Abstract: Sisal leaves were subjected to enzymatic retting
method to extract the sisal fibre. A portion of the fibre was pretreated
with alkali (NaOH), and further treated with benzoyl chloride
and silane treatment reagents. Both the treated and untreated Sisal
fibre composites were used to fabricate the composite by hand lay-up
technique using unsaturated polyester resin. Tensile, flexural, water
absorption, density, thickness swelling and chemical resistant tests
were conducted and evaluated on the composites. Results obtained
for all the parameters showed an increase in the treated fibre
compared to untreated fibre. FT-IR spectra results ascertained the
inclusion of benzoyl and silane groups on the fibre surface. Scanning
electron microscopy (SEM) result obtained showed variation in the
morphology of the treated and untreated fibre. Chemical modification
was found to improve adhesion of the fibre to the matrix, as well as
physico-mechanical properties of the composites.
Abstract: A university-wide survey to obtain baseline data
regarding the perceptions of key terms related to e-learning and
distance learning among students, faculty and staff was conducted to
help achieve the goals of Princess Nourah bint Abdulrahman
University’s and the Kingdom of Saudi Arabia’s National Center for
e-learning and Distance Learning. This paper comprises a relevant
literature review, the survey methodology, preliminary data analysis,
discussion, and recommendations for further research. The major
findings indicate a deep and wide differentiation of understanding
among users of critical key terms.
Abstract: This paper presents the design and analysis of Liquid Crystal (LC) based tunable reflectarray antenna with slot embedded patch element configurations within X-band frequency range. The slots are shown to modify the surface current distribution on the patch element of reflectarray which causes the resonant patch element to provide different resonant frequencies depending on the slot dimensions. The simulated results are supported and verified by waveguide scattering parameter measurements of different reflectarray unit cells. Different rectangular slots on patch element have been fabricated and a change in resonant frequency from 10.46GHz to 8.78GHz has been demonstrated as the width of the rectangular slot is varied from 0.2W to 0.6W. The rectangular slot in the center of the patch element has also been utilized for the frequency tunable reflectarray antenna design based on K-15 Nematic LC. For the active reflectarray antenna design, a frequency tunability of 1.2% from 10GHz to 9.88GHz has been demonstrated with a dynamic phase range of 103° provided by the measured scattering parameter results. Time consumed by liquid crystals for reconfiguration, which is one of the drawback of LC based design, has also been disused in this paper.
Abstract: Growth and remodeling of biological structures have
gained lots of attention over the past decades. Determining the
response of living tissues to mechanical loads is necessary for a wide
range of developing fields such as prosthetics design or computerassisted
surgical interventions. It is a well-known fact that biological
structures are never stress-free, even when externally unloaded. The
exact origin of these residual stresses is not clear, but theoretically,
growth is one of the main sources. Extracting body organ’s shapes
from medical imaging does not produce any information regarding
the existing residual stresses in that organ. The simplest cause of such
stresses is gravity since an organ grows under its influence from
birth. Ignoring such residual stresses might cause erroneous results in
numerical simulations. Accounting for residual stresses due to tissue
growth can improve the accuracy of mechanical analysis results. This
paper presents an original computational framework based on gradual
growth to determine the residual stresses due to growth. To illustrate
the method, we apply it to a finite element model of a healthy human
face reconstructed from medical images. The distribution of residual
stress in facial tissues is computed, which can overcome the effect of
gravity and maintain tissues firmness. Our assumption is that tissue
wrinkles caused by aging could be a consequence of decreasing
residual stress and thus not counteracting gravity. Taking into
account these stresses seems therefore extremely important in
maxillofacial surgery. It would indeed help surgeons to estimate
tissues changes after surgery.
Abstract: The inverted pendulum system is a classic control
problem that is used in universities around the world. It is a suitable
process to test prototype controllers due to its high non-linearities and
lack of stability. The inverted pendulum represents a challenging
control problem, which continually moves toward an uncontrolled
state. This paper presents the possibility of balancing an inverted
pendulum system using sliding mode control (SMC). The goal is to
determine which control strategy delivers better performance with
respect to pendulum’s angle and cart's position. Therefore,
proportional-integral-derivative (PID) is used for comparison. Results
have proven SMC control produced better response compared to PID
control in both normal and noisy systems.
