Abstract: In this paper, different approaches to solve the
forward kinematics of a three DOF actuator redundant hydraulic
parallel manipulator are presented. On the contrary to series
manipulators, the forward kinematic map of parallel manipulators
involves highly coupled nonlinear equations, which are almost
impossible to solve analytically. The proposed methods are using
neural networks identification with different structures to solve the
problem. The accuracy of the results of each method is analyzed in
detail and the advantages and the disadvantages of them in
computing the forward kinematic map of the given mechanism is
discussed in detail. It is concluded that ANFIS presents the best
performance compared to MLP, RBF and PNN networks in this
particular application.
Abstract: The study in this paper underlines the importance of
correct joint selection of the spreading codes for uplink of multicarrier
code division multiple access (MC-CDMA) at the transmitter
side and detector at the receiver side in the presence of nonlinear
distortion due to high power amplifier (HPA). The bit error rate
(BER) of system for different spreading sequences (Walsh code, Gold
code, orthogonal Gold code, Golay code and Zadoff-Chu code) and
different kinds of receivers (minimum mean-square error receiver
(MMSE-MUD) and microstatistic multi-user receiver (MSF-MUD))
is compared by means of simulations for MC-CDMA transmission
system. Finally, the results of analysis will show, that the application
of MSF-MUD in combination with Golay codes can outperform
significantly the other tested spreading codes and receivers for all
mostly used models of HPA.
Abstract: This article presents the simulation, parameterization and optimization of an electromagnet with the C–shaped configuration, intended for the study of magnetic properties of materials. The electromagnet studied consists of a C-shaped yoke, which provides self–shielding for minimizing losses of magnetic flux density, two poles of high magnetic permeability and power coils wound on the poles. The main physical variable studied was the static magnetic flux density in a column within the gap between the poles, with 4cm2 of square cross section and a length of 5cm, seeking a suitable set of parameters that allow us to achieve a uniform magnetic flux density of 1x104 Gaussor values above this in the column, when the system operates at room temperature and with a current consumption not exceeding 5A. By means of a magnetostatic analysis by the finite element method, the magnetic flux density and the distribution of the magnetic field lines were visualized and quantified. From the results obtained by simulating an initial configuration of electromagnet, a structural optimization of the geometry of the adjustable caps for the ends of the poles was performed. The magnetic permeability effect of the soft magnetic materials used in the poles system, such as low– carbon steel (0.08% C), Permalloy (45% Ni, 54.7% Fe) and Mumetal (21.2% Fe, 78.5% Ni), was also evaluated. The intensity and uniformity of the magnetic field in the gap showed a high dependence with the factors described above. The magnetic field achieved in the column was uniform and its magnitude ranged between 1.5x104 Gauss and 1.9x104 Gauss according to the material of the pole used, with the possibility of increasing the magnetic field by choosing a suitable geometry of the cap, introducing a cooling system for the coils and adjusting the spacing between the poles. This makes the device a versatile and scalable tool to generate the magnetic field necessary to perform magnetic characterization of materials by techniques such as vibrating sample magnetometry (VSM), Hall-effect, Kerr-effect magnetometry, among others. Additionally, a CAD design of the modules of the electromagnet is presented in order to facilitate the construction and scaling of the physical device.
Abstract: Hexavalent chromium is highly toxic to most living organisms and a known human carcinogen by the inhalation route of exposure. Therefore, treatment of Cr(VI) contaminated wastewater is essential before their discharge to the natural water bodies. Cr(VI) reduction to Cr(III) can be beneficial because a more mobile and more toxic chromium species is converted to a less mobile and less toxic form. Zero-valence-state metals, such as scrap iron, can serve as electron donors for reducing Cr(VI) to Cr(III). The influence of pH on scrap iron capacity to reduce Cr(VI) was investigated in this study. Maximum reduction capacity of scrap iron was observed at the beginning of the column experiments; the lower the pH, the greater the experiment duration with maximum scrap iron reduction capacity. The experimental results showed that highest maximum reduction capacity of scrap iron was 12.5 mg Cr(VI)/g scrap iron, at pH 2.0, and decreased with increasing pH up to 1.9 mg Cr(VI)/g scrap iron at pH = 7.3.
