Abstract: In the stadium structure, the significant dynamic
responses such as resonance or similar behavior can be occurred by
spectator rhythmical activities. Thus, accurate analysis and precise
investigation of stadium structure that is subjected to dynamic loads
are required for practical design and serviceability check of stadium
structures. Moreover, it is desirable to measure and analyze the
dynamic loads of spectator activities because these dynamic loads can
not be easily expressed in numerical formula. In this study, various
dynamic loads induced by spectator movements are measured and
analyzed. These dynamic loads induced by spectators movement of
stadium structure can be classified into the impact load and the
periodic load. These dynamic loads can be expressed as Fourier
harmonic load. And, these dynamic loads could be applied for the
accurate vibration analysis of a stadium structure.
Abstract: As a simple to method estimate the plant heating energy
capacity of an apartment complex, a new load calculation method has
been proposed. The method which can be called as unit building
method, predicts the heating load of the entire complex instead of
summing up that of each apartment belonging to complex.
Comparison of the unit heating load for various floor sizes between the
present method and conventional approach shows a close agreement
with dynamic load calculation code. Some additional calculations are
performed to demonstrate it-s application examples.
Abstract: In this paper, we analyzed the pattern of urban spatial structure of Siheung City that had been divided into two parts and presented alternative plans in order to get rid of these phenomena. Concerning patterns of urban spatial structure, we examined it through means of analyzing status of land use, population density and distribution of residence, status of distribution of main facilities, medical facilities, status of distribution of cultural facilities, distribution of land prices and traffic volume trends. The results of study revealed that status of facilities distribution and distribution of land prices, etc. were bisected by the surrounding area of former municipal office and the district of Sihwa, which were both regarded as one apex of the city divide, forming a duo-centric city. In order to get rid of this problem concerned with urban spatial structure that has been bisected, it is required that measures in order to expand facilities in Siheung City should be taken.
Abstract: The purpose of this study was to examine the viewpoints in terms of changing distances and levels and thereby, comparatively analyze the visual sensitivity to the elements of the natural views. The questionnaire survey was conducted separately for experts and non-experts. Summing up, it was confirmed that the visual sensitivity to the elements of the same natural views differed significantly depending on subjects' professionalism, changes of the viewpoint levels and distances, while the visual sensitivity to 'openness of visual/view axes' did not differ significantly when only the distances of the viewpoints were varied. In addition, the visual sensitivity to visual/view axes differed between experts and ordinary people when the levels of the viewpoints were varied, while the visual sensitivity to 'damaged natural view resources' differed between two groups when the distances of the viewpoints were varied.
Abstract: In this paper, we proposed a method to reduce
quantization error. In order to reduce quantization error, low pass
filtering is applied on neighboring samples of current block in
H.264/AVC. However, it has a weak point that low pass filtering is
performed regardless of prediction direction. Since it doesn-t consider
prediction direction, it may not reduce quantization error effectively.
Proposed method considers prediction direction for low pass filtering
and uses a threshold condition for reducing flag bit. We compare our
experimental result with conventional method in H.264/AVC and we
can achieve the average bit-rate reduction of 1.534% by applying the
proposed method. Bit-rate reduction between 0.580% and 3.567% are
shown for experimental results.
Abstract: This study proposes a novel recommender system to
provide the advertisements of context-aware services. Our proposed
model is designed to apply a modified collaborative filtering (CF)
algorithm with regard to the several dimensions for the personalization
of mobile devices – location, time and the user-s needs type. In
particular, we employ a classification rule to understand user-s needs
type using a decision tree algorithm. In addition, we collect primary
data from the mobile phone users and apply them to the proposed
model to validate its effectiveness. Experimental results show that the
proposed system makes more accurate and satisfactory advertisements
than comparative systems.
Abstract: This paper presents an effective method for detecting vehicles in front of the camera-assisted car during nighttime driving. The proposed method detects vehicles based on detecting vehicle headlights and taillights using techniques of image segmentation and clustering. First, to effectively extract spotlight of interest, a segmentation process based on automatic multi-level threshold method is applied on the road-scene images. Second, to spatial clustering vehicle of detecting lamps, a grouping process based on light tracking and locating vehicle lighting patterns. For simulation, we are implemented through Da-vinci 7437 DSP board with near infrared mono-camera and tested it in the urban and rural roads. Through the test, classification performances are above 97% of true positive rate evaluated on real-time environment. Our method also has good performance in the case of clear, fog and rain weather.
Abstract: This study aims to investigate how much both son and
daughter trust their father and what are the underlying reasons they
trust their father. The results revealed five main reasons why
Malaysian adolescents trust their father. Those reasons are related to
the role of father, father-child relationship, father-s characteristics,
father-s nurturing nature and father-s attitude and behavior. A total of
1022 students (males = 241, females = 781) from one of public
university in Sabah, Malaysia participated in the study. The
participants completed open-ended questionnaires developed by Kim
(2008), asking how much the adolescents trust their father, and the
reasons why they trust their father. The data was analysed by using
the indigenous psychology method proposed by [1] Findings of this
study revealed the pattern of trust towards father for both Malaysian
male and female adolescents. The results contributed new
information about Malaysian adolescents- trust towards their father
form the indigenous context. The implications of finding will be
discussed.
