Abstract: The economic use and ease of construction of profiled
deck composite slab is marred with the complex and un-economic
strength verification required for the serviceability and general safety
considerations. Beside these, albeit factors such as shear span length,
deck geometries and mechanical frictions greatly influence the
longitudinal shear strength, that determines the ultimate strength of
profiled deck composite slab, and number of methods available for its
determination; partial shear and slope-intercept are the two methods
according to Euro-code 4 provision. However, the complexity
associated with shear behavior of profiled deck composite slab, the
use of these methods in determining the load carrying capacities of
such slab yields different and conflicting values. This couple with the
time and cost constraint associated with the strength verification is a
source of concern that draws more attentions nowadays, the issue is
critical. Treating some of these known shear strength influencing
factors as random variables, the load carrying capacity violation of
profiled deck composite slab from the use of the two-methods
defined according to Euro-code 4 are determined using reliability
approach, and comparatively studied. The study reveals safety values
from the use of m-k method shows good standing compared with that
from the partial shear method.
Abstract: In this paper air quality conditions in Makkah and
Leeds are compared. These two cities have totally different climatic
conditions. Makkah climate is characterised as hot and dry (arid)
whereas that of Leeds is characterised as cold and wet (temperate).
This study uses air quality data from 2012 collected in Makkah,
Saudi Arabia and Leeds, UK. The concentrations of all pollutants,
except NO are higher in Makkah. Most notable, the concentrations of
PM10 are much higher in Makkah than in Leeds. This is probably due
to the arid nature of climatic conditions in Makkah and not solely due
to anthropogenic emission sources, otherwise like PM10 some of the
other pollutants, such as CO, NO, and SO2 would have shown much
greater difference between Leeds and Makkah. Correlation analysis is
performed between different pollutants at the same site and the same
pollutants at different sites. In Leeds the correlation between PM10
and other pollutants is significantly stronger than in Makkah. Weaker
correlation in Makkah is probably due to the fact that in Makkah
most of the gaseous pollutants are emitted by combustion processes,
whereas most of the PM10 is generated by other sources, such as
windblown dust, re-suspension, and construction activities. This is in
contrast to Leeds where all pollutants including PM10 are
predominantly emitted by combustions, such as road traffic.
Furthermore, in Leeds frequent rains wash out most of the
atmospheric particulate matter and suppress re-suspension of dust.
Temporal trends of various pollutants are compared and discussed.
This study emphasises the role of climatic conditions in managing air
quality, and hence the need for region-specific controlling strategies
according to the local climatic and meteorological conditions.
Abstract: In recent decades, particulate matter (PM10) have
received much attention due to its potential adverse health impact and
the subsequent need to better control or regulate these pollutants.
The aim of this paper is focused on study risk assessment of PM10
in four different districts (Shebikah, Masfalah, Aziziyah, Awali) in
Makkah, Saudi Arabia during the period from 1 Ramadan 1434 AH -
27 Safar 1435 AH. Samples were collected by using Low Volume
Sampler (LVS Low Volume Sampler) device and filtration method
for estimating the total concentration of PM10.
The study indicated that the mean PM10 concentrations were 254.6
(186.1 - 343.2) μg/m3 in Shebikah, 184.9 (145.6 - 271.4) μg/m3 in
Masfalah, 162.4 (92.4-253.8) μg/m3 in Aziziyah, and 56.0 (44.5 -
119.8) μg/m3 in Awali. These values did not exceed the permissible
limits in PME (340 μg/m3 as daily average). Furthermore, health
assessment is carried out using AirQ2.2.3 model to estimate the
number of hospital admissions due to respiratory diseases. The
cumulative number of cases per 100,000 were 1534 (18-3050 case),
which lower than that recorded in the United States, Malaysia. The
concentration response coefficient was 0.49 (95% CI 0.05 - 0.70) per
10 μg/m3 increase of PM10.
