Abstract: Concrete pavement has superior durability and longer
structural life than asphalt pavement. Concrete pavement requires
less maintenance compared to asphalt pavement which requires maintenance and major rehabilitation. Use of the concrete pavement
has been grown over the past decade in developing countries. Fibre reinforced concrete (FRC) has been successfully used in design of concrete pavement in past decade. In this research, the effect of fibre
volume fraction in modulus of rupture, load-deflection, equivalent flexural strength (fe,3) and the equivalent flexural strength ratio (Re,3)
has been used in different fibre volume fraction. Crimped-type flat
steel fibre of size 50 x 2.0 x 0.6 mm was used with 1.0%, 1.5% and 2.0% volume fraction. Beam specimens of size 500 x 100 x 100 mm were used for flexural as well as with JCI method for analysis flexural toughness, equivalent flexural strength. It was obtained as the 2% fibre volume fractions; reduce 45% of the concrete pavement
thickness.
Abstract: We present an explicit expression to estimate driving voltage attenuation through RC networks representation of an ultrahigh- speed image sensor. Elmore delay metric for a fundamental RC chain is employed as the first-order approximation. By application of dimensional analysis to SPICE simulation data, we found a simple expression that significantly improves the accuracy of the approximation. Estimation error of the resultant expression for uniform RC networks is less than 2%. Similarly, another simple closed-form model to estimate 50 % delay through fundamental RC networks is also derived with sufficient accuracy. The framework of this analysis can be extended to address delay or attenuation issues of other VLSI structures.
Abstract: To investigates the effect of fiberglass clamping
process improvement on drape simulation prediction. This has
great effect on the mould and the fiber during manufacturing
process. This also, improves the fiber strain, the quality of the
fiber orientation in the area of folding and wrinkles formation
during the press-forming process. Drape simulation software
tool was used to digitalize the process, noting the formation
problems on the contour sensitive part. This was compared
with the real life clamping processes using single and double
frame set-ups to observe the effects. Also, restrains are
introduced by using clips, and the G-clamps with predetermine
revolution to; restrain the fabric deformation during the
forming process.The incorporation of clamping and fabric
restrain deformation improved on the prediction of the
simulation tool. Therefore, for effective forming process,
incorporation of clamping process into the drape simulation
process will assist in the development of fiberglass application
in manufacturing process.
Abstract: The localized corrosion behavior of laser surface
melted 304L austenitic stainless steel was studied by
potentiodynamic polarization test. The extent of improvement in
corrosion resistance was governed by the preferred orientation and
the percentage of delta ferrite present on the surface of the laser
melted sample. It was established by orientation imaging microscopy
that the highest pitting potential value was obtained when grains were
oriented in the most close- packed [101] direction compared to the
random distribution of the base metal and other laser surface melted
samples oriented in [001] direction. The sample with lower
percentage of ferrite had good pitting resistance.
Abstract: The paper deals with calculation of the parameters of
ceramic material from a set of destruction tests of ceramic heads of
total hip joint endoprosthesis. The standard way of calculation of the
material parameters consists in carrying out a set of 3 or 4 point
bending tests of specimens cut out from parts of the ceramic material
to be analysed. In case of ceramic heads, it is not possible to cut out
specimens of required dimensions because the heads are too small (if
the cut out specimens were smaller than the normalised ones, the
material parameters derived from them would exhibit higher strength
values than those which the given ceramic material really has). On
that score, a special testing jig was made, in which 40 heads were
destructed. From the measured values of circumferential strains of the
head-s external spherical surface under destruction, the state of stress
in the head under destruction was established using the final elements
method (FEM). From the values obtained, the sought for parameters
of the ceramic material were calculated using Weibull-s weakest-link
theory.
Abstract: A mathematical model for the hydrodynamics of a
surface water treatment pilot plant was developed and validated by
the determination of the residence time distribution (RTD) for the
main equipments of the unit. The well known models of ideal/real
mixing, ideal displacement (plug flow) and (one-dimensional axial)
dispersion model were combined in order to identify the structure
that gives the best fitting of the experimental data for each equipment
of the pilot plant. RTD experimental results have shown that pilot
plant hydrodynamics can be quite well approximated by a
combination of simple mathematical models, structure which is
suitable for engineering applications. Validated hydrodynamic
models will be further used in the evaluation and selection of the
most suitable coagulation-flocculation reagents, optimum operating
conditions (injection point, reaction times, etc.), in order to improve
the quality of the drinking water.
Abstract: The experiments were performed in a batch set up
under different concentrations of Cu (II) (0.2 g.l-1 to 0.9 g.l-1), pH (4-
6), temperatures (20oC – 40oC) with varying teak leaves powder (as
biosorbent) dosage of 0.3 g.l-1 to 0.5 g.l-1. The kinetics of interactions
were tested with pseudo first order Lagergran equation and the value
for k1 was found to be 6.909 x 10-3 min-1. The biosorption data gave
a good fit with Langmuir and Fruendlich isotherms and the Langmuir
monolayer capacity (qm) was found to be 166.78 mg. g-1. Similarly
the Freundlich adsorption capacity (Kf) was estimated as 2.49 l g-1.