Abstract: This paper aims to analysis the behavior of DC corona
discharge in wire-to-plate electrostatic precipitators (ESP). Currentvoltage
curves are particularly analyzed. Experimental results show
that discharge current is strongly affected by the applied voltage. The proposed method of current identification is to use the method
of least squares. Least squares problems that of into two categories:
linear or ordinary least squares and non-linear least squares,
depending on whether or not the residuals are linear in all unknowns.
The linear least-squares problem occurs in statistical regression
analysis; it has a closed-form solution. A closed-form solution (or
closed form expression) is any formula that can be evaluated in a
finite number of standard operations. The non-linear problem has no
closed-form solution and is usually solved by iterative.
Abstract: In the present research, whole meal barley flour
(WBF) was supplemented with gelatinized corn flour (GCF) in 0 and
30%. Whole meal wheat flour (WWF) was mixed with defatted rice
bran (DRB) to produce 0, 20, 25, and 30% replacement levels.
Rheological properties of dough were studied. Thermal properties
and starch crystallinity of flours were evaluated. Flat bread, balady
bread and pie were prepared from the different flour blends. The
different bakeries were sensory evaluated. Color of raw materials and
crust of bakery products were determined. Nutrients contents of raw
flours and food products were assessed. Results showed that addition
of GCF to WBF increased the viscosity and falling number of the
produced dough. Water absorption, dough development time and
dough stability increased with increasing the level of DRB in dough
while, weakening and mixing tolerance index decreased.
Extensibility and energy decreased, while, resistance to extension
increased as DRB level increased. Gelatinized temperature of WWF,
WBF, GCF, and DRB were 13.26, 35.09, 28.33, and 39.63,
respectively. Starch crystallinity was affected when DRB was added
to WWF. The highest protein content was present in balady bread
made from 70% WWF and 30% DRB. The highest calcium,
phosphorus, and potassium levels were present in products made
from 100% WBF. Sensory attributes of the products were slightly
affected by adding DRB and GCF. Conclusion: Addition of DRB or
GCF to WWF or WBF, respectively affect the physical, chemical,
rheological and sensory properties of balady bread, flat bread, and pie
while improved their nutritive values.
Abstract: Bezier curves have useful properties for path
generation problem, for instance, it can generate the reference
trajectory for vehicles to satisfy the path constraints. Both algorithms
join cubic Bezier curve segment smoothly to generate the path. Some
of the useful properties of Bezier are curvature. In mathematics,
curvature is the amount by which a geometric object deviates from
being flat, or straight in the case of a line. Another extrinsic example
of curvature is a circle, where the curvature is equal to the reciprocal
of its radius at any point on the circle. The smaller the radius, the
higher the curvature thus the vehicle needs to bend sharply. In this
study, we use Bezier curve to fit highway-like curve. We use
different approach to find the best approximation for the curve so that
it will resembles highway-like curve. We compute curvature value by
analytical differentiation of the Bezier Curve. We will then compute
the maximum speed for driving using the curvature information
obtained. Our research works on some assumptions; first, the Bezier
curve estimates the real shape of the curve which can be verified
visually. Even though, fitting process of Bezier curve does not
interpolate exactly on the curve of interest, we believe that the
estimation of speed are acceptable. We verified our result with the
manual calculation of the curvature from the map.
Abstract: This report examines the current state of human gait
simulator development based on the human hip joint model. This unit
will create a database of human gait types, useful for setting up and
calibrating Mechano devices, as well as the creation of new systems
of rehabilitation, exoskeletons and walking robots. The system has
many opportunities to configure the dimensions and stiffness, while
maintaining relative simplicity.