Abstract: With the advent of emerging personal computing paradigms such as ubiquitous and mobile computing, Web contents are becoming accessible from a wide range of mobile devices. Since these devices do not have the same rendering capabilities, Web contents need to be adapted for transparent access from a variety of client agents. Such content adaptation is exploited for either an individual element or a set of consecutive elements in a Web document and results in better rendering and faster delivery to the client device. Nevertheless, Web content adaptation sets new challenges for semantic markup. This paper presents an advanced components platform, called SMC, enabling the development of mobility applications and services according to a channel model based on the principles of Services Oriented Architecture (SOA). It then goes on to describe the potential for integration with the Semantic Web through a novel framework of external semantic annotation that prescribes a scheme for representing semantic markup files and a way of associating Web documents with these external annotations. The role of semantic annotation in this framework is to describe the contents of individual documents themselves, assuring the preservation of the semantics during the process of adapting content rendering. Semantic Web content adaptation is a way of adding value to Web contents and facilitates repurposing of Web contents (enhanced browsing, Web Services location and access, etc).
Abstract: This paper is motivated by the aspect of uncertainty in
financial decision making, and how artificial intelligence and soft
computing, with its uncertainty reducing aspects can be used for
algorithmic trading applications that trade in high frequency.
This paper presents an optimized high frequency trading system that
has been combined with various moving averages to produce a hybrid
system that outperforms trading systems that rely solely on moving
averages. The paper optimizes an adaptive neuro-fuzzy inference
system that takes both the price and its moving average as input,
learns to predict price movements from training data consisting of
intraday data, dynamically switches between the best performing
moving averages, and performs decision making of when to buy or
sell a certain currency in high frequency.
Abstract: The decoding of Low-Density Parity-Check (LDPC) codes is operated over a redundant structure known as the bipartite graph, meaning that the full set of bit nodes is not absolutely necessary for decoder convergence. In 2008, Soyjaudah and Catherine designed a recovery algorithm for LDPC codes based on this assumption and showed that the error-correcting performance of their codes outperformed conventional LDPC Codes. In this work, the use of the recovery algorithm is further explored to test the performance of LDPC codes while the number of iterations is progressively increased. For experiments conducted with small blocklengths of up to 800 bits and number of iterations of up to 2000, the results interestingly demonstrate that contrary to conventional wisdom, the error-correcting performance keeps increasing with increasing number of iterations.
Abstract: There are three approaches to complete Bayesian
Network (BN) model construction: total expert-centred, total datacentred,
and semi data-centred. These three approaches constitute the
basis of the empirical investigation undertaken and reported in this
paper. The objective is to determine, amongst these three
approaches, which is the optimal approach for the construction of a
BN-based model for the performance assessment of students-
laboratory work in a virtual electronic laboratory environment. BN
models were constructed using all three approaches, with respect to
the focus domain, and compared using a set of optimality criteria. In
addition, the impact of the size and source of the training, on the
performance of total data-centred and semi data-centred models was
investigated. The results of the investigation provide additional
insight for BN model constructors and contribute to literature
providing supportive evidence for the conceptual feasibility and
efficiency of structure and parameter learning from data. In addition,
the results highlight other interesting themes.
Abstract: Active Vibration Control (AVC) is an important
problem in structures. One of the ways to tackle this problem is to
make the structure smart, adaptive and self-controlling. The objective
of active vibration control is to reduce the vibration of a system by
automatic modification of the system-s structural response. This
paper features the modeling and design of a Periodic Output
Feedback (POF) control technique for the active vibration control of
a flexible Timoshenko cantilever beam for a multivariable case with
2 inputs and 2 outputs by retaining the first 2 dominant vibratory
modes using the smart structure concept. The entire structure is
modeled in state space form using the concept of piezoelectric
theory, Timoshenko beam theory, Finite Element Method (FEM) and
the state space techniques. Simulations are performed in MATLAB.
