Abstract: This paper looks into detailed investigation of
thermal-hydraulic characteristics of the flow field in a fuel rod
model, especially near the spacer. The area investigate represents a
source of information on the velocity flow field, vortex, and on the
amount of heat transfer into the coolant all of which are critical for
the design and improvement of the fuel rod in nuclear power plants.
The flow field investigation uses three-dimensional Computational
Fluid Dynamics (CFD) with the Reynolds stresses turbulence model
(RSM). The fuel rod model incorporates a vertical annular channel
where three different shapes of spacers are used; each spacer shape is
addressed individually. These spacers are mutually compared in
consideration of heat transfer capabilities between the coolant and
the fuel rod model. The results are complemented with the calculated
heat transfer coefficient in the location of the spacer and along the
stainless-steel pipe.
Abstract: The RR interval series is non-stationary and unevenly
spaced in time. For estimating its power spectral density (PSD) using
traditional techniques like FFT, require resampling at uniform
intervals. The researchers have used different interpolation
techniques as resampling methods. All these resampling methods
introduce the low pass filtering effect in the power spectrum. The
lomb transform is a means of obtaining PSD estimates directly from
irregularly sampled RR interval series, thus avoiding resampling. In
this work, the superiority of Lomb transform method has been
established over FFT based approach, after applying linear and
cubicspline interpolation as resampling methods, in terms of
reproduction of exact frequency locations as well as the relative
magnitudes of each spectral component.
Abstract: The recycling of concrete, bricks and masonry rubble
as concrete aggregates is an important way to contribute to a
sustainable material flow. However, there are still various
uncertainties limiting the widespread use of Recycled Concrete
Aggregates (RCA). The fluctuations in the composition of grade
recycled aggregates and their influence on the properties of fresh and
hardened concrete are of particular concern regarding the use of
RCA. Most of problems occurring while using recycled concrete
aggregates as aggregates are due to higher porosity and hence higher
water absorption, lower mechanical strengths, residual impurities on
the surface of the RCA forming weaker bond between cement paste
and aggregate. So, the reuse of RCA is still limited. Efficient
polymer based treatment is proposed in order to reuse RCA easier.
The silicon-based polymer treatments of RCA were carried out and
were compared. This kind of treatment can improve the properties of
RCA such as the rate of water absorption on treated RCA is
significantly reduced.
Abstract: According to the statistics, the prevalence of congenital hearing loss in Taiwan is approximately six thousandths; furthermore, one thousandths of infants have severe hearing impairment. Hearing ability during infancy has significant impact in the development of children-s oral expressions, language maturity, cognitive performance, education ability and social behaviors in the future. Although most children born with hearing impairment have sensorineural hearing loss, almost every child more or less still retains some residual hearing. If provided with a hearing aid or cochlear implant (a bionic ear) timely in addition to hearing speech training, even severely hearing-impaired children can still learn to talk. On the other hand, those who failed to be diagnosed and thus unable to begin hearing and speech rehabilitations on a timely manner might lose an important opportunity to live a complete and healthy life. Eventually, the lack of hearing and speaking ability will affect the development of both mental and physical functions, intelligence, and social adaptability. Not only will this problem result in an irreparable regret to the hearing-impaired child for the life time, but also create a heavy burden for the family and society. Therefore, it is necessary to establish a set of computer-assisted predictive model that can accurately detect and help diagnose newborn hearing loss so that early interventions can be provided timely to eliminate waste of medical resources. This study uses information from the neonatal database of the case hospital as the subjects, adopting two different analysis methods of using support vector machine (SVM) for model predictions and using logistic regression to conduct factor screening prior to model predictions in SVM to examine the results. The results indicate that prediction accuracy is as high as 96.43% when the factors are screened and selected through logistic regression. Hence, the model constructed in this study will have real help in clinical diagnosis for the physicians and actually beneficial to the early interventions of newborn hearing impairment.
