Abstract: This paper presents the modeling and simulation of a hybrid proton exchange membrane fuel cell (PEMFC) with an energy storage system for use in a stand-alone distributed generation (DG) system. The simulation model consists of fuel cell DG, lead-acid battery, maximum power point tracking and power conditioning unit which is modeled in the MATLAB/Simulink platform. Poor loadfollowing characteristics and slow response to rapid load changes are some of the weaknesses of PEMFC because of the gas processing reaction and the fuel cell dynamics. To address the load-tracking issues in PEMFC, a hybrid PEMFC and battery storage system is considered and modelled. The model utilizes PEMFC as the main energy source whereas the battery functions as energy storage to compensate for the limitations of PEMFC.Simulation results are given to show the overall system performance under light and heavyloading conditions.
Abstract: In this study, a vibration analysis was carried out of
symmetric angle-ply laminated composite plates with and without
square hole when subjected to compressive loads, numerically. A
buckling analysis is also performed to determine the buckling load of
laminated plates. For each fibre orientation, the compression load is
taken equal to 50% of the corresponding buckling load. In the
analysis, finite element method (FEM) was applied to perform
parametric studies, the effects of degree of orthotropy and stacking
sequence upon the fundamental frequencies and buckling loads are
discussed. The results show that the presence of a constant
compressive load tends to reduce uniformly the natural frequencies
for materials which have a low degree of orthotropy. However, this
reduction becomes non-uniform for materials with a higher degree of
orthotropy.
Abstract: This research project aims to investigate difference in
relative rates concerning phosphoryl transfer relevant to biological
catalysis of DNA and RNA in the pH-independent reactions.
Activated Models of DNA and RNA for alkyl-aryl phosphate diesters
(with 4-nitrophenyl as a good leaving group) have successfully been
prepared to gather kinetic parameters. Eyring plots for the pH–
independent hydrolysis of 1 and 2 were established at different
temperatures in the range 100–160 °C. These measurements have
been used to provide a better estimate for the difference in relative
rates between the reactivity of DNA and RNA cleavage. Eyring plot
gave an extrapolated rate of kH2O = 1 × 10-10 s -1 for 1 (RNA model)
and 2 (DNA model) at 25°C. Comparing the reactivity of RNA
model and DNA model shows that the difference in relative rates in
the pH-independent reactions is surprisingly very similar at 25°. This
allows us to obtain chemical insights into how biological catalysts
such as enzymes may have evolved to perform their current
functions.
Abstract: Airbag deployment has been known to be responsible
for huge death, incidental injuries and broken bones due to low crash
severity and wrong deployment decisions. Therefore, the authorities
and industries have been looking for more innovative and intelligent
products to be realized for future enhancements in the vehicle safety
systems (VSSs). Although the VSSs technologies have advanced
considerably, they still face challenges such as how to avoid
unnecessary and untimely airbag deployments that can be hazardous
and fatal. Currently, most of the existing airbag systems deploy
without regard to occupant size and position. As such, this paper will
focus on the occupant and crash sensing performances due to frontal
collisions for the new breed of so called smart airbag systems. It
intends to provide a thorough discussion relating to the occupancy
detection, occupant size classification, occupant off-position
detection to determine safe distance zone for airbag deployment,
crash-severity analysis and airbag decision algorithms via a computer
modeling. The proposed system model consists of three main
modules namely, occupant sensing, crash severity analysis and
decision fusion. The occupant sensing system module utilizes the
weight sensor to determine occupancy, classify the occupant size,
and determine occupant off-position condition to compute safe
distance for airbag deployment. The crash severity analysis module is
used to generate relevant information pertinent to airbag deployment
decision. Outputs from these two modules are fused to the decision
module for correct and efficient airbag deployment action. Computer
modeling work is carried out using Simulink, Stateflow,
SimMechanics and Virtual Reality toolboxes.
Abstract: The chemistry of sulphone hydrazide has gained increase interest in both synthetic organic chemistry and biological fields and has considerable value. The therapeutic importance of these compounds is the attractive force to continue research in such a point. The present review covers the literature up to date for the synthesis, reactions and applications of such compounds.
