Abstract: This research aimed to modify pineapple leaf paper
(PALP) for using as wet media in the evaporation cooling system by
improving wet mechanical property (tensile strength) without
compromising water absorption property. Polyamideamineepichorohydrin
resin (PAE) and carboxymethylcellulose (CMC)
were used to strengthen the paper, and the PAE and CMC ratio of
80:20 showed the optimum wet and dry tensile index values, which
were higher than those of the commercial cooling pad (CCP).
Compared with CCP, PALP itself and all the PAE/CMC modified
PALP possessed better water absorption. The PAE/CMC modified
PALP had potential to become a new type of wet media.
Abstract: This paper aims to study decomposition behavior in
pyrolytic environment of four lignocellulosic biomass (oil palm shell,
oil palm frond, rice husk and paddy straw), and two commercial
components of biomass (pure cellulose and lignin), performed in a
thermogravimetry analyzer (TGA). The unit which consists of a
microbalance and a furnace flowed with 100 cc (STP) min-1 Nitrogen,
N2 as inert. Heating rate was set at 20⁰C min-1 and temperature
started from 50 to 900⁰C. Hydrogen gas production during the
pyrolysis was observed using Agilent Gas Chromatography Analyzer
7890A. Oil palm shell, oil palm frond, paddy straw and rice husk
were found to be reactive enough in a pyrolytic environment of up to
900°C since pyrolysis of these biomass starts at temperature as low as
200°C and maximum value of weight loss is achieved at about
500°C. Since there was not much different in the cellulose,
hemicelluloses and lignin fractions between oil palm shell, oil palm
frond, paddy straw and rice husk, the T-50 and R-50 values obtained
are almost similar. H2 productions started rapidly at this temperature
as well due to the decompositions of biomass inside the TGA.
Biomass with more lignin content such as oil palm shell was found to
have longer duration of H2 production compared to materials of high
cellulose and hemicelluloses contents.
Abstract: Leave of absence is important in maintaining a good
status of human resource quality. Allowing the employees temporarily
free from the routine assignments can vitalize the workers- morality
and productivity. This is particularly critical to secure a satisfactory
service quality for healthcare professionals of which were typically
featured with labor intensive and complicated works to perform. As
one of the veteran hospitals that were found and operated by the
Veteran Department of Taiwan, the nursing staff of the case hospital
was squeezed to an extreme minimum level under the pressure of a
tight budgeting. Leave of absence on schedule became extremely
difficult, especially for the intensive care units (ICU), in which
required close monitoring over the cared patients, and that had more
easily driven the ICU nurses nervous. Even worse, the deferred leaves
were more than 10 days at any time in the ICU because of a fluctuating
occupancy. As a result, these had brought a bad setback to this
particular nursing team, and consequently defeated the job
performance and service quality. To solve this problem and
accordingly to strengthen their morality, a project team was organized
across different departments specific for this. Sufficient information
regarding jobs and positions requirements, labor resources, and actual
working hours in detail were collected and analyzed in the team
meetings. Several alternatives were finalized. These included job
rotating, job combination, leave on impromptu and cross-departmental
redeployment. Consequently, the deferred leave days sharply reduced
70% to a level of 3 or less days. This improvement had not only
provided good shelter for the ICU nurses that improved their job
performance and patient safety but also encouraged the nurses active
participating of a project and learned the skills of solving problems
with colleagues.
Abstract: Since the beginning of human history, human
activities have caused many changes in the environment. Today, a
particular attention should be paid to gaining knowledge about water
quality of wetlands which are pristine natural environments rich in
genetic reserves. If qualitative conditions of industrial areas (in terms
of both physicochemical and biological conditions) are not addressed
properly, they could cause disruption in natural ecosystems,
especially in rivers. With regards to the quality of water resources,
determination of pollutant sources plays a pivotal role in engineering
projects as well as designing water quality control systems. Thus,
using different methods such as flow duration curves, dischargepollution
load model and frequency analysis by HYFA software
package, risk of various industrial pollutants in international and
ecologically important Gavkhoni wetland is analyzed. In this study, a
station located at Varzaneh City is used as the last station on
Zayanderud River, from where the river water is discharged into the
wetland. Results showed that elements- concentrations often
exceeded the allowed level and river water can endanger regional
ecosystem. In addition, if the river discharge is managed on Q25
basis, this basis can lower concentrations of elements, keeping them
within the normal level.