Abstract: Biodiesel, as an alternative renewable fuel, has been
receiving increasing attention due to the limited supply of fossil fuels
and the increasing need for energy. Microalgae are promising source
for lipids, which can be converted to biodiesel. The biodiesel
production from microalgae lipids using lipase catalyzed reaction in
supercritical CO2 medium has several advantages over conventional
production processes. However, identifying the optimum microalgae
lipid extraction and transesterification conditions is still a challenge.
In this study, the quality of biodiesel produced from lipids extracted
from Scenedesmus sp. and their enzymatic transesterification using
supercritical carbon dioxide have been investigated. At the optimum
conditions, the highest biodiesel production yield was found to be
82%. The fuel properties of the produced biodiesel, without any
separation step, at optimum reaction condition, were determined and
compared to ASTM standards. The properties were found to comply
with the limits, and showed a low glycerol content, without any
separation step.
Abstract: This paper presents an application of a “Systematic
Soft Domain Driven Design Framework” as a soft systems approach
to domain-driven design of information systems development. The
framework use SSM as a guiding methodology within which we have
embedded a sequence of design tasks based on the UML leading to
the implementation of a software system using the Naked Objects
framework. This framework have been used in action research
projects that have involved the investigation and modelling of
business processes using object-oriented domain models and the
implementation of software systems based on those domain models.
Within this framework, Soft Systems Methodology (SSM) is used as
a guiding methodology to explore the problem situation and to
develop the domain model using UML for the given business
domain. The framework is proposed and evaluated in our previous
works, and a real case study “Information Retrieval System for
academic research” is used, in this paper, to show further practice and
evaluation of the framework in different business domain. We argue
that there are advantages from combining and using techniques from
different methodologies in this way for business domain modelling.
The framework is overviewed and justified as multimethodology
using Mingers multimethodology ideas.
Abstract: In this paper, we are interested in the problem of
finding similar images in a large database. For this purpose we
propose a new algorithm based on a combination of the 2-D
histogram intersection in the HSV space and statistical moments. The
proposed histogram is based on a 3x3 window and not only on the
intensity of the pixel. This approach overcome the drawback of the
conventional 1-D histogram which is ignoring the spatial distribution
of pixels in the image, while the statistical moments are used to
escape the effects of the discretisation of the color space which is
intrinsic to the use of histograms. We compare the performance of
our new algorithm to various methods of the state of the art and we
show that it has several advantages. It is fast, consumes little memory
and requires no learning. To validate our results, we apply this
algorithm to search for similar images in different image databases.
Abstract: Steady three-dimensional and two free surface waves
generated by moving bodies are presented, the flow problem to be
simulated is rich in complexity and poses many modeling challenges
because of the existence of breaking waves around the ship hull, and
because of the interaction of the two-phase flow with the turbulent
boundary layer. The results of several simulations are reported. The
first study was performed for NACA0012 of hydrofoil with different
meshes, this section is analyzed at h/c= 1, 0345 for 2D. In the second
simulation a mathematically defined Wigley hull form is used to
investigate the application of a commercial CFD code in prediction of
the total resistance and its components from tangential and normal
forces on the hull wetted surface. The computed resistance and wave
profiles are used to estimate the coefficient of the total resistance for
Wigley hull advancing in calm water under steady conditions. The
commercial CFD software FLUENT version 12 is used for the
computations in the present study. The calculated grid is established
using the code computer GAMBIT 2.3.26. The shear stress k-ωSST
model is used for turbulence modeling and the volume of fluid
technique is employed to simulate the free-surface motion. The
second order upwind scheme is used for discretizing the convection
terms in the momentum transport equations, the Modified HRIC
scheme for VOF discretization. The results obtained compare well
with the experimental data.
