Abstract: A bauxite ore can be utilized in Bayer Process, if the
mass ratio of Al2O3 to SiO2 is greater than 10. Otherwise, its FexOy
and SiO2 content should be removed. On the other hand, removal of
TiO2 from the bauxite ore would be beneficial because of both
lowering the red mud residue and obtaining a valuable raw material
containing TiO2 mineral. In this study, the low grade diasporic
bauxite ore of Yalvaç, Isparta, Turkey was roasted under reducing
atmosphere and subjected to magnetic separation. According to the
experimental results, 800°C for reduction temperature and 20000
Gauss of magnetic intensity were found to be the optimum
parameters for removal of iron oxide and rutile from the nonmagnetic
ore. On the other hand, 600°C and 5000 Gauss were
determined to be the optimum parameters for removal of silica from
the non-magnetic ore.
Abstract: In recent years, honeycomb fiber reinforced plastic
(FRP) sandwich panels have been increasingly used in various
industries. Low weight, low price and high mechanical strength are
the benefits of these structures. However, their mechanical properties
and behavior have not been fully explored. The objective of this
study is to conduct a combined numerical-statistical investigation of
honeycomb FRP sandwich beams subject to torsion load. In this
paper, the effect of geometric parameters of sandwich panel on
maximum shear strain in both face and core and angle of torsion in a
honeycomb FRP sandwich structures in torsion is investigated. The
effect of Parameters including core thickness, face skin thickness,
cell shape, cell size, and cell thickness on mechanical behavior of the
structure were numerically investigated. Main effects of factors were
considered in this paper and regression equations were derived.
Taguchi method was employed as experimental design and an
optimum parameter combination for the maximum structure stiffness
has been obtained. The results showed that cell size and face skin
thickness have the most significant impacts on torsion angle,
maximum shear strain in face and core.
Abstract: DNA Barcode provides good sources of needed
information to classify living species. The classification problem has
to be supported with reliable methods and algorithms. To analyze
species regions or entire genomes, it becomes necessary to use the
similarity sequence methods. A large set of sequences can be
simultaneously compared using Multiple Sequence Alignment which
is known to be NP-complete. However, all the used methods are still
computationally very expensive and require significant computational
infrastructure. Our goal is to build predictive models that are highly
accurate and interpretable. In fact, our method permits to avoid the
complex problem of form and structure in different classes of
organisms. The empirical data and their classification performances
are compared with other methods. Evenly, in this study, we present
our system which is consisted of three phases. The first one, is called
transformation, is composed of three sub steps; Electron-Ion
Interaction Pseudopotential (EIIP) for the codification of DNA
Barcodes, Fourier Transform and Power Spectrum Signal Processing.
Moreover, the second phase step is an approximation; it is
empowered by the use of Multi Library Wavelet Neural Networks
(MLWNN). Finally, the third one, is called the classification of DNA
Barcodes, is realized by applying the algorithm of hierarchical
classification.
Abstract: This paper will seek to clarify important key terms
such as home schooling and home education as well as the legalities
attached to such terms. It will reflect on the recent proposed changes
to terminology in NSW, Australia. The various pedagogical
approaches to home education will be explored including their
prominence in the Australian context. There is a strong focus on
literature from Australia. The historical background of home
education in Australia will be explained as well as the difference
between distance education and home education. The future of home
education in Australia will be discussed.
Abstract: The lifetime of a wireless sensor network can be
effectively increased by using scheduling operations. Once the
sensors are randomly deployed, the task at hand is to find the largest
number of disjoint sets of sensors such that every sensor set provides
complete coverage of the target area. At any instant, only one of these
disjoint sets is switched on, while all other are switched off. This
paper proposes a heuristic search method to find the maximum
number of disjoint sets that completely cover the region. A
population of randomly initialized members is made to explore the
solution space. A set of heuristics has been applied to guide the
members to a possible solution in their neighborhood. The heuristics
escalate the convergence of the algorithm. The best solution explored
by the population is recorded and is continuously updated. The
proposed algorithm has been tested for applications which require
sensing of multiple target points, referred to as point coverage
applications. Results show that the proposed algorithm outclasses the
existing algorithms. It always finds the optimum solution, and that
too by making fewer number of fitness function evaluations than the
existing approaches.