Abstract: Opportunistic Routing (OR) increases the
transmission reliability and network throughput. Traditional routing
protocols preselects one or more predetermined nodes before
transmission starts and uses a predetermined neighbor to forward a
packet in each hop. The opportunistic routing overcomes the
drawback of unreliable wireless transmission by broadcasting one
transmission can be overheard by manifold neighbors. The first
cooperation-optimal protocol for Multirate OR (COMO) used to
achieve social efficiency and prevent the selfish behavior of the
nodes. The novel link-correlation-aware OR improves the
performance by exploiting the miscellaneous low correlated forward
links. Context aware Adaptive OR (CAOR) uses active suppression
mechanism to reduce packet duplication. The Context-aware OR
(COR) can provide efficient routing in mobile networks. By using
Cooperative Opportunistic Routing in Mobile Ad hoc Networks
(CORMAN), the problem of opportunistic data transfer can be
tackled. While comparing to all the protocols, COMO is the best as it
achieves social efficiency and prevents the selfish behavior of the
nodes.
Abstract: The research on thermoelectric has been a blooming field of research for the latest decade, owing to large amount of heat source available to be harvested, being eco-friendly and static in operation. This paper provides the performance of thermoelectric generator (TEG) with bulk material of bismuth telluride, Bi2Te3. Later, the performance of the TEGs is evaluated by considering attaching the TEGs on a plastic (polyethylene sheet) in contrast to the common method of attaching the TEGs on the metal surface.
Abstract: The post-rain puddles problem that occurs in the first
yard of Prambanan Temple are often disturbing visitor activity. A
poodle layer and a drainage system had ever built to avoid such a
problem, but puddles still did not stop appearing after rain.
Permeability parameter needs to be determined by using a simpler
procedure to find exact method of solution. The instrument modelling
was proposed according to the development of field permeability
testing instrument. This experiment used a proposed Constant
Discharge method. Constant Discharge method used a tube poured
with constant water flow from unsaturated until saturated soil
condition. Volumetric water content (θ) were monitored by soil
moisture measurement device. The results were correlations between
k and θ which were drawn by numerical approach from Van
Genutchen model. Parameters θr optimum value obtained from the
test was at very dry soil. Coefficient of permeability with a density of
19.8 kN/m3 for unsaturated conditions was in range of 3 x 10-6
cm/sec (Sr=68%) until 9.98 x 10-4 cm/sec (Sr=82%). The equipment
and testing procedure developed in this research was quite effective,
simple and easy to be implemented on determining field soil
permeability coefficient value of sandy soil. Using constant discharge
method in proposed permeability test, value of permeability
coefficient under unsaturated condition can be obtained without
establish soil water characteristic curve.
Abstract: The main cause of Alzheimer disease (AD) was
believed to be mainly due to the accumulation of free radicals owing
to oxidative stress (OS) in brain tissue. The mechanism of the
neurotoxicity of Aluminum chloride (AlCl3) induced AD in
hippocampus Albino wister rat brain tissue, the curative & the
protective effects of Lipidium sativum group (LS) water extract were
assessed after 8 weeks by attenuated total reflection spectroscopy
ATR-IR and histologically by light microscope. ATR-IR results
revealed that the membrane phospholipid undergo free radical
attacks, mediated by AlCl3, primary affects the polyunsaturated fatty
acids indicated by the increased of the olefinic -C=CH sub-band area
around 3012 cm-1 from the curve fitting analysis. The narrowing in
the half band width (HBW) of the sνCH2 sub-band around 2852 cm-1
due to Al intoxication indicates the presence of trans form fatty acids
rather than gauch rotomer. The degradation of hydrocarbon chain to
shorter chain length, increasing in membrane fluidity, disorder, and
decreasing in lipid polarity in AlCl3 group indicated by the detected
changes in certain calculated area ratios compared to the control.