Abstract: Steady three-dimensional and two free surface waves
generated by moving bodies are presented, the flow problem to be
simulated is rich in complexity and poses many modeling challenges
because of the existence of breaking waves around the ship hull, and
because of the interaction of the two-phase flow with the turbulent
boundary layer. The results of several simulations are reported. The
first study was performed for NACA0012 of hydrofoil with different
meshes, this section is analyzed at h/c= 1, 0345 for 2D. In the second
simulation a mathematically defined Wigley hull form is used to
investigate the application of a commercial CFD code in prediction of
the total resistance and its components from tangential and normal
forces on the hull wetted surface. The computed resistance and wave
profiles are used to estimate the coefficient of the total resistance for
Wigley hull advancing in calm water under steady conditions. The
commercial CFD software FLUENT version 12 is used for the
computations in the present study. The calculated grid is established
using the code computer GAMBIT 2.3.26. The shear stress k-ωSST
model is used for turbulence modeling and the volume of fluid
technique is employed to simulate the free-surface motion. The
second order upwind scheme is used for discretizing the convection
terms in the momentum transport equations, the Modified HRIC
scheme for VOF discretization. The results obtained compare well
with the experimental data.
Abstract: Atmospheric carbon dioxide emissions are considered
as the greatest environmental challenge the world is facing today.
The tasks to control the emissions include the recovery of CO2 from
flue gas. This concern has been improved due to recent advances in
materials process engineering resulting in the development of
inorganic gas separation membranes with excellent thermal and
mechanical stability required for most gas separations. This paper,
therefore, evaluates the performance of a highly selective inorganic
membrane for CO2 recovery applications. Analysis of results
obtained is in agreement with experimental literature data. Further
results show the prediction performance of the membranes for gas
separation and the future direction of research. The materials
selection and the membrane preparation techniques are discussed.
Method of improving the interface defects in the membrane and its
effect on the separation performance has also been reviewed and in
addition advances to totally exploit the potential usage of this
innovative membrane.
Abstract: The growth in the volume of text data such as books
and articles in libraries for centuries has imposed to establish
effective mechanisms to locate them. Early techniques such as
abstraction, indexing and the use of classification categories have
marked the birth of a new field of research called "Information
Retrieval". Information Retrieval (IR) can be defined as the task of
defining models and systems whose purpose is to facilitate access to
a set of documents in electronic form (corpus) to allow a user to find
the relevant ones for him, that is to say, the contents which matches
with the information needs of the user. This paper presents a new
semantic indexing approach of a documentary corpus. The indexing
process starts first by a term weighting phase to determine the
importance of these terms in the documents. Then the use of a
thesaurus like Wordnet allows moving to the conceptual level.
Each candidate concept is evaluated by determining its level of
representation of the document, that is to say, the importance of the
concept in relation to other concepts of the document. Finally, the
semantic index is constructed by attaching to each concept of the
ontology, the documents of the corpus in which these concepts are
found.
Abstract: The aim of this exploratory research is to understand
further how organisations can evaluate their activities, which
generate knowledge creation, to meet changing stakeholder
expectations. A Scale of Knowledge (SoK) Framework is proposed
which links knowledge management and organisational activities to
changing stakeholder expectations. The framework was informed by
the knowledge management literature, as well as empirical work
conducted via a single case study of a multi-site hospital organisation
in Saudi Arabia. Eight in-depth semi-structured interviews were
conducted with managers from across the organisation regarding
current and future stakeholder expectations, organisational
strategy/activities and knowledge management. Data were analysed
using thematic analysis and a hierarchical value map technique to
identify activities that can produce further knowledge and
consequently impact on how stakeholder expectations are met.
The SoK Framework developed may be useful to practitioners as
an analytical aid to determine if current organisational activities
produce organisational knowledge which helps them meet
(increasingly higher levels of) stakeholder expectations. The
limitations of the research and avenues for future development of the
proposed framework are discussed.
Abstract: Pt/γ-Al2O3 membrane catalysts were prepared via an
evaporative-crystallization deposition method. The obtained Pt/γ-
Al2O3 catalyst activity was tested after characterization (SEM-EDAX
observation, BET measurement, permeability assessment) in the
catalytic oxidation of selected volatile organic compound (VOC) i.e.
propane, fed in mixture of oxygen. The VOC conversion (nearly
90%) obtained by varying the operating temperature showed that
flow-through membrane reactor might do better in the abatement of
VOCs.