Abstract: In manufacturing industries, development of measurement leads to increase the number of monitoring variables and eventually the importance of multivariate control comes to the fore. Statistical process control (SPC) is one of the most widely used as multivariate control chart. Nevertheless, SPC is restricted to apply in processes because its assumption of data as following specific distribution. Unfortunately, process data are composed by the mixture of several processes and it is hard to estimate as one certain distribution. To alternative conventional SPC, therefore, nonparametric control chart come into the picture because of the strength of nonparametric control chart, the absence of parameter estimation. SVDD based control chart is one of the nonparametric control charts having the advantage of flexible control boundary. However,basic concept of SVDD has been an oversight to the important of data characteristic, density distribution. Therefore, we proposed DW-SVDD (Density Weighted SVDD) to cover up the weakness of conventional SVDD. DW-SVDD makes a new attempt to consider dense of data as introducing the notion of density Weight. We extend as control chart using new proposed SVDD and a simulation study of various distributional data is conducted to demonstrate the improvement of performance.
Abstract: The fault current levels through the electric devices
have a significant impact on failure probability. New fault current
results in exceeding the rated capacity of circuit breaker and switching
equipments and changes operation characteristic of overcurrent relay.
In order to solve these problems, SFCL (Superconducting Fault
Current Limiter) has rising as one of new alternatives so as to improve
these problems. A fault current reduction differs depending on
installed location. Therefore, a location of SFCL is very important.
Also, SFCL decreases the fault current, and it prevents surrounding
protective devices to be exposed to fault current, it then will bring a
change of reliability. In this paper, we propose method which
determines the optimal location when SFCL is installed in power
system. In addition, the reliability about the power system which
SFCL was installed is evaluated. The efficiency and effectiveness of
this method are also shown by numerical examples and the reliability
indices are evaluated in this study at each load points. These results
show a reliability change of a system when SFCL was installed.
Abstract: Recordings from recent earthquakes have provided evidence that ground motions in the near field of a rupturing fault differ from ordinary ground motions, as they can contain a large energy, or “directivity" pulse. This pulse can cause considerable damage during an earthquake, especially to structures with natural periods close to those of the pulse. Failures of modern engineered structures observed within the near-fault region in recent earthquakes have revealed the vulnerability of existing RC buildings against pulse-type ground motions. This may be due to the fact that these modern structures had been designed primarily using the design spectra of available standards, which have been developed using stochastic processes with relatively long duration that characterizes more distant ground motions. Many recently designed and constructed buildings may therefore require strengthening in order to perform well when subjected to near-fault ground motions. Fiber Reinforced Polymers are considered to be a viable alternative, due to their relatively easy and quick installation, low life cycle costs and zero maintenance requirements. The objective of this paper is to investigate the adequacy of Artificial Neural Networks (ANN) to determine the three dimensional dynamic response of FRP strengthened RC buildings under the near-fault ground motions. For this purpose, one ANN model is proposed to estimate the base shear force, base bending moments and roof displacement of buildings in two directions. A training set of 168 and a validation set of 21 buildings are produced from FEA analysis results of the dynamic response of RC buildings under the near-fault earthquakes. It is demonstrated that the neural network based approach is highly successful in determining the response.
Abstract: This paper presents an iterative algorithm to find a
inverse kinematic solution of 5-DOF robot. The algorithm is to
minimize the iteration number. Since the 5-DOF robot cannot give full
orientation of tool. Only z-direction of tool is satisfied while rotation
of tool is determined by kinematic constraint. This work therefore
described how to specify the tool direction and let the tool rotation free.
The simulation results show that this algorithm effectively worked.
Using the proposed iteration algorithm, error due to inverse kinematics
converged to zero rapidly in 5 iterations. This algorithm was applied in
real welding robot and verified through various practical works.
Abstract: Firstly, research and development on RFID focuses on
manufacturing and retail sectors, because it can improve supply chain
efficiency. But, now a variety of field is considered the next research
area for Radio Frequency Identification (RFID). Although RFID is
infancy, RFID technology has great potential in power industry to
significantly reduce cost, and improve quality of power supply. To
complement the limitation of RFID, we adopt the WSN (Wireless
Sensor Network) technology. However, relevant experience is limited,
the challenge will be to derive requirement from business practice and
to determine whether it is possible or not. To explore this issue, we
conduct a case study on implementing power facility management
system using RFID/WSN in Korea Electric Power Corporation
(KEPCO). In this paper we describe requirement from power industry.
And we introduce design and implementation of the test bed.