Abstract: Nanotechnology has become the world attention in
various applications including the solar cells devices due to the
uniqueness and benefits of achieving low cost and better
performances of devices. Recently, thin film solar cells such as
Cadmium Telluride (CdTe), Copper-Indium-Gallium-diSelenide
(CIGS), Copper-Zinc-Tin-Sulphide (CZTS), and Dye-Sensitized
Solar Cells (DSSC) enhanced by nanotechnology have attracted
much attention. Thus, a compilation of nanotechnology devices
giving the progress in the solar cells has been presented. It is much
related to nanoparticles or nanocrystallines, carbon nanotubes, and
nanowires or nanorods structures.
Abstract: In this paper, we present a new segmentation approach
for liver lesions in regions of interest within MRI (Magnetic
Resonance Imaging). This approach, based on a two-cluster Fuzzy CMeans
methodology, considers the parameter variable compactness
to handle uncertainty. Fine boundaries are detected by a local
recursive merging of ambiguous pixels with a sequential forward
floating selection with Zernike moments. The method has been tested
on both synthetic and real images. When applied on synthetic images,
the proposed approach provides good performance, segmentations
obtained are accurate, their shape is consistent with the ground truth,
and the extracted information is reliable. The results obtained on MR
images confirm such observations. Our approach allows, even for
difficult cases of MR images, to extract a segmentation with good
performance in terms of accuracy and shape, which implies that the
geometry of the tumor is preserved for further clinical activities (such
as automatic extraction of pharmaco-kinetics properties, lesion
characterization, etc.).
Abstract: These Monolayer and multilayer coatings of CrN and
AlCrN deposited on 100Cr6 (AISI 52100) substrate by PVD
magnetron sputtering system. The microstructures of the coatings
were characterized using atomic force microscopy (AFM). The AFM
analysis revealed the presence of domes and craters that are
uniformly distributed over all surfaces of the various layers.
Nanoindentation measurement of CrN coating showed maximum
hardness (H) and modulus (E) of 14 GPa and 190 GPa, respectively.
The measured H and E values of AlCrN coatings were found to be 30
GPa and 382 GPa, respectively. The improved hardness in both the
coatings was attributed mainly to a reduction in crystallite size and
decrease in surface roughness. The incorporation of Al into the CrN
coatings has improved both hardness and Young’s modulus.
Abstract: The effects of flame-holder position, the ratio of flame
holder diameter to combustion chamber diameter and injection angle
on fuel propulsive droplets sizing and effective mass fraction have
been studied by a cold flow. We named the mass of fuel vapor inside
the flammability limit as the effective mass fraction. An empty
cylinder as well as a flame-holder which are a simulator for duct
combustion has been considered. The airflow comes into the cylinder
from one side and injection operation will be done by four nozzles
which are located on the entrance of cylinder. To fulfill the
calculations a modified version of KIVA-3V code which is a
transient, three-dimensional, multiphase, multi component code for
the analysis of chemically reacting flows with sprays, is used.
Abstract: This paper is based on a large questionnaire study. The
paper presents how all participants and subgroups (upper- and
lower-level white-collar workers) answered the question, “Have you
had an ache, pain, or numbness, which you associate with desktop
computer use, in the different body parts during the last 12 months?’
14.6% of participants (19.4% of women and 8.2% of men) reported
that they had often or very often physical symptoms in the neck. Even
if our results cannot prove a causal relation of symptoms with
computer use, show that workers believe that computer use can
influence their wellbeing: this is important when devising treatment
modalities to decrease these physical symptoms.
Abstract: The purpose of the paper is to address the strategic
risk issues surrounding Hindi film distribution in Mumbai for a film
distributor, who acts as an entrepreneur when launching a product
(movie) in the market (film territory).The paper undertakes a
fundamental review of films and risk in the Hindi film industry and
applies Grounded Theory technique to understand the complex
phenomena of risk taking behavior of the film distributors (both
independent and studios) in Mumbai. Rich in-depth interviews with
distributors are coded to develop core categories through constant
comparison leading to conceptualization of the phenomena of
interest. This paper is a first-of-its-kind-attempt to understand risk
behavior of a distributor, which is akin to entrepreneurial risk
behavior under conditions of uncertainty.