Abstract: This paper aims to investigate the influence of quality
of education and quality of research, provided by local educational
institutions, on the adoption of Information and Communication
Technology (ICT) in managing business operations for companies in
Saudi market. A model was developed and tested using data collected
from 138 Chief Executive Officers (CEOs) of foreign companies in
diverse business sectors. The data is analyzed and managed using
multivariate approaches through standard statistical packages. The
results showed that educational quality has little contribution to the
ICT adoption while research quality seems to play a more prominent
role. These results are analyzed in terms of business environment and
market constraints and further extended to the perceived effectiveness
of applied pedagogical approaches in schools and universities.
Abstract: This paper is a report on the findings of a study
conducted at the Institute of Public Administration (IPA) in Saudi
Arabia. The paper applied both qualitative and quantitative
approaches to assess the levels of basic computer applications’ skills
among students enrolled in the preparatory programs of the
institution. Qualitative data have been collected from semi-structured
interviews with the instructors who have previously been assigned to
teach Introduction to information technology courses. Quantitative
data were collected by executing a self-report questionnaire and a
written statistical test. Three hundred eighty enrolled students
responded to the questionnaire and one hundred forty two
accomplished the statistical test. The results indicate the lack of
necessary skills to deal with computer applications among most of
the students who are enrolled in the IPA’s preparatory programs.
Abstract: There is a trend in development discourse to
understand and explain the level of corruption in Nigeria, its anticorruption
crusade and why it is failing, as well as its level of
compliance with International standards of United Nations
Convention against Corruption (UNCAC) & African Union
Convention on Converting and Preventing Corruption) to which
Nigeria is a signatory. This paper discusses the legal and
Constitutional provisions relating to corrupt practices and safeguards
in Nigeria, as well as the obstacles to the implementation of these
Conventions.
The paper highlights the challenges posed to the Anti-Corruption
crusade by analysing the loopholes that exist both in administrative
structure and in scope of the relevant laws. The paper argues that
Nigerian Constitution did not make adequate provisions for the
implementation of the conventions, hence a proposal which will
ensure adequate provision for implementing the conventions to better
the lives of Nigerians. The paper concludes that there is the need to
build institutional parameters, adequate constitutional and structural
safeguards, as well as to synergise strategies, collaborations and
alliances to facilitate the timely domestication and implementation of
the conventions.
Abstract: Catalytic combustion of methane is imperative due to
stability of methane at low temperature. Methane (CH4), therefore,
remains unconverted in vehicle exhausts thereby causing greenhouse
gas GHG emission problem. In this study, heterogeneous catalysts of
palladium with bio-char (2 wt% Pd/Bc) and Al2O3 (2wt% Pd/ Al2O3)
supports were prepared by incipient wetness impregnation and then
subsequently tested for catalytic combustion of CH4. Support-porous
heterogeneous catalytic combustion (HCC) material were selected
based on factors such as surface area, porosity, thermal stability,
thermal conductivity, reactivity with reactants or products, chemical
stability, catalytic activity, and catalyst life. Sustainable and
renewable support-material of bio-mass char derived from palm shell
waste material was compared with those from the conventional
support-porous materials. Kinetic rate of reaction was determined for
combustion of methane on Palladium (Pd) based catalyst with Al2O3
support and bio-char (Bc). Material characterization was done using
TGA, SEM, and BET surface area. The performance test was
accomplished using tubular quartz reactor with gas mixture ratio of
3% methane and 97% air. The methane porous-HCC conversion was
carried out using online gas analyzer connected to the reactor that
performed porous-HCC. BET surface area for prepared 2 wt% Pd/Bc
is smaller than prepared 2wt% Pd/ Al2O3 due to its low porosity
between particles. The order of catalyst activity based on kinetic rate
on reaction of catalysts in low temperature was 2wt%
Pd/Bc>calcined 2wt% Pd/ Al2O3> 2wt% Pd/ Al2O3>calcined 2wt%
Pd/Bc. Hence agro waste material can successfully be utilized as an
inexpensive catalyst support material for enhanced CH4 catalytic
combustion.
