Abstract: A factorial design of experiments and a response surface methodology were implemented to investigate the liquid-liquid extraction process of zinc (II) from acetate medium using the 1-Butyl-imidazolium di(2-ethylhexyl) phosphate [BIm+][D2EHP-]. The optimization process of extraction parameters such as the initial pH effect (2.5, 4.5, and 6.6), ionic liquid concentration (1, 5.5, and 10 mM) and salt effect (0.01, 5, and 10 mM) was carried out using a three-level full factorial design (33). The results of the factorial design demonstrate that all these factors are statistically significant, including the square effects of pH and ionic liquid concentration. The results showed that the order of significance: IL concentration > salt effect > initial pH. Analysis of variance (ANOVA) showing high coefficient of determination (R2 = 0.91) and low probability values (P < 0.05) signifies the validity of the predicted second-order quadratic model for Zn (II) extraction. The optimum conditions for the extraction of zinc (II) at the constant temperature (20 °C), initial Zn (II) concentration (1mM) and A/O ratio of unity were: initial pH (4.8), extractant concentration (9.9 mM), and NaCl concentration (8.2 mM). At the optimized condition, the metal ion could be quantitatively extracted.
Abstract: Despite all the hype about green building, many developers are still resistant to the idea of building green due to the common perception that green building construction is expensive. This contradicts with scholarly findings that identify only a marginal cost premium or none at all given that green design is considered during the design process and planning stage. Nevertheless, cost implications continue to become an issue when deciding to build green. The planning stage is of strategic importance as decisions made at this early stage would influence the project cost thereafter. Using analysis of existing literature, the paper identifies six elements of soft cost that are considered in the planning stage. The elements include consultants, green building consultant, certification, commissioning, market, and tax. Out of the six elements, commissioning represents the bulk of soft cost for buildings seeking green certification. The study concluded that, although hard cost may have a bigger impact on the project cost, but soft cost is the hidden cost which people tend to ignore. Poor consideration of soft cost during planning stage may lead to over-realistic expectations and ultimately, overlooked cost additions.
Abstract: The goal of this paper is to examine the effects of laser
radiation on the skin wound healing using infrared thermography as
non-invasive method for the monitoring of the skin temperature
changes during laser treatment. Thirty Wistar rats were used in this
study. A skin lesion was performed at the leg on all rats. The animals
were exposed to laser radiation (λ = 670 nm, P = 15 mW, DP = 16.31
mW/cm2) for 600 s. Thermal images of wound were acquired before
and after laser irradiation. The results have demonstrated that the
tissue temperature decreases from 35.5±0.50°C in the first treatment
day to 31.3±0.42°C after the third treatment day. This value is close
to the normal value of the skin temperature and indicates the end of
the skin repair process. In conclusion, the improvements in the
wound healing following exposure to laser radiation have been
revealed by infrared thermography.
Abstract: The objective of this project is to study the corrosion
behaviour and hardness based on the presence of martensite in dual
phase steel. This study was conducted on six samples of dual phase
steel which have different percentage of martensite. A total of 9
specimens were prepared by intercritical annealing process to study
the effect of temperature to the formation of martensite. The low
carbon steels specimens were heated for 25 minutes in a specified
temperature ranging from 7250C to 8250C followed by rapid cooling
in water. The measurement of corrosion rate was done by using
extrapolation tafel method, while potentiostat was used to control and
measured the current produced. This measurement is performed
through a system named CMS105. The result shows that a specimen
with higher percentage of martensite is likely to corrode faster.
Hardness test for each specimen was conducted to compare its
hardness with low carbon steel. The results obtained indicate that the
specimen hardness is proportional to the amount of martensite in dual
phase steel.
Abstract: Careful design and selection of daylighting systems can greatly help in reducing not only artificial lighting use, but also decrease cooling energy consumption and, therefore, potential for downsizing air-conditioning systems. This paper aims to evaluate the energy performance of two types of top-light daylighting systems due to the integration of daylight together with artificial lighting in an existing examinaton hall in University Kebangsaan Malaysia, based on a hot and humid climate. Computer simulation models have been created for building case study (base case) and the two types of toplight daylighting designs for building energy performance evaluation using the VisualDOE 4.0 building energy simulation program. The finding revealed that daylighting through top-light systems is a very beneficial design strategy in reducing annual lighting energy consumption and the overall total annual energy consumption.
