determined by low-temperature (- 196oС)
nitrogen adsorption in a Quantachrome Instruments NOVA 1200e
(USA) specific surface area & pore analyzer. Thermal, XRD and
TPR analyses were performed. It was established that the active component of the mixed Cu-
Mn/γ–alumina catalysts strongly depends on the Cu/Mn molar ratio.
Highly active alumina supported Cu-Mn catalysts for CO, methanol
and DME oxidation were synthesized. While the hopcalite is the best
catalyst for CO oxidation, the best compromise for simultaneous
oxidation of all components is the catalyst with Cu/Mn molar ratio
1:5.
Abstract: Studying stress and strain trends in the femur and
recognizing femur failure mechanism is very important for
preventing hip fracture in the elderly. The aim of this study was to
identify high stress and strain regions in the femur during normal
walking and falling to find the mechanical behavior and failure
mechanism of the femur. We developed a finite element model of the
femur from the subject’s quantitative computed tomography (QCT)
image and used it to identify potentially high stress and strain regions
during the single-leg stance and the sideways fall. It was found that
fracture may initiate from the superior region of femoral neck and
propagate to the inferior region during a high impact force such as
sideways fall. The results of this study showed that the femur bone is
more sensitive to strain than stress which indicates the effect of
strain, in addition to effect of stress, should be considered for failure
analysis.
Abstract: In this study, lipid-deprived residuals of microalgae
were hydrolyzed for the production of reducing sugars by using the
recombinant Bacillus cellulosome, carrying eight genes from the
Clostridium thermocellum ATCC27405. The obtained cellulosome
was found to exist mostly in the broth supernatant with a cellulosome
activity of 2.4 U/mL. Furthermore, the Michaelis-Menten constant
(Km) and Vmax of cellulosome were found to be 14.832 g/L and 3.522
U/mL. The activation energy of the cellulosome to hydrolyze
microalgae LDRs was calculated as 32.804 kJ/mol.