Administration of LS was greatly improved these parameters
compared to the AlCl3 group. Al influences the Aβ aggregation and
plaque formation, which in turn interferes to and disrupts the
membrane structure. The results also showed a marked increase in
the β-parallel and antiparallel structure, that characterize the Aβ
formation in Al-induced AD hippocampal brain tissue, indicated by
the detected increase in both amide I sub-bands around 1674, 1692
cm-1. This drastic increase in Aβ formation was greatly reduced in the
curative and protective groups compared to the AlCl3 group and
approached nearly the control values. These results supported too by
the light microscope. AlCl3 group showed significant marked
degenerative changes in hippocampal neurons. Most cells appeared
small, shrieked and deformed. Interestingly, the administration of LS
in curative and protective groups markedly decreases the amount of
degenerated cells compared to the non-treated group. In addition, the
intensity of congo red stained cells was decreased. Hippocampal
neurons looked more/or less similar to those of control. This study showed a promising therapeutic effect of Lipidium
sativum group (LS) on AD rat model that seriously overcome the
signs of oxidative stress on membrane lipid and restore the protein
misfolding.
Abstract: This paper focuses on the questions raised through the
work of Unit 5: ‘In/Out Crisis, emergent and adaptive’; an
architectural research-based studio at [ARC] University of Nicosia. Students were asked to delve into state of Art Technologies in
order to propose sustainable Emergent and Adaptive Architectures
and Urbanities, the resulting unprecedented spatial conditions and
atmospheres of the emergent new ways of living are deemed to be the
ultimate aim of the investigation. Students explored a variety of sites
and crisis conditions seen through their primary ingredient identified
as soil, water and air and their paired combination. Within this
methodology, crisis is seen as a mechanism for allowing an
emergence of new and fascinating ultimate sustainable future cultures
and cities by taking advantage of the primary materiality of the sites.
Abstract: A geoelectric survey was carried out in some parts of
Angwan Gwari, an outskirt of Lapai Local Government Area on
Niger State which belongs to the Nigerian Basement Complex, with
the aim of evaluating the soil corrosivity, aquifer transmissivity and
protective capacity of the area from which aquifer characterisation
was made. The G41 Resistivity Meter was employed to obtain fifteen
Schlumberger Vertical Electrical Sounding data along profiles in a
square grid network. The data were processed using interpex 1-D
sounding inversion software, which gives vertical electrical sounding
curves with layered model comprising of the apparent resistivities,
overburden thicknesses, and depth. This information was used to
evaluate longitudinal conductance and transmissivities of the layers.
The results show generally low resistivities across the survey area
and an average longitudinal conductance variation from
0.0237Siemens in VES 6 to 0.1261Siemens in VES 15 with almost
the entire area giving values less than 1.0 Siemens. The average
transmissivity values range from 96.45 Ω.m2 in VES 4 to 299070
Ω.m2 in VES 1. All but VES 4 and VES14 had an average
overburden greater than 400 Ω.m2, these results suggest that the
aquifers are highly permeable to fluid movement within, leading to
the possibility of enhanced migration and circulation of contaminants
in the groundwater system and that the area is generally corrosive.
Abstract: In order to be competitive, companies have to reduce
their production costs while meeting increasing quality requirements.
Therefore, companies try to plan their assembly processes as detailed
as possible. However, increasing product individualization leading to
a higher number of variants, smaller batch sizes and shorter product
life cycles raise the question to what extent the effort of detailed
planning is still justified. An important approach in this field of
research is the concept of determining the economic planning depth
for assembly process planning based on production specific
influencing factors. In this paper first solution hypotheses as well as a
first draft of the resulting method will be presented.
Abstract: In this glasshouse study, we developed a new imagebased
non-destructive technique for detecting leaf P status of
different crops such as cotton, tomato and lettuce. The plants were
grown on a nutrient solution containing different P concentrations,
e.g. 0%, 50% and 100% of recommended P concentration (P0 = no P,
L; P1 = 2.5 mL 10 L-1 of P and P2 = 5 mL 10 L-1 of P). After 7 weeks
of treatment, the plants were harvested and data on leaf P contents
were collected using the standard destructive laboratory method and
at the same time leaf images were collected by a handheld crop image
sensor. We calculated leaf area, leaf perimeter and RGB (red, green
and blue) values of these images. These data were further used in
linear discriminant analysis (LDA) to estimate leaf P contents, which
successfully classified these plants on the basis of leaf P contents.
The data indicated that P deficiency in crop plants can be predicted
using leaf image and morphological data. Our proposed nondestructive
imaging method is precise in estimating P requirements of
different crop species.