Abstract: The major problem that wireless communication
systems undergo is multipath fading caused by scattering of the
transmitted signal. However, we can treat multipath propagation as
multiple channels between the transmitter and receiver to improve
the signal-to-scattering-noise ratio. While using Single Input
Multiple Output (SIMO) systems, the diversity receivers extract
multiple signal branches or copies of the same signal received from
different channels and apply gain combining schemes such as Root
Mean Square Gain Combining (RMSGC). RMSGC asymptotically
yields an identical performance to that of the theoretically optimal
Maximum Ratio Combining (MRC) for values of mean Signal-to-
Noise-Ratio (SNR) above a certain threshold value without the need
for SNR estimation. This paper introduces an improvement of
RMSGC using two different issues. We found that post-detection and
de-noising the received signals improve the performance of RMSGC
and lower the threshold SNR.
Abstract: This document details the process of developing a
wireless device that captures the basic movements of the foot (plantar
flexion, dorsal flexion, abduction, adduction.), and the knee
movement (flexion). It implements a motion capture system by using
a hardware based on optical fiber sensors, due to the advantages in
terms of scope, noise immunity and speed of data transmission and
reception. The operating principle used by this system is the detection
and transmission of joint movement by mechanical elements and
their respective measurement by optical ones (in this case infrared).
Likewise, Visual Basic software is used for reception, analysis and
signal processing of data acquired by the device, generating a 3D
graphical representation in real time of each movement. The result is
a boot in charge of capturing the movement, a transmission module
(Implementing Xbee Technology) and a receiver module for
receiving information and sending it to the PC for their respective
processing.
The main idea with this device is to help on topics such as
bioengineering and medicine, by helping to improve the quality of
life and movement analysis.
Abstract: It is known that the heart interacts with and adapts to
its venous and arterial loading conditions. Various experimental
studies and modeling approaches have been developed to investigate
the underlying mechanisms. This paper presents a model of the left
ventricle derived based on nonlinear stress-length myocardial
characteristics integrated over truncated ellipsoidal geometry, and
second-order dynamic mechanism for the excitation-contraction
coupling system. The results of the model presented here describe the
effects of the viscoelastic damping element of the electromechanical
coupling system on the hemodynamic response. Different heart rates
are considered to study the pacing effects on the performance of the
left-ventricle against constant preload and afterload conditions under
various damping conditions. The results indicate that the pacing
process of the left ventricle has to take into account, among other
things, the viscoelastic damping conditions of the myofilament
excitation-contraction process.
Abstract: Building intelligent traffic guide systems has been an
interesting subject recently. A good system should be able to observe
all important visual information to be able to analyze the context of
the scene. To do so, signs in general, and traffic signs in particular,
are usually taken into account as they contain rich information to
these systems. Therefore, many researchers have put an effort on
sign recognition field. Sign localization or sign detection is the most
important step in the sign recognition process. This step filters out
non informative area in the scene, and locates candidates in later
steps. In this paper, we apply a new approach in detecting sign
locations using a new color invariant model. Experiments are carried
out with different datasets introduced in other works where authors
claimed the difficulty in detecting signs under unfavorable imaging
conditions. Our method is simple, fast and most importantly it gives
a high detection rate in locating signs.
Abstract: Retention in the IT profession is critical for
organizations to stay competitive and operate reliably in the dynamic
business environment. Most organizations rely on compensation and
rewards as primary tools to enhance retention of employees. In this
quantitative survey-based study conducted at a large global bank, we
analyze the perceptions of 575 information technology (IT) software
professionals in India and Malaysia and find that fairness of rewards
has very little impact on retention likelihood. It is far more important
to actively involve employees in organizational activities. In
addition, our findings indicate that involvement is far more important
than information flow: the typical organizational communication to
keep employees informed.
