Abstract: Temperature is one of the most principle factors affects aquaculture system. It can cause stress and mortality or superior environment for growth and reproduction. This paper presents the control of pond water temperature using artificial intelligence technique. The water temperature is very important parameter for shrimp growth. The required temperature for optimal growth is 34oC, if temperature increase up to 38oC it cause death of the shrimp, so it is important to control water temperature. Solar thermal water heating system is designed to supply an aquaculture pond with the required hot water in Mersa Matruh in Egypt. Neural networks are massively parallel processors that have the ability to learn patterns through a training experience. Because of this feature, they are often well suited for modeling complex and non-linear processes such as those commonly found in the heating system. Artificial neural network is proposed to control water temperature due to Artificial intelligence (AI) techniques are becoming useful as alternate approaches to conventional techniques. They have been used to solve complicated practical problems. Moreover this paper introduces a complete mathematical modeling and MATLAB SIMULINK model for the aquaculture system. The simulation results indicate that, the control unit success in keeping water temperature constant at the desired temperature by controlling the hot water flow rate.
Abstract: Riprap is mostly used to prevent erosion by flows
down the steep slopes in river engineering. A total of 53 stability tests
performed on angular riprap with a median stone size ranging from
15 to 278 mm and slope ranging from 1 to 40% are used in this study.
The existing equations for the prediction of medium size of angular
stones are checked for their accuracy using the available data.
Predictions of median size using these equations are not satisfactory
and results show deviation by more than ±20% from the observed
values. A multivariable power regression analysis is performed to
propose a new equation relating the median size with unit discharge,
bed slope, riprap thickness and coefficient of uniformity. The
proposed relationship satisfactorily predicts the median angular stone
size with ±20% error. Further, the required size of the rounded stone
is more than the angular stone for the same unit discharge and the
ratio increases with unit discharge and also with embankment slope
of the riprap.
Abstract: An optimal mean-square fusion formulas with scalar
and matrix weights are presented. The relationship between them is
established. The fusion formulas are compared on the continuous-time
filtering problem. The basic differential equation for cross-covariance
of the local errors being the key quantity for distributed fusion is
derived. It is shown that the fusion filters are effective for multi-sensor
systems containing different types of sensors. An example
demonstrating the reasonable good accuracy of the proposed filters is
given.
Abstract: This paper presents the generation of bipolar square
wave pulses with characteristics that are suitable for liquid food
sterilization using a Cascaded H-bridge Multilevel Inverter (CHMI).
Bipolar square waves pulses have been reported as stable for a
longer time during the sterilization process with minimum heat
emission and increased efficiency. The CHMI allows the system to
produce bipolar square wave pulses and yielding high output voltage
without using a transformer while fulfilling the pulse requirements
for effective liquid food sterilization. This in turn can reduce power
consumption and cost of the overall liquid food sterilization system.
The simulation results have shown that pulses with peak output
voltage of 2.4 kV, pulse width of between 1 2s and 1 ms at
frequencies of 50 Hz and 100 Hz can be generated by a 7-level
CHMI. Results from the experimental set-up based on a 5-level
CHMI has indicated the potential of the proposed circuit in
producing bipolar square wave output pulses with peak values that
depends on the DC source level supplied to the CHMI modules,
pulse width of between 12.5 2s and 1 ms at frequencies of 50 Hz
and 100 Hz.
Abstract: In the hardening energy context, the transport sector
which constitutes a large worldwide energy demand has to be
improving for decrease energy demand and global warming impacts.
In a controversial situation where subsists an increasing demand for
long-distance and high-speed travels, high-speed trains offer many
advantages, as consuming significantly less energy than road or air
transports.
At the project phase of new rail infrastructures, it is nowadays
important to characterize accurately the energy that will be induced
by its operation phase, in addition to other more classical criteria as
construction costs and travel time.
Current literature consumption models used to estimate railways
operation phase are obsolete or not enough accurate for taking into
account the newest train or railways technologies.
