Abstract: In this paper a special kind of buffer management policy is studied where the packet are preempted even when sufficient space is available in the buffer for incoming packets. This is done to congestion for future incoming packets to improve QoS for certain type of packets. This type of study has been done in past for ATM type of scenario. We extend the same for heterogeneous traffic where data rate and size of the packets are very versatile in nature. Typical example of this scenario is the buffer management in Differentiated Service Router. There are two aspects that are of interest. First is the packet size: whether all packets have same or different sizes. Second aspect is the value or space priority of the packets, do all packets have the same space priority or different packets have different space priorities. We present two types of policies to achieve QoS goals for packets with different priorities: the push out scheme and the expelling scheme. For this work the scenario of packets of variable length is considered with two space priorities and main goal is to minimize the total weighted packet loss. Simulation and analytical studies show that, expelling policies can outperform the push out policies when it comes to offering variable QoS for packets of two different priorities and expelling policies also help improve the amount of admissible load. Some other comparisons of push out and expelling policies are also presented using simulations.
Abstract: The aim of a biological model is to understand the
integrated structure and behavior of complex biological systems as a
function of the underlying molecular networks to achieve simulation
and forecast of their operation. Although several approaches have
been introduced to take into account structural and environment
related features, relatively little attention has been given to represent
the behavior of biological systems. The Abstract Biological Process
(ABP) model illustrated in this paper is an object-oriented model
based on UML (the standard object-oriented language). Its main
objective is to bring into focus the functional aspects of the
biological system under analysis.
Abstract: This paper focuses on a critical component of the situational awareness (SA), the neural control of autonomous constant depth flight of an autonomous underwater vehicle (AUV). Autonomous constant depth flight is a challenging but important task for AUVs to achieve high level of autonomy under adverse conditions. The fundamental requirement for constant depth flight is the knowledge of the depth, and a properly designed controller to govern the process. The AUV, named VORAM, is used as a model for the verification of the proposed hybrid control algorithm. Three neural network controllers, named NARMA-L2 controllers, are designed for fast and stable diving maneuvers of chosen AUV model. This hybrid control strategy for chosen AUV model has been verified by simulation of diving maneuvers using software package Simulink and demonstrated good performance for fast SA in real-time searchand- rescue operations.
Abstract: Point quad tree is considered as one of the most
common data organizations to deal with spatial data & can be used to
increase the efficiency for searching the point features. As the
efficiency of the searching technique depends on the height of the
tree, arbitrary insertion of the point features may make the tree
unbalanced and lead to higher time of searching. This paper attempts
to design an algorithm to make a nearly balanced quad tree. Point
pattern analysis technique has been applied for this purpose which
shows a significant enhancement of the performance and the results
are also included in the paper for the sake of completeness.
Abstract: Production of biogas from bakery waste was enhanced
by additional bacterial cell. This study was divided into 2 steps. First
step, grease waste from bakery industry-s grease trap was initially
degraded by Pseudomonas aeruginosa. The concentration of byproduct,
especially glycerol, was determined and found that glycerol
concentration increased from 12.83% to 48.10%. Secondary step, 3
biodigesters were set up in 3 different substrates: non-degraded waste
as substrate in first biodigester, degraded waste as substrate in
secondary biodigester, and degraded waste mixed with swine manure
in ratio 1:1 as substrate in third biodigester. The highest
concentration of biogas was found in third biodigester that was
44.33% of methane and 63.71% of carbon dioxide. The lower
concentration at 24.90% of methane and 18.98% of carbon dioxide
was exhibited in secondary biodigester whereas the lowest was found
in non-degraded waste biodigester. It was demonstrated that the
biogas production was greatly increased with the initial grease waste
degradation by Pseudomonas aeruginosa.
Abstract: Active network was developed to solve the problem of
the current sharing-based network–difficulty in applying new
technology, service or standard, and duplicated operation at several
protocol layers. Active network can transport the packet loaded with
the executable codes, which enables to change the state of the network
node. However, if the network node is placed in the sharing-based
network, security and safety issues should be resolved. To satisfy this
requirement, various security aspects are required such as
authentication, authorization, confidentiality and integrity. Among
these security components, the core factor is the encryption key. As a
result, this study is designed to propose the scheme that manages the
encryption key, which is used to provide security of the
comprehensive active directory, based on the domain.
Abstract: In this paper, the babbitting of a bearing in boiler feed pump of an electromotor has been studied. These bearings have an important role in reducing the shut down times in the pumps, compressors and turbines. The most conventional method in babbitting is casting as a melting method. The comparison between thermal spray and casting methods in babbitting shows that the thermal spraying babbitt layer has better performance and tribological behavior. The metallurgical and tribological analysis such as SEM, EDS and wet chemical analysis has been made in the Babbitt alloys and worn surfaces. Two type of babbitt materials: tinbase and lead-base babbitt was used. The benefits of thermally sprayed babbitt layers are completely clear especially in large bearings.
