Abstract: The effect of transition metal doping on Pt/Al2O3
catalyst used in propane dehydrogenation reaction at 500°C was
studied. The preparation methods investigated were sequential
impregnation (Pt followed by the 2nd metal or the 2nd metal followed
by Pt) and co-impregnation. The metal contents of these catalysts
were fixed as the weight ratio of Pt per the 2nd metal of around 0.075.
These catalysts were characterized by N2-physisorption, TPR, COchemisorption
and NH3-TPD. It was found that the impregnated 2nd
metal had an effect upon reducibility of Pt due to its interaction with
transition metal-containing structure. This was in agreement with the
CO-chemisorption result that the presence of Pt metal, which is a
result from Pt species reduction, was decreased. The total acidity of
bimetallic catalysts is decreased but the strong acidity is slightly
increased. It was found that the stability of bimetallic catalysts
prepared by co-impregnation and sequential impregnation where the
2nd metal was impregnated before Pt were better than that of
monometallic catalyst (undoped Pt one) due to the forming of Pt sites
located on the transition metal-oxide modified surface. Among all
preparation methods, the sequential impregnation method- having Pt
impregnated before the 2nd metal gave the worst stability because this
catalyst lacked the modified Pt sites and some fraction of Pt sites was
covered by the 2nd metal.
Abstract: Robotics brings together several very different
engineering areas and skills. There are various types of robot such as
humanoid robot, mobile robots, remotely operated vehicles, modern
autonomous robots etc. This survey paper advocates the operation of a
robotic car (remotely operated vehicle) that is controlled by a mobile
phone (communicate on a large scale over a large distance even from
different cities). The person makes a call to the mobile phone placed
in the car. In the case of a call, if any one of the button is pressed, a
tone equivalent to the button pressed is heard at the other end of the
call. This tone is known as DTMF (Dual Tone Multiple Frequency).
The car recognizes this DTMF tone with the help of the phone stacked
in the car. The received tone is processed by the Arduino
microcontroller. The microcontroller is programmed to acquire a
decision for any given input and outputs its decision to motor drivers
in order to drive the motors in the forward direction or backward
direction or left or right direction. The mobile phone that makes a call
to cell phone stacked in the car act as a remote.
Abstract: This technical contribution treats of a novel approach
to condition-oriented maintenance as elaborated by Collaborative
Research Centre 653 at the Leibniz University in Hanover. The
objective resides in the targeted analysis of information about a
component's lifecycle for maintenance purposes. The information in
question is collected by means of the Collaborative Research Centre's
innovative technologies. This enables preventive maintenance of
components on the basis of their condition. This contribution initially
explains condition-oriented maintenance, before introducing the
Collaborative Research Centre and finally presenting the
methodology for analyzing the information. The current state of
development is described and an outlook provided for expanding the
methodology.
Abstract: To study the effect of the cross direction in bead
wheat, three hybrid combinations (Babyle 113, Iratome), (Sawa,
Tamose2) and (Al Hashymya, Al Iraq) were tested for plant height,
spike and awn length, number of grains per spike, 1000-grain weight,
number of tillers/m and grain yield. The results revealed that the
direction of the crosses significantly effect on the number of
grains/spike, number of tillers/m and grain yields. Grain yield was
positively and significantly correlated with 1000-grain weight,
number of grains per spike and tillers. Depend on the results of
heritability and genetic advance it was suggested that 1000-grain
weight, number of grains per spike and tillers should be given
emphasis for future wheat yield improvement programs.
Abstract: Information technology and information systems are
currently at a tipping point. The digital age fundamentally transforms
a large number of industries in the ways they work. Lines between
business and technology blur. Researchers have acknowledged that
this is the time in which the IT/IS organisation needs to re-strategize
itself. In this paper, the author provides a structured review of the IS
and organisation design literature addressing the question of how the
digital age changes the design categories of an IT/IS organisation
design. The findings show that most papers just analyse single
aspects of either IT/IS relevant information or generic organisation
design elements but miss a holistic ‘big-picture’ onto an IT/IS
organisation design. This paper creates a holistic IT/IS organisation
design framework bringing together the IS research strand, the digital
strand and the generic organisation design strand. The research
identified four IT/IS organisation design categories (strategy,
structure, processes and people) and discusses the importance of two
additional categories (sourcing and governance). The authors findings
point to a first anchor point from which further research needs to be
conducted to develop a holistic IT/IS organisation design framework.
