Abstract: Calcium [Ca2+] is an important second messenger
which plays an important role in signal transduction. There are
several parameters that affect its concentration profile like buffer
source etc. The effect of stationary immobile buffer on Ca2+
concentration has been incorporated which is a very important
parameter needed to be taken into account in order to make the
model more realistic. Interdependence of all the important parameters
like diffusion coefficient and influx over [Ca2+] profile has been
studied. Model is developed in the form of advection diffusion
equation together with buffer concentration. A program has been
developed using finite volume method for the entire problem and
simulated on an AMD-Turion 32-bit machine to compute the
numerical results.
Abstract: A fast adaptive Tomlinson Harashima (T-H) precoder structure is presented for indoor wireless communications, where the channel may vary due to rotation and small movement of the mobile terminal. A frequency-selective slow fading channel which is time-invariant over a frame is assumed. In this adaptive T-H precoder, feedback coefficients are updated at the end of every uplink frame by using system identification technique for channel estimation in contrary with the conventional T-H precoding concept where the channel is estimated during the starting of the uplink frame via Wiener solution. In conventional T-H precoder it is assumed the channel is time-invariant in both uplink and downlink frames. However assuming the channel is time-invariant over only one frame instead of two, the proposed adaptive T-H precoder yields better performance than conventional T-H precoder if the channel is varied in uplink after receiving the training sequence.
Abstract: This paper discusses the approach of real-time
controlling of the energy management system using the data
acquisition tool of LabVIEW. The main idea of this inspiration was
to interface the Station (PC) with the system and publish the data on
internet using LabVIEW. In this venture, controlling and switching of
3 phase AC loads are effectively and efficiently done. The phases are
also sensed through devices. In case of any failure the attached
generator starts functioning automatically. The computer sends
command to the system and system respond to the request. The
modern feature is to access and control the system world-wide using
world wide web (internet). This controlling can be done at any time
from anywhere to effectively use the energy especially in developing
countries where energy management is a big problem. In this system
totally integrated devices are used to operate via remote location.
Abstract: Estimation of stature is an important step in developing a biological profile for human identification. It may provide a valuable indicator for unknown individual in a population. The aim of this study was to analyses the relationship between stature and lower limb dimensions in the Malaysian population. The sample comprised 100 corpses, which included 69 males and 31 females between age ranges of 20 to 90 years old. The parameters measured were stature, thigh length, lower leg length, leg length, foot length, foot height and foot breadth. Results showed that mean values in males were significantly higher than those in females (P < 0.05). There were significant correlations between lower limb dimensions and stature. Cross-validation of the equation on 100 individuals showed close approximation between known stature and estimated stature. It was concluded that lower limb dimensions were useful for estimation of stature, which should be validated in future studies.
Abstract: Probability-based identity disclosure risk
measurement may give the same overall risk for different
anonymization strategy of the same dataset. Some entities in the
anonymous dataset may have higher identification risks than the
others. Individuals are more concerned about higher risks than the
average and are more interested to know if they have a possibility of
being under higher risk. A notation of overall risk in the above
measurement method doesn-t indicate whether some of the involved
entities have higher identity disclosure risk than the others. In this
paper, we have introduced an identity disclosure risk measurement
method that not only implies overall risk, but also indicates whether
some of the members have higher risk than the others. The proposed
method quantifies the overall risk based on the individual risk values,
the percentage of the records that have a risk value higher than the
average and how larger the higher risk values are compared to the
average. We have analyzed the disclosure risks for different
disclosure control techniques applied to original microdata and
present the results.
Abstract: The fixed partial dentures are mainly used in the frontal
part of the dental arch because of their great esthetics. There are
several factors that are associated with the stress state created in
ceramic restorations, including: thickness of ceramic layers,
mechanical properties of the materials, elastic modulus of the
supporting substrate material, direction, magnitude and frequency of
applied load, size and location of occlusal contact areas, residual
stresses induced by processing or pores, restoration-cement
interfacial defects and environmental defects. The purpose of this
study is to evaluate the capability of Polarization Sensitive Optical
Coherence Tomography (PSOCT) in detection and analysis of
possible material defects in metal-ceramic and integral ceramic fixed
partial dentures. As a conclusion, it is important to have a non
invasive method to investigate fixed partial prostheses before their
insertion in the oral cavity in order to satisfy the high stress
requirements and the esthetic function.