The effect of placing the sensor / actuator at 2 finite element
locations along the length of the beam is observed. The open loop
responses, closed loop responses and the tip displacements with and
without the controller are obtained and the performance of the smart
system is evaluated for active vibration control.
Abstract: The Comparison analysis of the Wald-s and Bayestype sequential methods for testing hypotheses is offered. The merits of the new sequential test are: universality which consists in optimality (with given criteria) and uniformity of decision-making regions for any number of hypotheses; simplicity, convenience and uniformity of the algorithms of their realization; reliability of the obtained results and an opportunity of providing the errors probabilities of desirable values. There are given the Computation results of concrete examples which confirm the above-stated characteristics of the new method and characterize the considered methods in regard to each other.
Abstract: In this paper, an analytical modeling is presentated to
describe the channel noise in GME SGT/CGT MOSFET, based on
explicit functions of MOSFETs geometry and biasing conditions for
all channel length down to deep submicron and is verified with the
experimental data. Results shows the impact of various parameters
such as gate bias, drain bias, channel length ,device diameter and gate
material work function difference on drain current noise spectral
density of the device reflecting its applicability for circuit design
applications.
Abstract: This paper presents the convergence analysis
of a prediction based blind equalizer for IIR channels.
Predictor parameters are estimated by using the recursive
least squares algorithm. It is shown that the prediction
error converges almost surely (a.s.) toward a scalar
multiple of the unknown input symbol sequence. It is
also proved that the convergence rate of the parameter
estimation error is of the same order as that in the iterated
logarithm law.
Abstract: Computerized alarm systems have been applied
increasingly to nuclear power plants. For existing plants, an add-on
computer alarm system is often installed to the control rooms. Alarm
avalanches during the plant transients are major problems with the
alarm systems in nuclear power plants. Computerized alarm systems
can process alarms to reduce the number of alarms during the plant
transients. This paper describes various alarm processing methods, an
alarm cause tracking function, and various alarm presentation schemes
to show alarm information to the operators effectively which are
considered during the development of several computerized alarm
systems for Korean nuclear power plants and are found to be helpful to
the operators.
Abstract: In many buildings we rely on large footings to offer
structural stability. Designers often compensate for the lack of
knowledge available with regard to foundation-soil interaction by
furnishing structures with overly large footings. This may lead to a
significant increase in building expenditures if many large
foundations are present. This paper describes the interface material
law that governs the behavior along the contact surface of adjacent
materials, and the behavior of a large foundation under ultimate limit
loading. A case study is chosen that represents a common
foundation-soil system frequently used in general practice and
therefore relevant to other structures. Investigations include
compressing versus uplifting wind forces, alterations to the
foundation size and subgrade compositions, the role of the slab
stiffness and presence and the effect of commonly used structural
joints and connections. These investigations aim to provide the
reader with an objective design approach, efficiently preventing
structural instability.
Abstract: Biological Ammonia removal (nitrification), the
oxidation of ammonia to nitrate catalyzed by bacteria, is a key part of
global nitrogen cycling. In the first step of nitrification,
chemolithoautotrophic ammonia oxidizer transform ammonia to
nitrite, this subsequently oxidized to nitrate by nitrite oxidizing
bacteria. This process can be affected by several factors. In this study
the effect of influent COD on biological ammonia removal in a
bench-scale biological reactor was investigated. Experiments were
carried out using synthetic wastewater. The initial ammonium
concentration was 25mgNH4
+-N L-1. The effect of COD between
247.55±1.8 and 601.08±3.24mgL-1 on biological ammonia removal
was investigated by varying the COD loading supplied to reactor.
From the results obtained in this study it could be concluded in the
range of 247.55±1.8 to 351.35±2.05mgL-1, there is a direct
relationship between amount of COD and ammonia removal.
However more than 351.35±2.05 up to 601.08±3.24mgL-1 were
found an indirect relationship between them.
