Abstract: Gas hydrates can agglomerate and block multiphase oil and gas pipelines when water is present at hydrate forming conditions. Using "Cold Flow Technology", the aim is to condition gas hydrates so that they can be transported as a slurry mixture without a risk of agglomeration. During the pipeline shut down however, hydrate particles may settle in bends and build hydrate plugs. An experimental setup has been designed and constructed to study the flow of such plugs at start up operations. Experiments have been performed using model fluid and model hydrate particles. The propagations of initial plugs in a bend were recorded with impedance probes along the pipe. The experimental results show a dispersion of the plug front. A peak in pressure drop was also recorded when the plugs were passing the bend. The evolutions of the plugs have been simulated by numerical integration of the incompressible mass balance equations, with an imposed mixture velocity. The slip between particles and carrier fluid has been calculated using a drag relation together with a particle-fluid force balance.
Abstract: MC (Management Control)& IC (Internal Control) – what is the relationship? (an empirical study into the definitions between MC and IC) based on the wider considerations of Internal Control and Management Control terms, attention is focused not only on the financial aspects but also more on the soft aspects of the business, such as culture, behaviour, standards and values. The limited considerations of Management Control are focused mainly in the hard, financial aspects of business operation. The definitions of Management Control and Internal Control are often used interchangeably and the results of this empirical study reveal that Management Control is part of Internal Control, there is no causal link between the two concepts. Based on the interpretation of the respondents, the term Management Control has moved from a broad term to a more limited term with the soft aspects of the influencing of behaviour, performance measurements, incentives and culture. This paper is an exploratory study based on qualitative research and on a qualitative matrix method analysis of the thematic definition of the terms Management Control and Internal Control.
Abstract: In this study, the numerical solution of unsteady flow
between two concentric rotating spheres with suction and blowing at
their boundaries is presented. The spheres are rotating about a
common axis of rotation while their angular velocities are constant.
The Navier-Stokes equations are solved by employing the finite
difference method and implicit scheme. The resulting flow patterns
are presented for various values of the flow parameters including
rotational Reynolds number Re , and a blowing/suction Reynolds
number Rew . Viscous torques at the inner and the outer spheres are
calculated, too. It is seen that increasing the amount of suction and
blowing decrease the size of eddies generated in the annulus.
Abstract: The objective of this work is to study the influence of the properties of the substrate on the retrofit (thin repair) of damaged concrete elements, with the SCC. Fluidity, principal characteristic of the SCC, would enable it to cover and adhere to the concrete to be repaired. Two aspects of repair are considered, the bond (Adhesion) and the tensile strength and the cracking. The investigation is experimental; It was conducted over test specimens made up of ordinary concrete prepared and hardened in advance (the material to be repaired) over which a self compacting concrete layer is cast. Three alternatives of SC concrete and one ordinary concrete (comparison) were tested. It appears that the self-compacting concrete constitutes a good material for repairing. It follows perfectly the surfaces- forms to be repaired and allows a perfect bond. Fracture tests made on specimens of self-compacting concrete show a brittle behaviour. However when a small percentage of fibres is added, the resistance to cracking is very much improve.
Abstract: Construction of tunnels is connected with high
uncertainty in the field of costs, construction period, safety and
impact on surroundings. Risk management became therefore a
common part of tunnel projects, especially after a set of fatal
collapses occurred in 1990's. Such collapses are caused usually by
combination of factors that can be divided into three main groups, i.e.
unfavourable geological conditions, failures in the design and
planning or failures in the execution.
This paper suggests a procedure enabling quantification of the
excavation risk related to extraordinary accidents using FTA and
ETA tools. It will elaborate on a common process of risk analysis and
enable the transfer of information and experience between particular
tunnel construction projects. Further, it gives a guide for designers,
management and other participants, how to deal with risk of such
accidents and how to make qualified decisions based on a
probabilistic approach.
Abstract: In the planning point of view, it is essential to have
mode choice, due to the massive amount of incurred in transportation
systems. The intercity travellers in Libya have distinct features, as
against travellers from other countries, which includes cultural and
socioeconomic factors. Consequently, the goal of this study is to
recognize the behavior of intercity travel using disaggregate models,
for projecting the demand of nation-level intercity travel in Libya.