Abstract: Discretization of spatial derivatives is an important
issue in meshfree methods especially when the derivative terms
contain non-linear coefficients. In this paper, various methods used
for discretization of second-order spatial derivatives are investigated
in the context of Smoothed Particle Hydrodynamics. Three popular
forms (i.e. "double summation", "second-order kernel derivation",
and "difference scheme") are studied using one-dimensional unsteady
heat conduction equation. To assess these schemes, transient response
to a step function initial condition is considered. Due to parabolic
nature of the heat equation, one can expect smooth and monotone
solutions. It is shown, however in this paper, that regardless of
the type of kernel function used and the size of smoothing radius,
the double summation discretization form leads to non-physical
oscillations which persist in the solution. Also, results show that when
a second-order kernel derivative is used, a high-order kernel function
shall be employed in such a way that the distance of inflection
point from origin in the kernel function be less than the nearest
particle distance. Otherwise, solutions may exhibit oscillations near
discontinuities unlike the "difference scheme" which unconditionally
produces monotone results.
Abstract: Technology transfer is a common method for
companies to acquire new technology and presents both challenges
and substantial benefits. In some cases especially in developing
countries, the mere possession of technology does not guarantee a
competitive advantage if the appropriate infrastructure is not in place.
In this paper, we identify the localization factors needed to provide a
better understanding of the conditions necessary for localization in
order to benefit from future technology developments. Our
theoretical and empirical analyses allow us to identify several factors
in the technology transfer process that affect localization and provide
leverage in enhancing capabilities and absorptive capacity.The
impact factors are categorized within different groups of government,
firms, institutes and market, and are verified through the empirical
survey of a technology transfer experience. Moreover, statistical
analysis has allowed a deeper understanding of the importance of
each factor and has enabled each group to prioritize their
organizational policies to effectively localize their technology.
Abstract: The experimental design was 4 x 5 factorial with three
replications in fully controlled research greenhouse in Department of
Soil Sciences and Plant Nutrition, Faculty of Agriculture, University
of Selcuk in the year of 2009. Determination of tolerant chickpea
genotypes to drought was made in the research. Additionally,
sophisticated effects of drought on plant growth and development,
biochemical and physical properties or physical defense mechanisms
were presented. According to the results, the primary genotypes were
Ilgın YP (0.0063 g/gh) for leaf water capacity, 22235 70.44(%) for
relative water content, 22159 (82.47%) for real water content,
22159 (5.03 mg/l) for chlorophyll a+b, Ilgın YP (125.89 nmol
H2O2.dak-1/ mg protein-1) for peroxidase, Yunak YP (769.67
unit/ mg protein-1) for superoxide dismutase, Seydişehir YP
(16.74 μg.TA-1) for proline, Gökçe (80.01 nmol H2O2.dak-1/ mg
protein-1) for catalase. Consequently, all the genotypes
increased their enzyme activity depending on the increasing of
drought stress consider with the effects of drought stress on leaf
enzyme activity. Chickpea genotypes are increasing enzyme
activity against to drought stress.
Abstract: With the popularity of the multi-core and many-core architectures there is a great requirement for software frameworks which can support parallel programming methodologies. In this paper we introduce an Eclipse toolkit, JConqurr which is easy to use and provides robust support for flexible parallel progrmaming. JConqurr is a multi-core and many-core programming toolkit for Java which is capable of providing support for common parallel programming patterns which include task, data, divide and conquer and pipeline parallelism. The toolkit uses an annotation and a directive mechanism to convert the sequential code into parallel code. In addition to that we have proposed a novel mechanism to achieve the parallelism using graphical processing units (GPU). Experiments with common parallelizable algorithms have shown that our toolkit can be easily and efficiently used to convert sequential code to parallel code and significant performance gains can be achieved.
Abstract: In this paper, a new approach is introduced to solve
Blasius equation using parameter identification of a nonlinear
function which is used as approximation function. Bees Algorithm
(BA) is applied in order to find the adjustable parameters of
approximation function regarding minimizing a fitness function
including these parameters (i.e. adjustable parameters). These
parameters are determined how the approximation function has to
satisfy the boundary conditions. In order to demonstrate the
presented method, the obtained results are compared with another
numerical method. Present method can be easily extended to solve a
wide range of problems.
Abstract: The current sheath dynamics in plasma focus facilities
is the most important factors. In this paper the current sheath velocity
at three dimensional with Sahand plasma focus facility is
investigated. For this purpose the discharge is produced in argon gas
with deposited energy lying in the range of 20-37kJ. The current
sheath is monitored using two tridimensional magnetic probes. These
probes installed near the surface of the interior electrode (anode) at
125mm from the anode axis (pinch place). The effect of gas pressure
on the current sheath velocity also is investigated.