Abstract: Cloud Computing has recently emerged as a
compelling paradigm for managing and delivering services over the
internet. The rise of Cloud Computing is rapidly changing the
landscape of information technology, and ultimately turning the longheld
promise of utility computing into a reality. As the development
of Cloud Computing paradigm is speedily progressing, concepts, and
terminologies are becoming imprecise and ambiguous, as well as
different technologies are interfering. Thus, it becomes crucial to
clarify the key concepts and definitions. In this paper, we present the
anatomy of Cloud Computing, covering its essential concepts,
prominent characteristics, its affects, architectural design and key
technologies. We differentiate various service and deployment
models. Also, significant challenges and risks need are tackled in
order to guarantee the long-term success of Cloud Computing. The
aim of this paper is to provide a better understanding of the anatomy
of Cloud Computing and pave the way for further research in this
area.
Abstract: Because nodes are usually battery-powered, the energy
presents a very scarce resource in wireless sensor networks. For this
reason, the design of medium access control had to take energy
efficiency as one of its hottest concerns. Accordingly, in order to
improve the energy performance of MAC schemes in wireless sensor
networks, several ways can be followed. In fact, some researchers try
to limit idle listening while others focus on mitigating overhearing
(i.e. a node can hear a packet which is destined to another node)
or reducing the number of the used control packets. We, in this
paper, propose a new hybrid MAC protocol termed ELE-MAC
(i.e. Energy Latency Efficient MAC). The ELE-MAC major design
goals are energy and latency efficiencies. It adopts less control
packets than SMAC in order to preserve energy. We carried out ns-
2 simulations to evaluate the performance of the proposed protocol.
Thus, our simulation-s results prove the ELE-MAC energy efficiency.
Additionally, our solution performs statistically the same or better
latency characteristic compared to adaptive SMAC.
Abstract: Hydrogen sulfide (H2S) is a very toxic gas that is produced in very large quantities in the oil and gas industry. It cannot be flared to the atmosphere and Claus process based gas plants are used to recover the sulfur and convert the hydrogen to water. In this paper, we present optical characterization of an atmospheric pressure microwave plasma torch for H2S dissociation into hydrogen and sulfur. The torch is operated at 2.45 GHz with power up to 2 kW. Three different gases can simultaneously be injected in the plasma torch. Visual imaging and optical emission spectroscopy are used to characterize the plasma for varying gas flow rates and microwave power. The plasma length, emission spectra and temperature are presented. The obtained experimental results validate our earlier published simulation results of plasma torch.
Abstract: Anaerobic digestion process is one of the alternative
methods to convert organic waste into methane gas which is a fuel
and energy source. Activities of various kinds of microorganisms are
the main factor for anaerobic digestion which produces methane gas.
Therefore, in this study a modified Anaerobic Baffled Reactor (ABR)
with working volume of 50 liters was designed to identify the
microorganisms through biogas production. The mixture of 75%
kitchen waste and 25% sewage sludge was used as substrate.
Observations on microorganisms in the ABR showed that there exists
a small amount of protozoa (5%) and fungi (2%) in the system, but
almost 93% of the microorganism population consists of bacteria. It
is definitely clear that bacteria are responsible for anaerobic
biodegradation of kitchen waste. Results show that in the
acidification zone of the ABR (front compartments of reactor) fast
growing bacteria capable of growth at high substrate levels and
reduced pH was dominant. A shift to slower growing scavenging
bacteria that grow better at higher pH was occurring towards the end
of the reactor. Due to the ability of activity in acetate environment the
percentages of Methanococcus, Methanosarcina and Methanotrix
were higher than other kinds of methane former in the system.
