Abstract: In this investigation, types of commercial and special
polyacrylonitrile (PAN) fibers contain sodium 2-methyl-2-
acrylamidopropane sulfonate (SAMPS) and itaconic acid (IA)
comonomers were studied by fourier transform infrared (FT-IR)
spectroscopy. The study of FT-IR spectra of PAN fibers samples
with different comonomers shows that during stabilization of PAN
fibers, the peaks related to C≡N bonds and CH2 are reduced sharply.
These reductions are related to cyclization of nitrile groups and
stabilization procedure. This reduction in PAN fibers contain IA
comonomer is very intense in comparison with PAN fibers contain
SAMPS comonomer. This fact indicates the cycling and stabilization
for sample contain IA comonomer have been conducted more
completely. Therefore the carbon fibers produced from this material
have higher tensile strength due to suitable stabilization.
Abstract: The conjugate gradient optimization algorithm
usually used for nonlinear least squares is presented and is
combined with the modified back propagation algorithm yielding
a new fast training multilayer perceptron (MLP) algorithm
(CGFR/AG). The approaches presented in the paper consist of
three steps: (1) Modification on standard back propagation
algorithm by introducing gain variation term of the activation
function, (2) Calculating the gradient descent on error with
respect to the weights and gains values and (3) the determination
of the new search direction by exploiting the information
calculated by gradient descent in step (2) as well as the previous
search direction. The proposed method improved the training
efficiency of back propagation algorithm by adaptively modifying
the initial search direction. Performance of the proposed method
is demonstrated by comparing to the conjugate gradient algorithm
from neural network toolbox for the chosen benchmark. The
results show that the number of iterations required by the
proposed method to converge is less than 20% of what is required
by the standard conjugate gradient and neural network toolbox
algorithm.
Abstract: This paper presents the buckling analysis of short and
long functionally graded cylindrical shells under thermal and
mechanical loads. The shell properties are assumed to vary
continuously from the inner surface to the outer surface of the shell.
The equilibrium and stability equations are derived using the total
potential energy equations, Euler equations and first order shear
deformation theory assumptions. The resulting equations are solved
for simply supported boundary conditions. The critical temperature
and pressure loads are calculated for both short and long cylindrical
shells. Comparison studies show the effects of functionally graded
index, loading type and shell geometry on critical buckling loads of
short and long functionally graded cylindrical shells.
Abstract: This paper deals with the conceptual design of the
new aeroelastic demonstrator for the whirl flutter simulation. The
paper gives a theoretical background of the whirl flutter phenomenon
and describes the events of the whirl flutter occurrence in the
aerospace practice. The second part is focused on the experimental
research of the whirl flutter on aeroelastic similar models. Finally the
concept of the new aeroelastic demonstrator is described. The
demonstrator represents the wing and engine of the twin turboprop
commuter aircraft including a driven propeller. It allows the changes
of the main structural parameters influencing the whirl flutter
stability characteristics. It is intended for the experimental
investigation of the whirl flutter in the wind tunnel. The results will
be utilized for validation of analytical methods and software tools.
Abstract: This paper investigated the organizational
innovativeness of public listed housing developers in Malaysia. We
conceptualized organizational innovativeness as a multi-dimensional
construct consisting of 5 dimensions: market innovativeness, product
innovativeness, process innovativeness, behavior innovativeness and
strategic innovativeness. We carried out questionnaire survey with all
accessible public listed developers in Malaysia and received a 56
percent response. We found that the innovativeness of public listed
housing developers is low. The paper ends by providing some
explanations for the results.
Abstract: Using mini modules of Tmotes, it is possible to automate a small personal area network. This idea can be extended to large networks too by implementing multi-hop routing. Linking the various Tmotes using Programming languages like Nesc, Java and having transmitter and receiver sections, a network can be monitored. It is foreseen that, depending on the application, a long range at a low data transfer rate or average throughput may be an acceptable trade-off. To reduce the overall costs involved, an optimum number of Tmotes to be used under various conditions (Indoor/Outdoor) is to be deduced. By analyzing the data rates or throughputs at various locations of Tmotes, it is possible to deduce an optimal number of Tmotes for a specific network. This paper deals with the determination of optimum distances to reduce the cost and increase the reliability of the entire sensor network with Wireless Local Loop (WLL) capability.