Multinomial Logit Model for all the intercity trips has been
formulated to examine the national-level intercity transportation in
Libya. The Multinomial logit model was calibrated using nationwide
revealed preferences (RP) and stated preferences (SP) survey. The
model was developed for deference purpose of intercity trips (work,
social and recreational). The variables of the model have been
predicted based on maximum likelihood method. The data needed for
model development were obtained from all major intercity corridors
in Libya. The final sample size consisted of 1300 interviews. About
two-thirds of these data were used for model calibration, and the
remaining parts were used for model validation. This study, which is
the first of its kind in Libya, investigates the intercity traveler’s
mode-choice behavior. The intercity travel mode-choice model was
successfully calibrated and validated. The outcomes indicate that, the
overall model is effective and yields higher precision of estimation.
The proposed model is beneficial, due to the fact that, it is receptive
to a lot of variables, and can be employed to determine the impact of
modifications in the numerous characteristics on the need for various
travel modes. Estimations of the model might also be of valuable to
planners, who can estimate possibilities for various modes and
determine the impact of unique policy modifications on the need for
intercity travel.
Abstract: Since after the historical moment of Malaysia
Independence Day on the year of 1957, the government had been trying hard in order to find the most efficient methods in learning.
However, it is hard to actually access and evaluate students whom will then be called an excellent student. It because in our realtime
student who excellent is only excel in academic. This evaluation
become a problem because it not balance in our real life interm of to get an excellent student in whole area in their involvement of curiculum and co-curiculum. To overcome this scenario, we
proposed a method called Student Idol to evaluate student through
three categories which are academic, co-curiculum and leadership.
All the categories have their own merit point. Using this method, student will be evaluated more accurate compared to the previously.
So, teacher can easily evaluate their student without having any emotion factor, relation factor and others. As conclustion this method will helps student evaluation more accurate and valid.
Abstract: Recent advancements in sensor technologies and
Wireless Body Area Networks (WBANs) have led to the
development of cost-effective healthcare devices which can be used
to monitor and analyse a person-s physiological parameters from
remote locations. These advancements provides a unique opportunity
to overcome current healthcare challenges of low quality service
provisioning, lack of easy accessibility to service varieties, high costs
of services and increasing population of the elderly experienced
globally. This paper reports on a prototype implementation of an
architecture that seamlessly integrates Wireless Body Area Network
(WBAN) with Web services (WS) to proactively collect
physiological data of remote patients to recommend diagnostic
services. Technologies based upon WBAN and WS can provide
ubiquitous accessibility to a variety of services by allowing
distributed healthcare resources to be massively reused to provide
cost-effective services without individuals physically moving to the
locations of those resources. In addition, these technologies can
reduce costs of healthcare services by allowing individuals to access
services to support their healthcare. The prototype uses WBAN body
sensors implemented on arduino fio platforms to be worn by the
patient and an android smart phone as a personal server. The
physiological data are collected and uploaded through GPRS/internet
to the Medical Health Server (MHS) to be analysed. The prototype
monitors the activities, location and physiological parameters such as
SpO2 and Heart Rate of the elderly and patients in rehabilitation.
Medical practitioners would have real time access to the uploaded
information through a web application.
Abstract: The major part of light weight timber constructions
consists of insulation. Mineral wool is the most commonly used
insulation due to its cost efficiency and easy handling. The fiber
orientation and porosity of this insulation material enables flowthrough.
The air flow resistance is low. If leakage occurs in the
insulated bay section, the convective flow may cause energy losses
and infiltration of the exterior wall with moisture and particles. In
particular the infiltrated moisture may lead to thermal bridges and
growth of health endangering mould and mildew. In order to prevent
this problem, different numerical calculation models have been
developed. All models developed so far have a potential for
completion. The implementation of the flow-through properties of
mineral wool insulation may help to improve the existing models.
Assuming that the real pressure difference between interior and
exterior surface is larger than the prescribed pressure difference in the
standard test procedure for mineral wool ISO 9053 / EN 29053,
measurements were performed using the measurement setup for
research on convective moisture transfer “MSRCMT".
These measurements show, that structural inhomogeneities of
mineral wool effect the permeability only at higher pressure
differences, as applied in MSRCMT. Additional microscopic
investigations show, that the location of a leak within the
construction has a crucial influence on the air flow-through and the
infiltration rate. The results clearly indicate that the empirical values
for the acoustic resistance of mineral wool should not be used for the
calculation of convective transfer mechanisms.
