Abstract: In this paper a new maximum power point tracking
algorithm for photovoltaic arrays is proposed. The algorithm detects
the maximum power point of the PV. The computed maximum
power is used as a reference value (set point) of the control system.
ON/OFF power controller with hysteresis band is used to control the
operation of a Buck chopper such that the PV module always
operates at its maximum power computed from the MPPT algorithm.
The major difference between the proposed algorithm and other
techniques is that the proposed algorithm is used to control directly
the power drawn from the PV.
The proposed MPPT has several advantages: simplicity, high
convergence speed, and independent on PV array characteristics. The
algorithm is tested under various operating conditions. The obtained
results have proven that the MPP is tracked even under sudden
change of irradiation level.
Abstract: Multiple sequence alignment is a fundamental part in
many bioinformatics applications such as phylogenetic analysis.
Many alignment methods have been proposed. Each method gives a
different result for the same data set, and consequently generates a
different phylogenetic tree. Hence, the chosen alignment method
affects the resulting tree. However in the literature, there is no
evaluation of multiple alignment methods based on the comparison of
their phylogenetic trees. This work evaluates the following eight
aligners: ClustalX, T-Coffee, SAGA, MUSCLE, MAFFT, DIALIGN,
ProbCons and Align-m, based on their phylogenetic trees (test trees)
produced on a given data set. The Neighbor-Joining method is used
to estimate trees. Three criteria, namely, the dNNI, the dRF and the
Id_Tree are established to test the ability of different alignment
methods to produce closer test tree compared to the reference one
(true tree). Results show that the method which produces the most
accurate alignment gives the nearest test tree to the reference tree.
MUSCLE outperforms all aligners with respect to the three criteria
and for all datasets, performing particularly better when sequence
identities are within 10-20%. It is followed by T-Coffee at lower
sequence identity (30%), trees scores of all methods
become similar.
Abstract: This paper proposes transient angle stability
agents to enhance power system stability. The proposed transient
angle stability agents divided into two strategy agents. The
first strategy agent is a prediction agent that will predict power
system instability. According to the prediction agent-s output,
the second strategy agent, which is a control agent, is automatically
calculating the amount of active power reduction that can
stabilize the system and initiating a control action. The control
action considered is turbine fast valving. The proposed strategies
are applied to a realistic power system, the IEEE 50-
generator system. Results show that the proposed technique can
be used on-line for power system instability prediction and control.
Abstract: Films of pure tin oxide SnO2 and in presence of
antimony atoms (SnO2-Sb) deposited onto glass substrates have
shown a sufficiently high energy gap to be transparent in the visible
region, a high electrical mobility and a carrier concentration which
displays a good electrical conductivity [1]. In this work, the effects of
polycrystalline silicon substrate on the optical properties of pure and
Sb doped tin oxide is investigated.
We used the APCVD (atmospheric pressure chemical vapour
deposition) technique, which is a low-cost and simple technique,
under nitrogen ambient, for growing this material. A series of SnO2
and SnO2-Sb have been deposited onto polycrystalline silicon
substrates with different contents of antimony atoms at the same
conditions of deposition (substrate temperature, flow oxygen,
duration and nitrogen atmosphere of the reactor). The effect of the
substrate in terms of morphology and nonlinear optical properties,
mainly the reflectance, was studied. The reflectance intensity of the
device, compared to the reflectance of tin oxide films deposited
directly on glass substrate, is clearly reduced on the overall
wavelength range. It is obvious that the roughness of the poly-c
silicon plays an important role by improving the reflectance and
hence the optical parameters.
A clear shift in the minimum of the reflectance upon doping level
is observed. This minimum corresponds to strong free carrier
absorption, resulting in different plasma frequency. This effect is
followed by an increase in the reflectance depending of the antimony
doping. Applying the extended Drude theory to the combining
optical and electrical obtained results these effects are discussed.
Abstract: Embedded systems need to respect stringent real
time constraints. Various hardware components included in such
systems such as cache memories exhibit variability and therefore
affect execution time. Indeed, a cache memory access from an
embedded microprocessor might result in a cache hit where the
data is available or a cache miss and the data need to be fetched
with an additional delay from an external memory. It is therefore
highly desirable to predict future memory accesses during
execution in order to appropriately prefetch data without incurring
delays. In this paper, we evaluate the potential of several artificial
neural networks for the prediction of instruction memory
addresses. Neural network have the potential to tackle the nonlinear
behavior observed in memory accesses during program
execution and their demonstrated numerous hardware
implementation emphasize this choice over traditional forecasting
techniques for their inclusion in embedded systems. However,
embedded applications execute millions of instructions and
therefore millions of addresses to be predicted. This very
challenging problem of neural network based prediction of large
time series is approached in this paper by evaluating various neural
network architectures based on the recurrent neural network
paradigm with pre-processing based on the Self Organizing Map
(SOM) classification technique.