Abstract: Electrical Discharge Machine (EDM) is especially
used for the manufacturing of 3-D complex geometry and hard
material parts that are extremely difficult-to-machine by conventional
machining processes. In this paper authors review the research work
carried out in the development of die-sinking EDM within the past
decades for the improvement of machining characteristics such as
Material Removal Rate, Surface Roughness and Tool Wear Ratio. In
this review various techniques reported by EDM researchers for
improving the machining characteristics have been categorized as
process parameters optimization, multi spark technique, powder
mixed EDM, servo control system and pulse discriminating. At the
end, flexible machine controller is suggested for Die Sinking EDM to
enhance the machining characteristics and to achieve high-level
automation. Thus, die sinking EDM can be integrated with Computer
Integrated Manufacturing environment as a need of agile
manufacturing systems.
Abstract: In this paper, in order to investigate the effects of
photovoltaic system introduction to detached houses in Japan, two
kinds of works were done. Firstly, the hourly generation amount of a
4.2kW photovoltaic system were simulated in 46 cities to investigate
the potential of the system in different regions in Japan using a
simulation model of photovoltaic system. Secondly, based on the
simulated electricity generation amount, the energy saving, the
environmental and the economic effect of the photovoltaic system
were examined from hourly to annual timescales, based upon
calculations of typical electricity, heating, cooling and hot water
supply load profiles for Japanese dwellings. The above analysis was
carried out using a standard year-s hourly weather data for the
different city provided by the Expanded AMeDAS Weather Data
issued by AIJ (Architectural Institute of Japan).
Abstract: This paper applies fuzzy set theory to evaluate the
service quality of online auction. Service quality is a composition of
various criteria. Among them many intangible attributes are difficult
to measure. This characteristic introduces the obstacles for respondent
in replying to the survey. So as to overcome this problem, we
invite fuzzy set theory into the measurement of performance. By
using AHP in obtaining criteria and TOPSIS in ranking, we found
the most concerned dimension of service quality is Transaction
Safety Mechanism and the least is Charge Item. Regarding to the
most concerned attributes are information security, accuracy and
information.
Abstract: This paper presents reliability evaluation techniques
which are applied in distribution system planning studies and
operation. Reliability of distribution systems is an important issue in
power engineering for both utilities and customers. Reliability is a
key issue in the design and operation of electric power distribution
systems and load. Reliability evaluation of distribution systems has
been the subject of many recent papers and the modeling and
evaluation techniques have improved considerably.
Abstract: Fip-gts, an immunomodulatory protein purified from Ganoderma tsugae, has been reported to possess therapeutic effects in the treatment of cancer and autoimmune disease. For medicinal application, a recombinant Fip-gts was successfully expressed and purified in Sf21 insect cells by our previously work. It is important to evaluate the immunomodulatory activity of the rFip-gts. To assess the immunomodulatory potential of rFip-gts, the T lymphocytes of murine splenocytes were used in the present study. Results revealed that rFip-gts induced cellular aggregation formation. Additionally, the expression of IL-2 and IFN-r were up-regulated after the treatment of rFip-gts, and a corresponding increased production of IL-2 and IFN-r in a dose-dependent manner. The results showed that rFip-gts has an immunomodulatory activity in inducing Th1 lymphocytes from murine splenocytes released IL-2 and IFN-γ, thus suggest that rFip-gts may have therapeutic potential in vivo as an immune modulator.
Abstract: To investigate the possible correlation between peer aggression and peer victimization, 148 sixth-graders were asked to respond to the Reduced Aggression and Victimization Scales (RAVS). RAVS measures the frequency of reporting aggressive behaviors or of being victimized during the previous week prior to the survey. The scales are composed of six items each. Each point represents one instance of aggression or victimization. Specifically, the Pearson Product-Moment Correlation Coefficient (PMCC) was used to determine the correlations between the scores of the sixthgraders in the two scales, both in individual items and total scores. Positive correlations were established and correlations were significant at the 0.01 levels.
Abstract: Machining through turning was carried out in a lathe
to study the chip formation of Multiphase Ferrite
(F-B-M) microalloyed steel. Taguchi orthogonal array was employed
to perform the machining. Continuous and discontinuous chips were
formed for different cutting parameters like speed, feed and depth of
cut. Optical and scanning electron microscope was employed to
identify the chip morphology.