Abstract: Reinforced concrete crash barriers used in road traffic
must meet a number of criteria. Crash barriers are laid lengthwise,
one behind another, and joined using specially designed steel locks.
While developing BSV reinforced concrete crash barriers (type
ŽPSV), experiments and calculations aimed to optimize the shape of
a newly designed lock and the reinforcement quantity and
distribution in a crash barrier were carried out. The tension carrying
capacity of two parallelly joined locks was solved experimentally.
Based on the performed experiments, adjustments of nonlinear
properties of steel were performed in the calculations. The obtained
results served as a basis to optimize the lock design using a
computational model that takes into account the plastic behaviour of
steel and the influence of the surrounding concrete [6]. The response
to the vehicle impact has been analyzed using a specially elaborated
complex computational model, comprising both the nonlinear model
of the damping wall or crash barrier and the detailed model of the
vehicle [7].
Abstract: A different concept for designing and detailing of
reinforced concrete precast frame structures is analyzed in this paper.
The new detailing of the joints derives from the special hybrid
moment frame joints. The special reinforcements of this alternative
detailing, named modified special hybrid joint, are bondless with
respect to both column and beams. Full scale tests were performed on
a plan model, which represents a part of 5 story structure, cropped in
the middle of the beams and columns spans. Theoretical approach
was developed, based on testing results on twice repaired model,
subjected to lateral seismic type loading. Discussion regarding the
modified special hybrid joint behavior and further on widening
research needed concludes the presentation.
Abstract: An electric power system includes a generating, a
transmission, a distribution, and consumers subsystems. An electrical
power network in Tanzania keeps growing larger by the day and
become more complex so that, most utilities have long wished for
real-time monitoring and remote control of electrical power system
elements such as substations, intelligent devices, power lines,
capacitor banks, feeder switches, fault analyzers and other physical
facilities. In this paper, the concept of automation of management of
power systems from generation level to end user levels was
determined by using Power System Simulator for Engineering
(PSS/E) version 30.3.2.
Abstract: Color image segmentation can be considered as a
cluster procedure in feature space. k-means and its adaptive
version, i.e. competitive learning approach are powerful tools
for data clustering. But k-means and competitive learning suffer
from several drawbacks such as dead-unit problem and need to
pre-specify number of cluster. In this paper, we will explore to
use competitive and cooperative learning approach to perform
color image segmentation. In competitive and cooperative
learning approach, seed points not only compete each other, but
also the winner will dynamically select several nearest
competitors to form a cooperative team to adapt to the input
together, finally it can automatically select the correct number
of cluster and avoid the dead-units problem. Experimental
results show that CCL can obtain better segmentation result.
Abstract: This paper deals with the evaluation of flow properties
of polymeric matrix with natural animal fillers. Technical university
of Liberec cooperates on the long-term development of “green
materials“ that should replace conventionally used materials
(especially in automotive industry). Natural fibres (of animal and
plant origin) from all over the world are collected and adapted
(drying, cutting etc.) for extrusion processing. Inside the extruder
these natural additives are blended with polymeric (synthetic and
biodegradable - PLA) matrix and created compound is subsequently
cut for pellets in the wet way. These green materials with unique
recipes are then studied and their mechanical, physical and
processing properties are determined. The main goal of this research
is to develop new ecological materials very similar to unfilled
polymers. In this article the rheological behaviour of chosen natural
animal fibres is introduced considering their shape and surface that
were observed with use of SEM microscopy.
Abstract: Through a proper analysis of residual strain and stress
distributions obtained at the surface of high speed milled specimens
of AA 6082–T6 aluminium alloy, the performance of an improved
indentation method is evaluated. This method integrates a special
device of indentation to a universal measuring machine. The
mentioned device allows introducing elongated indents allowing to
diminish the absolute error of measurement. It must be noted that the
present method offers the great advantage of avoiding both the
specific equipment and highly qualified personnel, and their inherent
high costs. In this work, the cutting tool geometry and high speed
parameters are selected to introduce reduced plastic damage.