The mean values of the thermodynamic parameters ΔH, ΔS, and ΔG
were -62.42 KJ. mol-1, -0.219 KJ.mol-1 K-1 and -1.747 KJ.mol-1 at
293 K from a solution containing 0.4 g l-1 of Cu(II) showing the
biosorption to be thermodynamically favourable. These results show
good potentiality of using teak leaves as a biosorbent for the removal
of Cu(II) from aqueous solutions.
Abstract: This research uses computational linguistics, an area of study that employs a computer to process natural language, and aims at discerning the patterns that exist in declarative sentences used in technical texts. The approach is mathematical, and the focus is on instructional texts found on web pages. The technique developed by the author and named the MAYA Semantic Technique is used here and organized into four stages. In the first stage, the parts of speech in each sentence are identified. In the second stage, the subject of the sentence is determined. In the third stage, MAYA performs a frequency analysis on the remaining words to determine the verb and its object. In the fourth stage, MAYA does statistical analysis to determine the content of the web page. The advantage of the MAYA Semantic Technique lies in its use of mathematical principles to represent grammatical operations which assist processing and accuracy if performed on unambiguous text. The MAYA Semantic Technique is part of a proposed architecture for an entire web-based intelligent tutoring system. On a sample set of sentences, partial semantics derived using the MAYA Semantic Technique were approximately 80% accurate. The system currently processes technical text in one domain, namely Cµ programming. In this domain all the keywords and programming concepts are known and understood.
Abstract: Composite nanostructures of metal
core/semiconductor shell (Au/CdS) configuration were prepared
using organometalic method. UV-Vis spectra for the Au/CdS colloids
show initially two well separated bands, corresponding to surface
plasmon of the Au core, and the exciton of CdS shell. The absorption
of CdS shell is enhanced, while the Au plasmon band is suppressed
as the shell thickness increases. The shell sizes were estimated from
the optical spectra using the effective mass approximation model
(EMA), and compared to the sizes of the Au core and CdS shell
measured by high resolution transmission electron microscope
(HRTEM). The changes in the absorption features are discussed in
terms of gradual increase in the coupling strength of the Au core
surface plasmon and the exciton in the CdS. leading to charge
transfer and modification of electron oscillation in Au core.
Abstract: MicroRNAs are an important class of gene expression
regulators that are involved in many biological processes including
embryogenesis. miR-125b is a conserved microRNA that is enriched
in the nervous system. We have previously reported the function of
miR-125b in neuronal differentiation of human cell lines. We also
discovered the function of miR-125b in regulating p53 in human and
zebrafish. Here we further characterize the brain defects in zebrafish
embryos injected with morpholinos against miR-125b. Our data
confirm the essential role of miR-125b in brain morphogenesis
particularly in maintaining the balance between proliferation, cell
death and differentiation. We identified lunatic fringe (lfng) as an
additional target of miR-125b in human and zebrafish and suggest
that lfng may mediate the function of miR-125b in neurogenesis.
Together, this report reveals new insights into the function of miR-
125b during neural development of zebrafish.
Abstract: A sophisticated simulator provides a cost-effective measure to carry out preliminary mission testing and diagnostic while reducing potential failures for real life at sea trials. The presented simulation framework covers three key areas: AUV modeling, sensor modeling, and environment modeling. AUV modeling mainly covers the area of AUV dynamics. Sensor modeling deals with physics and mathematical models that govern each sensor installed onto the AUV. Environment model incorporates the hydrostatic, hydrodynamics, and ocean currents that will affect the AUV in a real-time mission. Based on this designed simulation framework, custom scenarios provided by the user can be modeled and its corresponding behaviors can be observed. This paper focuses on the accuracy of the simulated data from AUV model and environmental model derived from a developed AUV test-bed which was jointly upgraded by DSTO and the University of Adelaide. The main contribution of this paper is to experimentally verify the accuracy of the proposed simulation framework.
Abstract: Portuguese diet has been gradually diverging from the basic principles of healthy eating, leading to an unbalanced dietary pattern which, associated with increasing sedentary lifestyle, has a negative impact on public health. The main objective of this work was to characterize the dietary habits of university students in Viseu, Portugal. The study consisted of a sample of 80 university students, aged between 18 and 28 years. Anthropometric data (weight (kg) and height (m)) were collected and Body Mass Index (BMI) was calculated. The dietary habits were assessed through a three-day food record and the software Medpoint was used to convert food into energy and nutrients. The results showed that students present a normal body mass index. Female university students made a higher number of daily meals than male students, and these last skipped breakfast more frequently. The values of average daily intake of energy, macronutrients and calcium were higher in males. The food pattern was characterized by a predominant consumption of meat, cereal, fats and sugar. Dietary intake of dairy products, fruits, vegetables and legumes does not meet the recommendations, revealing inadequate food habits such as hypoglycemic, hyperprotein and hyperlipidemic diet. Our findings suggest that preventive interventions should be focus in promoting healthy eating habits and physical activity in adulthood.