Abstract: Paraffinic oils were submitted to microbial action. The
microorganisms consisted of bacteria of the genera Pseudomonas sp.
and Bacillus lincheniforms. The alterations in interfacial tension were
determined using a tensometer and applying the hanging drop
technique at room temperature (299 K ±275 K). The alteration in the
constitution of the paraffins was evaluated by means of gas
chromatography. The microbial activity was observed to reduce
interfacial tension by 54 to 78%, as well as consuming the paraffins
C19 to C29 and producing paraffins C36 to C44. The LIFirr technique
made it possible to determine the microbial action quickly.
Abstract: If teamwork is the key to organizational learning,
productivity and growth, then, why do some teams succeed in
achieving these, while others falter at different stages? Building
teams in higher education institutions has been a challenge and an
open-ended constructivist approach was considered on an
experimental basis for this study to address this challenge. For this
research, teams of students from the MBA program were chosen to
study the effect of teamwork in learning, the motivation levels among
student team members, and the effect of collaboration in achieving
team goals. The teams were built on shared vision and goals,
cohesion was ensured, positive induction in the form of faculty
mentoring was provided for each participating team and the results
have been presented with conclusions and suggestions.
Abstract: Data mining idea is mounting rapidly in admiration
and also in their popularity. The foremost aspire of data mining
method is to extract data from a huge data set into several forms that
could be comprehended for additional use. The data mining is a
technology that contains with rich potential resources which could be
supportive for industries and businesses that pay attention to collect
the necessary information of the data to discover their customer’s
performances. For extracting data there are several methods are
available such as Classification, Clustering, Association,
Discovering, and Visualization… etc., which has its individual and
diverse algorithms towards the effort to fit an appropriate model to
the data. STATISTICA mostly deals with excessive groups of data
that imposes vast rigorous computational constraints. These results
trials challenge cause the emergence of powerful STATISTICA Data
Mining technologies. In this survey an overview of the STATISTICA
software is illustrated along with their significant features.
Abstract: Degradation of agricultural soils has increased rapidly
during the last 20 years due to the indiscriminate use of pesticides
and other anthropogenic activities. Currently, there is an urgent need
of soil restoration to increase agricultural production. Utilization of
sewage sludge or municipal solid waste is an important way to
recycle nutrient elements and improve soil quality. With these
amendments, nutrient availability in the aqueous phase might be
increased and production of healthier crops can be accomplished.
This research project aimed to achieve sustainable management of
tropical agricultural soils, specifically in Puerto Rico, through the
amendment of water treatment plant sludge’s. This practice avoids
landfill disposal of sewage sludge and at the same time results costeffective
practice for recycling solid waste residues. Coriander
sativum was cultivated in a compost-soil-sludge mixture at different
proportions. Results showed that Coriander grown in a mixture of
25% compost+50% Voladora soi+25% sludge had the best growth
and development. High chlorophyll content (33.01 ± 0.8) was
observed in Coriander plants cultivated in 25% compost+62.5%
Coloso soil+ 12.5% sludge compared to plants grown with no sludge
(32.59 ± 0.7). ICP-OES analysis showed variations in mineral
element contents (macro and micronutrients) in coriander plant
grown I soil amended with sludge and compost.
Abstract: The paper tackles the topic of determining the cost of
innovation in software development projects. Innovation can be
achieved either in a planned or unplanned manner. The paper
approaches the scenarios were innovation is planned for. As a starting
point an innovative software development project is analyzed. The
project is depicted step by step as it was implemented, from inception
to delivery. Costs that are proprietary to innovation in software
development are isolated based on the author’s personal experience
in managing the above mentioned project. Innovation costs
components identified by the author are then validated using open
discussions with software development professionals and projects
managers on LinkedIn groups. In order to receive relevant feedback
only groups that focus on software development and innovation
management are targeted. Additional innovation cost components
suggested by software development professionals and projects
managers are also considered. Based on the identified cost
components an indicator is built. The indicator is meant to formalize
the process of determining the cost of innovation in a software
development project. The indicator aggregates all the innovation cost
components that are identified in the research process. The process of
calculating each cost component is also described. Conclusions are
formulated and new related research topics are submitted for debate.
Abstract: Properties of Portland cement mixtures with various
fractions of metakaolin were studied. 10% of Portland cement CEM I
42.5 R was replaced by different fractions of high reactivity
metakaolin with defined chemical and mineralogical properties.