Abstract: In the present work an investigation of the effects of
the air frontal velocity, relative humidity and dry air temperature on
the heat transfer characteristics of plain finned tube evaporator has
been conducted. Using an appropriate correlation for the air side heat
transfer coefficient the temperature distribution along the fin surface
was calculated using a dimensionless temperature distribution. For a
constant relative humidity and bulb temperature, it is found that the
temperature distribution decreases with increasing air frontal
velocity. Apparently, it is attributed to the condensate water film
flowing over the fin surface. When dry air temperature and face
velocity are being kept constant, the temperature distribution
decreases with the increase of inlet relative humidity. An increase in
the inlet relative humidity is accompanied by a higher amount of
moisture on the fin surface. This results in a higher amount of latent
heat transfer which involves higher fin surface temperature. For the
influence of dry air temperature, the results here show an increase in
the dimensionless temperature parameter with a decrease in bulb
temperature. Increasing bulb temperature leads to higher amount of
sensible and latent heat transfer when other conditions remain
constant.
Abstract: The fortified of soft wheat flour with cowpea flour in
bread making was investigated. The Soft wheat flour (SWF) was
substituted by cowpea flour at levels of 5, 15 and 20%. The protein content of composite breads ranged from 6.1 – 9.9%. Significant
difference was observed in moisture, protein and crude fibre contents of control (wheat bread) and composite bread at 5% addition of
cowpea. Water absorption capacities of composite flours increased with increasing levels of cowpea flour in the blend. The specific loaf
volume decreased significantly with increased cowpea content of
blends. The overall acceptability of the 5% cowpea flour content of
composite bread was not significantly different from the control (Soft Wheat-bread) but there is significantly different with increasing the
levels of cowpea flour in the blend more than 5%.
Abstract: Unified Modeling Language (UML) extensions for real time embedded systems (RTES) co-design, are taking a growing interest by a great number of industrial and research communities. The extension mechanism is provided by UML profiles for RTES. It aims at improving an easily-understood method of system design for non-experts. On the other hand, one of the key items of the co- design methods is the Hardware/Software partitioning and scheduling tasks. Indeed, it is mandatory to define where and when tasks are implemented and run. Unfortunately the main goals of co-design are not included in the usual practice of UML profiles. So, there exists a need for mapping used models to an execution platform for both schedulability test and HW/SW partitioning. In the present work, test schedulability and design space exploration are performed at an early stage. The proposed approach adopts Model Driven Engineering MDE. It starts from UML specification annotated with the recent profile for the Modeling and Analysis of Real Time Embedded systems MARTE. Following refinement strategy, transformation rules allow to find a feasible schedule that satisfies timing constraints and to define where tasks will be implemented. The overall approach is experimented for the design of a football player robot application.
Abstract: Natural gas flow contains undesirable solid particles,
liquid condensation, and/or oil droplets and requires reliable
removing equipment to perform filtration. Recent natural gas
processing applications are demanded compactness and reliability of
process equipment. Since conventional means are sophisticated in
design, poor in efficiency, and continue lacking robust, a supersonic
nozzle has been introduced as an alternative means to meet such
demands.
A 3-D Convergent-Divergent Nozzle is simulated using
commercial Code for pressure ratio (NPR) varies from 1.2 to 2. Six
different shapes of nozzle are numerically examined to illustrate the
position of shock-wave as such spot could be considered as a
benchmark of particle separation. Rectangle, triangle, circular,
elliptical, pentagon, and hexagon nozzles are simulated using Fluent
Code with all have same cross-sectional area.
The simple one-dimensional inviscid theory does not describe the
actual features of fluid flow precisely as it ignores the impact of
nozzle configuration on the flow properties. CFD Simulation results,
however, show that nozzle geometry influences the flow structures
including location of shock wave.
The CFD analysis predicts shock appearance when p01/pa>1.2 for
almost all geometry and locates at the lower area ratio (Ae/At).
Simulation results showed that shock wave in Elliptical nozzle has
the farthest distance from the throat among the others at relatively
small NPR. As NPR increases, hexagon would be the farthest. The
numerical result is compared with available experimental data and
has shown good agreement in terms of shock location and flow
structure.