Abstract: The evolution of information and communication
technology has made a very powerful support for the improvement of
online learning platforms in creation of courses. This paper presents a
study that attempts to explore new web architecture for creating an
adaptive online learning system to profiles of learners, using the Web
as a source for the automatic creation of courses for the online
training platform. This architecture will reduce the time and decrease
the effort performed by the drafters of the current e-learning
platform, and direct adaptation of the Web content will greatly enrich
the quality of online training courses.
Abstract: A fault detection and identification (FDI) technique is
presented to create a fault tolerant control system (FTC). The fault
detection is achieved by monitoring the position of the light source
using an array of light sensors. When a decision is made about the
presence of a fault an identification process is initiated to locate the
faulty component and reconfigure the controller signals. The signals
provided by the sensors are predictable; therefore the existence of a
fault is easily identified. Identification of the faulty sensor is based on
the dynamics of the frame. The technique is not restricted to a
particular type of controllers and the results show consistency.
Abstract: A new and cost effective robotic device was designed
for remote tele surgery using dual tone multi frequency technology
(DTMF). Tele system with Dual Tone Multiple Frequency has a large
capability in sending and receiving of data in hardware and software.
The robot consists of DC motors for arm movements and it is
controlled manually through a mobile phone through DTMF
Technology. The system enables the surgeon from base station to
send commands through mobile phone to the patient’s robotic system
which includes two robotic arms that translate the input into actual
instrument manipulation. A mobile phone attached to the
microcontroller 8051 which can activate robot through relays. The
Remote robot-assisted tele surgery eliminates geographic constraints
for getting surgical expertise where it is needed and allows an expert
surgeon to teach or proctor the performance of surgical technique by
real-time intervention.
Abstract: The thermal expansion behaviour of silicon carbide
(SCS-2) fibre reinforced 6061 aluminium matrix composite subjected
to the influenced thermal mechanical cycling (TMC) process were
investigated. The thermal stress has important effect on the
longitudinal thermal expansion coefficient of the composites. The
present paper used experimental data of the thermal expansion
behaviour of a SiC/Al composite for temperatures up to 370°C, in
which their data was used for carrying out modelling of theoretical
predictions.
Abstract: The development of the power electronics has allowed
increasing the precision and reliability of the electrical devices, thanks
to the adjustable inverters, as the Pulse Wide Modulation (PWM)
applied to the three level inverters, which is the object of this study.
The authors treat the relation between the law order adopted for a
given system and the oscillations of the electrical and mechanical
parameters of which the tolerance depends on the process with which
they are integrated (paper factory, lifting of the heavy loads,
etc.).Thus, the best choice of the regulation indexes allows us to
achieve stability and safety training without investment (management
of existing equipment). The optimal behavior of any electric device
can be achieved by the minimization of the stored electrical and
mechanical energy.
Abstract: Under the limitation of investment budget, a utility
company is required to maximize the utilization of their existing
assets during their life cycle satisfying both engineering and financial
requirements. However, utility does not have knowledge about the
status of each asset in the portfolio neither in terms of technical nor
financial values. This paper presents a knowledge based model for
the utility companies in order to make an optimal decision on power
transformer with their utilization. CommonKADS methodology, a
structured development for knowledge and expertise representation,
is utilized for designing and developing knowledge based model. A
case study of One MVA power transformer of Nepal Electricity
Authority is presented. The results show that the reusable knowledge
can be categorized, modeled and utilized within the utility company
using the proposed methodologies. Moreover, the results depict that
utility company can achieve both engineering and financial benefits
from its utilization.
Abstract: This paper presents a generalized form of the
mechanistic deconvolution technique (GMD) to modeling image sensors applicable in various pan–tilt planes of view. The mechanistic deconvolution technique (UMD) is modified with the
given angles of a pan–tilt plane of view to formulate constraint parameters and characterize distortion effects, and thereby, determine
the corrected image data. This, as a result, does not require experimental setup or calibration. Due to the mechanistic nature of
the sensor model, the necessity for the sensor image plane to be
orthogonal to its z-axis is eliminated, and it reduces the dependency on image data. An experiment was constructed to evaluate the
accuracy of a model created by GMD and its insensitivity to changes in sensor properties and in pan and tilt angles. This was compared
with a pre-calibrated model and a model created by UMD using two sensors with different specifications. It achieved similar accuracy
with one-seventh the number of iterations and attained lower mean error by a factor of 2.4 when compared to the pre-calibrated and
UMD model respectively. The model has also shown itself to be robust and, in comparison to pre-calibrated and UMD model, improved the accuracy significantly.
Abstract: In this paper two mathematical models for definition of gas accidental escape localization in the gas pipelines are suggested. The first model was created for leak localization in the horizontal branched pipeline and second one for leak detection in inclined section of the main gas pipeline. The algorithm of leak localization in the branched pipeline did not demand on knowledge of corresponding initial hydraulic parameters at entrance and ending points of each sections of pipeline. For detection of the damaged section and then leak localization in this section special functions and equations have been constructed. Some results of calculations for compound pipelines having two, four and five sections are presented. Also a method and formula for the leak localization in the simple inclined section of the main gas pipeline are suggested. Some results of numerical calculations defining localization of gas escape for the inclined pipeline are presented.