Abstract: Background: To improve the delivery of paediatric
healthcare in low resource settings, Community Health Workers
(CHW) have been provided with a paper-based set of protocols
known as Community Case Management (CCM). Yet research has
shown that CHW adherence to CCM guidelines is poor, ultimately
impacting health service delivery. Digitising the CCM guidelines via
mobile technology is argued in extant literature to improve CHW
adherence. However, little research exist which outlines how (a) this
process can be digitised and (b) adherence could be improved as a
result. Aim: To explore how an electronic mobile version of CCM
(eCCM) can overcome issues associated with the paper-based CCM
protocol (inadequate adherence to guidelines) vis-à-vis service
blueprinting. This service blueprint will outline how (a) the CCM
process can be digitised using mobile Clinical Decision Support
Systems software to support clinical decision-making and (b)
adherence can be improved as a result. Method: Development of a
single service blueprint for a standalone application which visually
depicts the service processes (eCCM) when supporting the CHWs,
using an application known as Supporting LIFE (SL eCCM app) as
an exemplar. Results: A service blueprint is developed which
illustrates how the SL eCCM app can be utilised by CHWs to assist
with the delivery of healthcare services to children. Leveraging
smartphone technologies can (a) provide CHWs with just-in-time
data to assist with their decision making at the point-of-care and (b)
improve CHW adherence to CCM guidelines. Conclusions: The
development of the eCCM opens up opportunities for the CHWs to
leverage the inherent benefit of mobile devices to assist them with
health service delivery in rural settings. To ensure that benefits are
achieved, it is imperative to comprehend the functionality and form
of the eCCM service process. By creating such a service blueprint for
an eCCM approach, CHWs are provided with a clear picture
regarding the role of the eCCM solution, often resulting in buy-in
from the end-users.
Abstract: Household waste form a larger proportion of waste
generated across the state, accumulation of organic waste is an
apparent problem and the existing dump sites could be overstress.
Niger state has abundant arable land and water resources thus should
be one of the highest producers of agricultural crops in the country.
However, the major challenge to agricultural sector today is loss of
soil nutrient coupled with high cost of fertilizer. These have
continued to increase the use of fertilizer and decomposed solid waste
for enhance agricultural yield, which have varying effects on the soil
as well a threat to human livelihood. Consequently, vegetable yield
samples from poultry droppings, decomposed household waste
manure, NPK treatments and control from each replication were
subjected to proximate analysis to determine the nutritional and antinutritional
component as well as heavy metal concentration. Data
collected was analyzed using SPSS software and Randomized
complete Block Design means were compared. The result shows that
the treatments do not devoid the concentrations of any nutritional
components while the anti-nutritional analysis proved that NPK had
higher oxalate content than control and organic treats. The
concentration of lead and cadmium are within safe permissible level
while the mercury level exceeded the FAO/WHO maximum
permissible limit for the entire treatments depicts the need for urgent
intervention to minimize mercury levels in soil and manure in order
to mitigate its toxic effect. Thus, eco-agriculture should be widely
accepted and promoted by the stakeholders for soil amendment,
higher yield, strategies for sustainable environmental protection, food
security, poverty eradication, attainment of sustainable development
and healthy livelihood.
Abstract: The need to save time and cost of soil testing at the
planning stage of road work has necessitated developing predictive
models. This study proposes a model for predicting the dry density of
lateritic soils stabilized with corn cob ash (CCA) and blended cement
- CCA. Lateritic soil was first stabilized with CCA at 1.5, 3.0, 4.5 and
6% of the weight of soil and then stabilized with the same
proportions as replacement for cement. Dry density, specific gravity,
maximum degree of saturation and moisture content were determined
for each stabilized soil specimen, following standard procedure.
Polynomial equations containing alpha and beta parameters for CCA
and blended CCA-cement were developed. Experimental values were
correlated with the values predicted from the Matlab curve fitting
tool, and the Solver function of Microsoft Excel 2010. The correlation
coefficient (R2) of 0.86 was obtained indicating that the model could
be accepted in predicting the maximum dry density of CCA stabilized
soils to facilitate quick decision making in roadworks.