Abstract: During 2011 and 2012 seasons, Zaghloul date palms received four sprays of silicon (Si) at 0.05 to 0.1% and selenium (Se) at 0.01 to 0.02%. Growth, nutritional status, yield as well as physical and chemical characteristics of the fruits in response to application of silicon and selenium were investigated. Single and combined applications of silicon at 0.05 to 0.1% and selenium at 0.01 to 0.02% was very effective in enhancing the leaf area, total chlorophylls, percentages of N, P and K in the leaves, yield, bunch weight as well as physical and chemical characteristics of the fruits in relative to the check treatment. Silicon was superior to selenium in this respect. Combined application was favorable than using each alone in this connection. Treating Zaghloul date palms four times with a mixture of silicon at 0.05% + selenium at 0.01% resulted in an economical yield and producing better fruit quality.
Abstract: Source code retrieval is of immense importance in the software engineering field. The complex tasks of retrieving and extracting information from source code documents is vital in the development cycle of the large software systems. The two main subtasks which result from these activities are code duplication prevention and plagiarism detection. In this paper, we propose a Mohamed Amine Ouddan, and Hassane Essafi source code retrieval system based on two-level fingerprint representation, respectively the structural and the semantic information within a source code. A sequence alignment technique is applied on these fingerprints in order to quantify the similarity between source code portions. The specific purpose of the system is to detect plagiarism and duplicated code between programs written in different programming languages belonging to the same class, such as C, Cµ, Java and CSharp. These four languages are supported by the actual version of the system which is designed such that it may be easily adapted for any programming language.
Abstract: The main objective of the present paper is to derive an easy numerical technique for the analysis of the free vibration through the stepped regions of plates. Based on the utilities of the step by step integration initial values IV and Finite differences FD methods, the present improved Initial Value Finite Differences (IVFD) technique is achieved. The first initial conditions are formulated in convenient forms for the step by step integrations while the upper and lower edge conditions are expressed in finite difference modes. Also compatibility conditions are created due to the sudden variation of plate thickness. The present method (IVFD) is applied to solve the fourth order partial differential equation of motion for stepped plate across two different panels under the sudden step compatibility in addition to different types of end conditions. The obtained results are examined and the validity of the present method is proved showing excellent efficiency and rapid convergence.
Abstract: This work attempts to improve the permselectivity of poly-ortho-phenylenediamine (PPD) coating for glutamate biosensor applications on Pt microelectrode, using constant potential amperometry and cyclic voltammetry. Percentage permeability of the modified PPD microelectrode was carried out towards hydrogen peroxide (H2O2) and ascorbic acid (AA) whereas permselectivity represents the percentage interference by AA in H2O2 detection. The 50-μm diameter Pt disk microelectrode showed a good permeability value toward H2O2 (95%) and selectivity against AA (0.01%) compared to other sizes of electrode studied here. The electrode was further modified with glutamate oxidase (GluOx) that was immobilized and cross linked with glutaraldehyde (GA, 0.125%), resulting in Pt/PPD/GluOx-GA electrode design. The maximum current density Jmax and apparent Michaelis constant, KM, obtained on Pt/PPD/GluOx-GA electrodes were 48 μA cm-2 and 50 μM, respectively. The linear region slope (LRS) was 0.96 μA cm-2 mM-1. The detection limit (LOD) for glutamate was 3.0 ± 0.6 μM. This study shows a promising glutamate microbiosensor for brain glutamate detection.
Abstract: An Advance Driver Assistance System (ADAS) is a computer system on board a vehicle which is used to reduce the risk of vehicular accidents by monitoring factors relating to the driver, vehicle and environment and taking some action when a risk is identified. Much work has been done on assessing vehicle and environmental state but there is still comparatively little published work that tackles the problem of driver state. Visual attention is one such driver state. In fact, some researchers claim that lack of attention is the main cause of accidents as factors such as fatigue, alcohol or drug use, distraction and speeding all impair the driver-s capacity to pay attention to the vehicle and road conditions [1]. This seems to imply that the main cause of accidents is inappropriate driver behaviour in cases where the driver is not giving full attention while driving. The work presented in this paper proposes an ADAS system which uses an image based template matching algorithm to detect if a driver is failing to observe particular windscreen cells. This is achieved by dividing the windscreen into 24 uniform cells (4 rows of 6 columns) and matching video images of the driver-s left eye with eye-gesture templates drawn from images of the driver looking at the centre of each windscreen cell. The main contribution of this paper is to assess the accuracy of this approach using Receiver Operating Characteristic analysis. The results of our evaluation give a sensitivity value of 84.3% and a specificity value of 85.0% for the eye-gesture template approach indicating that it may be useful for driver point of regard determinations.