In this paper, an updated model of consumption for high-speed is
proposed, based on experimental data obtained from full-scale tests
performed on a new high-speed line. The assessment of the model
is achieved by identifying train parameters and measured power
consumptions for more than one hundred train routes. Perspectives
are then discussed to use this updated model for accurately assess
the energy impact of future railway infrastructures.
Abstract: The pyrolysis of hazelnut shell, polyethylene oxide and their blends were carried out catalytically at 500 and 650 ºC. Potassium dichromate was chosen according to its oxidative characteristics and decomposition temperature (500 ºC) where decomposition products are CrO3 and K2CrO4. As a main effect, a remarkable increase in gasification was observed using this catalyst for pure components and blends especially at 500 ºC rather than 650 ºC contrary to the main observation in the pyrolysis process. The increase in gas product quantity was compensated mainly with decrease in solid product and additionally in some cases liquid products.
Abstract: Cognitive Infocommunications (CogInfoCom) is a new
research direction which has emerged as the synergic convergence
of infocommunications and the cognitive sciences. In this paper,
we provide the definition of CogInfoCom, and propose an architectural
framework for the interaction-oriented design of CogInfoCom
systems. We provide the outlines of an application example of
the interaction-oriented architecture, and briefly discuss its main
characteristics.
Abstract: A property is called persistent if for any many-sorted term rewriting system , has the property if and only if term rewriting system , which results from by omitting its sort information, has the property. In this paper,we show that termination is persistent for non-overlapping term rewriting systems and we give the example as application of this result. Furthermore we obtain that completeness is persistent for non-overlapping term rewriting systems.
Abstract: The present work deals with optimization of cascade refrigeration system using eco friendly refrigerants pair R507A and R23. R507A is azeotropic mixture composed of HFC refrigerants R125/R143a (50%/50% by wt.). R23 is a single component HFC refrigerant used as replacement to CFC refrigerant R13 in low temperature applications. These refrigerants have zero ozone depletion potential and are non-flammable. Optimization of R507AR23 cascade refrigeration system performance parameters such as minimum work required, refrigeration effect, coefficient of performance and exergetic efficiency was carried out in terms of eight operating parameters- combinations using Genetic Algorithm tool. The eight operating parameters include (1) low side evaporator temperature (2) high side condenser temperature (3) temperature difference in the cascade heat exchanger (4) low side condenser temperature (5) low side degree of subcooling (6) high side degree of subcooling (7) low side degree of superheating (8) high side degree of superheating. Results show that for minimum work system should operate at high temperature in low side evaporator, low temperature in high side condenser, low temperature difference in cascade condenser, high temperature in low side condenser and low degree of subcooling and superheating in both side. For maximum refrigeration effect system should operate at high temperature in low side evaporator, high temperature in high side condenser, high temperature difference in cascade condenser, low temperature in low side condenser and higher degree of subcooling in LT and HT side. For maximum coefficient of performance and exergetic efficiency, system should operate at high temperature in low side evaporator, low temperature in high side condenser, low temperature difference in cascade condenser, high temperature in low side condenser and higher degree of subcooling and superheating in low side of the system.
Abstract: In the framework of adaptive parametric modelling of images, we propose in this paper a new technique based on the Chandrasekhar fast adaptive filter for texture characterization. An Auto-Regressive (AR) linear model of texture is obtained by scanning the image row by row and modelling this data with an adaptive Chandrasekhar linear filter. The characterization efficiency of the obtained model is compared with the model adapted with the Least Mean Square (LMS) 2-D adaptive algorithm and with the cooccurrence method features. The comparison criteria is based on the computation of a characterization degree using the ratio of "betweenclass" variances with respect to "within-class" variances of the estimated coefficients. Extensive experiments show that the coefficients estimated by the use of Chandrasekhar adaptive filter give better results in texture discrimination than those estimated by other algorithms, even in a noisy context.