Abstract: This paper present a MATLAB-SIMULINK model of a single phase 2.5 KVA, 240V RMS controlled PV VSI (Photovoltaic Voltage Source Inverter) inverter using IGBTs (Insulated Gate Bipolar Transistor). The behavior of output voltage, output current, and the total harmonic distortion (THD), with the variation in input dc blocking capacitor (Cdc), for linear and non-linear load has been analyzed. The values of Cdc as suggested by the other authors in their papers are not clearly defined and it poses difficulty in selecting the proper value. As the dc power stored in Cdc, (generally placed parallel with battery) is used as input to the VSI inverter. The simulation results shows the variation in the output voltage and current with different values of Cdc for linear and non-linear load connected at the output side of PV VSI inverter and suggest the selection of suitable value of Cdc.
Abstract: This paper presents the comparison ageing deterioration of silicone rubber housing material for outdoor polymer insulators by using salt fog ageing test based on IEC 61109 and outdoor exposure test.Four types of high temperature silicone vulcanized silicone rubber sheet with different amount of ATH were used as testing specimen. For salt fog ageing test, the specimens were tested continuously 1000 hours with energized in test chamber. For outdoor exposure test, the specimens were hung continuously 18 months without energized. Physical and chemical analyses were conducted to evaluate degree of ageing deterioration of tested specimens. Slightly surface erosion was observed on specimen surface after salt fog ageing test and no erosion was observed on surface of outdoor exposure specimen. However, comparable degree of ageing deterioration can be seen from surface analysis results.
Abstract: The complex hybrid and nonlinear nature of many processes that are met in practice causes problems with both structure modelling and parameter identification; therefore, obtaining a model that is suitable for MPC is often a difficult task. The basic idea of this paper is to present an identification method for a piecewise affine (PWA) model based on a fuzzy clustering algorithm. First we introduce the PWA model. Next, we tackle the identification method. We treat the fuzzy clustering algorithm, deal with the projections of the fuzzy clusters into the input space of the PWA model and explain the estimation of the parameters of the PWA model by means of a modified least-squares method. Furthermore, we verify the usability of the proposed identification approach on a hybrid nonlinear batch reactor example. The result suggest that the batch reactor can be efficiently identified and thus formulated as a PWA model, which can eventually be used for model predictive control purposes.
Abstract: Property investment in the real estate industry has a
high risk due to the uncertainty factors that will affect the decisions
made and high cost. Analytic hierarchy process has existed for some
time in which referred to an expert-s opinion to measure the
uncertainty of the risk factors for the risk analysis. Therefore,
different level of experts- experiences will create different opinion
and lead to the conflict among the experts in the field. The objective
of this paper is to propose a new technique to measure the uncertainty
of the risk factors based on multidimensional data model and data
mining techniques as deterministic approach. The propose technique
consist of a basic framework which includes four modules: user,
technology, end-user access tools and applications. The property
investment risk analysis defines as a micro level analysis as the
features of the property will be considered in the analysis in this
paper.
Abstract: The aim of our work is to study phase composition,
particle size and magnetic response of Fe2O3/TiO2 nanocomposites
with respect to the final annealing temperature. Those nanomaterials
are considered as smart catalysts, separable from a liquid/gaseous
phase by applied magnetic field. The starting product was obtained
by an ecologically acceptable route, based on heterogeneous
precipitation of the TiO2 on modified g-Fe2O3 nanocrystals dispersed
in water. The precursor was subsequently annealed on air at
temperatures ranging from 200 oC to 900 oC. The samples were
investigated by synchrotron X-ray powder diffraction (S-PXRD),
magnetic measurements and Mössbauer spectroscopy. As evidenced
by S-PXRD and Mössbauer spectroscopy, increasing the annealing
temperature causes evolution of the phase composition from
anatase/maghemite to rutile/hematite, finally above 700 oC the
pseudobrookite (Fe2TiO5) also forms. The apparent particle size of
the various Fe2O3/TiO2 phases has been determined from the highquality
S-PXRD data by using two different approaches: the Rietveld
refinement and the Debye method. Magnetic response of the samples
is discussed in considering the phase composition and the particle
size.