Abstract: The purpose of the experiments described in this article was the comparison of integrated fixed film activated sludge (IFAS) and activated sludge (AS) system. The IFAS applied system consists of the cigarette filter rods (wasted filter in tobacco factories) as a biofilm carrier. The comparison with activated sludge was performed by two parallel treatment lines. Organic substance, ammonia and TP removal was investigated over four month period. Synthetic wastewater was prepared with ordinary tap water and glucose as the main sources of carbon and energy, plus balanced macro and micro nutrients. COD removal percentages of 94.55%, and 81.62% were achieved for IFAS and activated sludge system, respectively. Also, ammonia concentration significantly decreased by increasing the HRT in both systems. The average ammonia removal of 97.40 % and 96.34% were achieved for IFAS and activated sludge system, respectively. The removal efficiency of total phosphorus (TP-P) was 60.64%, higher than AS process by 56.63% respectively.
Abstract: Self-compacting concrete (SCC), a new kind of high
performance concrete (HPC) have been first developed in Japan in
1986. The development of SCC has made casting of dense
reinforcement and mass concrete convenient, has minimized noise.
Fresh self-compacting concrete (SCC) flows into formwork and
around obstructions under its own weight to fill it completely and
self-compact (without any need for vibration), without any
segregation and blocking. The elimination of the need for
compaction leads to better quality concrete and substantial
improvement of working conditions. SCC mixes generally have a
much higher content of fine fillers, including cement, and produce
excessively high compressive strength concrete, which restricts its
field of application to special concrete only. To use SCC mixes in
general concrete construction practice, requires low cost materials to
make inexpensive concrete.
Rice husk ash (RHA) has been used as a highly reactive
pozzolanic material to improve the microstructure of the interfacial
transition zone (ITZ) between the cement paste and the aggregate in
self compacting concrete. Mechanical experiments of RHA blended
Portland cement concretes revealed that in addition to the pozzolanic
reactivity of RHA (chemical aspect), the particle grading (physical
aspect) of cement and RHA mixtures also exerted significant
influences on the blending efficiency.
The scope of this research was to determine the usefulness of Rice
husk ash (RHA) in the development of economical self compacting
concrete (SCC). The cost of materials will be decreased by reducing
the cement content by using waste material like rice husk ash instead
of.
This paper presents a study on the development of Mechanical
properties up to 180 days of self compacting and ordinary concretes
with rice-husk ash (RHA), from a rice paddy milling industry in
Rasht (Iran). Two different replacement percentages of cement by
RHA, 10%, and 20%, and two different water/cementicious material
ratios (0.40 and 0.35), were used for both of self compacting and
normal concrete specimens. The results are compared with those of
the self compacting concrete without RHA, with compressive,
flexural strength and modulus of elasticity. It is concluded that RHA
provides a positive effect on the Mechanical properties at age after
60 days.
Base of the result self compacting concrete specimens have higher
value than normal concrete specimens in all test except modulus of
elasticity. Also specimens with 20% replacement of cement by RHA
have the best performance.
Abstract: Recently, distributed generation technologies have received much attention for the potential energy savings and reliability assurances that might be achieved as a result of their widespread adoption. Fueling the attention have been the possibilities of international agreements to reduce greenhouse gas emissions, electricity sector restructuring, high power reliability requirements for certain activities, and concern about easing transmission and distribution capacity bottlenecks and congestion. So it is necessary that impact of these kinds of generators on distribution feeder reconfiguration would be investigated. This paper presents an approach for distribution reconfiguration considering Distributed Generators (DGs). The objective function is summation of electrical power losses A Tabu search optimization is used to solve the optimal operation problem. The approach is tested on a real distribution feeder.