Abstract: One of the major, difficult tasks in automated video
surveillance is the segmentation of relevant objects in the scene.
Current implementations often yield inconsistent results on average
from frame to frame when trying to differentiate partly occluding
objects. This paper presents an efficient block-based segmentation
algorithm which is capable of separating partly occluding objects and
detecting shadows. It has been proven to perform in real time with a
maximum duration of 47.48 ms per frame (for 8x8 blocks on a
720x576 image) with a true positive rate of 89.2%. The flexible
structure of the algorithm enables adaptations and improvements with
little effort. Most of the parameters correspond to relative differences
between quantities extracted from the image and should therefore not
depend on scene and lighting conditions. Thus presenting a
performance oriented segmentation algorithm which is applicable in
all critical real time scenarios.
Abstract: Bonding has become a routine procedure in several
dental specialties – from prosthodontics to conservative dentistry and
even orthodontics. In many of these fields it is important to be able to
investigate the bonded interfaces to assess their quality. All currently
employed investigative methods are invasive, meaning that samples
are destroyed in the testing procedure and cannot be used again. We
have investigated the interface between human enamel and bonded
ceramic brackets non-invasively, introducing a combination of new
investigative methods – optical coherence tomography (OCT),
fluorescence OCT and confocal microscopy (CM). Brackets were
conventionally bonded on conditioned buccal surfaces of teeth. The
bonding was assessed using these methods. Three dimensional
reconstructions of the detected material defects were developed using
manual and semi-automatic segmentation. The results clearly prove
that OCT, fluorescence OCT and CM are useful in orthodontic
bonding investigations.
Abstract: The potential, opportunities and drawbacks of biogas
technology use in Turkey are evaluated in this paper. Turkey is
dependent on foreign sources of energy. Therefore, use of biogas
technology would provide a safe way of waste disposal and recovery
of renewable energy, particularly from a sustainable domestic source,
which is less unlikely to be influenced by international price or
political fluctuations. Use of biogas technology would especially
meet the cooking, heating and electricity demand in rural areas and
protect the environment, additionally creating new job opportunities
and improving social-economical conditions.
Abstract: Kepsut-Dursunbey volcanic field (KDVF) is located
in NW Turkey and contains various products of the post-collisional
Neogene magmatic activity. Two distinct volcanic suites have been
recognized; the Kepsut volcanic suite (KVS) and the Dursunbey
volcanic suite (DVS). The KVS includes basaltic trachyandesitebasaltic
andesite-andesite lavas and associated pyroclastic rocks. The
DVS consists of dacite-rhyodacite lavas and extensive pumice-ash
fall and flow deposits. Petrographical features (i.e. existence of
xenocrysts, glomerocrysts, and mixing-compatible textures) and
mineral chemistry of phenocryst assemblages of both suites provide
evidence for magma mixing/AFC. Calculated crystallization
pressures and temperatures give values of 5.7–7.0 kbar and 927–982
°C for the KVS and 3.7–5.3 kbar and 783-787°C for the DVS,
indicating separate magma reservoirs and crystallization in magma
chambers at deep and mid crustal levels, respectively. These
observations support the establishment and evolution of KDVF
magma system promoted by episodic basaltic inputs which may
generate and mix with crustal melts.
Abstract: In this paper, a new time-delay estimation
technique based on the cross IB-energy operator [5] is
introduced. This quadratic energy detector measures how
much a signal is present in another one. The location of the
peak of the energy operator, corresponding to the maximum of
interaction between the two signals, is the estimate of the
delay. The method is a fully data-driven approach. The
discrete version of the continuous-time form of the cross IBenergy
operator, for its implementation, is presented. The
effectiveness of the proposed method is demonstrated on real
underwater acoustic signals arriving from targets and the
results compared to the cross-correlation method.
Abstract: The main objective of this paper is to analyse the influence of preparation and control of orders on performance. The focused activities explored in this research are: procurement, production and distribution. These changes in performance were obtained through improvement of the supply chain. It is proved using all the company activities that it is possible to increase de efficiency and do services in an adequate way, placing the products in the market efficiently. For that, it was explored the importance of the supply chain, with privilege to the practical environment and the quantification of the obtained results.
