Abstract: Concentric bracing systems have been in practice for many years because of their effectiveness in reducing seismic response. Depending on concept, seismic design codes provide various response modification factors (R), which itself consists of different terms, for different types of lateral load bearing systems but configuration of these systems are often ignored in the proposed values. This study aims at considering the effect of different x-bracing diagonal configuration on values of ductility dependent term in R computation. 51 models were created and nonlinear push over analysis has been performed. The main variables of this study were the suitable location of X–bracing diagonal configurations, which establishes better nonlinear behavior in concentric braced steel frames. Results show that some x-bracing diagonal configurations improve the seismic performance of CBF significantly and explicit consideration of lateral load bearing systems seems necessary.
Abstract: Diesel vehicle should be equipped with emission after-treatment devices as NOx reduction catalyst and particulate filtersin order to meet more stringer diesel emission standard. Urea-SCR is being developed as the most efficient method of reducing NOx emissions in the after-treatment devices of diesel engines, and recent studies have begun to mount the Urea-SCR device for diesel passenger cars and light duty vehicles. In the present study, the effects of the mixer on the efficiency of urea-SCR System (i.e., NH3uni- formityindex (NH3 UI) is investigated by predicting the transport phenomena in the urea-SCR system. The three dimensional Eulerian-Lagrangian CFD simulationfor internal flow and spray characteristics in front of SCR is carried out by using STAR-CCM+ 7.06 code. In addition, the paper proposes a method to minimize the wall-wetting around the urea injector in order to prevent injector blocks caused by solid urea loading.
Abstract: Effect of aging treatment on microstructural aspects of interfacial layers of the Cu/Al clad sheet produced by differential speed rolling (DSR) process were studied by electron back scattered diffraction (EBSD). Clad sheet of Al/Cu has been fabricated by using DSR, which caused severe shear deformation between Al and Cu plate to easily bond to each other. Rolling was carried out at 100oC with speed ratio of 2, in which the total thickness reduction was 45%. Interface layers of clad sheet were analyzed by EBSD after subsequent annealing at 400oC for 30 to 120min. With increasing annealing time, thickness of interface layer and fraction of high angle grain boundary were increased and average grain size was decreased.
Abstract: Urban planning is the need of the hour in a rapidly developing county like India. In essence, urban planning enhances the quality of land at a reasonable cost. Naya (New) Raipur is the new planned capital of the Indian state of Chhattisgarh, and is one of India’s few planned cities. Over the next decade it will drastically change the landscape of the state of Chhattisgarh. This new planned development is quintessential in growing this backward region and providing for future infrastructure. Key questions that arise are: How are people living in the surrounding region of New Raipur affected by its development? Are the affected people satisfied with compensation and rehabilitation that has been provided by the New Raipur Development Authority? To answer these questions, field research study in the form of questionnaires, interviews and site visits was conducted. To summarize the findings, while a majority of the surveyed population was dissatisfied with the rehabilitation and compensation provided by the New Raipur Development Authority, they were very positive about the success of the new development. Most thought that the new city would help their careers, improve job opportunities, improve prospects for their future generations, and benefit society as a whole.
To improve rehabilitation schemes for the future, the reasons for the negative sentiment brewing amongst the villagers regarding the monetary compensation was investigated. Most villagers deemed the monetary compensation to be lacking as they had squandered their financial windfall already. With numerous interviews and site visits, it was discovered that the lump sum form of monetary compensation was to blame. With a huge sum of money received at once and a lack of financial education, many villagers squandered this newly gained money on unnecessary purchases such as alcohol and expensive vehicles without investing for the long run in farmland and education for their children. One recommendation proposed to the New Raipur Development Authority (NRDA) for future monetary compensation design in times of rehabilitating people was to provide payments in installments rather than lump sums and educate the people about investing the compensation money wisely. This would save them from wasting money they receive and the ensuing dissatisfaction of squandering that money.