Abstract: This paper begins with formal defining of human rights and freedoms, and the basic document regarding the said subject is undoubtedly French Declaration of the Rights of Man and of the Citizen from 789. This paper furthermore parses legal sources relevant for the workers' rights in legal system of the Republic of Croatia, international contracts and the Labour Act, which is also a master bill regarding workers' rights The authors are also dealing with issues of Constitutional Court of the Republic of Croatia and its' position in judicial system of the Republic of Croatia, as well as with the specifics of Constitutional Complaint, and the crucial part of the paper is based on the research conducted with an aim to determine implementation of rights and liberties guaranteed by the articles 54. and 55. of the Constitution of the Republic of Croatia by means of Constitutional Complaint.
Abstract: In present work, drying characteristics of fresh papaya (Carica papaya L.) was studied to understand the dehydration process and its behavior. Drying experiments were carried out by a laboratory scaled microwave-vacuum oven. The parameters affecting drying characteristics including operating modes (continuous, pulsed), microwave power (400 and 800 W), and vacuum pressure (20, 30, and 40 cmHg) were investigated. For pulsed mode, two levels of power-off time (60 and 120 s) were used while the power-on time was fixed at 60 s and the vacuum pressure was fixed at 40 cmHg. For both operating modes, the effects of drying conditions on drying time, drying rate, and effective diffusivity were investigated. The results showed high microwave power, high vacuum, and pulsed mode of 60 s-on/60 s-off favored drying rate as shown by the shorten drying time and increased effective diffusivity. The drying characteristics were then described by Page-s model, which showed a good agreement with experimental data.
Abstract: In this paper we present a method for gene ranking
from DNA microarray data. More precisely, we calculate the correlation
networks, which are unweighted and undirected graphs, from
microarray data of cervical cancer whereas each network represents
a tissue of a certain tumor stage and each node in the network
represents a gene. From these networks we extract one tree for
each gene by a local decomposition of the correlation network. The
interpretation of a tree is that it represents the n-nearest neighbor
genes on the n-th level of a tree, measured by the Dijkstra distance,
and, hence, gives the local embedding of a gene within the correlation
network. For the obtained trees we measure the pairwise similarity
between trees rooted by the same gene from normal to cancerous
tissues. This evaluates the modification of the tree topology due to
progression of the tumor. Finally, we rank the obtained similarity
values from all tissue comparisons and select the top ranked genes.
For these genes the local neighborhood in the correlation networks
changes most between normal and cancerous tissues. As a result
we find that the top ranked genes are candidates suspected to be
involved in tumor growth and, hence, indicates that our method
captures essential information from the underlying DNA microarray
data of cervical cancer.
Abstract: A mobile agent is a software which performs an
action autonomously and independently as a person or an
organizations assistance. Mobile agents are used for searching
information, retrieval information, filtering, intruder recognition in
networks, and so on. One of the important issues of mobile agent is
their security. It must consider different security issues in effective
and secured usage of mobile agent. One of those issues is the
integrity-s protection of mobile agents.
In this paper, the advantages and disadvantages of each method,
after reviewing the existing methods, is examined. Regarding to this
matter that each method has its own advantage or disadvantage, it
seems that by combining these methods, one can reach to a better
method for protecting the integrity of mobile agents. Therefore, this
method is provided in this paper and then is evaluated in terms of
existing method. Finally, this method is simulated and its results are
the sign of improving the possibility of integrity-s protection of
mobile agents.