Abstract: The purpose of this study is to introduce a new
interface program to calculate a dose distribution with Monte Carlo method in complex heterogeneous systems such as organs or tissues
in proton therapy. This interface program was developed under
MATLAB software and includes a friendly graphical user interface
with several tools such as image properties adjustment or results display. Quadtree decomposition technique was used as an image
segmentation algorithm to create optimum geometries from Computed Tomography (CT) images for dose calculations of proton
beam. The result of the mentioned technique is a number of nonoverlapped
squares with different sizes in every image. By this way
the resolution of image segmentation is high enough in and near
heterogeneous areas to preserve the precision of dose calculations
and is low enough in homogeneous areas to reduce the number of
cells directly. Furthermore a cell reduction algorithm can be used to combine neighboring cells with the same material. The validation of this method has been done in two ways; first, in comparison with experimental data obtained with 80 MeV proton beam in Cyclotron
and Radioisotope Center (CYRIC) in Tohoku University and second, in comparison with data based on polybinary tissue calibration method, performed in CYRIC. These results are presented in this paper. This program can read the output file of Monte Carlo code while region of interest is selected manually, and give a plot of dose distribution of proton beam superimposed onto the CT images.
Abstract: The steady-state operation of maintaining voltage
stability is done by switching various controllers scattered all over
the power network. When a contingency occurs, whether forced or
unforced, the dispatcher is to alleviate the problem in a minimum
time, cost, and effort. Persistent problem may lead to blackout. The
dispatcher is to have the appropriate switching of controllers in terms
of type, location, and size to remove the contingency and maintain
voltage stability. Wrong switching may worsen the problem and that
may lead to blackout. This work proposed and used a Fuzzy CMeans
Clustering (FCMC) to assist the dispatcher in the decision
making. The FCMC is used in the static voltage stability to map
instantaneously a contingency to a set of controllers where the types,
locations, and amount of switching are induced.
Abstract: In this paper delamination phenomenon in
Carbon-Epoxy laminated composite material is investigated
numerically. Arcan apparatus and specimen is modeled in ABAQUS
finite element software for different loading conditions and crack
geometries. The influence of variation of crack geometry on
interlaminar fracture stress intensity factor and energy release rate for
various mixed mode ratios and pure mode I and II was studied. Also,
correction factors for this specimen for different crack length ratios
were calculated. The finite element results indicate that for loading
angles close to pure mode-II loading, a high ratio of mode-II to
mode-I fracture is dominant and there is an opposite trend for loading
angles close to pure mode-I loading. It confirms that by varying the
loading angle of Arcan specimen pure mode-I, pure mode-II and a
wide range of mixed-mode loading conditions can be created and
tested. Also, numerical results confirm that the increase of the mode-
II loading contribution leads to an increase of fracture resistance in
the CF/PEI composite (i.e., a reduction in the total strain energy
release rate) and the increase of the crack length leads to a reduction
of interlaminar fracture resistance in the CF/PEI composite (i.e., an
increase in the total interlaminar strain energy release rate).
Abstract: In this paper, a watermarking algorithm that uses the wavelet transform with Multiple Description Coding (MDC) and Quantization Index Modulation (QIM) concepts is introduced. Also, the paper investigates the role of Contourlet Transform (CT) versus Wavelet Transform (WT) in providing robust image watermarking. Two measures are utilized in the comparison between the waveletbased and the contourlet-based methods; Peak Signal to Noise Ratio (PSNR) and Normalized Cross-Correlation (NCC). Experimental results reveal that the introduced algorithm is robust against different attacks and has good results compared to the contourlet-based algorithm.
Abstract: This paper deals optimized model to investigate the
effects of peak current, pulse on time and pulse off time in EDM performance on material removal rate of titanium alloy utilizing copper tungsten as electrode and positive polarity of the electrode. The experiments are carried out on Ti6Al4V. Experiments were
conducted by varying the peak current, pulse on time and pulse off time. A mathematical model is developed to correlate the influences of these variables and material removal rate of workpiece. Design of
experiments (DOE) method and response surface methodology
(RSM) techniques are implemented. The validity test of the fit and adequacy of the proposed models has been carried out through
analysis of variance (ANOVA). The obtained results evidence that as
the material removal rate increases as peak current and pulse on time
increases. The effect of pulse off time on MRR changes with peak ampere. The optimum machining conditions in favor of material removal rate are verified and compared. The optimum machining
conditions in favor of material removal rate are estimated and verified with proposed optimized results. It is observed that the developed model is within the limits of the agreeable error (about
4%) when compared to experimental results. This result leads to desirable material removal rate and economical industrial machining to optimize the input parameters.