Abstract: Recently, the interest of globalization in the field of
teacher education has increased. In the U.S., the government is trying
to enhance the quality of education through a global approach in
education. To do so, the schools in the U.S. are recruiting teachers with
global capability from countries like Korea where competent teachers
are being trained. Meanwhile, in the case of Korea, although excellent
teachers have been cultivated every year, due to a low birth rate it is
not easy to become a domestic teacher. To solve the trouble that the
two countries are facing, the study first examines the demand and
necessity of globalization in the field of teacher education between
Korea and the U.S. Second, we propose a new project, called the
‘Global Teachers University (GTU)’ program to satisfy the demands
of both countries. Finally, we provide its implications to build the
future educational cooperation for teacher training in a global context.
Abstract: Advancement of communication technologies and smart devices in the recent times is leading to changes into the integrated wired and wireless communication environments. Since early days, businesses had started introducing environments for mobile device application to their operations in order to improve productivity (efficiency) and the closed corporate environment gradually shifted to an open structure. Recently, individual user's interest in working environment using mobile devices has increased and a new corporate working environment under the concept of BYOD is drawing attention. BYOD (bring your own device) is a concept where individuals bring in and use their own devices in business activities. Through BYOD, businesses can anticipate improved productivity (efficiency) and also a reduction in the cost of purchasing devices. However, as a result of security threats caused by frequent loss and theft of personal devices and corporate data leaks due to low security, companies are reluctant about adopting BYOD system. In addition, without considerations to diverse devices and connection environments, there are limitations in detecting abnormal behaviors, such as information leaks, using the existing network-based security equipment. This study suggests a method to detect abnormal behaviors according to individual behavioral patterns, rather than the existing signature-based malicious behavior detection, and discusses applications of this method in BYOD environment.
Abstract: In recent years Li-Ion batteries getting more attention among the Electrical Vehicles (EV) and Hybrid Electrical Vehicles (HEV) energy storage. Li-Ion has shown extended power density and light weight compared to other batteries readily available in the market. One of the major drawbacks in Li-Ion batteries is their sensitivity to the temperature. If the working temperature is beyond the limit, that could affect seriously on the durability and performance of Li-Ion battery. Thus Battery Thermal Management (BTM) is the most essential in adapting Li-Ion battery to the EVs and HEVs.
Abstract: RFID system, in which we give identification number to each item and detect it with radio frequency, supports more variable service than barcode system can do. For example, a refrigerator with RFID reader and internet connection will automatically notify expiration of food validity to us. But, in spite of its convenience, RFID system has some security threats, because anybody can get ID information of item easily. One of most critical threats is privacy invasion. Existing privacy protection schemes or systems have been proposed, and these schemes or systems defend normal users from attempts that any attacker tries to get information using RFID tag value. But, these systems still have weakness that attacker can get information using analogous value instead of original tag value. In this paper, we mention this type of attack more precisely and suggest 'Tag Broker Model', which can defend it. Tag broker in this model translates original tag value to random value, and user can only get random value. Attacker can not use analogous tag value, because he/she is not able to know original one from it.
Abstract: Due to environmental concerns, the recent regulation on automobile fuel economy has been strengthened. The market demand for efficient vehicles is growing and automakers to improve engine fuel efficiency in the industry have been paying a lot of effort. To improve the fuel efficiency, it is necessary to reduce losses or to improve combustion efficiency of the engine. VVA (Variable Valve Actuation) technology enhances the engine's intake air flow, reduce pumping losses and mechanical friction losses. And also, VVA technology is the engine's low speed and high speed operation to implement each of appropriate valve lift. It improves the performance of engine in the entire operating range. This paper presents a design procedure of DC motor and drive for VVA system and shows the validity of the design result by experimental result with prototype.