Abstract: Fuel and oxidant gas delivery plate, or fuel cell
plate, is a key component of a Proton Exchange Membrane (PEM)
fuel cell. To manufacture low-cost and high performance fuel cell
plates, advanced computer modeling and finite element structure
analysis are used as virtual prototyping tools for the optimization
of the plates at the early design stage. The present study examines
thermal stress analysis of the fuel cell plates that are produced
using a patented, low-cost fuel cell plate production technique
based on screen-printing. Design optimization is applied to
minimize the maximum stress within the plate, subject to strain
constraint with both geometry and material parameters as design
variables. The study reveals the characteristics of the printed
plates, and provides guidelines for the structure and material design
of the fuel cell plate.
Abstract: All practical real-time scheduling algorithms in multiprocessor systems present a trade-off between their computational complexity and performance. In real-time systems, tasks have to be performed correctly and timely. Finding minimal schedule in multiprocessor systems with real-time constraints is shown to be NP-hard. Although some optimal algorithms have been employed in uni-processor systems, they fail when they are applied in multiprocessor systems. The practical scheduling algorithms in real-time systems have not deterministic response time. Deterministic timing behavior is an important parameter for system robustness analysis. The intrinsic uncertainty in dynamic real-time systems increases the difficulties of scheduling problem. To alleviate these difficulties, we have proposed a fuzzy scheduling approach to arrange real-time periodic and non-periodic tasks in multiprocessor systems. Static and dynamic optimal scheduling algorithms fail with non-critical overload. In contrast, our approach balances task loads of the processors successfully while consider starvation prevention and fairness which cause higher priority tasks have higher running probability. A simulation is conducted to evaluate the performance of the proposed approach. Experimental results have shown that the proposed fuzzy scheduler creates feasible schedules for homogeneous and heterogeneous tasks. It also and considers tasks priorities which cause higher system utilization and lowers deadline miss time. According to the results, it performs very close to optimal schedule of uni-processor systems.
Abstract: This paper deals with a numerical analysis of the
transient response of composite beams with strain rate dependent
mechanical properties by use of a finite difference method. The
equations of motion based on Timoshenko beam theory are derived.
The geometric nonlinearity effects are taken into account with von
Kármán large deflection theory. The finite difference method in
conjunction with Newmark average acceleration method is applied to
solve the differential equations. A modified progressive damage
model which accounts for strain rate effects is developed based on
the material property degradation rules and modified Hashin-type
failure criteria and added to the finite difference model. The
components of the model are implemented into a computer code in
Mathematica 6. Glass/epoxy laminated composite beams with
constant and strain rate dependent mechanical properties under
dynamic load are analyzed. Effects of strain rate on dynamic
response of the beam for various stacking sequences, load and
boundary conditions are investigated.
Abstract: Today we tend to go back to the past to our root
relation to nature. Therefore in search of friendly spaces there are
elements of natural environment introduced as elements of spatial
composition. Though reinvented through the use of the new
substance such as greenery, water etc. made possible by state of the
art technologies, still, in principal, they remain the same. As a result,
sustainable design, based upon the recognized means of composition
in addition to the relation of architecture and urbanism vs. nature
introduces a new aesthetical values into architectural and urban
space.
Abstract: Let k ≥ 1 and t ≥ 0 be two integers and let d = k2 + k be a positive non-square integer. In this paper, we consider the integer solutions of Pell equation x2 - dy2 = 2t. Further we derive a recurrence relation on the solutions of this equation.