Abstract: This paper proposes a declarative language for
knowledge representation (Ibn Rochd), and its environment of
exploitation (DeGSE). This DeGSE system was designed and
developed to facilitate Ibn Rochd writing applications. The system
was tested on several knowledge bases by ascending complexity,
culminating in a system for recognition of a plant or a tree, and
advisors to purchase a car, for pedagogical and academic guidance,
or for bank savings and credit. Finally, the limits of the language and
research perspectives are stated.
Abstract: An experimental and numerical study has been conducted to clarify heat transfer characteristics and effectiveness of a cross-flow heat exchanger employing staggered wing-shaped tubes at different angels of attack. The water-side Rew and the air-side Rea were at 5 x 102 and at from 1.8 x 103 to 9.7 x 103, respectively. The tubes arrangements were employed with various angles of attack θ1,2,3 from 0° to 330° at the considered Rea range. Correlation of Nu, St, as well as the heat transfer per unit pumping power (ε) in terms of Rea, design parameters for the studied bundle were presented. The temperature fields around the staggered wing-shaped tubes bundle were predicted by using commercial CFD FLUENT 6.3.26 software package. Results indicated that the heat transfer was increased by increasing the angle of attack from 0° to 45°, while the opposite was true for angles of attack from 135° to 180°. The best thermal performance and hence η of studied bundle was occurred at the lowest Rea and/or zero angle of attack. Comparisons between the experimental and numerical results of the present study and those, previously, obtained for similar available studies showed good agreements.
Abstract: Endemic Artemia franciscana populations can be found throughout the American continent and also as an introduced specie in several country all over the world, such as in the Mediterranean region where Artemia franciscana was identified as an invasive specie replacing native Artemia parthenogenetica and Artemia salina. In the present study, the characterization of the new invasive Artemia franciscana reported from Sabkhet Halk El-Menzel (Tunisia) was done based on the cysts biometry, nauplii instar-I length, Adult sexual dimorphism and fatty acid profile. The mean value of the diameter of non-decapsulated and decapsulated cysts, chorion thickness and naupliar length is 235.8, 226.3, 4.75 and 426.8 μm, respectively. Sexual dimorphism for adults specimen showed that maximal distance between compound eyes, diameter for compound eyes, length of first antenna and the abdomen length compared to the total body length ratio, are the most important variables for males and females discrimination with a total contribution of 62.39 %. The analysis of fatty acid methyl esters profile of decapsulated cysts resulted in low levels of linolenic acid (LLA, C18:3n-3) and high levels of eicosapentaenoic acid (EPA, C20:5n-3) with 3.11 and 11.10 %, respectively. Low quantity of docosahexaenoic acid (DHA, 22:6n-3) was also observed with 0.17 mg.g-1 dry weight.
Abstract: Load forecasting has become in recent years one of the major areas of research in electrical engineering. Most traditional forecasting models and artificial intelligence neural network techniques have been tried out in this task. Artificial neural networks (ANN) have lately received much attention, and a great number of papers have reported successful experiments and practical tests. This article presents the development of an ANN-based short-term load forecasting model with improved generalization technique for the Regional Power Control Center of Saudi Electricity Company, Western Operation Area (SEC-WOA). The proposed ANN is trained with weather-related data and historical electric load-related data using the data from the calendar years 2001, 2002, 2003, and 2004 for training. The model tested for one week at five different seasons, typically, winter, spring, summer, Ramadan and fall seasons, and the mean absolute average error for one hour-ahead load forecasting found 1.12%.
Abstract: Numerous concrete structures projects are currently running in Libya as part of a US$50 billion government funding. The
quality of concrete used in 20 different construction projects were assessed based mainly on the concrete compressive strength achieved. The projects are scattered all over the country and are at
various levels of completeness. For most of these projects, the
concrete compressive strength was obtained from test results of a
150mm standard cube mold. Statistical analysis of collected concrete
compressive strengths reveals that the data in general followed a
normal distribution pattern. The study covers comparison and assessment of concrete quality aspects such as: quality control, strength range, data standard deviation, data scatter, and ratio of minimum strength to design strength. Site quality control for these projects ranged from very good to poor according to ACI214 criteria [1]. The ranges (Rg) of the strength (max. strength – min. strength) divided by average strength are from (34% to 160%). Data scatter is
measured as the range (Rg) divided by standard deviation () and is
found to be (1.82 to 11.04), indicating that the range is ±3σ.