Abstract: This paper deals with the application of a fuzzy set in
measuring teachers- beliefs about mathematics. The vagueness of
beliefs was transformed into standard mathematical values using a
fuzzy preferences model. The study employed a fuzzy approach
questionnaire which consists of six attributes for measuring
mathematics teachers- beliefs about mathematics. The fuzzy conjoint
analysis approach based on fuzzy set theory was used to analyze the
data from twenty three mathematics teachers from four secondary
schools in Terengganu, Malaysia. Teachers- beliefs were recorded in
form of degrees of similarity and its levels of agreement. The
attribute 'Drills and practice is one of the best ways of learning
mathematics' scored the highest degree of similarity at 0. 79860 with
level of 'strongly agree'. The results showed that the teachers- beliefs
about mathematics were varied. This is shown by different levels of
agreement and degrees of similarity of the measured attributes.
Abstract: We study the dynamic response of a wind turbine
structure subjected to theoretical seismic motions, taking into account
the rotational component of ground shaking. Models are generated
for a shallow moderate crustal earthquake in the Madrid Region
(Spain). Synthetic translational and rotational time histories are
computed using the Discrete Wavenumber Method, assuming a point
source and a horizontal layered earth structure. These are used to
analyze the dynamic response of a wind turbine, represented by a
simple finite element model. Von Mises stress values at different
heights of the tower are used to study the dynamical structural
response to a set of synthetic ground motion time histories
Abstract: An experimental study is presented on the effect of
Conservation Agriculture (CA) compared to Conventional
Agriculture (ConvA) upon Maize Yield based on split-plot model.
Two factors have been considered: A Factor-Fertilization with two
variants: A1- N40P40 kg/ha and A2- N90P70 kg/ha; B Factor- Crop
protection with 4 variants : B1- 4 treatments, B2-3 treatments, B3- 2
treatments and B4- 1 treatment. In comparison with conventional
agriculture, CA determined lower maize yields. Fertilization is the
key factor determining a yield gain of 973.58 kg/ha in ConvA and
1,123.33 kg/ha in CA. A reduced number of treatments determined a
yield decline. The A-B interaction had a positive effect on maize
yield when a larger amount of fertilizer and 4 or 3 treatments were
applied in ConvA and a benefic in CA for highest fertilization level
and 2 treatments. The B2A2 ConvA variant was the most efficient
leading to 302.67 kg/ha gain while B3A2 CA variant brought 181.33
kg production gain.
Abstract: In this paper, an analytical approach is used to study the coupled lateral-torsional vibrations of laminated composite beam. It is known that in such structures due to the fibers orientation in various layers, any lateral displacement will produce a twisting moment. This phenomenon is modeled by the bending-twisting material coupling rigidity and its main feature is the coupling of lateral and torsional vibrations. In addition to the material coupling, the effects of shear deformation and rotary inertia are taken into account in the definition of the potential and kinetic energies. Then, the governing differential equations are derived using the Hamilton-s principle and the mathematical model matches the Timoshenko beam model when neglecting the effect of bending-twisting rigidity. The equations of motion which form a system of three coupled PDEs are solved analytically to study the free vibrations of the beam in lateral and rotational modes due to the bending, as well as the torsional mode caused by twisting. The analytic solution is carried out in three steps: 1) assuming synchronous motion for the kinematic variables which are the lateral, rotational and torsional displacements, 2) solving the ensuing eigenvalue problem which contains three coupled second order ODEs and 3) imposing different boundary conditions related to combinations of simply, clamped and free end conditions. The resulting natural frequencies and mode shapes are compared with similar results in the literature and good agreement is achieved.
Abstract: There are many problems associated with the World Wide
Web: getting lost in the hyperspace; the web content is still accessible only
to humans and difficulties of web administration. The solution to these
problems is the Semantic Web which is considered to be the extension
for the current web presents information in both human readable and
machine processable form. The aim of this study is to reach new
generic foundation architecture for the Semantic Web because there
is no clear architecture for it, there are four versions, but still up to
now there is no agreement for one of these versions nor is there a
clear picture for the relation between different layers and
technologies inside this architecture. This can be done depending on
the idea of previous versions as well as Gerber-s evaluation method
as a step toward an agreement for one Semantic Web architecture.
Abstract: Elastic light single-scattering spectroscopy system
with a single optical fiber probe was employed to differentiate cancerous prostate tissue from non-cancerous prostate tissue ex-vivo just after radical prostatectomy. First, ELSSS spectra were acquired
from cancerous prostate tissue to define its spectral features. Then,
spectra were acquired from normal prostate tissue to define difference in spectral features between the cancerous and normal
prostate tissues. Of the total 66 tissue samples were evaluated from
nine patients by ELSSS system. Comparing of histopathology results
and ELSSS measurements revealed that sign of the spectral slopes of
cancerous prostate tissue is negative and non-cancerous tissue is positive in the wavelength range from 450 to 750 nm. Based on the
correlation between histopathology results and sign of the spectral
slopes, ELSSS system differentiates cancerous prostate tissue from
non- cancerous with a sensitivity of 0.95 and a specificity of 0.94.