Abstract: The seeds of cotton (Gossypium hirsutum) fall among the lesser known oil seeds. Cottonseeds are not normally consumed in their natural state due to their gossypol content, an antinutrient. The effect of processing on the sensory characteristics and chemical composition of cottonseed and its extract was studied by subjecting the cottonseed extract to heat treatment (boiling) and the cottonseed to fermentation. The cottonseed extract was boiled using the open pot and the pressure pot for 30 minutes respectively. The fermentation of the cottonseed was carried out for 6 days with samples withdrawn at intervals of 2 days. The extract and fermented samples were subjected to chemical analysis and sensory evaluated for colour, aroma, taste, mouth feel, appearance and overallacceptability. The open pot sample was more preferred. Fermentation for 6 days resulted into a significant reduction in gossypol level of the cottonseed; however, sample fermented for 2 days was most preferred.
Abstract: In this work the characteristics of spatial signal detec¬tion from an antenna array in various sample cases are investigated. Cases for a various number of available prior information about the received signal and the background noise are considered. The spatial difference between a signal and noise is only used. The performance characteristics and detecting curves are presented. All test-statistics are obtained on the basis of the generalized likelihood ratio (GLR). The received results are correct for a short and long sample.
Abstract: In the current work, a numerical parametric study was
performed in order to model the fluid mechanics in the riser of a
bubbling fluidized bed (BFB). The gas-solid flow was simulated by
mean of a multi-fluid Eulerian model incorporating the kinetic theory
for solid particles. The bubbling fluidized bed was simulated two
dimensionally by mean of a Computational Fluid Dynamic (CFD)
commercial software package, Fluent. The effects of using different
inter-phase drag function (the drag model of Gidaspow, Syamlal and
O-Brien and the EMMS drag model) on the model predictions were
evaluated and compared. The results showed that the drag models of
Gidaspow and Syamlal and O-Brien overestimated the drag force for
the FCC particles and predicted a greater bed expansion in
comparison to the EMMS drag model.
Abstract: Malaysia government had been trying hard in order to
find the most efficient methods in learning. However, it is hard to
actually access and evaluate students whom will then be called an
excellent student. It is because in our realties student who excellent
is only excel in academic. This evaluation becomes a problem
because it not balances in our real life interm of to get an excellent
student in whole area in their involvement of curiculum and cocuriculum.
To overcome this scenario, we designed a module for
Student Idol to evaluate student through three categories which are
academic, co-curiculum and leadership. All the categories have their
own merit point. Using this method, student will be evaluated more
accurate compared to the previously. So, teacher can easily evaluate
their student without having any emotion factor, relation factor and
others. As conclusion this system module will helps the development
of student evaluation more accurate and valid in Student Idol.
Abstract: Optimization and control of reactive power
distribution in the power systems leads to the better operation of the
reactive power resources. Reactive power control reduces
considerably the power losses and effective loads and improves the
power factor of the power systems. Another important reason of the
reactive power control is improving the voltage profile of the power
system. In this paper, voltage and reactive power control using
Neural Network techniques have been applied to the 33 shines-
Tehran Electric Company. In this suggested ANN, the voltages of PQ
shines have been considered as the input of the ANN. Also, the
generators voltages, tap transformers and shunt compensators have
been considered as the output of ANN. Results of this techniques
have been compared with the Linear Programming. Minimization of
the transmission line power losses has been considered as the
objective function of the linear programming technique. The
comparison of the results of the ANN technique with the LP shows
that the ANN technique improves the precision and reduces the
computation time. ANN technique also has a simple structure and
this causes to use the operator experience.
Abstract: Downward turbulent bubbly flows in pipes were
modeled using computational fluid dynamics tools. The
Hydrodynamics, phase distribution and turbulent structure of twophase
air-water flow in a 57.15 mm diameter and 3.06 m length
vertical pipe was modeled by using the 3-D Eulerian-Eulerian
multiphase flow approach. Void fraction, liquid velocity and
turbulent fluctuations profiles were calculated and compared against
experimental data. CFD results are in good agreement with
experimental data.
