Abstract: The selective wet-etching of amorphous and
crystalline region of Sb20Se80 thin films was carried out using organic
based solution e.g. amines. We report the development of an in situ
real-time method to study the wet chemical etching process of thin
films. Characterization of the structure and surface of films studied
by X-ray diffraction, SEM and EBSD methods has been done and
potential application suggested.
Abstract: The composition, vapour pressure, and heat capacity
of nine biodiesel fuels from different sources were measured. The
vapour pressure of the biodiesel fuels is modeled assuming an ideal
liquid phase of the fatty acid methyl esters constituting the fuel. New
methodologies to calculate the vapour pressure and ideal gas and
liquid heat capacities of the biodiesel fuel constituents are proposed.
Two alternative optimization scenarios are evaluated: 1) vapour
pressure only; 2) vapour pressure constrained with liquid heat
capacity. Without physical constraints, significant errors in liquid
heat capacity predictions were found whereas the constrained
correlation accurately fit both vapour pressure and liquid heat
capacity.
Abstract: This paper solves the environmental/ economic dispatch
power system problem using the Non-dominated Sorting Genetic
Algorithm-II (NSGA-II) and its hybrid with a Convergence Accelerator
Operator (CAO), called the NSGA-II/CAO. These multiobjective
evolutionary algorithms were applied to the standard IEEE 30-bus
six-generator test system. Several optimization runs were carried out
on different cases of problem complexity. Different quality measure
which compare the performance of the two solution techniques were
considered. The results demonstrated that the inclusion of the CAO
in the original NSGA-II improves its convergence while preserving
the diversity properties of the solution set.
Abstract: The objective of this research work is to discuss the concept of “green growth” in the Republic of Kazakhstan introduced by its government in the “National Sustainable Development Strategy” with the objective of transition to a resource-efficient, “green economy.” We believe that emerging economies like Kazakhstan can pursue a cleaner and more efficient development path by introducing an environmental tax system based on resource consumption rather than only income and labor. The key issues discussed in this article are the eco-efficiency, which refers to closing the gap between economic and ecological efficiencies, and the structural change of the economy toward “green growth.” We also strongly believe that studying the experience of East Asian countries on “green reform” including eco-innovation and “green solutions” in business is essential to the case of Kazakhstan. All of these will raise the status of Kazakhstan to the level of one of the thirty developed countries over the next decades.
Abstract: This paper attempts to model and design a simple
fuzzy logic controller with Variable Reference. The Variable
Reference (VR) is featured as an adaptability element which is
obtained from two known variables – desired system-input and actual
system-output. A simple fuzzy rule-based technique is simulated to
show how the actual system-input is gradually tuned in to a value
that closely matches the desired input. The designed controller is
implemented and verified on a simple heater which is controlled by
PIC Microcontroller harnessed by a code developed in embedded C.
The output response of the PIC-controlled heater is analyzed and
compared to the performances by conventional fuzzy logic
controllers. The novelty of this work lies in the fact that it gives
better performance by using less number of rules compared to
conventional fuzzy logic controllers.
Abstract: Biodiesel production results in glycerol production as
the main by-product in biodiesel industry.One of the utilizations of
glycerol obtained from biodiesel production is as a cement grinding
aid (CGA). Results showed that crude glycerol content was 40.19%
whereas pure glycerol content was 82.15%. BSS value of the cement
with CGA supplementation was higher than that of nonsupplemented
cement (blank) indicating that CGA-supplemented
cement had higher fineness than the non-supplemented one. It was
also found that pure glycerol 95% and TEA 5% at 80ºC was the
optimum CGA used to result in finest cement with BSS value of
4.836 cm2/g. Residue test showed that the smallest percent residue
value (0.11%) was obtained in cement with supplementation of pure
glycerol 95% and TEA 5%. Results of residue test confirmed those of
BSS test showing that cement with supplementation of pure glycerol
95% and TEA 5% had the finest particle size.
Abstract: Attachment of the circulating monocytes to the
endothelium is the earliest detectable events during formation of
atherosclerosis. The adhesion molecules, chemokines and matrix
proteases genes were identified to be expressed in atherogenesis.