Abstract: This paper presents a novel two-phase hybrid optimization algorithm with hybrid genetic operators to solve the optimal control problem of a single stage hybrid manufacturing system. The proposed hybrid real coded genetic algorithm (HRCGA) is developed in such a way that a simple real coded GA acts as a base level search, which makes a quick decision to direct the search towards the optimal region, and a local search method is next employed to do fine tuning. The hybrid genetic operators involved in the proposed algorithm improve both the quality of the solution and convergence speed. The phase–1 uses conventional real coded genetic algorithm (RCGA), while optimisation by direct search and systematic reduction of the size of search region is employed in the phase – 2. A typical numerical example of an optimal control problem with the number of jobs varying from 10 to 50 is included to illustrate the efficacy of the proposed algorithm. Several statistical analyses are done to compare the validity of the proposed algorithm with the conventional RCGA and PSO techniques. Hypothesis t – test and analysis of variance (ANOVA) test are also carried out to validate the effectiveness of the proposed algorithm. The results clearly demonstrate that the proposed algorithm not only improves the quality but also is more efficient in converging to the optimal value faster. They can outperform the conventional real coded GA (RCGA) and the efficient particle swarm optimisation (PSO) algorithm in quality of the optimal solution and also in terms of convergence to the actual optimum value.
Abstract: Heat powered solid sorption is a feasible alternative to
electrical vapor compression refrigeration systems. In this paper,
activated carbon (powder type Maxsorb and fiber type ACF-A10)-
CO2 based adsorption cooling cycles are studied using the pressuretemperature-
concentration (P-T-W) diagram. The specific cooling
effect (SCE) and the coefficient of performance (COP) of these two
cooling systems are simulated for the driving heat source
temperatures ranging from 30 ºC to 90 ºC in terms of different
cooling load temperatures with a cooling source temperature of 25
ºC. It is found from the present analysis that Maxsorb-CO2 couple
shows higher cooling capacity and COP. The maximum COPs of
Maxsorb-CO2 and ACF(A10)-CO2 based cooling systems are found
to be 0.15 and 0.083, respectively. The main innovative feature of
this cooling cycle is the ability to utilize low temperature waste heat
or solar energy using CO2 as the refrigerant, which is one of the best
alternative for applications where flammability and toxicity are not
allowed.
Abstract: Control chart pattern recognition is one of the most important tools to identify the process state in statistical process control. The abnormal process state could be classified by the recognition of unnatural patterns that arise from assignable causes. In this study, a wavelet based neural network approach is proposed for the recognition of control chart patterns that have various characteristics. The procedure of proposed control chart pattern recognizer comprises three stages. First, multi-resolution wavelet analysis is used to generate time-shape and time-frequency coefficients that have detail information about the patterns. Second, distance based features are extracted by a bi-directional Kohonen network to make reduced and robust information. Third, a back-propagation network classifier is trained by these features. The accuracy of the proposed method is shown by the performance evaluation with numerical results.
Abstract: In this research, an aerobic composting method is
studied to reuse organic waste from rubber factory waste as soil fertilizer and to study the effect of cellulolytic microbial activator
(CMA) as the activator in the rubber factory waste composting. The
performance of the composting process was monitored as a function
of carbon and organic matter decomposition rate, temperature and
moisture content. The results indicate that the rubber factory waste is best composted with water hyacinth and sludge than composted
alone. In addition, the CMA is more affective when mixed with the rubber factory waste, water hyacinth and sludge since a good fertilizer is achieved. When adding CMA into the rubber factory
waste composted alone, the finished product does not achieve a
standard of fertilizer, especially the C/N ratio.
Finally, the finished products of composting rubber factory waste and water hyacinth and sludge (both CMA and without CMA), can be an environmental friendly alternative to solve the disposal problems of rubber factory waste. Since the C/N ratio, pH, moisture
content, temperature, and nutrients of the finished products are acceptable for agriculture use.
Abstract: Centrally controlled authentication and authorization services can provide enterprise with an increase in security, more flexible access control solutions and an increased users' trust. By using redirections, users of all Web-based applications within an organization are authenticated at a single well known and secure Web site and using secure communication protocol. Users are first authenticated at the central server using their domain wide credentials before being redirected to a particular Web-based application. The central authentication server will then provide others with pertinence authorization related particulars and credentials of the authenticated user to the specific application. The trust between the clients and the server hosts is established by secure session keys exchange. Case- studies are provided to demonstrate the usefulness and flexibility of the proposed solution.