Various fractions of metakaolin were prepared by jet mill classifying
system. There is a clear trend between fineness of metakaolin and
hydration heat development. Due to metakaolin presence in mixtures
the compressive strength development of mortars is rather slower for
coarser fractions but 28-day flexural strengths are improved for all
fractions of metakaoline used in mixtures compared to reference
sample of pure Portland cement. Yield point, plastic viscosity and
adhesion of fresh pastes are considerably influenced by fineness of
metakaolin used in cement pastes.
Abstract: The paper presents a thermodynamic cycle analysis
for three turboshaft engines. The first cycle is a Brayton cycle,
describing the evolution of a classical turboshaft, based on the
Klimov TV2 engine. The other four cycles aim at approaching an
Ericsson cycle, by replacing the Brayton cycle adiabatic expansion in
the turbine by quasi-isothermal expansion. The maximum quasi-
Ericsson cycles temperature is set to a lower value than the maximum
Brayton cycle temperature, equal to the Brayton cycle power turbine
inlet temperature, in order to decrease the engine NOx emissions.
Also, the power/expansion ratio distribution over the stages of the gas
generator turbine is maintained the same. In two of the considered
quasi-Ericsson cycles, the efficiencies of the gas generator turbine, as
well as the power/expansion ratio distribution over the stages of the
gas generator turbine are maintained the same as for the reference
case, while for the other two cases, the efficiencies are increased in
order to obtain the same shaft power as in the reference case. For the
two cases respecting the first condition, both the shaft power and the
thermodynamic efficiency of the engine decrease, while for the other
two, the power and efficiency are maintained, as a result of assuming
new, more efficient gas generator turbines.
Abstract: In this paper, a new design of spherical robotic system
based on the concepts of gimbal structure and gyro dynamics is
presented. Robots equipped with multiple wheels and complex
steering mechanics may increase the weight and degrade the energy
transmission efficiency. In addition, the wheeled and legged robots are
relatively vulnerable to lateral impact and lack of lateral mobility.
Therefore, the proposed robotic design uses a spherical shell as the
main body for ground locomotion, instead of using wheel devices.
Three spherical shells are structured in a similar way to a gimbal
device and rotate like a gyro system. The design and mechanism of the
proposed robotic system is introduced. In addition, preliminary results
of the dynamic model based on the principles of planar rigid body
kinematics and Lagrangian equation are included. Simulation results
and rig construction are presented to verify the concepts.
Abstract: Interaction of Schiff base complexes of Iron and
Manganese: Iron [N, N’ Bis (5- (triphenyl phosphonium methyl)
salicylidene) -1, 2 ethanediamine) chloride, [Fe Salen]Cl; Manganese
[N, N’ Bis (5- (triphenyl phosphonium methyl) salicylidene) -1, 2
ethanediamine) acetate, were investigated by spectroscopic and
isothermal titration calorimetry techniques (ITC).
The absorbance spectra of complexes have shown hyper and
hypochromism in the presence of DNA that is indication of
interaction of complexes with DNA. The linear dichroism (LD)
measurements confirmed the bending of DNA in the presence of
complexes.
Furthermore, Isothermal titration calorimetry experiments
approved that complexes bound to DNA on the base of both
electrostatic and hydrophobic interactions. More, ITC profile exhibits
the existence of two binding phases for the complexes. Antibacterial
activity of ligand and complexes were tested in vitro to evaluate their
activity against the gram positive and negative bacteria.
Abstract: The objectives of the study were to determine the
marketing mix factors that influencing tourist’s destination decision
making for cultural tourism in the Chonburi province. Both
quantitative and qualitative data were applied in this study. The
samples of 400 cases for quantitative analysis were tourists (both
Thai and foreign) who were interested in cultural tourism in the
Chonburi province, and traveled to cultural sites in Chonburi and 14
representatives from provincial tourism committee of Chonburi and
local tourism experts. Statistics utilized in this research included
frequency, percentage, mean, standard deviation, and multiple
regression analysis. The study found that Thai and foreign tourists
are influenced by different important marketing mix factors. The
important factors for Thai respondents were physical evidence, price,
people, and place at high importance level. For foreign respondents,
physical evidence, price, people, and process were high importance
level, whereas, product, place and promotion were moderate
importance level.