Abstract: This paper tries to study the effect of geosynthetic inclusion on the improvement of the load-settlement characters of two layered soil. In addition, the effect of geogrid and geotextile in reduction of the required thickness of subbase layer in unpaved roads is studied. Considering the vast application of bearing ratio tests in road construction projects, this test is used in present investigation. Bearing ratio tests were performed on two layered soil including a granular soil layer at the top (as the subbase layer) and a weak clayey soil placed at the bottom (as the subgrade layer). These tests were performed for different conditions including unreinforced and reinforced by geogrid and geotextile and three thicknesses for top layer soil (subbase layer). In the reinforced condition the reinforcing element was placed on the interface of the top granular layer and the beneath clayey layer to study the separation effect of geosynthetics. In all tests the soils (both granular and clayey soil layers) were compacted according to optimum water content. At the end, the diagrams were plotted and were compared with each other. Furthermore, a comparison between geogrids and geotextiles behaviors on two layer soil is done in this paper. The results show an increase in compression strength of reinforced specimen in comparison with unreinforced soil sample. The effect of geosynthetic inclusion reduces by increasing the subbase thickness. In addition it was found that geogrids have more desirable behavior rather than geotextiles due to interlocking with the subbase layer aggregates.
Abstract: The nickel and gold nanoclusters as supported
catalysts were analyzed by XAS, XRD and XPS in order to
determine their local, global and electronic structure. The present
study has pointed out a strong deformation of the local structure of
the metal, due to its interaction with oxide supports. The average
particle size, the mean squares of the microstrain, the particle size
distribution and microstrain functions of the supported Ni and Au
catalysts were determined by XRD method using Generalized Fermi
Function for the X-ray line profiles approximation. Based on EXAFS
analysis we consider that the local structure of the investigated
systems is strongly distorted concerning the atomic number pairs.
Metal-support interaction is confirmed by the shape changes of the
probability densities of electron transitions: Ni K edge (1s →
continuum and 2p), Au LIII-edge (2p3/2 → continuum, 6s, 6d5/2 and
6d3/2). XPS investigations confirm the metal-support interaction at
their interface.
Abstract: This paper presents a web based remote access
microcontroller laboratory. Because of accelerated development in
electronics and computer technologies, microcontroller-based devices
and appliances are found in all aspects of our daily life. Before the
implementation of remote access microcontroller laboratory an
experiment set is developed by teaching staff for training
microcontrollers. Requirement of technical teaching and industrial
applications are considered when experiment set is designed.
Students can make the experiments by connecting to the experiment
set which is connected to the computer that set as the web server. The
students can program the microcontroller, can control digital and
analog inputs and can observe experiment. Laboratory experiment
web page can be accessed via www.elab.aku.edu.tr address.
Abstract: High Voltage (HV) transmission lines are widely
spread around residential places. They take all forms of shapes:
concrete, steel, and timber poles. Earth grid always form part of the
HV transmission structure, whereat soil resistivity value is one of the
main inputs when it comes to determining the earth grid
requirements. In this paper, the soil structure and its implication on
the electrode resistance of HV transmission poles will be explored. In
Addition, this paper will present simulation for various soil structures
using IEEE and Australian standards to verify the computation with
CDEGS software. Furthermore, the split factor behavior under
different soil resistivity structure will be presented using CDEGS
simulations.
Abstract: In this paper a way of hiding text message (Steganography) in the gray image has been presented. In this method tried to find binary value of each character of text message and then in the next stage, tried to find dark places of gray image (black) by converting the original image to binary image for labeling each object of image by considering on 8 connectivity. Then these images have been converted to RGB image in order to find dark places. Because in this way each sequence of gray color turns into RGB color and dark level of grey image is found by this way if the Gary image is very light the histogram must be changed manually to find just dark places. In the final stage each 8 pixels of dark places has been considered as a byte and binary value of each character has been put in low bit of each byte that was created manually by dark places pixels for increasing security of the main way of steganography (LSB).
Abstract: Response to the public health-related emergencies is analysed here for a rural university in South Africa. The structure of the designated emergency plan covers all the phases of the disaster management cycle. The plan contains elements of the vulnerability model and the technocratic model of emergency management. The response structures are vertically and horizontally integrated, while the planning contains elements of scenario-based and functional planning. The available number of medical professionals at the Rhodes University, along with the medical insurance rates, makes the staff and students potentially more medically vulnerable than the South African population. The main improvements of the emergency management are required in the tornado response and the information dissemination during health emergencies. The latter should involve the increased use of social media and e-mails, following the Taylor model of communication. Infrastructure must be improved in the telecommunication sector in the face of unpredictable electricity outages.