Expressions of these genes may influence structural integrity of the
luminal endothelium. The aim of this study is to relate changes in the
ultrastructural morphology of the aortic luminal surface and gene
expressions of the endothelial surface, chemokine and MMP-12 in
normal and hypercholesterolemic rabbits. Luminal endothelial
surface from rabbit aortic tissue was examined by scanning electron
microscopy (SEM) using low vacuum mode to ascertain
ultrastructural changes in development of atherosclerotic lesion. Gene
expression of adhesion molecules, MCP-1 and MMP-12 were studied
by Real-time PCR. Ultrastructural observations of the aortic luminal
surface exhibited changes from normal regular smooth intact
endothelium to irregular luminal surface including marked globular
appearance and ruptures of the membrane layer. Real-time PCR
demonstrated differentially expressed of studied genes in
atherosclerotic tissues. The appearance of ultrastructural changes in
aortic tissue of hypercholesterolemic rabbits is suggested to have
relation with underlying changes of endothelial surface molecules,
chemokine and MMP-12 gene expressions.
Abstract: In this study, the contact problem of a layered composite which consists of two materials with different elastic constants and heights resting on two rigid flat supports with sharp edges is considered. The effect of gravity is neglected. While friction between the layers is taken into account, it is assumed that there is no friction between the supports and the layered composite so that only compressive tractions can be transmitted across the interface. The layered composite is subjected to a uniform clamping pressure over a finite portion of its top surface. The problem is reduced to a singular integral equation in which the contact pressure is the unknown function. The singular integral equation is evaluated numerically and the results for various dimensionless quantities are presented in graphical forms.
Abstract: Ethanol has been known for a long time, being
perhaps the oldest product obtained through traditional biotechnology
fermentation. Agriculture waste as substrate in fermentation is vastly
discussed as alternative to replace edible food and utilization of
organic material. Pineapple peel, highly potential source as substrate
is a by-product of the pineapple processing industry. Bio-ethanol
from pineapple (Ananas comosus) peel extract was carried out by
controlling fermentation without any treatment. Saccharomyces
ellipsoides was used as inoculum in this fermentation process as it is
naturally found at the pineapple skin. In this study, the capability of
Response Surface Methodology (RSM) for optimization of ethanol
production from pineapple peel extract using Saccharomyces
ellipsoideus in batch fermentation process was investigated. Effect of
five test variables in a defined range of inoculum concentration 6-
14% (v/v), pH (4.0-6.0), sugar concentration (14-22°Brix),
temperature (24-32°C) and time of incubation (30-54 hrs) on the
ethanol production were evaluated. Data obtained from experiment
were analyzed with RSM of MINITAB Software (Version 15)
whereby optimum ethanol concentration of 8.637% (v/v) was
determined. The optimum condition of 14% (v/v) inoculum
concentration, pH 6, 22°Brix, 26°C and 30hours of incubation. The
significant regression equation or model at the 5% level with
correlation value of 99.96% was also obtained.
Abstract: The operational behavior of a six-phase squirrel cage
induction machine with faulted stator terminals is presented in this
paper. The study is carried out using the derived mathematical model
of the machine in the arbitrary reference frame. Tests are conducted
on a 1 kW experimental machine.
Steady-state and dynamic performance are analyzed for the
machine unloaded and loaded conditions. The results shows that with
one of the stator phases experiencing either an open- circuit or short
circuit fault the machine still produces starting torque, albeit the
running performance is significantly derated.
Abstract: This interdisciplinary study is an investigation to evaluate user-interfaces in business administration. The study is going to be implemented on two computerized business administration systems with two distinctive user-interfaces, so that differences between the two systems can be determined. Both systems, a commercial and a prototype developed for the purpose of this study, deal with ordering of supplies, tendering procedures, issuing purchase orders, controlling the movement of the stocks against their actual balances on the shelves and editing them on their tabulations. In the second suggested system, modern computer graphics and multimedia issues were taken into consideration to cover the drawbacks of the first system. To highlight differences between the two investigated systems regarding some chosen standard quality criteria, the study employs various statistical techniques and methods to evaluate the users- interaction with both systems. The study variables are divided into two divisions: independent representing the interfaces of the two systems, and dependent embracing efficiency, effectiveness, satisfaction, error rate etc.
Abstract: High strength concrete has been used in situations
where it may be exposed to elevated temperatures. Numerous authors
have shown the significant contribution of polypropylene fiber to the
spalling resistance of high strength concrete.