Abstract: Distillery spentwash contains high chemical oxygen
demand (COD), biological oxygen demand (BOD), color, total
dissolved solids (TDS) and other contaminants even after biological
treatment. The effluent can’t be discharged as such in the surface
water bodies or land without further treatment. Reverse osmosis (RO)
treatment plants have been installed in many of the distilleries at
tertiary level in many of the distilleries in India, but are not properly
working due to fouling problem which is caused by the presence of
high concentration of organic matter and other contaminants in
biologically treated spentwash. In order to make the membrane
treatment a proven and reliable technology, proper pre-treatment is
mandatory. In the present study, ultra-filtration (UF) for pretreatment
of RO at tertiary stage has been performed. Operating
parameters namely initial pH (pHo: 2–10), trans-membrane pressure
(TMP: 4-20 bars) and temperature (T: 15-43°C) were used for
conducting experiments with UF system. Experiments were
optimized at different operating parameters in terms of COD, color,
TDS and TOC removal by using response surface methodology
(RSM) with central composite design. The results showed that
removal of COD, color and TDS was 62%, 93.5% and 75.5%
respectively, with UF, at optimized conditions with increased
permeate flux from 17.5 l/m2/h (RO) to 38 l/m2/h (UF-RO). The
performance of the RO system was greatly improved both in term of
pollutant removal as well as water recovery.
Abstract: Biodiesel production from vegetable oil will produce
glycerol as by-product about 10% of the biodiesel production. The
amount of glycerol that was produced needed alternative way to
handling immediately so as to not become the waste that polluted
environment. One of the solutions was to process glycerol to
polyglycidyl nitrate (PGN). PGN is synthesized from glycerol by
three-step reactions i.e. nitration of glycerol, cyclization of 13-
dinitroglycerine and polymerization of glycosyl nitrate. Optimum
condition of nitration of glycerol with nitric acid has not been known.
Thermodynamic feasibility should be done before run experiments in
the laboratory. The aim of this study was to determine the parameters
those affect nitration of glycerol and nitric acid and chose the
operation condition. Many parameters were simulated to verify its
possibility to experiment under conditions which would get the
highest conversion of 1, 3-dinitroglycerine and which was the ideal
condition to get it. The parameters that need to be studied to obtain
the highest conversion of 1, 3-dinitroglycerine were mol ratio of
nitric acid/glycerol, reaction temperature, mol ratio of
glycerol/dichloromethane and pressure. The highest conversion was
obtained in the range of mol ratio of nitric acid /glycerol between 2/1
– 5/1, reaction temperature of 5-25oC and pressure of 1 atm. The
parameters that need to be studied further to obtain the highest
conversion of 1.3 DNG are mol ratio of nitric acid/glycerol and
reaction temperature.
Abstract: In this study, to clarify the effectiveness of an
aluminum/chromium/tungsten-based-coated tool for cutting sintered
steel, tool wear was experimentally investigated. The sintered steel
was turned with the (Al60,Cr25,W15)N-, (Al60,Cr25,W15)(C,N)- and
(Al64,Cr28,W8)(C,N)-coated cemented carbide tools according to the
physical vapor deposition (PVD) method. Moreover, the tool wear of
the aluminum/chromium/tungsten-based-coated item was compared
with that of the (Al,Cr)N coated tool. Furthermore, to clarify the tool
wear mechanism of the aluminum/chromium/tungsten-coating film for
cutting sintered steel, Scanning Electron Microscope observation and
Energy Dispersive x-ray Spectroscopy mapping analysis were
conducted on the abraded surface. The following results were
obtained: (1) The wear progress of the (Al64,Cr28,W8)(C,N)-coated
tool was the slowest among that of the five coated tools. (2) Adding
carbon (C) to the aluminum/chromium/tungsten-based-coating film
was effective for improving the wear-resistance. (3) The main wear
mechanism of the (Al60,Cr25,W15)N-, the (Al60,Cr25,W15)(C,N)-
and the (Al64,Cr28,W8)(C,N)-coating films was abrasive wear.