Abstract: A SCADA (Supervisory Control And Data
Acquisition) system is an industrial control and monitoring system for
national infrastructures. The SCADA systems were used in a closed
environment without considering about security functionality in the
past. As communication technology develops, they try to connect the
SCADA systems to an open network. Therefore, the security of the
SCADA systems has been an issue. The study of key management for
SCADA system also has been performed. However, existing key
management schemes for SCADA system such as SKE(Key
establishment for SCADA systems) and SKMA(Key management
scheme for SCADA systems) cannot support broadcasting
communication. To solve this problem, an Advanced Key
Management Architecture for Secure SCADA Communication has
been proposed by Choi et al.. Choi et al.-s scheme also has a problem
that it requires lots of computational cost for multicasting
communication. In this paper, we propose an enhanced scheme which
improving computational cost for multicasting communication with
considering the number of keys to be stored in a low power
communication device (RTU).
Abstract: In order to enhance the contrast in the regions where the pixels have similar intensities, this paper presents a new histogram equalization scheme. Conventional global equalization schemes over-equalizes these regions so that too bright or dark pixels are resulted and local equalization schemes produce unexpected discontinuities at the boundaries of the blocks. The proposed algorithm segments the original histogram into sub-histograms with reference to brightness level and equalizes each sub-histogram with the limited extents of equalization considering its mean and variance. The final image is determined as the weighted sum of the equalized images obtained by using the sub-histogram equalizations. By limiting the maximum and minimum ranges of equalization operations on individual sub-histograms, the over-equalization effect is eliminated. Also the result image does not miss feature information in low density histogram region since the remaining these area is applied separating equalization. This paper includes how to determine the segmentation points in the histogram. The proposed algorithm has been tested with more than 100 images having various contrasts in the images and the results are compared to the conventional approaches to show its superiority.
Abstract: Single crystals of Magnesium alloys such as pure Mg,
Mg-1Zn-0.5Y, Mg-0.1Y, and Mg-0.1Ce alloys were successfully
fabricated in this study by employing the modified Bridgman method.
To determine the exact orientation of crystals, pole figure
measurement using X-ray diffraction were carried out on each single
crystal. Hardness and compression tests were conducted followed by
subsequent recrysatllization annealing. Recrystallization kinetics of
Mg alloy single crystals has been investigated. Fabricated single
crystals were cut into rectangular shaped specimen and solution
treated at 400oC for 24 hrs, and then deformed in compression mode
by 30% reduction. Annealing treatment for recrystallization has been
conducted on these cold-rolled plates at temperatures of 300oC for
various times from 1 to 20 mins. The microstructure observation and
hardness measurement conducted on the recrystallized specimens
revealed that static recrystallization of ternary alloy single crystal was
very slow, while recrystallization behavior of binary alloy single
crystals appeared to be very fast.
Abstract: Flash memory has become an important storage device
in many embedded systems because of its high performance, low
power consumption and shock resistance. Multi-level cell (MLC) is
developed as an effective solution for reducing the cost and increasing
the storage density in recent years. However, most of flash file system
cannot handle the error correction sufficiently. To correct more errors
for MLC, we implement Reed-Solomon (RS) code to YAFFS, what is
widely used for flash-based file system. RS code has longer computing
time but the correcting ability is much higher than that of Hamming
code.
Abstract: This study develops a relation to explore the factors influencing management and technology capabilities in strategic alliances. Alliances between firms are recognizing increasingly popular as a vehicle to create and extract greater value from the market. Firm’s alliance can be described as the collaborative problem solving process to solve problems jointly. This study starts from research questions what factors of firm’s management and technology characteristics affect performance of firms which are formed alliances. In this study, we investigated the effect of strategic alliances on company performance. That is, we try to identify whether firms made an alliance with other organizations are differed by characteristics of management and technology. And we test that alliance type and alliance experiences moderate the relationship between firm’s capabilities and its performance. We employ problem-solving perspective and resource-based view perspective to shed light on this research questions. The empirical work is based on the Survey of Business Activities conducted from2006 to 2008 by Statistics Korea. We verify correlations between to point out that these results contribute new empirical evidence on the effect of strategic alliances on company performance.