Through the variation of the depth of cut, the stability of the shapes
adopted by the residual strain and stress distributions is evaluated.
The results show that the strain and stress distributions remain
unchanged, compressive and small. Moreover, these distributions
reveal a similar asymmetry when the gradients corresponding to
conventional and climb cutting zones are compared.
Abstract: In this paper, we study the application of Extreme
Learning Machine (ELM) algorithm for single layered feedforward
neural networks to non-linear chaotic time series problems. In this
algorithm the input weights and the hidden layer bias are randomly
chosen. The ELM formulation leads to solving a system of linear
equations in terms of the unknown weights connecting the hidden
layer to the output layer. The solution of this general system of
linear equations will be obtained using Moore-Penrose generalized
pseudo inverse. For the study of the application of the method we
consider the time series generated by the Mackey Glass delay
differential equation with different time delays, Santa Fe A and
UCR heart beat rate ECG time series. For the choice of sigmoid,
sin and hardlim activation functions the optimal values for the
memory order and the number of hidden neurons which give the
best prediction performance in terms of root mean square error are
determined. It is observed that the results obtained are in close
agreement with the exact solution of the problems considered
which clearly shows that ELM is a very promising alternative
method for time series prediction.
Abstract: A major part of the flow field involves no complicated
turbulent behavior in many turbulent flows. In this research work, in
order to reduce required memory and CPU time, the flow field was
decomposed into several blocks, each block including its special
turbulence. A two dimensional backward facing step was considered
here. Four combinations of the Prandtl mixing length and standard k-
E models were implemented as well. Computer memory and CPU
time consumption in addition to numerical convergence and accuracy
of the obtained results were mainly investigated. Observations
showed that, a suitable combination of turbulence models in different
blocks led to the results with the same accuracy as the high order
turbulence model for all of the blocks, in addition to the reductions in
memory and CPU time consumption.
Abstract: In this paper, we consider nested sliding mode control of SISO nonlinear systems, perturbed by bounded matched and unmatched uncertainties. The systems are assumed to be in strict-feedback form. A step wise procedure is introduced to obtain the controller. In each step, a continuous sliding mode controller is designed as virtual control law. Then the next step sliding surface is defined by using this virtual controller. These sliding surfaces are selected as nonlinear static functions of the system states. Finally in the last step, smooth static state feedback control law is determined such that the output reaches the desired set-point while the system is forced arbitrary close to the intersection of sliding surfaces and the states remain bounded.
Abstract: This research aimed to study on the potential of
recycling organic waste in Suan Sunandha Rajabhat University as
compost. In doing so, the composition of solid waste generated in the
campus was investigated while physical and chemical properties of
organic waste were analyzed in order to evaluate the portion of waste
suitable for recycling as compost. As a result of the study, it was
found that (1) the amount of organic waste was averaged at 299.8
kg/day in which mixed food wastes had the highest amount of 191.9
kg/day followed by mixed leave & yard wastes and mixed fruit &
vegetable wastes at the amount of 66.3 and 41.6 kg/day respectively;
(2) physical and chemical properties of organic waste in terms of
moisture content was between 69.54 to 78.15%, major elements for
plant as N, P and K were 0.14 to 0.17%, 0.46 to 0.52% and 0.16 to
0.18% respectively, and carbon/nitrogen ratio (C/N) was about 15:1
to 17.5:1; (3) recycling organic waste as compost was designed by
aerobic decomposition using mixed food wastes : mixed leave & yard
wastes : mixed fruit & vegetable wastes at the portion of 3:2:1 by
weight in accordance with the potential of their amounts and their
physical and chemical properties.
Abstract: The study of piezoelectric material in the past was in
T-Domain form; however, no one has studied piezoelectric material in the S-Domain form. This paper will present the piezoelectric material in the transfer function or S-Domain model. S-Domain is a
well known mathematical model, used for analyzing the stability of the material and determining the stability limits. By using S-Domain
in testing stability of piezoelectric material, it will provide a new tool for the scientific world to study this material in various forms.