International construction companies working in Libya follow
different assessment criteria for concrete compressive strength in lieu
of national unified procedure. The study reveals that assessments of
concrete quality conducted by these construction companies usually
meet their adopted (internal) standards, but sometimes fail to meet
internationally known standard requirements. The assessment of
concrete presented in this paper is based on ACI, British standards
and proposed Libyan concrete strength assessment criteria.
Abstract: The major urban centers are all facing rapid growth is
most often associated with spreading urbanization, social status of the
car has also changed: it has become a commodity of mass
consumption. There are currently about 5 million and 260 cars in
Algeria (2008), this number increases every year 200,000 new cars.
These phenomena induce a demand for greater mobility and a
significant need for transport infrastructure. Faced with these
problems and development of the growing use of the automobile,
central governments and local authorities in charge of urban transport
issues are aware of the need to develop their urban transport systems
but often lack opportunities.
Urban Transport Plans (PDU) were born in reaction to the "culture
of automobile." Their existence in the world the '80s, however, they
had little success before laws on air and rational use of energy in 90
years does not alter substantially their content and make mandatory
their implementation in cities of over 100,000 inhabitants (Abroad)
[1].
The objective of this work is to use the tool and specifically
Geomatics techniques as decision support in the organization and
management of travel while taking into consideration the influence,
which will then translate by National Urban Transport Plan.
Abstract: The requirements analysis, modeling, and simulation have consistently been one of the main challenges during the development of complex systems. The scenarios and the state machines are two successful models to describe the behavior of an interactive system. The scenarios represent examples of system execution in the form of sequences of messages exchanged between objects and are a partial view of the system. In contrast, state machines can represent the overall system behavior. The automation of processing scenarios in the state machines provide some answers to various problems such as system behavior validation and scenarios consistency checking. In this paper, we propose a method for translating scenarios in state machines represented by Discreet EVent Specification and procedure to detect implied scenarios. Each induced DEVS model represents the behavior of an object of the system. The global system behavior is described by coupling the atomic DEVS models and validated through simulation. We improve the validation process with integrating formal methods to eliminate logical inconsistencies in the global model. For that end, we use the Z notation.
Abstract: The reliability of distributed systems and computer
networks have been modeled by a probabilistic network or a graph G.
Computing the residual connectedness reliability (RCR), denoted by
R(G), under the node fault model is very useful, but is an NP-hard
problem. Since it may need exponential time of the network size to
compute the exact value of R(G), it is important to calculate its tight
approximate value, especially its lower bound, at a moderate
calculation time. In this paper, we propose an efficient algorithm for
reliability lower bound of distributed systems with unreliable nodes.
We also applied our algorithm to several typical classes of networks
to evaluate the lower bounds and show the effectiveness of our
algorithm.
Abstract: This paper presents a Particle Swarm Optimization
(PSO) method for determining the optimal parameters of a first-order
controller for TCP/AQM system. The model TCP/AQM is described
by a second-order system with time delay. First, the analytical
approach, based on the D-decomposition method and Lemma of
Kharitonov, is used to determine the stabilizing regions of a firstorder
controller. Second, the optimal parameters of the controller are
obtained by the PSO algorithm. Finally, the proposed method is
implemented in the Network Simulator NS-2 and compared with the
PI controller.
Abstract: The development of the signal compression
algorithms is having compressive progress. These algorithms are
continuously improved by new tools and aim to reduce, an average,
the number of bits necessary to the signal representation by means of
minimizing the reconstruction error. The following article proposes
the compression of Arabic speech signal by a hybrid method
combining the wavelet transform and the linear prediction. The
adopted approach rests, on one hand, on the original signal
decomposition by ways of analysis filters, which is followed by the
compression stage, and on the other hand, on the application of the
order 5, as well as, the compression signal coefficients. The aim of
this approach is the estimation of the predicted error, which will be
coded and transmitted. The decoding operation is then used to
reconstitute the original signal. Thus, the adequate choice of the
bench of filters is useful to the transform in necessary to increase the
compression rate and induce an impercevable distortion from an
auditive point of view.
Abstract: In a recent major industry-supported research and development study, a novel framework was developed and applied for assessment of reliability and quality performance levels in reallife power systems with practical large-scale sizes. The new assessment methodology is based on three metaphors (dimensions) representing the relationship between available generation capacities and required demand levels. The paper shares the results of the successfully completed stud and describes the implementation of the new methodology on practical zones in the Saudi electricity system.