Abstract: The study investigated the educational implications
that can be derived from the work of a variety of celebrated figures
such as Piaget, Vygotsky, and Bruner that will be helpful in the field
of language learning. However, the writer believed these views were
previously expressed not full–fledged by Comenius who has been
described by Howatt (1984) as a genius–the one that the history of
language teaching can claim. And we owe to him more than anyone.
Abstract: According to dramatic growth of internet services, an easy and prompt service deployment has been important for internet service providers to successfully maintain time-to-market. Before global service deployment, they have to pay the big cost for service evaluation to make a decision of the proper system location, system scale, service delay and so on. But, intra-Lab evaluation tends to have big gaps in the measured data compared with the realistic situation, because it is very difficult to accurately expect the local service environment, network congestion, service delay, network bandwidth and other factors. Therefore, to resolve or ease the upper problems, we propose multiple cloud based GPES Broker system and use case that helps internet service providers to alleviate the above problems in beta release phase and to make a prompt decision for their service launching. By supporting more realistic and reliable evaluation information, the proposed GPES Broker system saves the service release cost and enables internet service provider to make a prompt decision about their service launching to various remote regions.
Abstract: The most common forensic activity is searching a hard
disk for string of data. Nowadays, investigators and analysts are
increasingly experiencing large, even terabyte sized data sets when
conducting digital investigations. Therefore consecutive searching can
take weeks to complete successfully. There are two primary search
methods: index-based search and bitwise search. Index-based
searching is very fast after the initial indexing but initial indexing
takes a long time. In this paper, we discuss a high speed bitwise search
model for large-scale digital forensic investigations. We used pattern
matching board, which is generally used for network security, to
search for string and complex regular expressions. Our results indicate
that in many cases, the use of pattern matching board can substantially
increase the performance of digital forensic search tools.
Abstract: In order to enhance the aircraft survivability, the
infrared signatures emitted by hot engine parts should be determined
exactly. For its reduction it is necessary for the rear fuselage
temperature to be decreased. In this study, numerical modeling of flow
fields and heat transfer characteristics of an aircraft nozzle is
performed and its temperature distribution along each component wall
is predicted. The radiation shield is expected to reduce the skin
temperature of rear fuselage. The effect of material characteristic of
radiation shield on the heat transfer is also investigated. Through this
numerical analysis, design parameters related to the susceptibility of
aircraft are examined.
Abstract: WikID is a wiki for industrial design engineers. An
important aspect for the viability of a wiki is the loyalty of the user
community to share their information and knowledge by adding this
knowledge to the wiki. For the initiators of a wiki it is therefore
important to use every aspect to stimulate the user community to
actively participate. In this study the focus is on the styling of the
website. The central question is: How could the WikID website be
visually designed to achieve a user experience which will incite the
user to actively participate in the WikID community? After a
literature study on the influencing factors of a website, a new
interface has been designed by applying the rules found, in order to
expand this website-s active user community. An online
questionnaire regarding the old or the new website gave insights in
the opinions of users. As expected, the new website was rated more
positively than the old website. However, the differences are limited.
Abstract: Until recently, researchers have developed various
tools and methodologies for effective clinical decision-making.
Among those decisions, chest pain diseases have been one of
important diagnostic issues especially in an emergency department. To
improve the ability of physicians in diagnosis, many researchers have
developed diagnosis intelligence by using machine learning and data
mining. However, most of the conventional methodologies have been
generally based on a single classifier for disease classification and
prediction, which shows moderate performance. This study utilizes an
ensemble strategy to combine multiple different classifiers to help
physicians diagnose chest pain diseases more accurately than ever.
Specifically the ensemble strategy is applied by using the integration
of decision trees, neural networks, and support vector machines. The
ensemble models are applied to real-world emergency data. This study
shows that the performance of the ensemble models is superior to each
of single classifiers.