Abstract: Organochlorine pesticides (OCPs) are known to be
persistent and bioaccumulative toxicants that may cause reproductive
impairments in wildlife as well as human. The current study uses the
snail-eating turtle Malayemys macrocephala, a long-lived animal
commonly distribute in rice field habitat in central part of Thailand,
as a sentinel to monitor OCP contamination in environment. The
nest soil, complete clutch of eggs, and blood of the turtle were
collected from agricultural areas in the Chao Phraya River Basin,
Thailand during the nesting season of 2007-2008. The novel
methods for tissue extraction by an accelerated solvent extractor
(ASE, for egg) and liquid-liquid extraction (for blood) have been
developed. The nineteen OCP residues were analyzed by gas
chromatography with micro-electron captured detector (GC-μECD).
The validated methods have met requirements of the AOAC
standard. The results indicated that significant amounts of OCPs are
still contaminated in nest soil and eggs of the turtle even though the
OCPs had been banned in this area for many years. This suggested
the potential risk to health of wildlife as well as human in the area.
Abstract: In this paper we discuss a set of guidelines which
could be adapted when designing an audio user interface for the
visually impaired. It is based on an audio environment that is
focused on audio positioning. Unlike current applications which only
interpret Graphical User Interface (GUI) for the visually impaired,
this particular audio environment bypasses GUI to provide a direct
auditory output. It presents the capability of two dimensional (2D)
navigation on audio interfaces. This paper highlights the significance
of a 2D audio environment with spatial information in the context
of the visually impaired. A thorough usability study has been conducted
to prove the applicability of proposed design guidelines for
these auditory interfaces. While proving these guidelines, previously
unearthed design aspects have been revealed in this study.
Abstract: This paper deals with the problem of thermal and
mechanical shocks, which rising during operation, mostly at
interrupted cut. Here will be solved their impact on the cutting edge
tool life, the impact of coating technology on resistance to shocks
and experimental determination of tool life in heating flame.
Resistance of removable cutting edges against thermal and
mechanical shock is an important indicator of quality as well as its
abrasion resistance. Breach of the edge or its crumble may occur due
to cyclic loading. We can observe it not only during the interrupted
cutting (milling, turning areas abandoned hole or slot), but also in
continuous cutting. This is due to the volatility of cutting force on
cutting. Frequency of the volatility in this case depends on the type
of rising chips (chip size element). For difficult-to-machine materials
such as austenitic steel particularly happened at higher cutting speeds
for the localization of plastic deformation in the shear plane and for
the inception of separate elements substantially continuous chips.
This leads to variations of cutting forces substantially greater than for
other types of steel.
Abstract: This paper introduces a framework that aims to
support the design and development of mobile services. The
traditional innovation process and its supporting instruments in form
of creativity tools, acceptance research and user-generated content
analysis are screened for potentials for improvement. The result is a
reshaped innovation process where acceptance research and usergenerated
content analysis are fully integrated within a creativity
tool. Advantages of this method are the enhancement of design
relevant information for developers and designers and the possibility
to forecast market success.
Abstract: The current trend of increasing quality and demands
of the final product is affected by time analysis of the entire
manufacturing process. The primary requirement of manufacturing is
to produce as many products as soon as possible, at the lowest
possible cost, but of course with the highest quality. Such
requirements may be satisfied only if all the elements entering and
affecting the production cycle are in a fully functional condition.
These elements consist of sensory equipment and intelligent control
elements that are essential for building intelligent manufacturing
systems. The intelligent manufacturing paradigm includes a new
approach to production system structure design. Intelligent behaviors
are based on the monitoring of important parameters of system and
its environment. The flexible reaction to changes. The realization and
utilization of this design paradigm as an "intelligent manufacturing
system" enables the flexible system reaction to production
requirement as soon as environmental changes too. Results of these
flexible reactions are a smaller layout space, be decreasing of
production and investment costs and be increasing of productivity.
Intelligent manufacturing system itself should be a system that can
flexibly respond to changes in entering and exiting the process in
interaction with the surroundings.