Abstract: In this paper, a new approach for target recognition based on the Empirical mode decomposition (EMD) algorithm of Huang etal. [11] and the energy tracking operator of Teager [13]-[14] is introduced. The conjunction of these two methods is called Teager-Huang analysis. This approach is well suited for nonstationary signals analysis. The impulse response (IR) of target is first band pass filtered into subsignals (components) called Intrinsic mode functions (IMFs) with well defined Instantaneous frequency (IF) and Instantaneous amplitude (IA). Each IMF is a zero-mean AM-FM component. In second step, the energy of each IMF is tracked using the Teager energy operator (TEO). IF and IA, useful to describe the time-varying characteristics of the signal, are estimated using the Energy separation algorithm (ESA) algorithm of Maragos et al .[16]-[17]. In third step, a set of features such as skewness and kurtosis are extracted from the IF, IA and IMF energy functions. The Teager-Huang analysis is tested on set of synthetic IRs of Sonar targets with different physical characteristics (density, velocity, shape,? ). PCA is first applied to features to discriminate between manufactured and natural targets. The manufactured patterns are classified into spheres and cylinders. One hundred percent of correct recognition is achieved with twenty three echoes where sixteen IRs, used for training, are free noise and seven IRs, used for testing phase, are corrupted with white Gaussian noise.
Abstract: A composite made of plasma functionalized multiwall
carbon nanotubes (MWNTs) coated with SnO2 was synthesized by
sonochemical precipitation method. Thick layer of this
nanocomposite material was used as ethanol sensor at low
temperatures. The composite sensitivity for ethanol has increased by
a factor of 2 at room temperature and by a factor of 13 at 250°C in
comparison to that of pure SnO2. SEM image of nanocomposite
material showed MWNTs were embedded in SnO2 matrix and also a
higher surface area was observed in the presence of functionalized
MWNTs. Greatly improved sensitivity of the composite material to
ethanol can be attributed to new gas accessing passes through
MWNTs and higher specific surface area.
Abstract: This research details a Computational Fluid Dynamics (CFD) approach to model fluid flow in a journal bearing with 8 equispaced semi-circular axial grooves. Water is used as the lubricant and is fed from one end of the bearing to the other, under pressure. The geometry of the bearing is modeled using a commercially available modeling software GAMBIT and the flow analysis is performed using a dedicated CFD analysis software FLUENT. The pressure distribution in the bearing clearance is obtained from FLUENT for various whirl ratios and is used to calculate the hydrodynamic force components in the radial and tangential direction of the bearing. These values along with the various whirl speeds can be used to do a regression analysis to determine the stiffness and damping coefficients. The values obtained are then compared with the stiffness and damping coefficients of a 3 Axial groove water lubricated journal bearing and those obtained from a FORTRAN code for a similar bearing.
Abstract: Abstraction of water from the dry river sand-beds is
well-known as an alternative source of water during dry seasons.
Internally, because of the form of sand particles, voids are created
which can store water in the riverbeds. Large rivers are rare in South
Africa. Many rivers are sand river types and without water during the
prolonged dry periods. South Africa has not taken full advantage of
water storage in sand as a solution to the growing water scarcity both
in urban and rural areas. The paper reviews the benefits of run-off
storage in sand reservoirs gained from other arid areas and need for
adoption in rural areas of South Africa as an alternative water supply
where it is probable.
Abstract: This paper characterizes the effects of artificial short
term aging in the laboratory on the rheological properties of virgin
80/100 penetration grade asphalt binder. After several years in
service, asphalt mixture started to deteriorate due to aging. Aging is a
complex physico-chemical phenomenon that influences asphalt
binder rheological properties causing a deterioration in asphalt
mixture performance. To ascertain asphalt binder aging effects, the
virgin, artificially aged and extracted asphalt binder were tested via
the Rolling Thin film Oven (RTFO), Dynamic Shear Rheometer
(DSR) and Rotational Viscometer (RV). A comparative study
between laboratory and field aging conditions were also carried out.
The results showed that the specimens conditioned for 85 minutes
inside the RTFO was insufficient to simulate the actual short term
aging caused that took place in the field under Malaysian field
conditions