Abstract: The economic use and ease of construction of profiled
deck composite slab is marred with the complex and un-economic
strength verification required for the serviceability and general safety
considerations. Beside these, albeit factors such as shear span length,
deck geometries and mechanical frictions greatly influence the
longitudinal shear strength, that determines the ultimate strength of
profiled deck composite slab, and number of methods available for its
determination; partial shear and slope-intercept are the two methods
according to Euro-code 4 provision. However, the complexity
associated with shear behavior of profiled deck composite slab, the
use of these methods in determining the load carrying capacities of
such slab yields different and conflicting values. This couple with the
time and cost constraint associated with the strength verification is a
source of concern that draws more attentions nowadays, the issue is
critical. Treating some of these known shear strength influencing
factors as random variables, the load carrying capacity violation of
profiled deck composite slab from the use of the two-methods
defined according to Euro-code 4 are determined using reliability
approach, and comparatively studied. The study reveals safety values
from the use of m-k method shows good standing compared with that
from the partial shear method.
Abstract: The aim of the present study is to detect the chaotic
behavior in monetary economic relevant dynamical system. The
study employs three different forms of Taylor rules: current, forward,
and backward looking. The result suggests the existence of the
chaotic behavior in all three systems. In addition, the results strongly
represent that using expectations in policy rule especially rational
expectation hypothesis can increase complexity of the system and
leads to more chaotic behavior.
Abstract: Bicycle Level of Service (BLOS) is a measure for
evaluating street conditions for cyclists. Currently, various methods
are proposed for BLOS. These analytical methods however have
some drawbacks: they usually assume cyclists as users that can share
street facilities with motorized vehicles, it is not easy to link them to
design process and they are not easy to follow. In addition, they only
support a narrow range of cycling facilities and may not be applicable
for all situations. Along this, the current paper introduces various
effective design factors for bicycle-friendly streets. This study
considers cyclists as users of streets who have special needs and
facilities. Therefore, the key factors that influence BLOS based on
different cycling facilities that are proposed by developed guidelines
and literature are identified. The combination of these factors
presents a complete set of effective design factors for bicycle-friendly
streets. In addition, the weight of each factor in existing BLOS
models is estimated and these effective factors are ranked based on
these weights. These factors and their weights can be used in further
studies to propose special bicycle-friendly street design model.
Abstract: The main parameters affecting the workability are the
water content, particle size, and the total surface of the grains, as long
as the mixing water begins by wetting the surface of the grains and
then fills the voids between the grains to form entrapped water, the
quantity of water remaining is called free water. The aim of this study is to undertake a fractal approach through
the relationship between the concrete formulation parameters and
workability. To develop this approach a series of concrete taken from
the literature was investigated by varying formulation parameters
such as G/S, the quantity of cement C and the quantity of water W. We also call another model as the model of water layer thickness
and model of paste layer thickness to judge their relevance, hence the
following results: the relevance of the water layer thickness model is
considered as a relevant when there is a variation in the water
quantity. The model of the paste layer thickness is only applicable if
we considered that the paste is made with the grain value Dmax =
2.85: value from which we see a stability of the model.
Abstract: We apply the non-parametric, unconditional,
hyperbolic order-α quantile estimator to appraise the relative
efficiency of Microfinance Institutions in Africa in terms of outreach.
Our purpose is to verify if these institutions, which must constantly
try to strike a compromise between their social role and financial
sustainability are operationally efficient.
Using data on African MFIs extracted from the Microfinance
Information eXchange (MIX) database and covering the 2004 to
2006 periods, we find that more efficient MFIs are also the most
profitable. This result is in line with the view that social performance
is not in contradiction with the pursuit of excellent financial
performance. Our results also show that large MFIs in terms of asset
and those charging the highest fees are not necessarily the most
efficient.
Abstract: The efficient and economic allocation of resources is
one main goal in the field of production planning and control.
Nowadays, a new variable gains in importance throughout the
planning process: Energy. Energy-efficiency has already been widely
discussed in literature, but with a strong focus on reducing the overall
amount of energy used in production. This paper provides a brief
systematic approach, how energy-supply-orientation can be used for
an energy-cost-efficient production planning and thus combining the
idea of energy-efficiency and energy-flexibility.