Abstract: Titanium dioxide coatings were deposited by utilizing
atmospheric plasma spraying (APS) system. The agglomerated nanopowder
and different spraying parameters were used to determine
their influences on the microstructure surface feature and photoabsorption
of the coatings. The microstructure of as-sprayed TiO2
coatings were characterized by scanning electron microscope (SEM).
Surface characteristics were investigated by Fourier Transform
Infrared (FT-IR). The photo absorption was determined by UV-VIS
spectrophotometer. It is found that the spray parameters have an
influence on the microstructure, surface feature and photo-absorption
of the TiO2 coatings.
Abstract: It-s known that incorporating prior knowledge into support
vector regression (SVR) can help to improve the approximation
performance. Most of researches are concerned with the incorporation
of knowledge in form of numerical relationships. Little work,
however, has been done to incorporate the prior knowledge on the
structural relationships among the variables (referred as to Structural
Prior Knowledge, SPK). This paper explores the incorporation of SPK
in SVR by constructing appropriate admissible support vector kernel
(SV kernel) based on the properties of reproducing kernel (R.K).
Three-levels specifications of SPK are studies with the corresponding
sub-levels of prior knowledge that can be considered for the method.
These include Hierarchical SPK (HSPK), Interactional SPK (ISPK)
consisting of independence, global and local interaction, Functional
SPK (FSPK) composed of exterior-FSPK and interior-FSPK. A
convenient tool for describing the SPK, namely Description Matrix
of SPK is introduced. Subsequently, a new SVR, namely Motivated
Support Vector Regression (MSVR) whose structure is motivated
in part by SPK, is proposed. Synthetic examples show that it is
possible to incorporate a wide variety of SPK and helpful to improve
the approximation performance in complex cases. The benefits of
MSVR are finally shown on a real-life military application, Air-toground
battle simulation, which shows great potential for MSVR to
the complex military applications.
Abstract: A lightpipe is an about 99 percent specular reflective
mirror pipe or duct that is used for the transmission of the daylight
from the outside into a building. The lightpipes are usually used in
the daylighting buildings, in the residential, industrial and
commercial sectors. This paper is about the performances of a
lightpipe installed in a laboratory (3 m x 2.6 m x 3 m) without
windows. The aim is to analyse the luminous intensity distribution
for several sky/sun conditions. The lightpipe was monitored during
the year 2006. The lightpipe is 1 m long and the diameter of the top
collector and of the internal diffuser device is 0.25 m. In the
laboratory there are seven illuminance sensors: one external is
located on the roof of the laboratory and six internal sensors are
connected to a data acquisition system. The internal sensors are
positioned under the internal diffusive device at an height of 0.85 m
from the floor to simulate a working plane. The numerical data are
obtained through a simulation software. This paper shows the
comparison between the experimental and numerical results
concerning the behavior of the lightpipe.
Abstract: This research is to study the performance of heat
pump dryer for drying of kaffir lime leaves under different media and
to compare the color values and essential oil content of final products
after drying. In the experiments, kaffir lime leaves were dried in the
closed-loop system at drying temperatures of 40, 50 and 60 oC. The
drying media used in this study were hot air, CO2 and N2 gases. The
velocity of drying media in the drying chamber was 0.4 m/s with
bypass ratio of 30%. The initial moisture content of kaffir lime leaves
was approximately 180-190 % d.b. It was dried until down to a final
moisture content of 10% d.b. From the experiments, the results
showed that drying rate, the coefficient of performance (COP) and
specific energy consumption (SEC) depended on drying temperature.
While drying media did not affect on drying rate. The time for kaffir
lime leaves drying at 40, 50 and 60 oC was 10, 5 and 3 hours,
respectively. The performance of the heat pump system decreased
with drying temperature in the range of 2.20-3.51. In the aspect of
final product color, the greenness and overall color had a great
change under drying temperature at 60 oC rather than drying at 40
and 50 oC. When compared among drying media, the greenness and
overall color of product dried with hot air at 60 oC had a great change
rather than dried with CO2 and N2.
Abstract: This paper presents unified theory for local (Savitzky-
Golay) and global polynomial smoothing. The algebraic framework
can represent any polynomial approximation and is seamless from
low degree local, to high degree global approximations. The representation
of the smoothing operator as a projection onto orthonormal
basis functions enables the computation of: the covariance matrix
for noise propagation through the filter; the noise gain and; the
frequency response of the polynomial filters. A virtually perfect Gram
polynomial basis is synthesized, whereby polynomials of degree
d = 1000 can be synthesized without significant errors. The perfect
basis ensures that the filters are strictly polynomial preserving. Given
n points and a support length ls = 2m + 1 then the smoothing
operator is strictly linear phase for the points xi, i = m+1. . . n-m.
The method is demonstrated on geometric surfaces data lying on an
invariant 2D lattice.