Abstract: GSM has undoubtedly become the most widespread
cellular technology and has established itself as one of the most
promising technology in wireless communication. The next
generation of mobile telephones had also become more powerful and
innovative in a way that new services related to the user-s location
will arise. Other than the 911 requirements for emergency location
initiated by the Federal Communication Commission (FCC) of the
United States, GSM positioning can be highly integrated in cellular
communication technology for commercial use. However, GSM
positioning is facing many challenges. Issues like accuracy,
availability, reliability and suitable cost render the development and
implementation of GSM positioning a challenging task. In this paper,
we investigate the optimal mobile position tracking means. We
employ an innovative scheme by integrating the Kalman filter in the
localization process especially that it has great tracking
characteristics. When tracking in two dimensions, Kalman filter is
very powerful due to its reliable performance as it supports
estimation of past, present, and future states, even when performing
in unknown environments. We show that enhanced position tracking
results is achieved when implementing the Kalman filter for GSM
tracking.
Abstract: Regenerative gas turbine engine cycle is presented that yields higher cycle efficiencies than simple cycle operating under the same conditions. The power output, efficiency and specific fuel consumption are simulated with respect to operating conditions. The analytical formulae about the relation to determine the thermal efficiency are derived taking into account the effected operation conditions (ambient temperature, compression ratio, regenerator effectiveness, compressor efficiency, turbine efficiency and turbine inlet temperature). Model calculations for a wide range of parameters are presented, as are comparisons with simple gas turbine cycle. The power output and thermal efficiency are found to be increasing with the regenerative effectiveness, and the compressor and turbine efficiencies. The efficiency increased with increase the compression ratio to 5, then efficiency decreased with increased compression ratio, but in simple cycle the thermal efficiency always increase with increased in compression ratio. The increased in ambient temperature caused decreased thermal efficiency, but the increased in turbine inlet temperature increase thermal efficiency.
Abstract: This paper explores the opportunity of using tri-axial
wireless accelerometers for supervised monitoring of sports
movements. A motion analysis system for the upper extremities of
lawn bowlers in particular is developed. Accelerometers are placed
on parts of human body such as the chest to represent the shoulder
movements, the back to capture the trunk motion, back of the hand,
the wrist and one above the elbow, to capture arm movements. These
sensors placement are carefully designed in order to avoid restricting
bowler-s movements. Data is acquired from these sensors in soft-real
time using virtual instrumentation; the acquired data is then
conditioned and converted into required parameters for motion
regeneration. A user interface was also created to facilitate in the
acquisition of data, and broadcasting of commands to the wireless
accelerometers. All motion regeneration in this paper deals with the
motion of the human body segment in the X and Y direction, looking
into the motion of the anterior/ posterior and lateral directions
respectively.
Abstract: Mathematical and computational modeling of calcium
signalling in nerve cells has produced considerable insights into how
the cells contracts with other cells under the variation of biophysical
and physiological parameters. The modeling of calcium signaling in
astrocytes has become more sophisticated. The modeling effort has
provided insight to understand the cell contraction. Main objective
of this work is to study the effect of voltage gated (Operated)
calcium channel (VOC) on calcium profile in the form of advection
diffusion equation. A mathematical model is developed in the form
of advection diffusion equation for the calcium profile. The model
incorporates the important physiological parameter like diffusion
coefficient etc. Appropriate boundary conditions have been framed.
Finite volume method is employed to solve the problem. A program
has been developed using in MATLAB 7.5 for the entire problem
and simulated on an AMD-Turion 32-bite machine to compute the
numerical results.