Abstract: A judicious choice of insert material, tool geometry and
cutting conditions can make hard turning produce better surfaces than
grinding. In the present study, an attempt has been made to
investigate the effect of cutting tool materials on cutting forces (feed
force, thrust force and cutting force) in finish hard turning of AISI
D2 cold work tool steel. In conclusion of the results obtained with a
constant depth of cut and feed rate, it is important to note that cutting
force is directly affected by cutting tool material.
Abstract: Nanostructured materials have attracted many
researchers due to their outstanding mechanical and physical
properties. For example, carbon nanotubes (CNTs) or carbon
nanofibres (CNFs) are considered to be attractive reinforcement
materials for light weight and high strength metal matrix composites.
These composites are being projected for use in structural
applications for their high specific strength as well as functional
materials for their exciting thermal and electrical characteristics. The
critical issues of CNT-reinforced MMCs include processing
techniques, nanotube dispersion, interface, strengthening mechanisms
and mechanical properties. One of the major obstacles to the effective
use of carbon nanotubes as reinforcements in metal matrix
composites is their agglomeration and poor distribution/dispersion
within the metallic matrix. In order to tap into the advantages of the
properties of CNTs (or CNFs) in composites, the high dispersion of
CNTs (or CNFs) and strong interfacial bonding are the key issues
which are still challenging. Processing techniques used for synthesis
of the composites have been studied with an objective to achieve
homogeneous distribution of carbon nanotubes in the matrix.
Modified mechanical alloying (ball milling) techniques have emerged
as promising routes for the fabrication of carbon nanotube (CNT)
reinforced metal matrix composites. In order to obtain a
homogeneous product, good control of the milling process, in
particular control of the ball movement, is essential. The control of
the ball motion during the milling leads to a reduction in grinding
energy and a more homogeneous product. Also, the critical inner
diameter of the milling container at a particular rotational speed can
be calculated. In the present work, we use conventional and modified
mechanical alloying to generate a homogenous distribution of 2 wt.
% CNT within Al powders. 99% purity Aluminium powder (Acros,
200mesh) was used along with two different types of multiwall
carbon nanotube (MWCNTs) having different aspect ratios to
produce Al-CNT composites. The composite powders were processed
into bulk material by compaction, and sintering using a cylindrical
compaction and tube furnace. Field Emission Scanning electron
microscopy (FESEM), X-Ray diffraction (XRD), Raman
spectroscopy and Vickers macro hardness tester were used to
evaluate CNT dispersion, powder morphology, CNT damage, phase
analysis, mechanical properties and crystal size determination.
Despite the success of ball milling in dispersing CNTs in Al powder,
it is often accompanied with considerable strain hardening of the Al
powder, which may have implications on the final properties of the
composite. The results show that particle size and morphology vary
with milling time. Also, by using the mixing process and sonication
before mechanical alloying and modified ball mill, dispersion of the
CNTs in Al matrix improves.
Abstract: Evaporator is an important and widely used heat
exchanger in air conditioning and refrigeration industries. Different
methods have been used by investigators to increase the heat transfer
rates in evaporators. One of the passive techniques to enhance heat
transfer coefficient is the application of microfin tubes. The
mechanism of heat transfer augmentation in microfin tubes is
dependent on the flow regime of two-phase flow. Therefore many
investigations of the flow patterns for in-tube evaporation have been
reported in literatures. The gravitational force, surface tension and
the vapor-liquid interfacial shear stress are known as three dominant
factors controlling the vapor and liquid distribution inside the tube. A
review of the existing literature reveals that the previous
investigations were concerned with the two-phase flow pattern for
flow boiling in horizontal tubes [12], [9]. Therefore, the objective of
the present investigation is to obtain information about the two-phase
flow patterns for evaporation of R-134a inside horizontal smooth and
microfin tubes. Also Investigation of heat transfer during flow
boiling of R-134a inside horizontal microfin and smooth tube have
been carried out experimentally The heat transfer coefficients for
annular flow in the smooth tube is shown to agree well with Gungor
and Winterton-s correlation [4]. All the flow patterns occurred in the
test can be divided into three dominant regimes, i.e., stratified-wavy
flow, wavy-annular flow and annular flow. Experimental data are
plotted in two kinds of flow maps, i.e., Weber number for the vapor
versus weber number for the liquid flow map and mass flux versus
vapor quality flow map. The transition from wavy-annular flow to
annular or stratified-wavy flow is identified in the flow maps.