Abstract: Summarizing skills have been introduced to English
syllabus in secondary school in Malaysia to evaluate student-s comprehension for a given text where it requires students to employ several strategies to produce the summary. This paper reports on our effort to develop a computer-based summarization assessment system
that detects the strategies used by the students in producing their
summaries. Sentence decomposition of expert-written summaries is
used to analyze how experts produce their summary sentences. From
the analysis, we identified seven summarizing strategies and their
rules which are then transformed into a set of heuristic rules on how
to determine the summarizing strategies. We developed an algorithm
based on the heuristic rules and performed some experiments to
evaluate and support the technique proposed.
Abstract: The gel-supported precipitation (GSP) process can be
used to make spherical particles (spherules) of nuclear fuel,
particularly for very high temperature reactors (VHTR) and even for
implementing the process called SPHEREPAC. In these different
cases, the main characteristics are the sphericity of the particles to be
manufactured and the control over their grain size. Nonetheless,
depending on the specifications defined for these spherical particles,
the GSP process has intrinsic limits, particularly when fabricating
very small particles. This paper describes the use of secondary
fragmentation (water, water/PVA and uranyl nitrate) on solid
surfaces under varying temperature and vibration conditions to assess
the relevance of using this new technique to manufacture very small
spherical particles by means of a modified GSP process. The
fragmentation mechanisms are monitored and analysed, before the
trends for its subsequent optimised application are described.
Abstract: Most of the biclustering/projected clustering algorithms are based either on the Euclidean distance or correlation coefficient which capture only linear relationships. However, in many applications, like gene expression data and word-document data, non linear relationships may exist between the objects. Mutual Information between two variables provides a more general criterion to investigate dependencies amongst variables. In this paper, we improve upon our previous algorithm that uses mutual information for biclustering in terms of computation time and also the type of clusters identified. The algorithm is able to find biclusters with mixed relationships and is faster than the previous one. To the best of our knowledge, none of the other existing algorithms for biclustering have used mutual information as a similarity measure. We present the experimental results on synthetic data as well as on the yeast expression data. Biclusters on the yeast data were found to be biologically and statistically significant using GO Tool Box and FuncAssociate.
Abstract: We propose an integral tracking control method for a piezoelectric actuator system. The proposed method achieves the output tracking without requiring any hysteresis observer or schemes to compensate the hysteresis effect. With the proposed control law, the system is converted into the standard singularly perturbed model. Using Tikhonov-s theorem, we guarantee that the tracking error can be reduced to arbitrarily small bound. A numerical example is given to illustrate the effectiveness of our proposed method.
Abstract: The major focus of this work was to characterize hydrodynamics in a packed-bed with and without static mixer by using Computational Fluid Dynamic (CFD). The commercial software: COMSOL MULTIPHYSICSTM Version 3.3 was used to simulate flow fields of mixed-gas reactants i.e. CO and H2. The packed-bed was a single tube with the inside diameter of 0.8 cm and the length of 1.2 cm. The static mixer was inserted inside the tube. The number of twisting elements was 1 with 0.8 cm in diameter and 1.2 cm in length. The packed-bed with and without static mixer were both packed with approximately 700 spherical structures representing catalyst pellets. Incompressible Navier-Stokes equations were used to model the gas flow inside the beds at steady state condition, in which the inlet Reynolds Number (Re) was 2.31. The results revealed that, with the insertion of static mixer, the gas was forced to flow radially inward and outward between the central portion of the tube and the tube wall. This could help improving the overall performance of the packed-bed, which could be utilized for heterogeneous catalytic reaction such as reforming and Fischer- Tropsch reactions.
Abstract: A DC-to-DC converter for applications involving a
source with widely varying voltage conditions with loads requiring
constant voltage from full load down to no load is presented.
The switching regulator considered is a Buck converter with Pulse
Skipping Modulation control whereby pulses applied to the switch
are blocked or released on output voltage crossing a predetermined
value. Results of the study on the performance of regulator circuit
are presented. The regulator regulates over a wide input voltage range
with slightly higher ripple content and good transient response. Input
current spectrum indicates a good EMI performance with crowding
of components at low frequency range.
Abstract: Sinc-collocation scheme is one of the new techniques
used in solving numerical problems involving integral equations. This
method has been shown to be a powerful numerical tool for finding
fast and accurate solutions. So, in this paper, some properties of the
Sinc-collocation method required for our subsequent development
are given and are utilized to reduce integral equation of the first
kind to some algebraic equations. Then convergence with exponential
rate is proved by a theorem to guarantee applicability of numerical
technique. Finally, numerical examples are included to demonstrate
the validity and applicability of the technique.
Abstract: Calcium [Ca2+] dynamics is studied as a potential form
of neuron excitability that can control many irregular processes like
metabolism, secretion etc. Ca2+ ion enters presynaptic terminal and
increases the synaptic strength and thus triggers the neurotransmitter
release. The modeling and analysis of calcium dynamics in neuron
cell becomes necessary for deeper understanding of the processes
involved. A mathematical model has been developed for cylindrical
shaped neuron cell by incorporating physiological parameters like
buffer, diffusion coefficient, and association rate. Appropriate initial
and boundary conditions have been framed. The closed form solution
has been developed in terms of modified Bessel function. A computer
program has been developed in MATLAB 7.11 for the whole
approach.