Abstract: Novel Coconut oil nanofluids of various concentrations have been prepared through ultrasonically assisted sol-gel method. The structural and morphological properties of the copper oxide nanoparticle have been analyzed with respectively and it revealed the monoclinic end-centered structure of crystallite and shuttle like flake morphology of agglomerates. Ultrasonic studies have been made for the nanofluids at different temperatures. The molecular interactions responsible for the changes in acoustical parameter with respect to concentration and temperature are discussed.
Abstract: The objective of this paper is to study the electrical
resistivity complexity between field and laboratory measurement, in
order to improve the effectiveness of data interpretation for
geophysical ground resistivity survey. The geological outcrop in
Penang, Malaysia with an obvious layering contact was chosen as the
study site. Two dimensional geoelectrical resistivity imaging were
used in this study to maps the resistivity distribution of subsurface,
whereas few subsurface sample were obtained for laboratory
advance. In this study, resistivity of samples in original conditions is
measured in laboratory by using time domain low-voltage technique,
particularly for granite core sample and soil resistivity measuring set
for soil sample. The experimentation results from both schemes are
studied, analyzed, calibrated and verified, including basis and
correlation, degree of tolerance and characteristics of substance.
Consequently, the significant different between both schemes is
explained comprehensively within this paper.
Abstract: Analytical solution of the first-order and third-order
shear deformation theories are developed to study the free vibration
behavior of simply supported functionally graded plates. The
material properties of plate are assumed to be graded in the thickness
direction as a power law distribution of volume fraction of the
constituents. The governing equations of functionally graded plates
are established by applying the Hamilton's principle and are solved
by using the Navier solution method. The influence of side-tothickness
ratio and constituent of volume fraction on the natural
frequencies are studied. The results are validated with the known
data in the literature.
Abstract: Phishing scheme is a new emerged security issue of
E-Commerce Crime in globalization. In this paper, the legal scaffold
of Malaysia, United States and United Kingdom are analyzed and
followed by discussion on critical issues that rose due to phishing
activities. The result revealed that inadequacy of current legal
framework is the main challenge to govern this epidemic. However,
lack of awareness among consumers, crisis on merchant-s
responsibility and lack of intrusion reports and incentive arrangement
contributes to phishing proliferating. Prevention is always better than
curb. By the end of this paper, some best practices for consumers and
corporations are suggested.
Abstract: The main aim of this work is to develop a model of hydrogen sulfide (H2S) separation from natural gas by using membrane separation technology. The model is developed by incorporating three diffusion mechanisms which are Knudsen, viscous and surface diffusion towards membrane selectivity and permeability. The findings from the simulation result shows that the permeability of the gas is dependent toward the pore size of the membrane, operating pressure, operating temperature as well as feed composition. The permeability of methane has the highest value for Poly (1-trimethylsilyl-1-propyne ) PTMSP membrane at pore size of 0.1nm and decreasing toward a minimum peak at pore range 1 to 1.5 nm as pore size increased before it increase again for pore size is greater than 1.5 nm. On the other hand, the permeability of hydrogen sulfide is found to increase almost proportionally with the increase of membrane pore size. Generally, the increase of pressure will increase the permeability of gas since more driving force is provided to the system while increasing of temperature would decrease the permeability due to the surface diffusion drop off effect. A corroboration of the simulation result also showed a good agreement with the experimental data.
Abstract: Real-time object tracking is a problem which involves extraction of critical information from complex and uncertain imagedata. In this paper, we present a comprehensive methodology to design an artificial neural network (ANN) for a real-time object tracking application. The object, which is tracked for the purpose of demonstration, is a specific airplane. However, the proposed ANN can be trained to track any other object of interest. The ANN has been simulated and tested on the training and testing datasets, as well as on a real-time streaming video. The tracking error is analyzed with post-regression analysis tool, which finds the correlation among the calculated coordinates and the correct coordinates of the object in the image. The encouraging results from the computer simulation and analysis show that the proposed ANN architecture is a good candidate solution to a real-time object tracking problem.