Abstract: In quality control of freeze-dried durian, crispiness is
a key quality index of the product. Generally, crispy testing has to be
done by a destructive method. A nondestructive testing of the
crispiness is required because the samples can be reused for other
kinds of testing. This paper proposed a crispiness classification
method of freeze-dried durians using fuzzy logic for decision
making. The physical changes of a freeze-dried durian include the
pores appearing in the images. Three physical features including (1)
the diameters of pores, (2) the ratio of the pore area and the
remaining area, and (3) the distribution of the pores are considered to
contribute to the crispiness. The fuzzy logic is applied for making the
decision. The experimental results comparing with food expert
opinion showed that the accuracy of the proposed classification
method is 83.33 percent.
Abstract: Data mining is the process of sifting through large
volumes of data, analyzing data from different perspectives and
summarizing it into useful information. One of the widely used
desktop applications for data mining is the Weka tool which is
nothing but a collection of machine learning algorithms implemented
in Java and open sourced under the General Public License (GPL). A
web service is a software system designed to support interoperable
machine to machine interaction over a network using SOAP
messages. Unlike a desktop application, a web service is easy to
upgrade, deliver and access and does not occupy any memory on the
system. Keeping in mind the advantages of a web service over a
desktop application, in this paper we are demonstrating how this Java
based desktop data mining application can be implemented as a web
service to support data mining across the internet.
Abstract: This research aims to examine the key success factors
for the diffusion of mobile entertainment services in Malaysia. The
drivers and barriers observed in this research include perceived
benefit; concerns pertaining to pricing, product and technological
standardization, privacy and security; as well as influences from
peers and community. An analysis of a Malaysian survey of 384
respondents between 18 to 25 years shows that subscribers placed
greater importance on perceived benefit of mobile entertainment
services compared to other factors. Results of the survey also show
that there are strong positive correlations between all the factors,
with pricing issue–perceived benefit showing the strongest
relationship. This paper aims to provide an extensive study on the
drivers and barriers that could be used to derive architecture for
entertainment service provision to serve as a guide for telcos to
outline suitable approaches in order to encourage mass market
adoption of mobile entertainment services in Malaysia.
Abstract: This study was conducted Ismailoglu grape type (Vitis
vinifera L.) and its vine which was aged 15 was grown on its own
root in a vegetation period of 2013 in Nevşehir province in Turkey.
In this research, it was investigated whether the applications of
Control (C), 1/3 cluster tip reduction (1/3 CTR), shoot tip reduction
(STR), 1/3 CTR + STR, TKI-HUMAS (TKI-HM) (Soil) (S), TKIHM
(Foliar) (F), TKI-HM (S + F), 1/3 CTR + TKI-HM (S), 1/3 CTR
+ TKI-HM (F), 1/3 CTR + TKI-HM (S+F), STR + TKI-HM (S), STR
+ TKI-HM (F), STR + TKI-HM (S + F), 1/3 CTR + STR+TKI-HM
(S), 1/3 CTR + STR + TKI-HM (F), 1/3 CTR + STR + TKI-HM (S +
F) on yield and yield components of Ismailoglu grape type. The
results were obtained as the highest fresh grape yield (16.15 kg/vine)
with TKI-HM (S), as the highest cluster weight (652.39 g) with 1/3
CTR + STR, as the highest 100 berry weight (419.07 g) with 1/3
CTR + STR + TKI-HM (F), as the highest maturity index (44.06)
with 1/3 CTR, as the highest must yield (810.00 ml) with STR +
TKI-HM (F), as the highest intensity of L* color (42.04) with TKIHM
(S + F), as the highest intensity of a* color (2.60) with 1/3 CTR
+ TKI-HM (S), as the highest intensity of b* color (7.16) with 1/3
CTR + TKI-HM (S) applications. To increase the fresh grape yield of
Ismailoglu grape type can be recommended TKI-HM (S) application.