Abstract: The aim of this paper is to explain what a multienterprise tie is, what evidence its analysis provides and how does the cooperation mechanism influence the establishment of a multienterprise tie. The study focuses on businesses of smaller dimension, geographically dispersed and whose businessmen are learning to cooperate in an international environment. The empirical evidence obtained at this moment permits to conclude the following: The tie is not long-lasting, it has an end; opportunism is an opportunity to learn; the multi-enterprise tie is a space to learn about the cooperation mechanism; the local tie permits a businessman to alternate between competition and cooperation strategies; the disappearance of a tie is an experience of learning for a businessman, diminishing the possibility of failure in the next tie; the cooperation mechanism tends to eliminate hierarchical relations; the multienterprise tie diminishes the asymmetries and permits SME-s to have a better position when they negotiate with large companies; the multi-enterprise tie impacts positively on the local system. The collection of empirical evidence was done trough the following instruments: direct observation in a business encounter to which the businesses attended in 2003 (202 Mexican agro industry SME-s), a survey applied in 2004 (129), a questionnaire applied in 2005 (86 businesses), field visits to the businesses during the period 2006-2008 and; a survey applied by telephone in 2008 (55 Mexican agro industry SME-s).
Abstract: Tuberculosis (TB) is a bacterial infectious disease caused by the obligate human pathogen, Mycobacterium tuberculosis. Multidrug-resistant tuberculosis (MDR-TB) is a global reality that threatens tuberculosis control. Resistance to antibiotic Rifampicin, occurs in 95% of cases through nucleotide substitutions in an 81-bp core region of the rpoB i.e; beta subunit of DNA dependant RNA polymerase. In this paper, we studied the Rifampicin-rpoB receptor interactions In silico. First, homology modeling was performed to obtain the three dimensional structure of Mycobacterium rpoB. Sixty analogs of Rifampicin were prepared using Marvin sketch software. Both original Rifampicin and the analogs were docked with rpoB and energy values were obtained. Out of sixty analogs, 43 analogs had lesser energy values than conventional Rifampicin and hence are predicted to have greater binding affinity to rpoB. Thus, this study offers a route for the development of Rifampicin analogs against multi drug resistant Mycobacterium rpoB.
Abstract: A combined three-microphone voice activity detector (VAD) and noise-canceling system is studied to enhance speech recognition in an automobile environment. A previous experiment clearly shows the ability of the composite system to cancel a single noise source outside of a defined zone. This paper investigates the performance of the composite system when there are frequently moving noise sources (noise sources are coming from different locations but are not always presented at the same time) e.g. there is other passenger speech or speech from a radio when a desired speech is presented. To work in a frequently moving noise sources environment, whilst a three-microphone voice activity detector (VAD) detects voice from a “VAD valid zone", the 3-microphone noise canceller uses a “noise canceller valid zone" defined in freespace around the users head. Therefore, a desired voice should be in the intersection of the noise canceller valid zone and VAD valid zone. Thus all noise is suppressed outside this intersection of area. Experiments are shown for a real environment e.g. all results were recorded in a car by omni-directional electret condenser microphones.
Abstract: In this paper, we propose an easily computable proximity index for predicting voltage collapse of a load bus using only measured values of the bus voltage and power; Using these measurements a polynomial of fourth order is obtained by using LES estimation algorithms. The sum of the absolute values of the polynomial coefficient gives an idea of the critical bus. We demonstrate the applicability of our proposed method on 6 bus test system. The results obtained verify its applicability, as well as its accuracy and the simplicity. From this indicator, it is allowed to predict the voltage instability or the proximity of a collapse. Results obtained by the PV curve are compared with corresponding values by QV curves and are observed to be in close agreement.