Abstract: The various applications of VLSI circuits in highperformance
computing, telecommunications, and consumer
electronics has been expanding progressively, and at a very hasty
pace. This paper describes a new model for partitioning a circuit
using DBSCAN and fuzzy ARTMAP neural network. The first step
is concerned with feature extraction, where we had make use
DBSCAN algorithm. The second step is the classification and is
composed of a fuzzy ARTMAP neural network. The performance of
both approaches is compared using benchmark data provided by
MCNC standard cell placement benchmark netlists. Analysis of the
investigational results proved that the fuzzy ARTMAP with
DBSCAN model achieves greater performance then only fuzzy
ARTMAP in recognizing sub-circuits with lowest amount of
interconnections between them The recognition rate using fuzzy
ARTMAP with DBSCAN is 97.7% compared to only fuzzy
ARTMAP.
Abstract: Scaffolds play a key role in tissue engineering and can be produced in many different ways depending on the applications and the materials used. Most researchers used an experimental trialand- error approach into new biomaterials but computer simulation applied to tissue engineering can offer a more exhaustive approach to test and screen out biomaterials. This paper develops the model of scaffolds and Computational Fluid Dynamics that show the value of computer simulations in determining the influence of the geometrical scaffold parameter porosity, pore size and shape on the permeability of scaffolds, magnitude of velocity, drop pressure, shear stress distribution and level and the proper design of the geometry of the scaffold. This creates a need for more advanced studies that include aspects of dynamic conditions of a micro fluid passing through the scaffold were characterized for tissue engineering applications and differentiation of tissues within scaffolds.
Abstract: Nowadays, quick technological changes force companies
to develop innovative products in an increasingly competitive
environment. Therefore, how to enhance the time of new product
development is very important. This design problem often lacks
the exact formula for getting it, and highly depends upon human
designers- past experiences. For these reasons, in this work, a Casebased
reasoning (CBR) system to assist in new product development
is proposed. When a case is recovered from the case base, the system
will take into account not only the attribute-s specific value and
how important it is. It will also take into account if the attribute
has a positive influence over the product development. Hence the
manufacturing time will be improved. This information will be
introduced as a new concept called “adaptability". An application to
this method for hearing instrument new design illustrates the proposed
approach.
Abstract: To model the human visual system (HVS) in the region of interest, we propose a new objective metric evaluation adapted to wavelet foveation-based image compression quality measurement, which exploits a foveation setup filter implementation technique in the DWT domain, based especially on the point and region of fixation of the human eye. This model is then used to predict the visible divergences between an original and compressed image with respect to this region field and yields an adapted and local measure error by removing all peripheral errors. The technique, which we call foveation wavelet visible difference prediction (FWVDP), is demonstrated on a number of noisy images all of which have the same local peak signal to noise ratio (PSNR), but visibly different errors. We show that the FWVDP reliably predicts the fixation areas of interest where error is masked, due to high image contrast, and the areas where the error is visible, due to low image contrast. The paper also suggests ways in which the FWVDP can be used to determine a visually optimal quantization strategy for foveation-based wavelet coefficients and to produce a quantitative local measure of image quality.
Abstract: In this paper we propose a Particle Swarm heuristic
optimized Multi-Antenna (MA) system. Efficient MA systems
detection is performed using a robust stochastic evolutionary
computation algorithm based on movement and intelligence of
swarms. This iterative particle swarm optimized (PSO) detector
significantly reduces the computational complexity of conventional
Maximum Likelihood (ML) detection technique. The simulation
results achieved with this proposed MA-PSO detection algorithm
show near optimal performance when compared with ML-MA
receiver. The performance of proposed detector is convincingly
better for higher order modulation schemes and large number of
antennas where conventional ML detector becomes non-practical.