Abstract: The heavy metal pollution degree in the soils around
the Zangezur copper and molybdenum combine in Syunik Marz,
Armenia was assessed. The results of the study showed that heavy
metal pollution degree in the soils mainly decreased with increasing
distance from the open mine and the ore enrichment combine which
indicated that the open mine and the ore enrichment combine were
the main sources of heavy metal pollution. The only exception was
observed in the northern part of the open mine where pollution
degree in the sites (along the open mine) situated 600 meters far from
the mine was higher than that in the sites located 300 meters far from
the mine. This can be explained by the characteristics of relief and air
currents as well as the weak vegetation cover of these sites and the
characteristics of soil structure. According to geo-accumulation index
(I-geo), contamination factor (Cf), contamination degree (Cd) and
pollution load index (PLI) values, the pollution degree in the soils
around the open mine and the ore enrichment combine was higher
than that in the soils around the tailing dumps which was due to the
proper and accurate operation of the Artsvanik tailing damp and the
recultivation of the Voghji tailing dump.
The high Cu and Mo pollution of the soils was conditioned by the
character of industrial activities, the moving direction of air currents
as well as the physicochemical peculiarities of the soils.
Abstract: In this study, the Compressive strength of concretes
made with Ground Granulated Blast furnace Slag (GGBS),
Pulverised Fuel Ash (PFA), Rice Husk Ash (RHA) and Waste Glass
Powder (WGP) after they were exposed 7800C (exposure duration of
around 60 minutes) and then allowed to cool down gradually in the
furnace for about 280 minutes at water binder ratio of 0.50 was
investigated. GGBS, PFA, RHA and WGP were used to replace up to
20% Portland cement in the control concrete. Test for the
determination of workability, compressive strength and tensile
splitting strength of the concretes were carried out and the results
were compared with control concrete. The test results showed that the
compressive strength decreased by an average of around 30% after
the concretes were exposed to the heating and cooling scenario.
Abstract: Modern Portfolio Theory (MPT) according to
Markowitz states that investors form mean-variance efficient
portfolios which maximizes their utility. Markowitz proposed the
standard deviation as a simple measure for portfolio risk and the
lower semi-variance as the only risk measure of interest to rational
investors. This paper uses a third volatility estimator based on
intraday data and compares three efficient frontiers on the Croatian
Stock Market. The results show that range-based volatility estimator
outperforms both mean-variance and lower semi-variance model.
Abstract: This study aimed to examine the management and
development of forest tourism Kamchanoad. Ban Dung, Udon Thani
sustainability. Data were collected by means of qualitative research
including in-depth interviews, semi- structured, and then the data
were summarized and discussed in accordance with the objectives.
And make a presentation in the form of lectures. The target
population for the study consisted of 16 people, including
representatives from government agencies, community leaders and
the community. The results showed that Guidelines for the
Management and Development of Forest Tourism Kamchanoad
include management of buildings and infrastructure such as roads,
water, electricity, toilets. Other developments are the establishment
of a service center that provides information and resources to
facilitate tourists.; nature trails and informative signage to educate
visitors on the path to the jungle Kamchanoad; forest activities for
tourists who are interested only in occasional educational activities
such as vegetation, etc.; disseminating information on various aspects
of tourism through various channels in both Thailand and English, as
well as a web site to encourage community involvement in the
planning and management of tourism together with the care and
preservation of natural resources and preserving the local cultural
tourist area of Kamchanoad.
Abstract: The purpose of the present work was to develop an
innovative food product with nutritional properties as well as
appealing organoleptic qualities. The product, a jam, was prepared
with the beans’ cooking water combined with fresh apple or carrot,
without the addition of any conservatives. Three different jams were
produced: bean and carrot, bean and apple and bean, apple and
cinnamon. The developed products underwent a sensorial analysis
that revealed that the bean, apple and cinnamon jam was globally
better accepted. However, with this study, the consumers determined
that the bean and carrot jam had the most attractive color and the
bean and apple jam the better consistency. Additionally, it was
possible to analyze the jams for their chemical components, namely
fat, fiber, protein, sugars and antioxidant activity. The obtained
results showed that the bean and carrot jam had the highest lipid
content, while the bean, apple and cinnamon jam had the highest
fiber content, when compared to the other two jams. Regarding the
sugar content, both jams with apple revealed similar sugar values,
which were higher than the sugar content of the bean and carrot jam.
The antioxidant activity was on average 10 mg TE/g.