Abstract: The Malaysian government had consistently revived
its campaign for “Buy Malaysian Goods” from time to time. The
purpose of the campaign is to remind consumers to be ethnocentric
and patriotic when purchasing product and services. This is necessary
to ensure high demand for local products and services compared to
foreign products. However, the decline of domestic investment in
2012 has triggered concern for the Malaysian economy. Hence, this
study attempts to determine the drivers of actual purchasing behavior,
intention to purchase domestic products and ethnocentrism. The
study employs the cross-sectional primary data, self-administered on
household, selected using stratified random sampling in four
Malaysian regions. A nine factor driver of actual domestic purchasing
behavior (culture openness, conservatism, collectivism, patriotism,
control belief, interest in foreign travel, attitude, ethnocentrism and
intention) were measured utilizing 60 items, using 7-point Likertscale.
From 1000 questionnaires distributed, a sample of 486 were
returned representing 48.6 percent response rate. From the fit
generated structural model (SEM analysis), it was found that the
drivers of actual purchase behavior are collectivism, cultural
openness and patriotism; the drivers of intention to purchase
domestic product are attitude, control belief, collectivism and
conservatism; and drivers of ethnocentrism are cultural openness,
control belief, foreign travel and patriotism. It also shows that
Malaysian consumers scored high in ethnocentrism and patriotism.
The findings are discussed in the perspective of its implication to
Malaysian National Agenda.
Abstract: Activated carbons (M4P0, M4P2, and M5P2) used in
this research were produced from palm shell and polyetherether
ketone (PEEK) via carbonization, impregnation and microwave
activation. The adsorption/desorption process was carried out using
static volumetric adsorption. Regeneration is important in the overall
economy of the process and waste minimization. This work focuses
on the thermal regeneration of the CO2 exhausted microwave
activated carbons. The regeneration strategy adopted was thermal
with nitrogen purge desorption with N2 feed flow rate of 20 ml/min
for 1 h at atmospheric pressure followed by drying at 150oC.Seven
successive adsorption/regeneration processes were carried out on the
material. It was found that after seven adsorption regeneration cycles;
the regeneration efficiency (RE) for CO2 activated carbon from palm
shell only (M4P0) was more than 90% while that of hybrid palm
shell-PEEK (M4P2, M5P2) was above 95%. The cyclic adsorption
and regeneration shows the stability of the adsorbent materials.
Abstract: Recently, universities are increasingly consuming
energy to support various activities. A large population of staff and
students in Malaysian universities has led to excessive energy
consumption which directly gives an impact to the environment. The
key question then ascended “How well is an energy management
(EM) been practiced in universities without taking the Critical
Success Factors (CSFs) into consideration to ensure the management
of university achieves the goals in reducing energy consumption.
Review on past literature is carried out to establish CSFs for EM best
practices. Thus, this paper highlighted the CSFs which have to be
focused on by management of university to successfully measure the
EM implementation and its performance. At the end of this paper, a
theoretical framework is developed for EM success factors towards
sustainable university.
Abstract: The dielectric properties and ionic conductivity of
novel "ceramic state" polymer electrolytes for high capacity lithium
battery are characterized by Radio frequency and Microwave
methods in two broad frequency ranges from 50 Hz to 20 KHz and 4
GHz to 40 GHz. This innovative solid polymer electrolyte which is
highly ionic conductive (10-3 S/cm at room temperature) from -40oC
to +150oC can be used in any battery application. Such polymer
exhibits properties more like a ceramic rather than polymer. The
various applied measurement methods produced accurate dielectric
results for comprehensive analysis of electrochemical properties and
ion transportation mechanism of this newly invented polymer
electrolyte. Two techniques and instruments employing air gap
measurement by Capacitance Bridge and in-waveguide measurement
by vector network analyzer are applied to measure the complex
dielectric spectra. The complex dielectric spectra are used to
determine the complex alternating current electrical conductivity and
thus the ionic conductivity.