Abstract: The top-heavy demographic of low birth-rate and longer lifespan is a growing social problem, and one of its expected effects will be a shortage of young workers and a growing reliance on a workforce of middle-aged and older people. However, the environment of today's industrial workplace is not particularly suited to middle-aged and older workers, one notable problem being temperature control. Higher temperatures can cause health problems such as heat stroke, and the number of cases increases sharply in people over 65. Moreover, in conditions above 33°C, older people can develop circulatory system disorders, and also have a higher chance of suffering a fatal heart attack. We therefore propose a new method for controlling temperature in the indoor workplace. In this study two different verification experiments were conducted, with the proposed temperature control method being tested in cargo containers and conventional houses. The method's effectiveness was apparent in measurements of temperature and electricity consumption
Abstract: The increasing number of senior population gradually
causes to demand the use of information and communication
technology for their satisfactory lives. This paper presents the
development of an integrated TV based system which offers an
opportunity to provide value added services to a large number of
elderly citizens, and thus helps improve their quality of life. The
design philosophy underlying this paper is to fulfill both technological
and human aspects. The balance between these two dimensions has
been currently stressed as a crucial element for the design of usable
systems in real use, particularly to the elderly who have physical and
mental decline. As the first step to achieve it, we have identified
human and social factors that affect the elder-s quality of life by a
literature review, and based on them, build four fundamental services:
information, healthcare, learning and social network services.
Secondly, the system architecture, employed technologies and the
elderly-friendly system design considerations are presented. This
reflects technological and human perspectives in terms of the system
design. Finally, we describe some scenarios that illustrate the
potentiality of the proposed system to improve elderly people-s quality
of life.
Abstract: The purpose of this research was develop a biological
nutrient removal (BNR) system which has low energy consumption, sludge production, and land usage. These indicate that BNR system could be a alternative of future wastewater treatment in ubiquitous
city(U-city). Organics and nitrogen compounds could be removed by this system so that secondary or tertiary stages of wastewater treatment satisfy their standards. This system was composed of oxic and anoxic
filter filed with PVDC and POM media. Anoxic/oxic filter system operated under empty bed contact time of 4 hours by increasing
recirculation ratio from 0 to 100 %. The system removals of total nitrogen and COD were 76.3% and 93%, respectively. To be observed
internal behavior in this system SCOD, NH3-N, and NO3-N were
conducted and removal shows range of 25~100%, 59~99%, and
70~100%, respectively.
Abstract: In this paper, we represent protein structure by using
graph. A protein structure database will become a graph database.
Each graph is represented by a spectral vector. We use Jacobi
rotation algorithm to calculate the eigenvalues of the normalized
Laplacian representation of adjacency matrix of graph. To measure
the similarity between two graphs, we calculate the Euclidean
distance between two graph spectral vectors. To cluster the graphs,
we use M-tree with the Euclidean distance to cluster spectral vectors.
Besides, M-tree can be used for graph searching in graph database.
Our proposal method was tested with graph database of 100 graphs
representing 100 protein structures downloaded from Protein Data
Bank (PDB) and we compare the result with the SCOP hierarchical
structure.
Abstract: This paper proposes a power-controlled scheduling scheme for devices using a directional antenna in smart home. In the case of the home network using directional antenna, devices can concurrently transmit data in the same frequency band. Accordingly, the throughput increases compared to that of devices using omni-directional antenna in proportional to the number of concurrent transmissions. Also, the number of concurrent transmissions depends on the beamwidth of antenna, the number of devices operating in the network , transmission power, interference and so on. In particular, the less transmission power is used, the more concurrent transmissions occur due to small transmission range. In this paper, we considered sub-optimal scheduling scheme for throughput maximization and power consumption minimization. In the scheme, each device is equipped with a directional antenna. Various beamwidths, path loss components, and antenna radiation efficiencies are considered. Numerical results show that the proposed schemes outperform the scheduling scheme using directional antennas without power control.
Abstract: The objective of the research was focused on the
design, development and evaluation of a sustainable web based
network system to be used as an interoperable environment for
University process workflow and document management. In this
manner the most of the process workflows in Universities can be
entirely realized electronically and promote integrated University.
Definition of the most used University process workflows enabled
creating electronic workflows and their execution on standard
workflow execution engines. Definition or reengineering of
workflows provided increased work efficiency and helped in having
standardized process through different faculties. The concept and the
process definition as well as the solution applied as Case study are
evaluated and findings are reported.
Abstract: Biological data has several characteristics that strongly differentiate it from typical business data. It is much more complex, usually large in size, and continuously changes. Until recently business data has been the main target for discovering trends, patterns or future expectations. However, with the recent rise in biotechnology, the powerful technology that was used for analyzing business data is now being applied to biological data. With the advanced technology at hand, the main trend in biological research is rapidly changing from structural DNA analysis to understanding cellular functions of the DNA sequences. DNA chips are now being used to perform experiments and DNA analysis processes are being used by researchers. Clustering is one of the important processes used for grouping together similar entities. There are many clustering algorithms such as hierarchical clustering, self-organizing maps, K-means clustering and so on. In this paper, we propose a clustering algorithm that imitates the ecosystem taking into account the features of biological data. We implemented the system using an Ant-Colony clustering algorithm. The system decides the number of clusters automatically. The system processes the input biological data, runs the Ant-Colony algorithm, draws the Topic Map, assigns clusters to the genes and displays the output. We tested the algorithm with a test data of 100 to1000 genes and 24 samples and show promising results for applying this algorithm to clustering DNA chip data.