Abstract: The objective of this study is to determine the thermal comfort among worker at Malaysian automotive industry. One critical manual assembly workstation had been chosen as a subject for the study. The human subjects for the study constitute operators at Body Assembly Station of the factory. The environment examined was the Relative Humidity (%), Airflow (m/s), Air Temperature (°C) and Radiant Temperature (°C) of the surrounding workstation area. The environmental factors were measured using Babuc apparatus, which is capable to measure simultaneously those mentioned environmental factors. The time series data of fluctuating level of factors were plotted to identify the significant changes of factors. Then thermal comfort of the workers were assessed by using ISO Standard 7730 Thermal sensation scale by using Predicted Mean Vote (PMV). Further Predicted percentage dissatisfied (PPD) is used to estimate the thermal comfort satisfaction of the occupant. Finally the PPD versus PMV were plotted to present the thermal comfort scenario of workers involved in related workstation. The result of PMV at the related industry is between 1.8 and 2.3, where PPD at that building is between 60% to 84%. The survey result indicated that the temperature more influenced comfort to the occupants
Abstract: Interactive web-based computer simulations are
needed by the medical community to replicate the experience of
surgical procedures as closely and realistically as possible without
the need to practice on corpses, animals and/or plastic models. In this
paper, we offer a review on current state of the research on
simulations of surgical threads, identify future needs and present our
proposed plans to meet them. Our goal is to create a physics-based
simulator, which will predict the behavior of surgical thread when
subjected to conditions commonly encountered during surgery. To
that end, we will i) develop three dimensional finite element models
based on the Cosserat theory of elasticity ii) test and feedback results
with the medical community and iii) develop a web-based user
interface to run/command our simulator and visualize the results. The
impacts of our research are that i) it will contribute to the
development of a new generation of training for medical school
students and ii) the simulator will be useful to expert surgeons in
developing new, better and less risky procedures.
Abstract: Authentication plays a vital role in many secure
systems. Most of these systems require user to log in with his or her
secret password or pass phrase before entering it. This is to ensure all
the valuables information is kept confidential guaranteeing also its
integrity and availability. However, to achieve this goal, users are
required to memorize high entropy passwords or pass phrases.
Unfortunately, this sometimes causes difficulty for user to remember
meaningless strings of data. This paper presents a new scheme which
assigns a weight to each personal question given to the user in
revealing the encrypted secrets or password. Concentration of this
scheme is to offer fault tolerance to users by allowing them to forget
the specific password to a subset of questions and still recover the
secret and achieve successful authentication. Comparison on level of
security for weight-based and weightless secret recovery scheme is
also discussed. The paper concludes with the few areas that requires
more investigation in this research.
Abstract: In this paper, an alternating implicit block method for
solving two dimensional scalar wave equation is presented. The
new method consist of two stages for each time step implemented
in alternating directions which are very simple in computation. To
increase the speed of computation, a group of adjacent points is
computed simultaneously. It is shown that the presented method
increase the maximum time step size and more accurate than the
conventional finite difference time domain (FDTD) method and other
existing method of natural ordering.
Abstract: Climate change and environmental pressures are
major international issues nowadays. It is time when governments,
businesses and consumers have to respond through more
environmentally friendly and aware practices, products and policies.
This is the prime time to develop alternative sustainable construction
materials, reduce greenhouse gas emissions, save energy, look to
renewable energy sources and recycled materials, and reduce waste.
The utilization of waste materials (slag, fly ash, glass beads, plastic
and so on) in concrete manufacturing is significant due to its
engineering, financial, environmental and ecological benefits. Thus,
utilization of waste materials in concrete production is very much
helpful to reach the goal of the sustainable construction. Therefore,
this study intends to use glass beads in concrete production.
The paper reports on the performance of 9 different concrete
mixes containing different ratios of glass crushed to 5 mm - 20 mm
maximum size and glass marble of 20 mm size as coarse aggregate.
Ordinary Portland cement type 1 and fine sand less than 0.5 mm were
used to produce standard concrete cylinders. Compressive strength
tests were carried out on concrete specimens at various ages. Test
results indicated that the mix having the balanced ratio of glass beads
and round marbles possess maximum compressive strength which is
3889 psi, as glass beads perform better in bond formation but have
lower strength, on the other hand marbles are strong in themselves
but not good in bonding. These mixes were prepared following a
specific W/C and aggregate ratio; more strength can be expected to
achieve from different W/C, aggregate ratios, adding admixtures like
strength increasing agents, ASR inhibitor agents etc.