When cement-based composite that reinforced by polypropylene
fibers heated up to 170 °C, polypropylene fibers readily melt and
volatilize, creating additional porosity and small channels in to the
matrix that cause the poor structure and low strength.
This investigation develops on the mechanical properties of mortar
incorporating polypropylene fibers exposed to high temperature.
Also effects of different pozzolans on strength behaviour of samples
at elevated temperature have been studied.
To reach this purpose, the specimens were produced by partial
replacement of cement with finely ground glass, silica fume and rice
husk ash as high reactive pozzolans. The amount of this replacement
was 10% by weight of cement to find the effects of pozzolans as a
partial replacement of cement on the mechanical properties of
mortars. In this way, lots of mixtures with 0%, 0.5%, 1% and 1.5% of
polypropylene fibers were cast and tested for compressive and
flexural strength, accordance to ASTM standard. After that
specimens being heated to temperatures of 300, 600 °C, respectively,
the mechanical properties of heated samples were tested.
Mechanical tests showed significant reduction in compressive
strength which could be due to polypropylene fiber melting. Also
pozzolans improve the mechanical properties of sampels.
Abstract: In textile industry, besides the conventional textile
products, technical textile goods, that have been brought external
functional properties into, are being developed for technical textile
industry. Especially these products produced with weaving
technology are widely preferred in areas such as sports, geology,
medical, automotive, construction and marine sectors. These textile
products are exposed to various stresses and large deformations under
typical conditions of use. At this point, sufficient and reliable data
could not be obtained with uniaxial tensile tests for determination of
the mechanical properties of such products due to mainly biaxial
stress state. Therefore, the most preferred method is a biaxial tensile
test method and analysis. These tests and analysis is applied to fabrics
with different functional features in order to establish the textile
material with several characteristics and mechanical properties of the
product. Planar biaxial tensile test, cylindrical inflation and bulge
tests are generally required to apply for textile products that are used
in automotive, sailing and sports areas and construction industry to
minimize accidents as long as their service life. Airbags, seat belts
and car tires in the automotive sector are also subject to the same
biaxial stress states, and can be characterized by same types of
experiments. In this study, in accordance with the research literature
related to the various biaxial test methods are compared. Results with
discussions are elaborated mainly focusing on the design of a biaxial
test apparatus to obtain applicable experimental data for developing a
finite element model. Sample experimental results on a prototype
system are expressed.
Abstract: Chitosan is a biopolymer composed of glucosamine
and N-acetyl glucosamine. Solubility and viscosity pose problems in
some applications. These problems can be overcome with unique
modifications. In this study, firstly, chitosan was modified by caffeic
acid and thioglycolic acid, separately. Then, growing effects of these
modified polymers was observed in U937 cell line. Caffeic acid is a
phenolic compound and its modifications act carcinogenic inhibitors
in drugs. Thiolated chitosans are commonly being used for drugdelivery
systems in various routes, because of enhancing
mucoadhesiveness property. U937 cell line was used model cell for
leukaemia. Modifications were achieved by 1 – 15 % binding range.
Increasing binding ratios showed higher radical-scavenging activity
and reducing cell growth, in compared to native chitosan. Caffeic
acid modifications showed higher radical-scavenging activity than
thiolated chitosans at the same concentrations. Caffeic acid and
thioglycolic acid modifications inhibited growth of U937, effectively.
Abstract: The present work describes an experimental
investigation concerning the determination of viscosity behavior with
shear rate and temperature of edible oils: canola; sunflower; corn;
soybean and the no edible oil: Jatropha curcas. Besides these, it was
tested a blend of canola, corn and sunflower oils as well as sunflower
and soybean biodiesel. Based on experiments, it was obtained shear
stress and viscosity at different shear rates of each sample at 40ºC, as
well as viscosity of each sample at various temperatures in the range
of 24 to 85ºC. Furthermore, it was compared the curves obtained for
the viscosity versus temperature with the curves obtained by
modeling the viscosity dependency on temperature using the Vogel
equation. Also a test in a stationary engine was performed in order to
study the energy generation using blends of soybean oil and soybean
biodiesel with diesel.
Abstract: The hydrodynamic processes in bubbly liquid flowing
in tubes and nozzles are studied theoretically and numerically. The
principal regularities of non-stationary processes of boiling liquid
outflow are established under conditions of experiments when the
depressurization of a tube with high pressure inside occurs. The
steady-state solution of bubbly liquid flow in the nozzle of round
cross section with high pressure and temperature conditions inside
bubbles is studied accounting for phase transition and chemical
reactions.