Abstract: This paper presents a new adaptive DMC controller
that improves the controller performance in case of plant-model
mismatch. The new controller monitors the plant measured output,
compares it with the model output and calculates weights applied to
the controller move. Simulations show that the new controller can
help improve control performance and avoid instability in case of
severe model mismatches.
Abstract: Atherosclerosis was identified as a chronic inflammatory process resulting from interactions between plasma lipoproteins, cellular components (monocyte, macrophages, T lymphocytes, endothelial cells and smooth muscle cells) and the extracellular matrix of the arterial wall. Several types of genes were known to express during formation of atherosclerosis. This study is carried out to identify unknown differentially expressed gene (DEG) in atherogenesis. Rabbit’s aorta tissues were stained by H&E for histomorphology. GeneFishing™ PCR analysis was performed from total RNA extracted from the aorta tissues. The DNA fragment from DEG was cloned, sequenced and validated by Real-time PCR. Histomorphology showed intimal thickening in the aorta. DEG detected from ACP-41 was identified as cathepsin B gene and showed upregulation at week-8 and week-12 of atherogenesis. Therefore, ACP-based GeneFishing™ PCR facilitated identification of cathepsin B gene which was differentially expressed during development of atherosclerosis.
Abstract: This paper presents the work of signal discrimination
specifically for Electrocardiogram (ECG) waveform. ECG signal is
comprised of P, QRS, and T waves in each normal heart beat to
describe the pattern of heart rhythms corresponds to a specific
individual. Further medical diagnosis could be done to determine any
heart related disease using ECG information. The emphasis on QRS
Complex classification is further discussed to illustrate the
importance of it. Pan-Tompkins Algorithm, a widely known
technique has been adapted to realize the QRS Complex
classification process. There are eight steps involved namely
sampling, normalization, low pass filter, high pass filter (build a band
pass filter), derivation, squaring, averaging and lastly is the QRS
detection. The simulation results obtained is represented in a
Graphical User Interface (GUI) developed using MATLAB.
Abstract: This paper presents a new approach for the prob-ability density function estimation using the Support Vector Ma-chines (SVM) and the Expectation Maximization (EM) algorithms.In the proposed approach, an advanced algorithm for the SVM den-sity estimation which incorporates the Mean Field theory in the learning process is used. Instead of using ad-hoc values for the para-meters of the kernel function which is used by the SVM algorithm,the proposed approach uses the EM algorithm for an automatic optimization of the kernel. Experimental evaluation using simulated data set shows encouraging results.
Abstract: This paper discusses the investigation of a wearable
textile monopole antenna on specific absorption rate (SAR) for bodycentric
wireless communication applications at 2.45 GHz. The
antenna is characterized on a realistic 8 x 8 x 8 mm3 resolution
truncated Hugo body model in CST Microwave Studio software. The
result exhibited that the simulated SAR values were reduced
significantly by 83.5% as the position of textile monopole was
varying between 0 mm and 15 mm away from the human upper arm.
A power absorption reduction of 52.2% was also noticed as the
distance of textile monopole increased.
Abstract: At the time where electronic books, or e-Books, offer
students a fun way of learning , teachers who are used to the paper
text books may find it as a new challenge to use it as a part of
learning process. Precisely, there are various types of e-Books
available to suit students- knowledge, characteristics, abilities, and
interests. The paper discusses teachers- perceptions on the use of ebooks
as a paper text book in the classroom. A survey was conducted
on 72 teachers who use e-books as textbooks. It was discovered that a
majority of these teachers had good perceptions on the use of ebooks.
However, they had little problems using the devices. It can be
overcome with some strategies and a suggested framework.