Abstract: The methodology of numerical simulation and calculation of aerodynamic characteristics of aircraft taking into account impact of wake on it has been developed. The results of numerical experiment in comparison with the data obtained in the wind tunnel are presented. Efficiency of methodology of calculation and the reliability of the results is shown.
Abstract: A handful of propagation textbooks that discuss radio frequency (RF) propagation models merely list out the models and perhaps discuss them rather briefly; this may well be frustrating for the potential first time modeller who's got no idea on how these models could have been derived. This paper fundamentally provides an overture in modelling the radio channel. Explicitly, for the modelling practice discussed here, signal strength field measurements had to be conducted beforehand (this was done at 469 MHz); to be precise, this paper primarily concerns empirically/statistically modelling the radio channel, and thus provides results obtained from empirically modelling the environments in question. This paper, on the whole, proposes three propagation models, corresponding to three experimented environments. Perceptibly, the models have been derived by way of making the most use of statistical measures. Generally speaking, the first two models were derived via simple linear regression analysis, whereas the third have been originated using multiple regression analysis (with five various predictors). Additionally, as implied by the title of this paper, both indoor and outdoor environments have been experimented; however, (somewhat) two of the environments are neither entirely indoor nor entirely outdoor. The other environment, however, is completely indoor.
Abstract: In this study, a low temperature sensor highly selective to CO in presence of methane is fabricated by using 4 nm SnO2 quantum dots (QDs) prepared by sonication assisted precipitation. SnCl4 aqueous solution was precipitated by ammonia under sonication, which continued for 2 h. A part of the sample was then dried and calcined at 400°C for 1.5 h and characterized by XRD and BET. The average particle size and the specific surface area of the SnO2 QDs as well as their sensing properties were compared with the SnO2 nano-particles which were prepared by conventional sol-gel method. The BET surface area of sonochemically as-prepared product and the one calcined at 400°C after 1.5 hr are 257 m2/gr and 212 m2/gr respectively while the specific surface area for SnO2 nanoparticles prepared by conventional sol-gel method is about 80m2/gr. XRD spectra revealed pure crystalline phase of SnO2 is formed for both as-prepared and calcined samples of SnO2 QDs. However, for the sample prepared by sol-gel method and calcined at 400°C SnO crystals are detected along with those of SnO2. Quantum dots of SnO2 show exceedingly high sensitivity to CO with different concentrations of 100, 300 and 1000 ppm in whole range of temperature (25- 350°C). At 50°C a sensitivity of 27 was obtained for 1000 ppm CO, which increases to a maximum of 147 when the temperature rises to 225°C and then drops off while the maximum sensitivity for the SnO2 sample prepared by the sol-gel method was obtained at 300°C with the amount of 47.2. At the same time no sensitivity to methane is observed in whole range of temperatures for SnO2 QDs. The response and recovery times of the sensor sharply decreases with temperature, while the high selectivity to CO does not deteriorate.
Abstract: Robots- visual perception is a field that is gaining
increasing attention from researchers. This is partly due to emerging
trends in the commercial availability of 3D scanning systems or
devices that produce a high information accuracy level for a variety of
applications. In the history of mining, the mortality rate of mine workers
has been alarming and robots exhibit a great deal of potentials to
tackle safety issues in mines. However, an effective vision system
is crucial to safe autonomous navigation in underground terrains.
This work investigates robots- perception in underground terrains
(mines and tunnels) using statistical region merging (SRM) model.
SRM reconstructs the main structural components of an imagery
by a simple but effective statistical analysis. An investigation is
conducted on different regions of the mine, such as the shaft, stope
and gallery, using publicly available mine frames, with a stream of
locally captured mine images. An investigation is also conducted on a
stream of underground tunnel image frames, using the XBOX Kinect
3D sensors. The Kinect sensors produce streams of red, green and
blue (RGB) and depth images of 640 x 480 resolution at 30 frames per
second. Integrating the depth information to drivability gives a strong
cue to the analysis, which detects 3D results augmenting drivable and
non-drivable regions in 2D. The results of the 2D and 3D experiment
with different terrains, mines and tunnels, together with the qualitative
and quantitative evaluation, reveal that a good drivable region can be
detected in dynamic underground terrains.